FCC ID: 2AXV4-3601 Toy RC Hydro Racers with Pool COMPOSITE

HYDRO RACERS 6+

Contents 2 Hydro Racers 2 Controls 2 USB-C Cables 1 Inatable Pool Raceway Power Knob Forward/Reverse Joystick CONTENTS AND BATTERY INSTALLATION/CHARGING Battery Installation Battery Charging The Hydro Racers each include a built-in 1.2V 120mAh NIMH rechargeable battery. The controls each require 4 AA batteries (not included). 1. Use a Phillips-head or cross screwdriver to loosen the screw securing the battery cover on the bottom of the remote. 2. Insert the batteries, ensuring the correct polarity as per diagrams on the battery compartment. 3. Replace battery cover and tighten the screws after installation. Status Light Left/Right Joystick Charging Cord Charging Port Charging LED Indicator The Hydro Racers each use an internal rechargeable battery that is not replaceable. If the battery no longer stays charged, dispose of it properly according to local disposal requirements. CAUTION: If the rechargeable battery leaks uid, dispose of the boat immediately. Do not allow uid to come in contact with skin or eyes. 1. Make sure the boat is powered off and not touching water before charging. 2. Rotate anticlockwise to remove the helmet. Insert the USB-C cable into the port as shown in the illustration to the left. IMPORTANT: Do not use excessive force when connecting the USB-C cable. If there is resistance, check alignment and try again. 3. There are 2 ways to charge the boat. The red LED indicator located near the port will turn on while the boat is charging and turn off when it is fully charged. a. Connect USB-C cable from remote control to the boat USB socket for charging. b. Insert the USB-C cable (not included) into the port on the boat. Insert the other end into an AC wall adapter (not included). NOTE: The average charging time is approximately 40 minutes (via 5.0V/2A USB wall charger). 4. Once in low-battery mode, the boat will slow down signicantly. 5. The boat will run for up to 10 minutes when fully charged. 1. Inate the pool raceway and then ll with water to just above the air valve in the center track divider (approximately 2.5 inches of water). 2. Ensure all portions of the raceway are inated including the outer and Track Setup inner walls. Pairing Your Hydro Racers utilize an automatic 2.4GHz digital channel selection system that allows up to 10 individual players to race side by side in the same wireless range without interference. For Solo Players 1. Before starting, make sure that both the remote control and boat are off. 2. First turn on the remote control by rotating the power switch clockwise.The LED indicator will start ashing slowly indicating that the remote control is ready for syncing. 3. Next, set the boat in water. 4. The boat and remote control will automatically pair once both are activated. 5. The remote control LED will stop ashing once successfully paired and ready for use. 6. If pairing is unsuccessful in 60 seconds, the remote control and boat will go into sleep mode. Turn off the remote control, remove the boat from water and repeat steps 1 4. 7. If the remote control and boat have not been used for 5 or more minutes, both will turn off and need to be restarted. For Mulitple Players 1. Make sure to power off all boats and controls. 2. One by one, each player should sync their boat and remote control by following the steps listed in the IMPORTANT: After syncing each boat, make sure to leave each boat on until all players have 3. If there are problems syncing, all players should turn off their controls and remove the boat from Solo Players section. completed the syncing process. water and restart the process. There are 2 joysticks on each remote control. The left joystick controls forward and reverse direction. The right joystick controls left and right direction. Boat Controls Troubleshooting The LED indicator on the remote control will turn solid when paired with a Hydro Racer. If the light continues to pulse, refer to pairing instructions. Hydro Racers must be placed in water in order to function. The water sensors located on the bottom of the boats will detect when not submerged and will stop motor operation. Water Sensors Never operate boats without proper adult supervision. Do not operate during thunderstorms or rain. Use pool racetrack only on a smooth, level surface. Splashing may occur. Do not place pool racetrack on carpet or other oors that may be damaged by water. Operate boats only in pool racetrack or swimming pools lled with salt-free water. Avoid exposure to saltwater, as this will corrode boat parts. Never submerge remote control in water. Disconnect battery when not in use to avoid accidental operation. Do not use people or animals as obstacles inside pool. Do not run boat into pool walls, objects, or other hard surfaces, as this will cause damage to the boat. Keep ngers, hair, and loose clothing away from the spinning propellers while the boat is operational. Do not leave boat or remote control near sources of heat or under direct sunlight for extended periods. Do not leave boat or remote control outside overnight. Always remove boat from water when not in use. Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries. Alkaline batteries are recommended. Use only the specied voltage. Insert batteries using the correct polarity. Always use, replace, and recharge (if applicable) batteries under adult supervision. Do not short-circuit the battery supply terminals. Do not dispose of batteries in re, batteries may explode or leak. Remove batteries before storing. Recycle or dispose of batteries according to federal, state, and local laws. Keep these instructions for future reference. Rechargable Battery Warnings: (Non-Replaceable Battery) This product contains batteries that are non-replaceable. There is a risk of re and personal injury if battery is punctured, damaged, or misused. Do not dismantle, crush, incinerate or short-circuit battery. Never expose battery to extreme temperatures or moisture. Keep away from ammable materials and direct sunlight. Only charge using the provided charger, cable, and/or adapters. Rechargeable battery is only to be charged by an adult. Adult supervision is required while charging the battery. Allow battery to cool to room temperature before charging. Charge on a non-ammable surface and keep away from ammable products. Discontinue charging if battery becomes hot, swells, smokes, or gives off a strong odor. Battery chargers used with the product are to be regularly examined for damage to the cord, plug, enclosure, and other parts. In the event of such damage, chargers must not be used until the damage has been repaired. Recycle or dispose of battery according to federal, state, and local laws. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Sharper Image Distributed by and 2022 MerchSource, LLC. Irvine, CA 92618. All rights reserved. Model No.: 1015822 KEEP THIS INSTRUCTION MANUAL AS IT CONTAINS IMPORTANT INFORMATION FOR FUTURE REFERENCE. Due to continuous product improvements, the picture on the manual may differ slightlyfrom the actual product. Printed in China 1-800-374-2744

an || SHARPER IMAGE*

| 2001 MerchSource LLG. Ivie, CA Maden Chino ModelNo: 1015822 FCCID: 2AXV4-3601. This device complies withpart 15 of the FOCRules. Operations the subject to the following two conditions: (1) this device may not cause harmfulinterference, and

@this device must accept any interference received. including interference that may cause undesired operation. Model No.: 1015822 FCC ID: 2AXV4-3601 size:1.6mm(h)x19mm(w) size:1.6mm(h)x20mm(w) SHARPER IMAGE?

2021 MerchSource LLC. Irvine, CA. Made in China. ModelNo; 1015822) FCC ID: 2AXV4-3601 This device complies with part 15 of the FCC Rules. Operation is the subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with part 15 of the FCC Rules. Operation is the subject to the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. size:10mm(h)x72.5mm(w)

APPENDIX E Hongdi Toys Factory Attention: Certification reviewer RE: Request for Confidentiality FCC ID: 2AXV4-3601 To Whom It May Concern:

confidentiality 's requested

{1 Permanent C confidentiality [Complete this section if permanent certification for the ation for equipment d 0.459 of the FCC AT CFR 0.457(d) an ently confidential:

ublic review certain portions of the applic t for confidentiality is made pursuant to f the application are to be kept perman:

te, and delete unselected parts]

Request to withhold permanently from p referenced FCC identifiers. This reques Rules. In particular, the following sections 0

[Select one or more of items below, as appropria J Schematics i Block Diagrams

& Operational Description Rationale for request for confidentiality:

d development to produce the referenced product. of this application to competitors would ucts, but would also disclose successful ed considerable time and materials in research an f& Permanent confidentiality: Disclosure of the permanently confidential portions not only give them significant competitive advantages in developing similar prod ge technology developed by us. We have invest implementation of unpublished, leading e If you have questions or need further information, please contact the undersigned. Sincerely, Peg Cha Rongbin,Chen Manager 05/05/2022

APPENDIX B 05/05/2022 Federal Communications Commission 445 12" Street SW Washington, DC 20554 Subject: Limited Agency Agreement Hongdi Toys Factory FCC ID: 2AXV4-3601 To Whom It May Concern:

We, Hongdi Toys Factory , hereby authorized Intertek Testing Services to act as our Agent for the purpose of preparing application for FCC ID number 2AXV4-3601 under all applicable parts of the FCC rules and regulations. The effective date of this limited agency agreement is 05/05/2022. The Limited Agency Agreement expires on 07/25/2022, unless sooner terminated or extended by written notice to Intertek Testing Services and the Federal Communications Commission. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. The applicant is not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 862, and no party to the application is subject to a denial of federal benefits pursuant to that section. If you have any questions or comments, please do not hesitate to contact me. Sincerely, Roxb, Chen Rongbin,Chen Manager