FCC ID: MCLWINA2 WiFi 11 b/g/n module

WIN-A2 WIFI Module User Manual Rev. 0.01 Confidential 1 Department Name Hardware Engineering GaoJian Review Dates Plan Results Confidential 2 1. Introduction Project Name: 802.11b/g/n WIFI module. This documentation describes the product specification of the WIFI 802.11b/g/n module, it is a confidential document of FOXCONN. 1.1 Scope The device provide communications for applications operating in the globally available 2.4GHz unlicensed ISM band, which utilizing direct sequence spread spectrum and OFDM/CCK technology, the maximum data rate can reach to 65 Mbps(MCS7) for HT20. 1.2 Function Support single-band IEEE 802.11b/g and handheld device class 802.11n. 1x1 single stream with antenna diversity. SDIO v2.0 4bit mode interface support. Full support for power saving modes. Confidential 3 2. Product Specification 2.1 Output Center And Symbol Clock Frequency Tolerance Center frequency tolerance CH1/CH7/CH13 Spec. (ppm)

+/-25 2.2 RF Specification 2.2.1 Spectrum Mask spec Mode of Operation 802.11g 802.11 g at r 9 MHz Offset 802.11 g at r 11 MHz Offset 802.11 g at r 20 MHz Offset 802.11 g at r 30 MHz Offset Mode of Operation 802.11b 802.11b at +/-11MHz~+/-22MHz Offset 802.11b at >+22MHz,<-22MHz Offset Mode of Operation 802.11n-HT20 802.11n at r9 MHz offset 802.11n at r11 MHz offset 802.11n at r20 MHz offset 802.11n at r30 MHz offset Specifications 0 dBr

-20 dBr

-28 dBr

-40 dBr Specifications

-30 dBr

-50 dBr Specifications 0 dBr

-20 dBr

-28 dBr

-45 dBr Confidential 4 2.3 Electrical Specification 2.3.1 Absolute Maximum Ratings The specification indicates levels where permanent damage to the device can occur. Functional operation is not guaranteed under these conditions. Operation at absolute maximum conditions for extended can adversely affect long-term reliability of the device. Rating Symbol DC supply voltage for the device VDD Value

-0.5~6 Unit V 2.3.2 Recommended operating condition Parameter DC Supply Voltage Minimum 3 Typical 3.3 Maximum 3.6 Unit

[v]

2.3.3 Current consumption in active on WLAN modes Confidential 5 3. Mechanical Drawing Confidential 6 4. Regulatory Information USA-Federal Communications Commission (FCC) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Labeling Hon Hai Precision WiFi 11b/g/n module WIN-A2 labeled as below. FCC ID: MCLWINA2 The proposed with FCC ID label format is to be placed on the module. If FCC ID is not visible when the module is installed into the system, Contains FCC ID: MCLWINA2 shall be placed on the outside of final host system. Caution: Exposure to Radio Frequency Radiation. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Confidential 7 Canada-Industry Canada (IC) This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause undesired operation of this device. The term IC before the equipment certification number only signifies that the Industry Canada technical specifications were met. Caution: Exposure to Radio Frequency Radiation. To comply with IC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and allpersons. This device must not be co-located or operating in conjunction with anyother antenna or transmitter. Confidential 8

FCC ID: MCLWINA2 IC: 2878D-WINA2 Label & Label Location XXXXXXXX XXXXX X

PUTER eae

[Al Foxca he Fae a Coe Date: October 12, 2010 Compliance Certification Services COcuitelerrnley mM DInaClest 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern:

I, the undersigned, hereby authorize Ms. Claire Hoque/Application Examiner of Compliance Engineering Services, Inc., d.b.a. Compliance Certification Services and hereafter referred to as UL CCS, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Ms. Claire Hoque of UL CCS on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. PetCo In authorizing UL CCS as our agent, we still recognize that we are responsible to:

EY] comply with the relevant provisions of the certification program;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which certification has been granted;

do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

Creer eet R Cee IESE]

[Al Foxconn: Network System Group use certification only to indicate the products are certified as being in conformity ABU O ORI LTICE Teele endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

kK) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerelv Yours. OPM Rio Chen, Compliance Manager Hon Hai Precision Ind. Co., Ltd. PFN This authorization letter will be sent along with your application when filing with the Certification Division. Please follow the format and type it on company letterhead and send original to us. Authorized signature must be in agreement with grantee code contact in FCC database.

Applicant/Grantee Hon Hai Precision Ind. Co.,Ltd. FCC ID:

MCLWINA2 Request for Modular Approval Request for Limited Modular Approval Requirements EUT Conditions Section 15.212 Modular Transmitters Single Modular Approval Requirements Comply

(Y/N) Y Y Y Y Y The device is equipped with Metal shielding to cover RF section. Refer to external photos All inputs to the device are buffered through logic U1 inputs. Refer to Schematic Diagram. The device is equipped with Internal 1.8VDC regulator. Refer to Block Diagram. Device is equipped with unique antenna (part number: KK23017-

01-7F,verdor: FOXCONN.) The device was tested outside of the Desktop PC for full modular approval. Refer to setup photos. 1 2 3 4 5 The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-

modulation. The modular transmitter must have its own power supply regulation. The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)). 6 7 8 The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number.

(A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: XYZMODEL1 or Contains FCC ID:

XYZMODEL1. Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization.

(B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following:

Contains FCC certified transmitter module(s). Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. Y The proposed FCC ID label format is to be placed on the module. If FCC ID is not visible when the module is installed into the system, Contains FCC ID: MCLWINA2 shall be placed on the outside of final host system. Refer to Users Guide Exhibit Y The device complies with RF exposure compliance requirement Y A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured.

HON HAI PRECISION IND. CO., LTD. HSINCHU SCIENCE PARK BRANCH OFFICE MIN SHENG PLANT 5F-1, 5 Hsin-An Road 4-1 Ming-Sheng St., Hsinchu, Science-Based Industrial Park Tu-Cheng Industrila Area, Taiwan, R.O.C. Taiwan, R.O.C TEL:+886-3-5784975 TEL:+886-2-2267 6511 FAX:+886-3-5775100 FAX:+886-2-2267 6512 Request for Confidentiality Date: March 2, 2011 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject:

FCC ID: MCLWINA2 To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Antenna Specification Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, Rio Chen, Compliance Manager Hon Hai Precision Ind. Co., Ltd.

FCC CFR47 PART 15 SUBPART C INDUSTRY CANADA RSS-210 ISSUE 8 CERTIFICATION TEST REPORT FOR WIFI 11b/g/n MODULE MODEL NUMBER: WIN-A2 FCC ID: MCLWINA2 IC: 2878D-WINA2 REPORT NUMBER: 11J13629-1 ISSUE DATE: FEBRUARY 9, 2011 Prepared for HON HAI PRECISION IND. CO., LTD. 5F-1, 5 HSIN-AN ROAD HSINCHU SCIENCE-BASED INDUSTRIAL PARK COMPLIANCE CERTIFICATION SERVICES (UL CCS) TAIWAN, R.O.C. Prepared by 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 Revision History Rev.

---

Issue Date 02/09/2011 Revisions Initial Issue Revised By T. Chan COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 2 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 TABLE OF CONTENTS DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 1. ATTESTATION OF TEST RESULTS....................................................................................5 2. TEST METHODOLOGY ........................................................................................................6 3. FACILITIES AND ACCREDITATION....................................................................................6 4. CALIBRATION AND UNCERTAINTY ..................................................................................6 4.1. MEASURING INSTRUMENT CALIBRATION ...............................................................6 4.2. SAMPLE CALCULATION..............................................................................................6 4.3. MEASUREMENT UNCERTAINTY................................................................................6 5. EQUIPMENT UNDER TEST .................................................................................................7 5.1. DESCRIPTION OF EUT................................................................................................7 5.2. MAXIMUM OUTPUT POWER.......................................................................................7 5.3. DESCRIPTION OF AVAILABLE ANTENNAS...............................................................7 5.4. SOFTWARE AND FIRMWARE.....................................................................................7 5.5. WORST-CASE CONFIGURATION AND MODE ..........................................................7 5.6. DESCRIPTION OF TEST SETUP.................................................................................8 6. TEST AND MEASUREMENT EQUIPMENT .......................................................................10 7.2. 7.1. 7.1.1. 7.1.2. 7.1.3. 7.1.4. 7.1.5. 7.1.6. 7. ANTENNA PORT TEST RESULTS ....................................................................................11 802.11b MODE IN THE 2.4 GHz BAND......................................................................11 6 dB BANDWIDTH ..............................................................................................11 99% BANDWIDTH ..............................................................................................14 OUTPUT POWER ...............................................................................................17 AVERAGE POWER ............................................................................................18 POWER SPECTRAL DENSITY ..........................................................................19 CONDUCTED SPURIOUS EMISSIONS.............................................................22 802.11g MODE IN THE 2.4 GHz BAND......................................................................26 6 dB BANDWIDTH ..............................................................................................26 99% BANDWIDTH ..............................................................................................29 OUTPUT POWER ...............................................................................................32 AVERAGE POWER ............................................................................................33 POWER SPECTRAL DENSITY ..........................................................................34 CONDUCTED SPURIOUS EMISSIONS.............................................................37 802.11n HT20 SISO MODE IN THE 2.4 GHz BAND ..................................................41 6 dB BANDWIDTH ..............................................................................................41 99% BANDWIDTH ..............................................................................................44 OUTPUT POWER ...............................................................................................47 AVERAGE POWER ............................................................................................48 POWER SPECTRAL DENSITY ..........................................................................49 CONDUCTED SPURIOUS EMISSIONS.............................................................52 7.2.1. 7.2.2. 7.2.3. 7.2.4. 7.2.5. 7.2.6. 7.3.1. 7.3.2. 7.3.3. 7.3.4. 7.3.5. 7.3.6. 7.3. 8. RADIATED TEST RESULTS ..............................................................................................56 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 3 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. 8.1. 8.2. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 LIMITS AND PROCEDURE ........................................................................................56 TRANSMITTER ABOVE 1 GHz ..................................................................................57 802.11b MODE IN THE 2.4 GHz BAND..............................................................57 802.11g MODE IN THE 2.4 GHz BAND..............................................................62 802.11n HT20 SISO MODE IN THE 2.4 GHz BAND ..........................................68 8.3. WORST CASE RECEIVER ABOVE 1 GHz ................................................................73 8.4. WORST CASE BELOW 1GHZ....................................................................................74 8.2.1. 8.2.2. 8.2.3. 9. AC POWER LINE CONDUCTED EMISSIONS...................................................................75 10. MAXIMUM PERMISSIBLE EXPOSURE ........................................................................79 SETUP PHOTOS ............................................................................................................82 11. COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 4 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 1. ATTESTATION OF TEST RESULTS COMPANY NAME:

HON HAI PRECISION IND. CO., LTD. 5F-1, 5 HSIN-AN ROAD HSINCHU SCIENCE-BASED INDUSTRIAL PARK TAIWAN, R.O.C. EUT DESCRIPTION:

MODEL:

SERIAL NUMBER:

DATE TESTED:

WIFI 11B/G/N MODULE WIN-A2 A4C0E127283 FEBRUAR 3-8, 2011 APPLICABLE STANDARDS STANDARD CFR 47 Part 15 Subpart C INDUSTRY CANADA RSS-210 Issue 8 Annex 8 INDUSTRY CANADA RSS-GEN Issue 3 TEST RESULTS Pass Pass Pass Compliance Certification Services (UL CCS) tested the above equipment in accordance with the requirements set forth in the above standards. All indications of Pass/Fail in this report are opinions expressed by UL CCS based on interpretations and/or observations of test results. Measurement Uncertainties were not taken into account and are published for informational purposes only. The test results show that the equipment tested is capable of demonstrating compliance with the requirements as documented in this report. Note: The results documented in this report apply only to the tested sample, under the conditions and modes of operation as described herein. This document may not be altered or revised in any way unless done so by UL CCS and all revisions are duly noted in the revisions section. Any alteration of this document not carried out by UL CCS will constitute fraud and shall nullify the document. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, any agency of the Federal Government, or any agency of any government. Approved & Released For UL CCS By:

Tested By:

THU CHAN ENGINEERING MANAGER UL CCS CHIN PANG EMC ENGINEER UL CCS COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 5 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 2. TEST METHODOLOGY The tests documented in this report were performed in accordance with ANSI C63.10-2009, FCC CFR 47 Part 2, FCC CFR 47 Part 15, RSS-GEN Issue 3, and RSS-210 Issue 8. 3. FACILITIES AND ACCREDITATION The test sites and measurement facilities used to collect data are located at 47173 Benicia Street, Fremont, California, USA. UL CCS is accredited by NVLAP, Laboratory Code 200065-0. The full scope of accreditation can be viewed at http://www.ccsemc.com. 4. CALIBRATION AND UNCERTAINTY 4.1. MEASURING INSTRUMENT CALIBRATION The measuring equipment utilized to perform the tests documented in this report has been calibrated in accordance with the manufacturer's recommendations, and is traceable to recognized national standards. 4.2. SAMPLE CALCULATION Where relevant, the following sample calculation is provided:

Field Strength (dBuV/m) = Measured Voltage (dBuV) + Antenna Factor (dB/m) +

Cable Loss (dB) Preamp Gain (dB) 36.5 dBuV + 18.7 dB/m + 0.6 dB 26.9 dB = 28.9 dBuV/m 4.3. MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the apparatus:

PARAMETER UNCERTAINTY Conducted Disturbance, 0.15 to 30 MHz Radiated Disturbance, 30 to 1000 MHz 3.52 dB 4.94 dB Uncertainty figures are valid to a confidence level of 95%. COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 6 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 5. EQUIPMENT UNDER TEST 5.1. DESCRIPTION OF EUT The EUT is WIFI Module with 802.11B/G/HT20. The radio module is manufactured by Hon Hai Precision. 5.2. MAXIMUM OUTPUT POWER The transmitter has a maximum peak conducted output power as follows:

Frequency Range Mode Output Power Output Power

(MHz) 2412 - 2462 2412 - 2462 2412 - 2462 802.11b 802.11g 802.11n HT20 SISO

(dBm) 18.30 24.20 24.00

(mW) 67.61 263.03 251.19 5.3. DESCRIPTION OF AVAILABLE ANTENNAS The radio utilizes a PiFA antenna for TX/RX diversity, with maximum peak gains of 2.05dBi 5.4. SOFTWARE AND FIRMWARE The EUT test utility software installed in the host computer during testing was Broadcom test program BCM43362SDGN6L version 5.90.104 WLTEST 5.5. WORST-CASE CONFIGURATION AND MODE The worst-case data rate for each mode is determined to be as follows, based on preliminary tests of the chipset utilized in this radio. All final tests in the 802.11b mode were made at 1 Mb/s. All final tests in the 802.11g mode were made at 6 Mb/s. All final tests in the 802.11n HT20 SISO mode were made at MCS0. For radiated emissions below 1 GHz the worst-case configuration is determined to be the mode and channel with the highest output power To determine the worst-position of highest emissions, the EUTs antenna was investigated for X, Y, Z positions, and the worst position was turned out to be a Y-position with long ends at left side. COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 7 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 5.6. DESCRIPTION OF TEST SETUP SUPPORT EQUIPMENT DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 PERIPHERAL SUPPORT EQUIPMENT LIST Manufacturer V-Infinity Dell Dell Broadcom Model HK-C113-A05 PP09S LA65NSO-00 BCM95ANAD Serial Number NA 27920070721 CN-ODF263-71615-775-605A 1395274 FCC ID DoC DoC DoC NA

# of Identical Ports 2 2 1 Connector Type I/O CABLE LIST Cable Type US 115V US 115V 19 pin Ribon Un-shielded Un-shielded Un-shielded Cable Length 2m 2m 0.4m Remarks No No Yes Description AC Adapter Laptop AC Adapter Interface Card I/O CABLES Port AC DC SDN Cable No. 1 2 3 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 8 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 SETUP DIAGRAM DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 Interface Card EUT 2 3 Laptop 2 AC Adapter AC Adapter 1 1 115VAC 60Hz TEST SETUP The EUT is connected to a Laptop via an interface card during the test. COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 9 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 6. TEST AND MEASUREMENT EQUIPMENT The following test and measurement equipment was utilized for the tests documented in this report:

TEST EQUIPMENT LIST Manufacturer Agilent / HP Agilent / HP EMCO Sunol Sciences FCC R & S Micro-Tronics Agilent / HP Boonton Boonton Model 8447D 8449B 3115 JB1 LISN-50/250-25-2 ESHS 20 BRM50702 E4440A 4541 57318 Asset C00885 C01052 C00945 C01016 N02625 N02396 N02685 C01178 C01186 C01202 Cal Due 01/26/12 07/14/11 06/29/11 07/12/11 11/10/11 05/06/11 CNR 08/30/11 03/01/11 02/23/11 Description Preamplifier, 1300 MHz Preamplifier, 26.5 GHz Antenna, Horn, 18 GHz Antenna, Bilog, 2 GHz LISN, 30 MHz EMI Test Receiver, 30 MHz Reject Filter, 2.4-2.5 GHz Spectrum Analyzer, 26.5 GHz Peak Power Meter Peak Power Sensor COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 10 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 7. ANTENNA PORT TEST RESULTS 7.1. 802.11b MODE IN THE 2.4 GHz BAND 7.1.1. 6 dB BANDWIDTH LIMITS FCC 15.247 (a) (2) IC RSS-210 A8.2 (a) The minimum 6 dB bandwidth shall be at least 500 kHz. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The RBW is set to 100 kHz and the VBW is set to 300 kHz. The sweep time is coupled. Channel Frequency 6 dB Bandwidth Minimum Limit

(MHz) 2412 2437 2462

(MHz) 8.00 8.00 8.03

(MHz) 0.5 0.5 0.5 Low Middle High RESULTS COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 11 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 6 dB BANDWIDTH 6 dB BANDWIDTH LOW CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 6 dB BANDWIDTH MID CH COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 12 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 6 dB BANDWIDTH HIGH CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 13 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 7.1.2. 99% BANDWIDTH LIMITS None; for reporting purposes only. DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 TEST PROCEDURE The transmitter output is connected to the spectrum analyzer. The RBW is set to 1% to 3% of the 99 % bandwidth. The VBW is set to 3 times the RBW. The sweep time is coupled. The spectrum analyzer internal 99% bandwidth function is utilized. RESULTS Channel Low Middle High Frequency 99% Bandwidth

(MHz) 2412 2437 2462

(MHz) 12.4133 12.5266 12.3380 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 14 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 99% BANDWIDTH 99% BANDWIDTH LOW CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 99% BANDWIDTH MID CH COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 15 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 99% BANDWIDTH HIGH CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 16 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 7.1.3. OUTPUT POWER DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 LIMITS FCC 15.247 (b) IC RSS-210 A8.4 The maximum antenna gain is less than or equal to 6 dBi, therefore the limit is 30 dBm. TEST PROCEDURE The transmitter output is connected to a power meter. RESULTS Channel Frequency Low Middle High

(MHz) 2412 2437 2462 Output Power

(dBm) 18.20 18.30 18.20 Limit Margin

(dBm) 30 30 30

(dB)

-11.80

-11.70

-11.80 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 17 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 REPORT NO: 11J13629-1 FCC ID: MCLWINA2 7.1.4. AVERAGE POWER LIMITS None; for reporting purposes only. TEST PROCEDURE The transmitter output is connected to a power meter. RESULTS The cable assembly insertion loss of 11dB (including 10 dB pad and 1dB cable) was entered as an offset in the power meter to allow for direct reading of power. Channel Frequency Low Middle High

(MHz) 2412 2437 2462 Power

(dBm) 16.10 16.10 16.00 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 18 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 7.1.5. POWER SPECTRAL DENSITY DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 LIMITS FCC 15.247 (e) IC RSS-210 A8.2 (b) The power spectral density conducted from the transmitter to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. TEST PROCEDURE Output power was measured based on the use of a peak measurement, therefore the power spectral density was measured using PSD Option 1 in accordance with FCC document Measurement of Digital Transmission Systems Operating under Section 15.247, March 23, 2005. RESULTS Channel Low Middle High Frequency

(MHz) 2412 2437 2462 PPSD

(dBm)

-2.66

-2.68

-2.81 Limit

(dBm) 8 8 8 Margin

(dB)

-10.66

-10.68

-10.81 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 19 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 POWER SPECTRAL DENSITY PSD LOW CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 PSD MID CH COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 20 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 PSD HIGH CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 21 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 7.1.6. CONDUCTED SPURIOUS EMISSIONS LIMITS FCC 15.247 (d) IC RSS-210 A8.5 Output power was measured based on the use of a peak measurement, therefore the required attenuation is 20 dB. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The resolution bandwidth is set to 100 kHz. The video bandwidth is set to 300 kHz. The spectrum from 30 MHz to 26 GHz is investigated with the transmitter set to the lowest, middle, and highest channels. COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 22 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 RESULTS SPURIOUS EMISSIONS, LOW CHANNEL LOW CH BANDEDGE DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 LOW CH SPURIOUS COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 23 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 SPURIOUS EMISSIONS, MID CHANNEL MID CH REFERENCE DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 MID CH SPURIOUS COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 24 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 SPURIOUS EMISSIONS, HIGH CHANNEL HIGH CH BANDEDGE DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 HIGH CH SPURIOUS COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 25 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 7.2. 802.11g MODE IN THE 2.4 GHz BAND DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 7.2.1. 6 dB BANDWIDTH LIMITS FCC 15.247 (a) (2) IC RSS-210 A8.2 (a) The minimum 6 dB bandwidth shall be at least 500 kHz. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The RBW is set to 100 kHz and the VBW is set to 300 kHz. The sweep time is coupled. RESULTS Channel Low Middle High Frequency 6 dB Bandwidth Minimum Limit

(MHz) 2412 2437 2462

(MHz) 15.03 15.00 15.00

(MHz) 0.5 0.5 0.5 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 26 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 6 dB BANDWIDTH 6 dB BANDWIDTH LOW CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 6 dB BANDWIDTH MID CH COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 27 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 6 dB BANDWIDTH HIGH CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 28 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 7.2.2. 99% BANDWIDTH LIMITS None; for reporting purposes only. DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 TEST PROCEDURE The transmitter output is connected to the spectrum analyzer. The RBW is set to 1% to 3% of the 99 % bandwidth. The VBW is set to 3 times the RBW. The sweep time is coupled. The spectrum analyzer internal 99% bandwidth function is utilized. RESULTS Channel Low Middle High Frequency 99% Bandwidth

(MHz) 2412 2437 2462

(MHz) 16.3107 16.3240 16.2325 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 29 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 99% BANDWIDTH 99% BANDWIDTH LOW CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 99% BANDWIDTH MID CH COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 30 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 99% BANDWIDTH HIGH CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 31 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 7.2.3. OUTPUT POWER DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 LIMITS FCC 15.247 (b) IC RSS-210 A8.4 The maximum antenna gain is less than or equal to 6 dBi, therefore the limit is 30 dBm. z TEST PROCEDURE The transmitter output is connected to a power meter. RESULTS Channel Frequency

(MHz) 2412 2437 2462 Low Middle High Output Power

(dBm) 24.10 24.20 24.00 Limit Margin

(dBm) 30 30 30

(dB)

-5.90

-5.80

-6.00 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 32 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 REPORT NO: 11J13629-1 FCC ID: MCLWINA2 7.2.4. AVERAGE POWER LIMITS None; for reporting purposes only. TEST PROCEDURE The transmitter output is connected to a power meter. RESULTS The cable assembly insertion loss of 11 dB (including 10 dB pad and 1 dB cable) was entered as an offset in the power meter to allow for direct reading of power. Channel Frequency Low Middle High

(MHz) 2412 2437 2462 Power

(dBm) 15.10 15.30 15.20 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 33 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 7.2.5. POWER SPECTRAL DENSITY LIMITS FCC 15.247 (e) IC RSS-210 A8.2 (b) The power spectral density conducted from the transmitter to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. TEST PROCEDURE Output power was measured based on the use of a peak measurement, therefore the power spectral density was measured using PSD Option 1 in accordance with FCC document Measurement of Digital Transmission Systems Operating under Section 15.247, March 23, 2005. RESULTS Channel Low Middle High Frequency

(MHz) 2412 2437 2462 PPSD

(dBm)

-7.44

-7.32

-6.88 Limit

(dBm) 8 8 8 Margin

(dB)

-15.44

-15.32

-14.88 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 34 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 POWER SPECTRAL DENSITY PSD LOW CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 PSD MID CH COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 35 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 PSD HIGH CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 36 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 7.2.6. CONDUCTED SPURIOUS EMISSIONS LIMITS FCC 15.247 (d) IC RSS-210 A8.5 Output power was measured based on the use of a peak measurement, therefore the required attenuation is 20 dB. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The resolution bandwidth is set to 100 kHz. The video bandwidth is set to 300 kHz. The spectrum from 30 MHz to 26 GHz is investigated with the transmitter set to the lowest, middle, and highest channels. COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 37 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 RESULTS SPURIOUS EMISSIONS, LOW CHANNEL LOW CH BANDEDGE DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 LOW CH SPURIOUS COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 38 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 SPURIOUS EMISSIONS, MID CHANNEL MID CH REFERENCE DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 MID CH SPURIOUS COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 39 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 SPURIOUS EMISSIONS, HIGH CHANNEL HIGH CH BANDEDGE DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 HIGH CH SPURIOUS COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 40 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 7.3. 802.11n HT20 SISO MODE IN THE 2.4 GHz BAND 7.3.1. 6 dB BANDWIDTH LIMITS FCC 15.247 (a) (2) IC RSS-210 A8.2 (a) The minimum 6 dB bandwidth shall be at least 500 kHz. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The RBW is set to 100 kHz and the VBW is set to 300 kHz. The sweep time is coupled. RESULTS Channel Low Middle High Frequency 6 dB Bandw idth Minimum Limit

(MHz) 2412 2437 2462

(MHz) 15.05 14.95 15.00

(MHz) 0.5 0.5 0.5 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 41 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 6 dB BANDWIDTH 6 dB BANDWIDTH LOW CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 6 dB BANDWIDTH MID CH COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 42 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 6 dB BANDWIDTH HIGH CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 43 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 7.3.2. 99% BANDWIDTH LIMITS None; for reporting purposes only. DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 TEST PROCEDURE The transmitter output is connected to the spectrum analyzer. The RBW is set to 1% to 3% of the 99 % bandwidth. The VBW is set to 3 times the RBW. The sweep time is coupled. The spectrum analyzer internal 99% bandwidth function is utilized. RESULTS Channel Low Middle High Frequency 99% Bandwidth

(MHz) 2412 2437 2462

(MHz) 16.3681 16.4601 16.3586 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 44 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 99% BANDWIDTH 99% BANDWIDTH LOW CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 99% BANDWIDTH MID CH COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 45 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 99% BANDWIDTH HIGH CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 46 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 7.3.3. OUTPUT POWER DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 LIMITS FCC 15.247 (b) IC RSS-210 A8.4 The maximum antenna gain is less than or equal to 6 dBi, therefore the limit is 30 dBm. TEST PROCEDURE The transmitter output is connected to a power meter. RESULTS Channel Frequency

(MHz) 2412 2437 2462 Low Middle High Output Power

(dBm) 23.90 24.00 23.80 Limit

(dBm) 30 30 30 Margin

(dB)

-6.10

-6.00

-6.20 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 47 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 REPORT NO: 11J13629-1 FCC ID: MCLWINA2 7.3.4. AVERAGE POWER LIMITS None; for reporting purposes only. TEST PROCEDURE The transmitter output is connected to a power meter. RESULTS The cable assembly insertion loss of 11 dB (including 10 dB pad and 1.0 dB cable) was entered as an offset in the power meter to allow for direct reading of power. Channel Frequency Low Middle High

(MHz) 2412 2437 2462 Power

(dBm) 14.60 14.70 14.50 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 48 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 7.3.5. POWER SPECTRAL DENSITY LIMITS FCC 15.247 (e) IC RSS-210 A8.2 (b) The power spectral density conducted from the transmitter to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. TEST PROCEDURE Output power was measured based on the use of a peak measurement, therefore the power spectral density was measured using PSD Option 1 in accordance with FCC document Measurement of Digital Transmission Systems Operating under Section 15.247, March 23, 2005. RESULTS Channel Low Middle High Frequency

(MHz) 2412 2437 2462 PPSD

(dBm)

-5.33

-5.29

-5.66 Limit

(dBm) 8 8 8 Margin

(dB)

-13.33

-13.29

-13.66 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 49 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 POWER SPECTRAL DENSITY PSD LOW CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 PSD MID CH COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 50 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 PSD HIGH CH DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 51 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 7.3.6. CONDUCTED SPURIOUS EMISSIONS LIMITS FCC 15.247 (d) IC RSS-210 A8.5 Output power was measured based on the use of a peak measurement, therefore the required attenuation is 20 dB. TEST PROCEDURE The transmitter output is connected to a spectrum analyzer. The resolution bandwidth is set to 100 kHz. The video bandwidth is set to 300 kHz. The spectrum from 30 MHz to 26 GHz is investigated with the transmitter set to the lowest, middle, and highest channels. COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 52 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 RESULTS SPURIOUS EMISSIONS, LOW CHANNEL LOW CH BANDEDGE DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 LOW CH SPURIOUS COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 53 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 SPURIOUS EMISSIONS, MID CHANNEL MID CH REFERENCE DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 MID CH SPURIOUS COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 54 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 SPURIOUS EMISSIONS, HIGH CHANNEL HIGH CH BANDEDGE DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 HIGH CH SPURIOUS COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 55 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 8. RADIATED TEST RESULTS 8.1. LIMITS AND PROCEDURE LIMITS FCC 15.205 and 15.209 IC RSS-210 Clause 2.6 (Transmitter) IC RSS-GEN Clause 6 (Receiver) Frequency Range

(MHz) 30 - 88 88 - 216 216 - 960 Above 960 Field Strength Limit

(uV/m) at 3 m 100 150 200 500 Field Strength Limit

(dBuV/m) at 3 m 40 43.5 46 54 TEST PROCEDURE The EUT is placed on a non-conducting table 80 cm above the ground plane. The antenna to EUT distance is 3 meters. The EUT is configured in accordance with ANSI C63.4. The EUT is set to transmit in a continuous mode. For measurements below 1 GHz the resolution bandwidth is set to 100 kHz for peak detection measurements or 120 kHz for quasi-peak detection measurements. Peak detection is used unless otherwise noted as quasi-peak. For measurements above 1 GHz the resolution bandwidth is set to 1 MHz, and then the video bandwidth is set to 1 MHz for peak measurements and 10 Hz for average measurements. The spectrum from 30 MHz to 26 GHz is investigated with the transmitter set to the lowest, middle, and highest channels in the 2.4 GHz band. The frequency range of interest is monitored at a fixed antenna height and EUT azimuth. The EUT is rotated through 360 degrees to maximize emissions received. The antenna is scanned from 1 to 4 meters above the ground plane to further maximize the emission. Measurements are made with the antenna polarized in both the vertical and the horizontal positions. COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 56 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 8.2. TRANSMITTER ABOVE 1 GHz 8.2.1. 802.11b MODE IN THE 2.4 GHz BAND RESTRICTED BANDEDGE (LOW CHANNEL, HORIZONTAL) LOW CHANNEL RESTRICTED, PEAK, HORIZ LOW CHANNEL RESTRICTED, AVG, HORIZ DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 57 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 RESTRICTED BANDEDGE (LOW CHANNEL, VERTICAL) LOW CHANNEL RESTRICTED, PEAK, VERT LOW CHANNEL RESTRICTED, AVG, VERT COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 58 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 RESTRICTED BANDEDGE (HIGH CHANNEL, HORIZONTAL) HIGH CHANNEL RESTRICTED, PEAK, HORIZ HIGH CHANNEL RESTRICTED, AVG, HORIZ COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 59 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 RESTRICTED BANDEDGE (HIGH CHANNEL, VERTICAL) HIGH CHANNEL RESTRICTED, PEAK, VERT HIGH CHANNEL RESTRICTED, AVG, VERT COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 60 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 HARMONICS AND SPURIOUS EMISSIONS DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 61 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 8.2.2. 802.11g MODE IN THE 2.4 GHz BAND RESTRICTED BANDEDGE (LOW CHANNEL, HORIZONTAL) LOW CHANNEL RESTRICTED, PEAK, HORIZ COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 62 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 LOW CHANNEL RESTRITED, AVG, HORIZ COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 63 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 RESTRICTED BANDEDGE (LOW CHANNEL, VERTICAL) LOW CHANNEL RESTRICTED, PEAK, VERT LOW CHANNEL RESTRICTED, AVG, VERT COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 64 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 RESTRICTED BANDEDGE (HIGH CHANNEL, HORIZONTAL) HIGH CHANNEL RESTRICTED, PEAK, HORIZ HIGH CHANNEL RESTRICTED, AVG, HORIZ COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 65 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 RESTRICTED BANDEDGE (HIGH CHANNEL, VERTICAL) HIGH CHANNEL RESTRICTED, PEAK, VERT HIGH CHANNEL RESTRICTED, AVG, VERT COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 66 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 HARMONICS AND SPURIOUS EMISSIONS DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 67 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 8.2.3. 802.11n HT20 SISO MODE IN THE 2.4 GHz BAND RESTRICTED BANDEDGE (LOW CHANNEL, HORIZONTAL) LOW CHANNEL RESTRICTED, PEAK, HORIZ LOW CHANNEL RESTRICTED, AVG, HORIZ COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 68 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 RESTRICTED BANDEDGE (LOW CHANNEL, VERTICAL) DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 LOW CHANNEL RESTRICTED, PEAK, VERT LOW CHANNEL RESTRICTED, AVG, VERT COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 69 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 RESTRICTED BANDEDGE (HIGH CHANNEL, HORIZONTAL) HIGH CHANNEL RESTRICTED, PEAK, HORIZ HIGH CHANNEL RESTRICTED, AVG, HORIZ COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 70 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 RESTRICTED BANDEDGE (HIGH CHANNEL, VERTICAL) HIGH CHANNEL RESTRICTED, PEAK, VERT HIGH CHANNEL RESTRICTED, AVG, VERT COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 71 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 HARMONICS AND SPURIOUS EMISSIONS DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 72 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 8.3. WORST CASE RECEIVER ABOVE 1 GHz COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 73 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 8.4. WORST CASE BELOW 1GHZ VERTICAL& HORIZONTAL DATA COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 74 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 REPORT NO: 11J13629-1 FCC ID: MCLWINA2 9. AC POWER LINE CONDUCTED EMISSIONS LIMITS FCC 15.207 (a) RSS-Gen 7.2.2 TEST PROCEDURE ANSI C63.4 RESULTS COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 75 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 6 WORST EMISSIONS DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 CONDUCTED EMISSIONS DATA (115VAC 60Hz) Reading EN_B Freq.

(MHz) PK (dBuV) QP (dBuV) AV (dBuV) 0.15 0.45 16.66 0.15 0.45 16.66 54.91 40.74 40.96 53.35 39.89 40.63 35.60 30.63 31.46 36.42 31.15 31.14

--

--

--

--

--

--

Closs

(dB) 0.00 0.00 0.00 0.00 0.00 0.00 Limit QP 65.84 56.89 60.00 65.84 56.93 60.00 Margin Remark QP (dB) AV (dB) L1 / L2

-10.93

-16.15

-19.04

-12.49

-17.04

-19.37

-20.24

-16.26

-18.54

-19.42

-15.78

-18.86 L1 L1 L1 L2 L2 L2 AV 55.84 46.89 50.00 55.84 46.93 50.00 6 Worst Data COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 76 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 LINE 1 RESULTS DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 77 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 LINE 2 RESULTS DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 78 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 10. MAXIMUM PERMISSIBLE EXPOSURE FCC RULES 1.1310 The criteria listed in Table 1 shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b), except in the case of portable devices which shall be evaluated according to the provisions of 2.1093 of this chapter. COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 79 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 IC RULES IC Safety Code 6, Section 2.2.1 (a) A person other than an RF and microwave exposed worker shall not be exposed to electromagnetic radiation in a frequency band listed in Column 1 of Table 5, if the field strength exceeds the value given in Column 2 or 3 of Table 5, when averaged spatially and over time, or if the power density exceeds the value given in Column 4 of Table 5, when averaged spatially and over time. COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 80 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 EQUATIONS Power density is given by:

S = EIRP / (4 * Pi * D^2) Where S = Power density in W/m^2 EIRP = Equivalent Isotropic Radiated Power in W D = Separation distance in m Power density in units of W/m^2 is converted to units of mWc/m^2 by dividing by 10. Distance is given by:

D = SQRT (EIRP / (4 * Pi * S)) Where D = Separation distance in m EIRP = Equivalent Isotropic Radiated Power in W S = Power density in W/m^2 For multiple collocated transmitters operating simultaneously in frequency bands where the limit is identical, the total power density is calculated using the total EIRP obtained by summing the Power * Gain product (in linear units) of each transmitter. Total EIRP = (P1 * G1) + (P2 * G2) + ... + (Pn * Pn) where Px = Power of transmitter x Gx = Numeric gain of antenna x In the table(s) below, Power and Gain are entered in units of dBm and dBi respectively and conversions to linear forms are used for the calculations. LIMITS From FCC 1.1310 Table 1 (B), the maximum value of S = 1.0 mW/cm^2 From IC Safety Code 6, Section 2.2 Table 5 Column 4, S = 10 W/m^2 RESULTS Band Mode 2.4 GHz WLAN

(m) 0.20 Separation Output Antenna Distance Power

(dBm) 24.20 Gain

(dBi) 2.05 IC Power Density

(W/m^2) 0.84 FCC Power Density

(mW/cm^2) 0.084 COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 81 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.

REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 11. SETUP PHOTOS ANTENNA PORT CONDUCTED RF MEASUREMENT SETUP ANTENNA PORT CONDUCTED PHOTO RADIATED RF MEASUREMENT SETUP FOR PORTABLE CONFIGURATION X-AXIS WITH LONG ENDS AT REAR PHOTO COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 82 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 X-AXIS WITH LONG ENDS AT FRONT PHOTO Y-AXIS WITH LONG ENDS AT RIGHT PHOTO COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 83 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 Y-AXIS WITH LONG END AT LEFT PHOTO Z-AXIS WITH LONG ENDS AT TOP PHOTO COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 84 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 Z-AXIS WITH LONG ENDS AT BOTTOM PHOTO RADIATED RF MEASUREMENT SETUP RADIATED FRONT PHOTO COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 85 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 RADIATED BACK PHOTO POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP LINE CONDUCTED FRONT PHOTO COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 86 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. REPORT NO: 11J13629-1 FCC ID: MCLWINA2 DATE: FEBRUARY 09, 2011 IC: 2878D-WINA2 LINE CONDUCTED BACK PHOTO END OF REPORT COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET, FREMONT, CA 94538, USA Page 87 of 87 TEL: (510) 771-1000 FORM NO: CCSUP4701C FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS.