FCC ID: 2AJOTTA-1206 Multi-band GSM/WCDMA/LTE phone with Bluetooth, WLAN

Get Started Nokia xx Camera Flash USB connector Loudspeaker Microphone TA-1206/TA-1211 EN 1. Insert the SIM and memory card 1. Open the SIM card tray: push the tray opener pin in the tray hole and slide the tray out. 2. Put the nano-SIM in slot 1 on the tray with the contact area face down. If you have a dual-SIM phone, put the second SIM in slot 2. 3. If you have a memory card, put it in the memory card slot. 4. Slide the tray back in. Use only original nano-SIM cards. Use of incompatible SIM cards may damage the card or the device, and may corrupt data stored on the card. Use only compatible memory cards approved for use with this device. Incompatible cards may damage the card and the device and corrupt data stored on the card. Important: Do not remove the memory card when an app is using it. Doing so may damage the memory card and the device and corrupt data stored on the card. Both SIM cards are available at the same time when the device is not being used, but while one SIM card is active, for example, making a call, the other may be unavailable. 711608029031 V1.0 xxxxxxxxxx Front camera Earpiece Headset connector SIM and memory card slot Google Assistant/

Google Search key*

Volume keys Power/Lock key

*The Google Assistant is available in selected markets and languages. Where not available, the Google Assistant is replaced by Google Search. Check availability at https://support.google.com/assistant. 2. Charge the battery and switch the phone on Plug a compatible charger into a wall outlet, and connect the cable to your phone. Your phone supports the USB micro-B cable. You can also charge your phone from a computer with a USB cable, but it may take a longer time. If the battery is completely discharged, it may take several minutes before the charging indicator is displayed. To switch your phone on, press and hold the power key until the phone vibrates. The phone guides you through the setup. For an online user guide and troubleshooting help, go to www.nokia.com/mobile-support. equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device has an electronic label for certification information. To access it, select Settings > System > Certification. 2019 HMD Global. HMD Global Oy is the exclusive licensee of the Nokia brand for phones & tablets. Nokia is a registered trademark of Nokia Corporation. Android, Google and other related marks and logos are trademarks of Google LLC. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by HMD Global is under license. Product and safety info Important: For important info on the safe use of your device and battery, read the Product and safety info booklet before you take your device into use. You can only use your device on the GSM 850, 900, 1800, 1900;

WCDMA 1, 5, 8; LTE 1, 3, 5, 7, 8, 20, 28, 38, 40, 41 (2535 - 2655 MHz) networks. You need a subscription with a service provider. Important: 4G/LTE might not be supported by your network service provider or by the service provider you are using when traveling. In these cases, you may not be able to make or receive calls, send or receive messages or use mobile data connections. To make sure your device works seamlessly when full 4G/LTE service is not available, it is recommended that you change the highest connection speed from 4G to 3G. To do this, on the home screen, tap Settings > Network & Internet > Mobile network > Advanced, and switch Preferred network type to 3G. For more info, contact your network service provider. Maximum transmit power GSM 850, 900 GSM 1800, 1900 WCDMA 1, 5, 8 LTE 1, 3, 5, 7, 8, 20, 28, 38, 40, 41 Bluetooth WLAN 2.4G 35 dBm 32 dBm 25 dBm 25 dBm 7.5 dBm 18 dBm Your device has an internal, non-removable, rechargeable battery. Do not attempt to remove the battery or back cover, as you may damage the device. To replace the battery, take the device to the nearest authorised service facility. Charge your device with the CH-35E (EU plug) / CH-35X (UK plug) /

CH-35U (US plug) / CH-35A (Australia plug) / FC0208 (Argentina plug) / CH-35N (India plug) chargers. HMD Global may make additional battery or charger models available for this device. Charging time can vary depending on device capability. Some of the accessories mentioned in this user guide, such as charger, headset, or data cable, may be sold separately. The surface of the device is nickel-free. Parts of the device are magnetic. Metallic materials may be attracted to the device. Do not place credit cards or other magnetic stripe cards near the device for extended periods of time, since the cards may be damaged. Note: Pre-installed system software and apps use a significant part of memory space. Keep a safe distance when using the flash. Do not use the flash on people or animals at close range. Do not cover the flash while taking a photo. Certification information (SAR) This mobile device meets guidelines for exposure to radio waves as set forth by the Council of Europe (CE). Refer to the following. European RF Exposure Information Your mobile device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves recommended by international guidelines. These guidelines were developed by the independent scientific organization ICNIRP and include safety margins designed to assure the protection of all persons, regardless of age and health. The guidelines use a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit for mobile devices is 2.0 W/kg and the highest SAR value for this device when tested at the ear is 0.41 W/kg*. As mobile devices offer a range of functions, they can be used in other positions, such as on the body. In this case, the highest tested SAR value is 1.4 W/kg* at the separation distance of 0.5 cm from the body. For electronic safety, maintain the separation distance with accessories containing no metal, that position handset a minimum of the above distance. Use of other accessories may not ensure compliance with RF exposure guidelines.

*The tests are carried out in accordance with international guidelines for testing. This mobile device meets guidelines for exposure to radio waves as set forth by the Federal Communications Commission (FCC). Refer to the following. FCC RF Exposure Information Your handset is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The guidelines are based on standards that were developed by independent scientific organization through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless handsets employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. The tests are performed in positions and locations (e.g. at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this handset model as reported to the FCC when tested for use at the ear is 0.54 W/kg (TA-1206)/0.81 W/kg (TA-1211) and when worn on the body in a holder or carry case, is 1.23 W/kg (TA-1206)/0.86 W/kg

(TA-1211). Body-worn Operation; This device was tested for typical body-worn operations with the handset kept 1.0 cm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 1.0 cm separation distance between the users body and the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. The FCC has granted an Equipment Authorization for this handset model with all reported SAR levels evaluated as in compliance with the FCC RF emission guidelines. SAR information on this handset model is on file with the FCC and can be found under the FCC ID Search section of www.fcc.gov/oet/ea/ after searching on FCC ID 2AJOTTA-1206 and 2AJOTTA-1211. Additional information on Specific Absorption Rates (SAR) can be found on the FCC website at www.fcc.gov/general/radio-

frequency-safety-0. To send data or messages, a good connection to the network is needed. Sending may be delayed until such a connection is available. Follow the separation distance instructions until the sending is finished. During general use, the SAR values are usually well below the values stated above. This is because, for purposes of system efficiency and to minimise interference on the network, the operating power of your mobile is automatically decreased when full power is not needed for the call. The lower the power output, the lower the SAR value. Device models may have different versions and more than one value. Component and design changes may occur over time and some changes could affect SAR values. For more info, go to www.sar-tick.com. Note that mobile devices may be transmitting even if you are not making a voice call. Your mobile device is also designed to meet the United States Federal Communications Commission (FCC) guidelines. FCC ratings for your device and more information on SAR can be found at http:/

/transition.fcc.gov/oet/rfsafety/sar.html. The World Health Organization (WHO) has stated that current scientific information does not indicate the need for any special precautions when using mobile devices. If you are interested in reducing your exposure, they recommend you limit your usage or use a hands-free kit to keep the device away from your head and body. For more information and explanations and discussions on RF exposure, go to the WHO website at www.who.int/peh-emf/en. Copyrights and other notices EU Declaration of Conformity Hereby, HMD Global Oy declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. A copy of the EU Declaration of Conformity can be found at https://

www.nokia.com/en_int/phones/declaration-of-conformity. FCC notice:

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For more info, go to www.fcc.gov/

engineering-technology/electromagnetic-compatibility-division/

radio-frequency-safety/faq/rf-safety. Any changes or modifications not expressly approved by HMD Global could void the users authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

Designed by HMD Global Oy Bertel Jungin aukio 9, 02600 Espoo, Finland Model TA-1206 FCC ID: 2AJOTTA-1206 Made in China Cex

Declaration of changes from sku2 TA-1214 to sku1 TA-1206 SOFTWARE MODIFICATIONS:

Protocol Stack changes: No MMS/STK/USAT/USIM changes: No DM/SUPL/VT/FUMO/SWP/HCI: No Other changes detailed: Change TA-Code from TA-1214 to TA-1206 HARDWARE MODIFICATIONS:

Band changes: No PCB Layout changes: No Main components changes:

Antenn a Base Band Transceive r ASM Power Amplifier Yes NA NA Yes Yes Yes Yes Yes Yes GSM850 GSM900 GSM1800 GSM1900 Yes UMTS2100 UMTS1900 NA UMTS1700 NA Yes UMTS850 UMTS900 LTE 1 LTE 2 LTE 3 LTE 4 LTE 5 LTE 7 LTE 8 LTE 12 LTE 17 LTE 20 LTE 28 LTE 38 LTE 40 LTE 41 LTE 66 Bluetooth WiFi NFC Yes Yes Yes Yes Yes Yes Yes Yes NO NO NA NA NA NA NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NA NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NA NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NA NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NO NA Tx SAW Filter NO NO NO NO NO NA NA NO NO NO NA NO NA NO NO NO NA NA NO NO YES YES YES NA NO NO NA Rx SAW Filter NO NO NO YES Duplex er NO NO NO YES NO NA NA NO NO NO NA NO NA NO NO NO NA NA NO NO YES YES YES NA NO NO NA NO NA NA NO NO NO NA NO NA NO NO NO NA NA NA NO NO NO NO NA NO NO NA FM changes: No Other components changes:

LCD/ Speaker/ Camera/ Vibrator changes: No Other changes detailed: TA-1214 is single SIM, TA-1206 is dual SIM MECHANICAL MODIFICATIONS:

Use new metal front/back cover or keypad: No Mechanical shell changes:No Whole size of EUT: No Distance of Ear reference point to bottom of handset: No Other trinkets to change the surface of handset: No Other changes detailed: No APPROVED BY:

Project Manager: LIU HAO Signature:

Date: 2019-9-9

HMD Global Oy Bertel Jungin aukio 9 Tel +358 86 4213499 Fax +358 45 2133756 02600 Espoo, Finland Authority to Act as Agent Date: ___2019-10-16_____ American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern:

______ CTTL, Telecommunication Technology Labs, CAICT ____ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date:

_____12 months____ By: _____ __Rosario Casillo_____

(Signature)

(Print name) ___Director Technology and Compliance ______ Title:

On behalf of: _______ HMD Global Oy__________

(Company Name) HMD Global Oy is the exclusive licensee of the Nokia brand for phones & tablets. Nokia is a registered trademark of the Nokia Corporation. HMD Global Oy Bertel Jungin aukio 9 Tel +358 86 4213499 Fax +358 45 2133756 02600 Espoo, Finland Request for Confidentiality Date: _2019-10-16______ Subject: Confidentiality Request for: ______2AJOTTA-1206 __ Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 9.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent *1 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent *3 Users Manual 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at:

https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 1 - Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-

Confidentiality.pdf for complete details. 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. HMD Global Oy is the exclusive licensee of the Nokia brand for phones & tablets. Nokia is a registered trademark of the Nokia Corporation. HMD Global Oy Bertel Jungin aukio 9 Tel +358 86 4213499 Fax +358 45 2133756 02600 Espoo, Finland _____ HMD Global Oy _____ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to

"competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of _180_ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications:

IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By: ___ __________________ __________________

(Signature/Title)

(Print name) HMD Global Oy is the exclusive licensee of the Nokia brand for phones & tablets. Nokia is a registered trademark of the Nokia Corporation. Rosario Casillo

Date: Oct. 30, 19 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request permission to use GSM/UMTS/LTE/Wi-Fi/BT test results from model TA-1214 in our applications for model TA-1206 FCC ID: 2AJOTTA-1206 To whom it may concern:

We request permission to partially use GSM/UMTS/LTE/Wi-Fi /BT test results from model TA-1214 (FCC ID: 2AJOTTA-1214) in our applications for model TA-1206

(FCC ID: 2AJOTTA-1206). You can find details next page:

For the above, we performed full test for SAR, and partially re-used the test results of TA-1214 for other parts, shown as below. For details, please refer to the relevant test reports. Item GSM Part Test done on the new model GSM mobile phone FCC certification part22/24 testing on GSM850 and Radiated Output Power and Emission Limit PCS1900 UMTS Part UMTS mobile phone FCC certification part22 testing on WCDMA Band V Radiated Output Power and Emission Limit LTE Part LTE mobile phone FCC certification part22/27 testing on LTE Band 5 and Radiated Output Power and Emission Limit Band 7 LTE mobile phone FCC certification part27 testing on LTE Band 41 Full test BT Part BT LE with EDR FCC certification part15C testing WiFi Part WiFi 802.11b/g/n 2.4G FCC certification part15C testing Sincerely yours, Spot check on Output Power Spot check on Output Power Zi Xiaogang

02600 Espoo, Fax +358 45 2133756 Tel +358 86 4213499 HMD Global Oy Bertel Jungin aukio 9, Finland HMD global Oy Bertel Jungin aukio 9, 02600 Espoo, Finland Statement We, HMD global Oy, declare that our devices, Model name: TA-1206 with FCC ID:

2AJOTTA-1206 and Model name: TA-1211 with FCC ID: 2AJOTTA-1211 , are multi-bands mobile phones which support GSM 850/900/1800/1900, WCDMA Band 1/5/8, LTE Bands 1/3/5/7/8/20/28/38/40/41, with WLAN 802.11 b/n/g 2.4GHz, and Bluetooth functionality. The hardware supports LTE Band 40, but it will be disabled by software and it will not be operational in US and Canada market. Rosario Casillo Director Technology and Compliance rosario.casillo@hmdglobal.com HMD Global Oy is the exclusive licensee of the Nokia brand for phones & tablets. Nokia is a registered trademark of the Nokia Corporation.