AMcbile GT78-V7/GT78-V8 Rugged Android Handheld Device User's Manual Copyright Copyright 2017 AMobile Intelligent Corp. All Rights Reserved. This document contains proprietary information protected by copyright. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer. Disclaimer The information in this document is subject to change without prior notice in order to improve the reliability, design and function. It does not represent a commitment on the part of the manufacturer. Under no circumstances will the manufacturer be liable for any direct, indirect, special, incidental, or consequential damages arising from the use or inability to use the product or documentation, even if advised of the possibility of such damages. About This Manual This users manual provides the general information and installation instructions for the product. The manual is meant for the experienced users and integrators with hardware knowledge of personal computers. If you are not sure about any description in this manual, consult your vendor before further handling, We recommend that you keep one copy of this manual for the quick reference for any necessary maintenance in the future. Thank you for choosing AMobile products. ARS AST A RR BE > HASSE > HEE IRE ONES Safety Symbols This symbol of CAUTION indicates that there is a danger of injury to the user or a risk of damage to the product, should warning notices be disregarded. Battery Recycle This symbol indicates that a potential hazard to personal safety exists from a laser source. When this symbol is displayed in this manual, pay special attention to the specific safety information associated with the symbol CAUTION RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Preface Do not use the power adapter that isnt made for the equipment. Supplying the equipment with inappropriate voltage may cause harm to the battery or, even worse, burn the equipment. Toprevent possible hearing damage, do not listen at high volume levels for long periods Laser Safety The device's barcode scanner that uses laser lights isa class 2 laser product. DO NOT stare into the laser beams or point the laser beam at anyone's eyes when the barcode scanner is inoperation. eee fzcie Warranty This product is warranted to be in good working order during the warranty period. Should this product fail to be in good working order at any time during this period, we will, at our option, replace or repair it at no additional charge except as set forth in the following terms. This warranty does not apply to products damaged by misuse, modifications, accident or disaster. Vendor assumes no liability for any damages, lost profits, lost savings or any other incidental or consequential damage resulting from the use, misuse of, or inability to use this product. Vendor will not be liable for any claim made by any other related party. Vendors disclaim all other warranties, either expressed or implied, including but not. limited to implied warranties of merchantability and fitness for a particular purpose, with respect to the hardware, the accompanying product's manual(s) and written materials, and any accompanying hardware. This limited warranty gives you specific legal rights. Return authorization must be obtained from the vendor before returned merchandise will be accepted. Authorization can be obtained by calling or faxing the vendor and requesting a Return Merchandise Authorization (RMA) number. Returned goods should always be accompanied by a clear problem des FCC Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user's authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and. used in accordance with the instructions, may cause harmful interference to radio. communications, However, there is no guarantee that interference will not occur in a particular instalation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Ruk following two conditions:
1) this device may not cause harmful interference and 2) this device must accept any interference received, including interference that may cause undesired operation of the device. FCC RF Radiation Exposure Statement:
- Operation is subject to the 1, This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter 2, This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of Oem between the radiator and your body. Caution: Exposure to Radio Frequency Radiation. 1. To comply with the Canadian RF exposure compliance requirements, this device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. 2. To comply with RSS 102 RF exposure compliance requirements, a separation distance of at least 0 cm must be maintained between the antenna of this device and all persons. Attention: exposition au rayonnement radiofrquence. 1, Pour se conformer aux exigences de conformit RF canadienne l'exposition, cet appareil et son antenne ne doivent pas tre co-localiss oU fonctionnant en conjonction avec une autre antenne ou transmetteur. 2. Pour se conformer aux exigences de conformit CNR 102 RF exposition, une distance de sparation d'au moins (0 cm doit tre maintenue entre l'antenne de cet apparell et toutes les personnes Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful Interference to co-channel mobile satellite systems. La bande 5 150-5 250 MHz est rservs uniquement pour une utilisation a Iintrieur afin de rduire les risques de brouillage prjudiciable aux systemes de satellites mobiles utilisant les mames canaux. For the frequency 5600-5650 MHz, no operation is permitted Pour la frquence 5600-5650 MHz, aucune opration est autorise. to Chapter 1 Pp af Introduction Introduction 1.2 Package Contents Upon opening the package, carefully inspect the contents. If any of the items is missing or appears damaged, contact your local dealer or distributor. The package should contain the following items:
7.85 Rugged Android Handheld Device Rechargeable Li-ion Battery Pack (Pre-installed) User Manual o USB Cable GT-78V hasnt LTE function in US version Introduction 1.3 Parts of the Device 43 24 1 Power button 9 Scan key 2 Barcode scanner 10 Speaker 3. Pogo pin 11 Battery 4 _ USB connector 12 Camera fishlight 5 Front Camera 13. Rear Camera 6 light sensor 14 NFC 7 Touch panel 15. Volume key 8 Microphone 16 SD card slot Introduction 1.4 Dimension
- tus Chapter 2 p re |
Getting Started Getting Started 2.1 Installing microSD and SIM Card To install the microSD card and/or SIM card:
2.1.1 Installing microSD card Figure 2-1 Screw off and remove the cover. Figure 2-3 Open the aerial terminals Figure 2-4 Press the metal dome on the both sides above. above to flip the module out. Figure 2-5 Follow the Figure 2-6 Open the lid Figure 2-7 Close the lid direction of red arrowto __and insert the mSD card and follow the direction open the lid of mSD slot. into the slot to lock Getting Started 2.2.1 Charging the Battery To charge the battery using a USB port:
1. Using the USB cable that comes with the device, connect the small end of the cable to the USB port on the device. 2. Then connect the other end of the USB cable to the USB port. 2.2.2 Checking the Battery Level When the charging is in process, a battery indicator will appear in the status bar showing the charging percentage. Unplug the USB cable from the device when the battery is fullycharged. 2.3 Installing/Replacing the Battery In case you need to install or replace the battery, follow the steps below to access the battery chamber and replace the battery. 2.3.1 Accessing Battery Chamber 1. Place the device on a flat surface, AC Retaining screws with the rear side facing up. Fy Loosen theretaining screws on r. the battery cover with a coin, 2. Remove the battery cover using the notch located onthe bottom edge. Battery cover notch 3, The battery is in a compartment inside. Its opening is covered by a protective lid. Insert the tip of your finger onto the top of the cover and remove it. Protective lid 2.3.2 Installing Battery 1. To install the battery, orient the battery so that the contact pins faces towards the compartment opening. Slide the battery into thebattery chamber. Torestore the protective lid, make sure the lid is oriented as shown in the photo to theright. Align the top edge of the lid with the top of theopening, Press the lid firmly into placeto ensure it is secured. _ eetting Started 6. Replace the battery cover and secure the retaining screws with a coin. evice Using the Barcode Scanner Barcode scanner is an optional feature on the GT78-V. Depending on your models, your GT78-V might be equipped with 2D barcode scanner. This section will walk you through the basic operations. Toget the information on supported barcode formats Caution: The barcode scanner uses laser lights to scan barcodes. DO NOT stare into the laser beams or point the laser beam at anyone's eyes when the barcode scanner is in operation. 4. Installing APK File As of the time of time of release, the GT78-V may not have the barcode scanner software installed. If this is the case, you must install the APK file on your GT78-V first in order to activate the scanner function. 1. Download the APK file =
(SignedBarcodeSample.apk) from the Partner Zone of our website and save the file to your pee computer first. a Android battery 2. Connect the GT78-V to that computer usinga uss. Dated cable. The GT78-V will prompts you to. Bibeam choose a USB option. Select "USB storage" to oom transfer files between your computer andthe ziss Sie: Bawsron 3. Copy the APK file from your computer to the Ba Petes GT78-V's internal USB storage or SD card. Then disconnect your computer from the GT78-V. 4, Onthe GT78-V, use the File Manager App to = = =
navigate to theAPK file. Appendices 5. Tapthe APK file and then follow the prompts to install the application. 2. Scanning the Barcode Generally a third-party barcode application will be used to process the data read by the scanner. This user manual will not cover these applications. The following steps serve as an example only to show the basic operation of the barcode scanner. 1. Toscan a 2D barcode like QR code: Launch the web browser. 2. Point the scanner window at the barcode and press either of the two Scan keys. The scanner will project an aiming beam. 3. According to the barcode scanned, the scanned data is displayed in the text field or an action is triggered . Ay scanty ppendices 3, Supported Barcode Formats 2D Model Type Formats UPC/EAN/JAN, GS1 DataBar, Code 39, Code 128, Code 32, Code 93, Linear Codabar/NW7, Interleaved 2 of 5, Code 2 of 5, Matrix2 of 5, MSI, Telepen, Trioptic, China Post;
2DStacked _| PDF417, MicroPOF417, GS1 Composite;
2p Matrix _|Az#@c Code, Data Matrix, QR Code, Micro QR Code, MaxiCode, Han Xin Code;
Inteligent Mail Barcode, Postal-i, Australian Post, British Post, Canadian Postal Post, Japanese Post, Netherlands (KIX) Post, Postnet, Planet Code;
OCR Option | OCR-A, OCR-8, 138 (MICR) Appendices GPS reveiver 1575.42 INFC 13.56 12.01 dBuA/m @10m Bluetooth 24022480 1.27
[Bluetooth LE 2402~2480 1.33
[802.11 b/g/n 2412~2472 17.31
{802.11 a/n 5180~5320 16.14
|GSM 900. 880~915, 925~960 33,
[Gsm 1800 1710~1785, 1805~1880 33,
[WCDMA Bandi_|_1920~1980, 2110-2170 22
[WACMA Bands. 880~915, 925~960 22 LTE Band1 1920~1980, 2110~2170 22 LTE band3 1710~1785, 1805~1880 22 LTE band? 2500~2570, 2620~2690 22
[LTE bands 880~915, 925~960 22
[LTE band20 832~862, 791~821 22 ppendices Hereby, Hong Kong AMobile Intelligent Corp. Limited Taiwan Branch declares that the radio equipment type [designation] is in compliance with Directive 2014/53/EU The full test of the EU declaration of conformity is available at the following internet address https://www.amobile-solutions.com/
Restriction of SGHz pictogram and country table This production is restricted indoor use only for 5150-
5250MHz a=
ce SAR is measured with the device at __mm to the body, while trans-
mitting at the highest certified output level in all frequency bands of the device. The maximum SAR value is W/kg(head/body) and _ W/kg(limbs) averaged over 10 gram of tissue