DT8035 DUAL TEC Motion Sensor - Installation Instructions QUICK LINKS Mounting Location Guidelines Open the Sensor Mount the Sensor Sensor Components and Settings Wire the Sensor Walk Test the Sensor Detection Patterns Relay Operation Troubleshooting Sensor Specifications Accessories Approval / Listings Mounting location guidelines:
The optimal range is obtained at a mounting height of 7 6 (2.3 m). Allow a clear line-of-sight to all areas to protect. Do not directly face windows. Avoid close proximity to moving machinery, fluorescent lights, and heating/cooling sources. For use in applications with pets up to 100 pounds. Top 1. Turn the arrow to point to the Unlock symbol. 2. Press firmly on housing latch. 3. Gently separate the front and rear housing. Top
[A] = Wall mounting holes.
[B] = Corner mounting holes. The rear tamper plate MUST be mounted to a stud, solid wood, or with a robust wall anchor.
- 2 -
Top Top Top LED Red Power Up Slow Blink Yellow OFF Green OFF Walk Test Normal Trouble ON Alarm ON Microwave ON PIR ON Fast Alarm Blink ON Microwave OFF OFF ON PIR Top Zones A 2 Look-down B 18 Lower C 46 Intermediate D 36 Long Top 1. Close the sensor and apply power to the sensor. Initialization is complete when the LED stops flashing slowly
(about 30 seconds). 2. Walk through the detection area and observe the LED. 3. Adjust the microwave range as necessary to meet installation requirements. Walk test mode is active for 10 minutes, then automatically exits test mode, disables the LED and enters normal operation mode. For an additional 10 minute walk test, enable Walk Test mode again with the Flashlight feature:
Note: In Walk Test mode the LED is active regardless of the LED Enable/Disable Dip switch setting. Flashlight Feature:
1. Use a flashlight with a bright light beam, and stand within 4 (1.2 m) of the sensor. 2. Swing past the light beam across the sensor IR window 3-5 times, holding the beam on the window for 0.5 second each pass. The flashlight feature is only available for the first 24 hours after installation.
- 3 -
RELAY OPERATION Alarm Relay 1 For information on Trouble conditions, see the Troubleshooting section. Intrusion Open Trouble1 Open SENSOR STATUS Normal Closed TROUBLESHOOTING Top Alarm Relay Red LED NORMAL Closed Off TROUBLE*
Self-Test Failure1 Closed Flashing
*TROUBLE CONDITIONS:
1 Self-Test Failure conditions:
Microwave supervision failure: The sensor is operating in PIR mode only. PIR self-test failure: The sensor is disabled. Temperature compensation failure: The temperature compensation is disabled. Depending on the Trouble condition, take the following corrective actions:
Verify the power supply is sufficient (at least 9V at the sensor). Cycle power to the sensor. Walk test the sensor. If the Trouble condition does not clear, replace the sensor. Top SPECIFICATIONS Range: 40 x 60 / 12 m x 20 m Power: 9.0 - 15 VDC; 15 mA typical, 17 mA maximum, 12 VDC;
AC Ripple: 3 V peak-to-peak at nominal 12 VDC Alarm Relay: Energized Form A; 30 mA, 25 VDC, 22 Ohms resistance maximum. Alarm Relay Duration: 3 seconds Tampers: Cover & Wall; (NC with cover installed) Form A;
30 mA, 25 VDC Microwave Frequencies: 10.525 GHz RFI Immunity: 20V/m 10-1000MHz, 15V/m 1000-2700MHz PIR White Light Immunity: 6,500 Lux typical Fluorescent light filter: 50 Hz / 60 Hz. Operating Temperature: 14 to 131 F / -10 to 55 C Relative Humidity: 5 to 95%; non-condensing Temperature Compensation: Advanced Dual Slope Dimensions: 4.57 H x 2.76 W x 1.69 D /
9.8 cm H x 5.7 cm W x 4.35 cm D Weight: 3.6 oz / 102 g (net weight) Top For the latest documentation and online support information, please go to:
http://www.security.honeywell.com/hsc/resources/MyWebTech/
ACCESSORIES SMB-10
(P/N 0-000-110-01) SMB-10C
(P/N 0-000-111-01) SMB-10T
(P/N 0-000-155-01) DT8-G2 Lens Kit
(P/N DT8G2LENS5PK) Swivel Mount Bracket Swivel Mount Ceiling Bracket Swivel Mount Bracket w/Tamper Replacement Fresnel Lens Kit 5 Pack APPROVAL / LISTINGS:
FCC part 15, Class B verified IC ICES-003, Class B verified UL 639 ULC S306-03 SIA-PIR-01 Passive Infrared detector standard features for Top false alarm immunity. Product must be tested at least once each year. For appropriate wiring methods, refer to the National Electrical Code NFPA 70 and the Canadian Electrical Code (where applicable). Power must be provided by a power-limited UL603 Listed burglar alarm power supply with minimum 4 hours of standby power capability, or from a power-limited output of a UL Listed burglar alarm control unit with minimum 4 hours of standby power capability. Accessories not evaluated by UL. For UL applications, enable look down and disable pet immunity. FEDERAL COMMUNICATIONS COMMISSION STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient the receiving antenna until interference is reduced or eliminated. Move the radio or television receiver away from the receiver/control. Move the antenna leads away from any wire runs to the receiver/control. Plug the receiver/control into a different outlet so that it and the radio or television If using an indoor antenna, have a quality outdoor antenna installed. receiver are on different branch circuits. Consult the dealer or an experienced radio/TV technician for help. INDUSTRY CANADA CLASS B STATEMENT This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme la partie 15 des rgles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer dinterfrences nuisibles. (2) Cet appareil doit accepter toute interfrence reue y compris les interfrences causant une rception indsirable. For the latest U.S. warranty information, please go to: www.honeywell.com/security/hsc/resources/wa or Please contact your local authorized Honeywell representative for product warranty information. 2013 Honeywell International Inc. Honeywell and DUAL TEC are registered trademarks of Honeywell International Inc. All other trademarks are the properties of their respective owners. All rights reserved. Made in China. 2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747 www.honeywell.com/security
- 4 -
P/N 800-16553 12/13 Rev A