U3__ 2019/12/19 1. 3 2. 5 3. 14 4. 5 6 7 3 WIFI 4 4 1 2 3 4 GlocalMe : GLMU19A02 SAR 5. 3 LTE TDDB34/38/39/40/41(194M) 1 1 1 1 126*66*10mm LTE FDDB1/2/3/4/5/7/8/9/12/13/17/18/19/20/25/26/28/66 21288-2007 SAR)2.0W/kg, GB 5 8 1. WIFI 2. 3. 4. 5. 6. 7. 8. Type-C WCDMA B1/2/4/5/6/8/9/19 GSM 850/900/1800/1900 WiFi IEEE802.11b/g/n Type-C 3000mAh DC 5V 2A 1. U3SIMSIM Nano-SIM SIMMicro-SIM(
) 1GlocalMe APP 2APP 3GlocalMe APP 2. 43 SIM 5WIFI WIFIGlocalMe WIFIWIFI 3. PINSIM SIMPIN 6WIFI 192.168.43.1 0 ~ + 35 IMEI:123456789012345 SSID: GlocalMe_0000 PWD: 000000000 3C5V 2A
,ROM
, www.glocalme.com
+852-8191-2660/+86 400-699-1314
(13 service@ucloudlink.com 1A3 Copyright 2018 uCloudlink All Rights Reserved https://www.ucloudlink.com/patents 1 2 3 4 5 6 7 8 User Manual 1 2 3 4 Function Introduction Product Introduction 1. Power onPress power button for 3 seconds. 2. Power offPress power button for 5 seconds. 3. ResetPress power button for 18 seconds. BrandGlocalMe Model No.: GLMU19A02 Box Content: Device, User Manual, Type-C Cable SIM Removal tool 4. Restore Factory SettingsPress reset button for 5 seconds. 5. Battery Capacity and Signal StrengthPress the power button, Technical Specification the battery capacity will be shown in the first 3 seconds, then the Size: 126*66*10mm 6 7 LTE FDDB1/2/3/4/5/7/8/9/12/13/17/18/19/20/25/26/28/66 signal strength will be shown afterwards. LED Indicator Type Status Remarks Wi-Fi LED Indicator Signal LED Indicator Battery LED Indicator On Ready for internet connection Off No internet connection Flashing Service connecting On The signal strength is shown by strength LED indicator (4) Flashing Service Error On The battery capacity is shown by strength LED indicator (4) Flashing Charging Local SIM 1. Local SIM is supported by U3, Only insert Nano-SIM card (small card). 2. Use a needle to pull out the SIM cards as shown in the picture below. Please contact customer service if any issue encountered 3. U3 device does not support SIM cards with PIN code, if you want to use this type of SIM cards, please unlock the PIN code first. 5 8 1. Wi-Fi LED Indicator 2. Battery LED Indicator 3. Signal LED Indicator 4. Strength LED Indicator 5. Handle position for opening 6. Power button front panel 7. Reset button 8. Type-C(Input) LTE TDDB34/38/39/40/41(194M) WCDMA B1/2/4/5/6/8/9/19 GSM 850/900/1800/1900 CDMA/EVDO: BC0 BC1 Wi-Fi: IEEE802.11b/g/n Type-C (Input) Battery Capacity: 3000mAh Power Input: DC 5V 2A Warning Specific Absorption Rate (SAR) information. SAR tests are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value, in general, the closer you are to a wireless base station antenna, the lower the power output. Before a new device can be made available for sale to the public, it must be tested and certified by the FCC that it does not exceed the exposure limit established by the FCC, Tests for each device are performed in positions and locations as required by the FCC. For body worn operation, this device has been tested and meets the FCC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal and that positions the device a minimum of 1.0 cm from the body. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause. Undesired operation.Any Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: This equipment has been tested and complies with the limits for a Class B digital device, pursuantto part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio Copyright 2018 uCloudlink All Rights Reserved Information on the disposal and recycling of the device This symbol (with or without a solid bar) on the device, batteries (if included), and/or the packaging, indicates that the device and its electrical accessories (for example, a headset, adapter, or cable) and batteries should not be disposed of as household garbage. These items should not be disposed of as unsorted municipal waste and should be taken to a certified collection point for recycling or proper disposal. For detailed information about device or battery recycling, contact your local city office, household waste disposal service, or retail store. Disposal of the device and batteries (if included) is subject to WEEE. Directive Recast (Directive 2012/19/EU) and Battery Directive (Directive 2006/66/EC). The purpose of separating WEEE and batteries from other waste is to minimize the potential environmental impacts and human health risk of any hazardous substances that may be present. communications. However, there is no guarantee that interference will not occur during installation. If the device does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is suggested to try to correct the interference by the following measures:
--Reorient or relocate the receiving antenna.
--Increase the distsnce between the equipment and receiver.
--Connect the equipment to an outlet on a different circuit to the receiver.
--Consult the manufacturer or an experienced radio/TV technician for help.
{Specific Absorption Rate (SAR) Your mobile device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves recommended by international guidelines. These guidelines were developed by the independent scientific organization IEEE/ANSI and include safety margins designed to assure the protection of all persons, regardless of age and health. The guidelines use a unit of measurement known as Specific Absorption Rate, or SAR. The SAR limit for mobile devices is 1.6 W/kg and the highest SAR value for this device is1.567 W/kg when tested at body with 10 mm distance. As SAR is measured utilizing the devices highest transmitting power, the actual SAR of this device while operating is typically below that indicated above. This is due to automatic changes to the power level of the device to ensure it only uses the minimum power required to communicate with the network. The tests are carried out in accordance with FCC 47 PART 2.1093, IEEE 1528 and ANSI/IEEE C95.1. FCC ID:2AC88-GLMU19A02 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. facebook.com/GlocalMe GlocalMe WeChat platform Hong Kong uCloudlink Network Technology Limited E-mail: service@ucloudlink.com Hotline: +852 8191 2660 or +86 400 699 1314 China Facebook: GlocalMe Instagram: @GlocalMeMoments Twitter: @GlocalMeMoments YouTube: GlocalMe Address: SUITE 603, 6/F, LAWS COMMERCIAL PLAZA, 788 CHEUNG SHA WAN ROAD, KOWLOON, HONG KONG This product and related system are protected by one or more of uCloudlinks patents, details please refer to https://www.ucloudlink.com/patents Copyright 2018 uCloudlink All Rights Reserved