FCC ID: 2AJOTTA-1412 Multi-band GSM/WCDMA/LTE phone with Bluetooth&WLAN

Get Started Nokia xx 4 3 6 5 13 2 1 8 10 7 9 11 12 1. Microphone 2. Loudspeaker 3. Camera 4. Flash 5. Google Assistant/Google Search key*

6. SIM and memory card slot 7. Front camera 8. Headset connector 9. Microphone 10. Earpiece 11. Volume keys 12. Power/Lock key, Fingerprint sensor 13. USB connector TA-1404/TA-1412 EN-LATAM

*Google Assistant is not available in certain languages and countries. Where not available, Google Assistant is replaced by Google Search. Check availability at https://support.google.com/assistant. 2. Charge the battery and switch the phone on Plug a compatible charger into a wall outlet, and connect the cable to your phone. Your phone supports the USB-C cable. You can also charge your phone from a computer with a USB cable, but it may take a longer time. If the battery is completely discharged, it may take several minutes before the charging indicator is displayed. To switch your phone on, press and hold the power key until the phone vibrates. The phone guides you through the setup. For an online user guide and troubleshooting help, go to www.nokia.com/mobile-support. 1. Insert the SIM and memory card 1.Open the SIM card tray: push the tray opener pin in the tray hole and slide the tray out. 2. Put the nano-SIM in the SIM slot on the tray with the contact area face down. 3. If you have a dual-SIM phone, put the second SIM in the SIM2 slot. Tip: To find out if your phone can use 2 SIM cards, see the label on the sales box. If there are 2 IMEI codes on the label, you have a dual-SIM phone. 4. If you have a memory card, put it in the memory card slot. 5. Slide the tray back in. Use only original nano-SIM cards. Use of incompati-

ble SIM cards may damage the card or the device, and may corrupt data stored on the card. Use only compatible memory cards approved for use with this device. Incompatible cards may dam-

age the card and the device and corrupt data stored on the card. Important: Do not remove the memory card when an app is using it. Doing so may damage the memory card and the device and corrupt data stored on the card. Both SIM cards are available at the same time when the device is not being used, but while one SIM card is active, for example, making a call, the other may be unavailable. 711608060361 V1.0 accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. The FCC has granted an Equipment Authorization for this handset model with all reported SAR levels evaluated as in compliance with the FCC RF emission guidelines. SAR information on this handset model is on file with the FCC and can be found under the FCC ID Search section of www.fcc.gov/oet/ea/ after searching on FCC ID 2AJOTTA-1404 or 2AJOTTA-1412. Additional information on Specific Absorption Rates (SAR) can be found on the FCC website at www.fcc.gov/general/radio-frequency-

safety-0. To send data or messages, a good connection to the network is needed. Sending may be delayed until such a connection is available. Follow the separation distance instructions until the sending is finished. During general use, the SAR values are usually well below the values stated above. This is because, for purposes of system efficiency and to minimise interference on the network, the operating power of your mobile is automatically decreased when full power is not needed for the call. The lower the power output, the lower the SAR value. Device models may have different versions and more than one value. Component and design changes may occur over time and some changes could affect SAR values. For more info, go to www.sar-tick.com. Note that mobile devices may be transmitting even if you are not making a voice call. Your mobile device is also designed to meet the United States Federal Communications Commission (FCC) guidelines. FCC ratings for your device and more information on SAR can be found at http:/

/transition.fcc.gov/oet/rfsafety/sar.html. The World Health Organization (WHO) has stated that current scientific information does not indicate the need for any special precautions when using mobile devices. If you are interested in reducing your exposure, they recommend you limit your usage or use a hands-free kit to keep the device away from your head and body. For more information and explanations and discussions on RF exposure, go to the WHO website at www.who.int/peh-emf/en. Copyrights and other notices FCC notice:

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For more info, go to www.fcc.gov/engineering-

technology/electromagnetic-compatibility-division/radio-

frequency-safety/faq/rf-safety. Any changes or modifications not expressly approved by HMD Global could void the users authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device has an electronic label for certification information. To access it, select Settings > System > Certification. 2022 HMD Global. HMD Global Oy is the exclusive licensee of the Nokia brand for phones & tablets. Nokia is a registered trademark of Nokia Corporation. Android, Google and other related marks and logos are trademarks of Google LLC. Product and safety info Important: For important info on the safe use of your device and battery, read the Product and safety info booklet before you take your device into use. You can only use your device on the GSM 850, 900, 1800, 1900;

WCDMA 1, 2, 4, 5, 8; LTE 1, 2, 3, 4, 5, 7, 8, 12, 13, 17, 28, 40, 66, networks. You need a subscription with a service provider. Important: 4G/LTE might not be supported by your network service provider or by the service provider you are using when traveling. In these cases, you may not be able to make or receive calls, send or receive messages or use mobile data connections. To make sure your device works seamlessly when full 4G/LTE service is not available, it is recommended that you change the highest connection speed from 4G to 3G. To do this, on the home screen, tap Settings > Network & Internet > Mobile network > Advanced, and switch Preferred network type to 3G. For more info, contact your network service provider. Your device has an internal, non-removable, rechargeable battery. Do not attempt to remove the battery or back cover, as you may damage the device. To replace the battery, take the device to the nearest authorised service facility. Charge your device with the AD-010E, CH-21E, A829EU, AD-020E (EU plug) / AD-010X, CH-21X, A829UK, AD-020X (UK plug) / AD-010U, CH-21U, PA-US5V2A-036, A829US, AD-020U (US plug) / AD-010A, CH-21A (Australia plug), AD-010B, CH-21B (Brazil plug) / UT-580I-

5200Z2Y, CH-21N (India plug) chargers. HMD Global may make additional battery or charger models available for this device. Charging time can vary depending on device capability. Some of the accessories mentioned in this user guide, such as charger, headset, or data cable, may be sold separately. Electrical Information of the Charger The following electrical information corresponds to the above-

mentioned charger models:

Input: 100-240V, 50/60Hz, 0,35 A (AD-010U), 0,3 A (CH-21U), 0,5 A

(PA-US5V2A-036, A829US) Output: 5 Vcc; 2,0 A (AD-010U, CH-21U, PA-US5V2A-036), 5V/3A, 9V/

2,23A, 12V/1,67A (A829US) Charger safety instructions The charger is suitable to be used only with compatible devices. The charger should not be used in extremely high or low temperatures. Ventilation should not be obstructed by covering the charger with magazines, blankets, curtains etc. Open flames, such as candles, should not be placed above the charger. The charger and the wall outlet shall be easily accessible at all times. In case the cable or the plugs are damaged, stop using them. The charger requires very low maintenance. If you want to clean it, use a dry cloth or a brush. Meaning of the symbols:

For internal use only The charger should not be disposed as unsorted municipal waste. It should be recycled. The surface of the device is nickel-free. Parts of the device are magnetic. Metallic materials may be attracted to the device. Do not place credit cards or other magnetic stripe cards near the device for extended periods of time, since the cards may be damaged. Note: Pre-installed system software and apps use a significant part of memory space. Keep a safe distance when using the flash. Do not use the flash on people or animals at close range. Do not cover the flash while taking a photo. Certification information (SAR) This mobile device meets guidelines for exposure to radio waves as set forth by the Federal Communications Commission (FCC). Refer to the following. FCC RF Exposure Information Your handset is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The guidelines are based on standards that were developed by independent scientific organization through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless handsets employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1,6 W/kg. The tests are performed in positions and locations (e.g. at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this handset model as reported to the FCC when tested for use at the ear is 1,00 W/kg, and when worn on the body in a holder or carry case, is 1,10 W/kg. Body-worn Operation; This device was tested for typical body-worn operations with the handset kept 1,0 cm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 1,0 cm separation distance between the users body and the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of

Designed by HMO Global Oy Bertel Jungin aukio 9 02600 Espoo Finland Model TA-112 FCC ID: 2AJOTTAMI&12 Made in China ps4

HMD Global Oy Bertel Jungin aukio 9, 02600 Espoo, Finland C2PC Declaration letter Date: November 7, 2022 To whom it may concern, We, HMD Global Oy, hereby declare that we are only and fully responsible for this CIIPC application of FCC ID: 2AJOTTA-1412, originally granted on 12/30/2021. Now we would like to modify the authorized equipment for below changes:

1. Change packaging factory of the main chip UMS9230 ( new SoC with new packaging material) 2. Removed Aohai_A829US adapter, BRL_ CB - 36A USB cable, Saibao_ CB - 12A USB cable, LEADER_ HS-34 earphone 3. Added Saibao_AC-2A USB Cable 4. The software version is changed to 00WW_1_520, RF performance is exactly same with the previous version. Sincerely yours, _________________________________ Contact Person: Reza Serafat Email: reza.serafat@hmdglobal.com

HMD Global Oy Bertel Jungin aukio 9, 02600 Espoo, Finland Power of Attorney Date: October 21, 2022 To whom it may concern, Please be notified that I, Reza Serafat, have designated Joey Lao in BV 7Layers Communications Technology (Shenzhen) Co.,Ltd as the person being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Joey Lao in BV 7Layers Communications Technology (Shenzhen) Co.,Ltd on the matters of relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. We further certifies that neither the applicant nor any party to this application, as defined in 47 CFR Ch. 1.2002 (b), is subject to a denial to Federal benefits, that include FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C 862. This authorization is limited to the product of as following:

FCC ID: 2AJOTTA-1412 If you have any acknowledgement and response, please send it to BV 7Layers Communications Technology (Shenzhen) Co., Ltd directly. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely yours, ____ Contact Person: Reza Serafat E-mail: reza.serafat@hmdglobal.com

HMD Global Oy Bertel Jungin aukio 9, 02600 Espoo, Finland Federal Communications Commission 7435 Oakland Mills Road - Gate A Columbia, Maryland 21046 Subject: Request for Confidentiality FCC ID: 2AJOTTA-1412 To Whom It May Concern, Date: October 21, 2022 Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. N/A Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission s policy, in order to comply with the marketing regulations in 47 CFT 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days after the Grant Date of Equipment Authorizations. External Photos Internal Photos Test Setup Photos It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, Signature: _______ Contact Person: Reza Serafat E-mail: reza.serafat@hmdglobal.com

HMD Global Oy Bertel Jungin aukio 9, 02600 Espoo, Finland UNII Declaration Letter We have declared below featured for FCC equipment authorization, device FCC ID: 2AJOTTA-1412

(1) DFS Device --

Master, Client without radar detection capability, Client with Radar detection capability , N/A

(2) Active / Passive Scanning , adhoc mode access point capability Frequency Band

(MHz) Active Scanning

(the device can transmit a probe

(beacon)) 2412 2462 MHz 5150 5250 MHz 5250 5350 MHz 5470 5725 MHz 5725 5850 MHz Yes, Yes, Yes, Yes, Yes, No No No No No passive scanning

(where the device is can listen only with no probes) Yes, Yes, Yes, Yes, Yes, No No No No No Ad Hoc Mode capability Access point capability Yes, Yes, Yes, Yes, Yes, No No No No No Yes, Yes, Yes, Yes, Yes, No No No No No

(3) Country code selection ability -

If no, pls explain how was implemented : use Microsoft network utility Yes , No

(4) Meet 15.202 requirement -

pls check below :

Yes , No , A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network.

(5) For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes can not be modified by end user or an installer. Apply , No Apply

(If apply , pls help to provide explanation on how it was implement (By hardware or software , and how software was controlled) The active or passive mode was controlled by software. For non-DFS frequency used active scanning, for DFS frequency was switched to passive scanning by software Mechanism If you have any questions, please feel free to contact me at the address shown below. Yours sincerely, Signatory Contact Person: Reza Serafat E-mail: reza.serafat@hmdglobal.com

HMD Global Oy Bertel Jungin aukio 9, 02600 Espoo, Finland Date: October 21, 2022 We, HMD Global Oy, declare that this EUT (FCC ID: 2AJOTTA-1412) doesn't have Ad Hoc Mode function on "non-US frequencies". In addition, the frequency selection feature is disabled by firmware for devices marketed to the US. For DTS part of this device, only channels 1~11 will be used in North America. Country code selection is disabled. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely yours, ____ Contact Person: Reza Serafat E-mail: reza.serafat@hmdglobal.com

HMD Global Oy Bertel Jungin aukio 9 02600 Espoo, Finland Tel +358 86 4213499 Fax +358 45 2133756 Federal Communications Commission Authorization & Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: CHANGE IN IDENTIFICATION OF EQUIPMENT Dear Sir or Madam:

We, HMD Global Oy hereby request a new FCC ID as established in 47CFR2.933(b) for a currently approved device. This request is to establish the new FCC ID: 2AJOTTA-1412. Original FCC ID: 2AJOTTA-1404 Original Model: TA-1404 Original Grant Date: 12/24/2021 New FCC ID: 2AJOTTA-1412 Model: TA-1412 Brand(s): NOKIA The equipment is the identical design and construction with only difference on the SIM adapter and color, TA-1404 support Double SIM, while TA-1412 can support Single SIM, to the original FCC Grant cited above. 1. The original test reports will to be representative of and applicable to the equipment bearing the changed identification If you have any questions, please contact Reza Serafat via phone +491735287964 or email at reza.serafat@hmdglobal.com Sincerely, print name: Reza Serafat Signature:

HMD Global Oy is the exclusive licensee of the Nokia brand for phones & tablets. Nokia is a registered trademark of the Nokia Corporation.