LEGAL INFORMATION All rights reserved. No part of this publication may be quoted, reproduced, translated or used in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of IPRO mobile which is hereinafter named IPRO in this user guide Notice IPRO reserves the right to make modifications on print errors or update specifications in this guide without prior notice. Disclaimer IPRO expressly disclaims any liability for faults and damages caused by unauthorized modifications of the software. Images and screenshots used in this guide may differ from the actual product. Content in this guide may differ from the actual product or software. Trademarks The Bluetooth trademark and logos are owned by the Bluetooth SIG, Inc. and any use of such trademarks by IPRO is under license. microSDXC Logo is a trademark of SD-3C, LLC. Zafiro Quick Start Guide 1 2 Getting to Know Your Phone Installing the SIM Cards/microSDXC Card and Battery Power off your phone before installing or removing the SIM cards/microSDXC card. And power off your phone before removing or replacing the battery.
WARNING!
To avoid damage to the phone, do not use any other kind of SIM cards, or any non-standard SIM card cut from a SIM card. You can get a standard SIM card from your service provider. Insert your fingernail into the slot at the bottom left of 1. the back cover and lift it up gently. 3 2. Hold the SIM card with the cut corner oriented as shown and slip them into the card slots. 4 3. 4. Hold the SIM card with the cut corner oriented as shown and slip them into the card slots. Insert the battery by aligning the metal contacts on the battery with the metal contacts in the battery compartment. Gently push down on the battery until it clicks into place. 5. Align the back cover with the back of the phone and press the cover back into place. Ensure that all the tabs are secure and there are no gaps around the cover. Charging the Phone Your phones battery should have enough power for the phone to turn on, find a signal, and make a few calls. You should fully charge the battery as soon as possible.
WARNING!
Use only IPRO-approved chargers and USB cables. The use of unapproved accessories could damage your phone or cause the battery to explode. 1 Connect the adaptor to the charging jack.Ensure that the adaptor is inserted in the correct direction. 2 Connect the charger to a standard AC power outlet. 3 Disconnect the charger when the battery is fully charged. NOTE:
If the battery is extremely low, you may be unable to power on the phone even when it is being charged. In this case, try again after charging the phone for at least 20 minutes. Contact the customer service if you still cannot power on the phone after prolonged charging. NOTE:
If the screen freezes or takes too long to respond, try pressing and holding the Power key for about 10 seconds to restart the phone. 5 6 Product Safety Information Dont make or receive phone calls while driving. Never text while driving. Keep your phone at least 5 mm away from your body while making calls. Small parts may cause choking. Your phone can produce a loud sound. To prevent possible hearing damage, do not listen at high volume levels for long periods. Exercise caution when holding your phone near your ear while the loudspeaker is in use. Avoid contact with anything magnetic. Keep away from pacemakers and other electronic medical devices. Turn off when asked to in hospitals and medical facilities. Turn off when told to on aircraft and at airport. Turn off when near explosive materials or liquids. Dont use at gas stations. Your phone may produce a bright or flashing light. Dont dispose of your phone in fire. Avoid extreme temperatures. Avoid contact with liquids. Keep your phone dry. Do not attempt to disassemble your phone. Dont rely on your phone as a primary device for emergency communications. FCC Warning Specific Absorption Rate (SAR) information SAR tests are conducted using standard operating positions accepted by the FCC with the phone transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value, in general, the closer you are to a wireless base station antenna, the lower the power output. Before a new model phone is a available for sale to the public, it must be tested and certified to the FCC that it does not exceed the exposure limit established by the FCC, Tests for each phone are performed in positions and locations (e.g. at the ear and worn on the body)as required by the FCC. For body worn operation, this mobile phone has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal and that positions the handset a minimum of 1.0cm from the body. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by 7 8 turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help. 9