Honeywell Contactless Smart Card Reader Installation Instructions Model: JT-MCR45(55)-32C Rev 1.3, Apr.18th, 2014 WHAT IS THE Contactless Smart Card Reader?
place a grommet or electrical tape around the edge of the hole The Reader is an RFID Contactless Smart Card reader for use with to protect the wire from chaffing. access control systems. These installation instructions contain the following information:
Mounting Instructions Connecting the reader to a host using the wiegand interface Testing and operation of the reader How to install the PSAM card?
5. Attach the reader to the mounting surface using the appropriate screws (not supplied). The mounting template may be left in place if desired since the reader will cover it completely. HOW TO CONNECT THE READER TO THE HOST If the card reader is configured as software encrypted, it is no need The Reader is supplied with an 18-inchpigtail, having a the PSAM card. But if it is hardware encrypted, the PASM card is 7-conductor cable. To connect the reader to the host, perform the necessary. The steps to install the PSAM card are as follow:
following steps:
1. Open the back cover of the reader first and then you could 1. Prepare both the reader cable and host cables by cutting the find the socket of PSAM card. cable jacket back 1 inches and strip the wires inch. 2. Push the deck lid on the socket in the direction of sign 2. Splice the reader pigtail wires to the corresponding host wires OPEN, and then open it. 3. Insert the flat side of PASM card (NOT THE SIDE WHICH HAS MISSING CORNER) alone the guide groove on the upper lid. Let the face which has contacts up (THIS SIDE and cover each connection (see Figure 1). 3. Trim and cover all conductors that are not used. Figure 1 below shows how you should wire the reader to the host. WILL FACE DOWN AFTER CLOSE THE LID). After that, close the upper lid and push it in the opposite direction when open it, make sure the lid be locked and fastened reliably. 4. Close the back cover of the card reader. HOW TO MOUNT THE READER To surface mount the reader, perform the following:
1. Determine an appropriate mounting position for the reader. Ideally, for the maximum operating distance, avoid mounting the reader directly on metal surfaces. Honeywell ModelJT-MCR45-32C Figure 1 Red
+8~16VDC Black Ground White Data1 Green Data0 Brown LED Control Purple Tamper +
Orange Tamper -
Wiring Notes:
1. The individual wires coming out of the reader are color coded 2. Peel off the back of the self-stick mounting label template according to the recommended wiegand standard. included with the unit and position it at the desired mounting 2. When using a separate power supply for the reader, the reader position. power supply and host must have a common ground. 3. Using the template as a guide, drill two holes (hole size is 3. The recommended cable depends on the distance from the indicated on mounting template) for mounting the reader to reader to the host. See Table 1 below for the correct wire gage the surface. 4. Drill a 1/2 (13 mm) hole for the cable. If mounting on metal, based upon distance. Larger wire gauges (smaller numbers) are desirable. The wire must be stranded with an overall 1 / 2 shield, either foil or braided. Output Interface: Wiegand 32 ( User-defined Support) 4. The cable shield wire on the reader should be attached to an Tamper Output: NC Honeywell Earth ground (best) or signal ground connection at the panel or power supply end of the cable. This configuration is best for shielding the reader cable from external interference. TABLE 1: WIRE GAGE SPECIFICATIONS Distance Gage 5 Conductor 6 Conductor
!
Card Supported: ISO14443 CPU Card Card Read DistanceNormal Use: More than 3cm Operating Temperature Range: -25 F to 145 F (-31C to 63C) Operating Humidity: 0 to 95% (non-condensing) Dimensions: 3.5(89mm) L x 3.5(89mm) W x 0.8(20mm) D
= 200 ft.
(61m)
=300 ft.
(91m)
= 500 ft.
(153 m) 22 Alpha 1295C Alpha 1296C FCC STATEMENT :
20 Alpha 58126 Alpha 58126 subject to the following two conditions:
This device complies with Part 15 of the FCC Rules. Operation is 18 Alpha 58136 Alpha 58136 1) 2) This device may not cause harmful interference, and This device must accept any interference received, including Recommended cable is only a guideline, use any manufacturer that interference that may cause undesired operation. meets the gage and shield specifications. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority HOW TO TEST AND OPERATE THE READER to operate the equipment. The reader should be tested after wiring it to the host. Do this by NOTE: This equipment has been tested and found to comply with performing the following steps:
the limits for a Class B digital device, pursuant to Part 15 of the 1. Power up the reader. The LED and beeper will activate three FCC Rules. These limits are designed to provide reasonable times. This indicates that the reader is working properly. protection against harmful interference in a residential installation. 2. Present the configuration card to the reader. Power up the This equipment generates uses and can radiate radio frequency reader. The LED and beeper will active two times in 1 ~ 10 energy and, if not installed and used in accordance with the seconds. This indicates that the reader is configuration instructions, may cause harmful interference to radio successful.(Must configured in 3 seconds after power up) communications. However, there is no guarantee that interference 3. Present a Contactless Smart Card to the reader. The LED will will not occur in a particular installation. If this equipment does momentarily flash green and beep will activate one time (if cause harmful interference to radio or television reception, which the reader is the factory default configuration). This indicates can be determined by turning the equipment off and on, the user is that the card was read properly by reader. encouraged to try to correct the interference by one or more of the 4. After the card data is processed by the host, the host turn the following measures:
LED green. Refer to the host description of the LED operation if the reader LED is controlled by the host. eceiving antenna. SPECIFICATIONS Electrical Characteristics:
Frequency: 13.56 MHz that to which the receiver is connected. help. Power Supply Type: Linear or switching; ripple < 50 mVpp Operating Voltage Range: 8.0 16 VDC Maximum input current: 120 mA Maximum Cable Distance to Host: 500 ft. (150 meters) 2 / 2 JSM0075004-13