FCC ID: 2AYI8-WLSA0201 Freedom Charge Magnetic 2in1

Omniklad 5W/7.5W/10W/15W Plug in DC adapter to the wireless charger using the cable provided .When the charger is tuned on, the charger is turned on, the LED light will flick alternately in white for 2S then go off. Max 15W Omniklad DC 19V-1.58A Place your device on the center of the charging plate. The white light stays on white charing. If the device deviates from the center of the product, the wireless charging function may be affected. Magnetic Wireless Charger DC adapter WLS-A02-01 Adapter Input:DC19V--1.58A Adapter Input:Output (Wireless): 5W & 7.5& 10W & 15W 130.87x124.03x124.03 LED Behavior:

A. While powered up but not charging: LED off B. While powered up and charging: LED on C. While powered but in FOD/ Error/ Fault condition:

LED Blinks (@ 1.0Hz)

-Blinking sequence is 0.5 sec on, then 0.5 sec off

-Blinking continues while fault condition exists. FCC This device complies with part 15 of the FCC Rules. Operations subject to the following two conditions : ( 1 ) This device maynot cause harmful interference , and ( 2 ) this device must acceptany interference received, including interference that may cause undesired operation . This equipment has been testedand found to comply with the limits for a Class B digital devicpursuant to part 15 of the FCC Rules . These limits are designed to provide reasonable protection against harmful interferencein a residential installation . This equipment generates, usesInd can radiate radio frequency energy and , if not installedand used in accordance with the instructions , may causeharmful interference to radio communications . However there is no guarantee that interference will not occur in a particular installation . If this equipment does cause harmful interference to radio or television reception , which can be determined by turning the equipment off and on , the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit differentfrom that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help. CAUTION : To comply with the limits of the Class B digital device, pursuant to Part 15 of the FCC Rules , this device mustbe used with certified peripherals and shielded cables . All peripherals must be shielded and grounded . Operation with non-certified peripherals or non-shielded cables may resultin interference to radio or reception. Caution : Any changes or modifications not expressly approved by the party responsiblefor compliance could void the users authority to operate the equipment .

Freedom Charge Magnetic 2in1 Model: WLS-A02-01 FCC ID: 2AYI8-WLSA0201 Input: 19V 1.58A Output1: 5W Wireless Output2: 5W/7.5W/10W/15W Made in China 11.5mm 50.6mm 19.7mm 38mm 2.8mm 25.3mm

HONOTO TECHNOLOGY CO., LTD Agent Authorization Company: HONOTO TECHNOLOGY CO., LTD Address: 9 ORCHARD ROAD, SUITE 102 LAKE FOREST, California 92630 United States of America Product Name: Freedom Charge Magnetic 2in1 Model Number(s): WLS-A02-01 Product Description: Freedom Charge Magnetic 2in1 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Name:

Kem Lye Company: HONOTO TECHNOLOGY CO., LTD Date: 2021-08-27

HONOTO TECHNOLOGY CO., LTD Declaration Letter Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AYI8-WLSA0201 11/4/2021 Pursuant to KDB 680106 of the HONOTO TECHNOLOGY CO., LTD hereby declare our product which is an inductive wireless power transfer applications that meet all of the following requirements are not required to submit a KDB inquiry for devices approved usinga PAG for equipment approved using certification to address RF exposure compliance. 1) Power transfer frequency is 0.110-0.205MHz which is less than1 MHz 2) Output power from each primary coil is equal to 15 watts max 3) The system may consist of more than one source primary coils, charging one or more clients. If more than one primary coil is present, the coil pairs may be powered on at the same time. 4) Client device is placed directly in contact with the transmitter 5) The EUT is a mobile device. 6) The aggregate H-field strengths at 15 cm surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. Yours sincerely, Honoto Technology Co., LTD Contact person: Kem Lye

Honoto Technology Co., LTD Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2021-08-25 Subject; Request for Confidentiality FCC ID: 2AYI8-WLSA0201 To Whom It May Concern, Pursuant to the provisions of the Commission's rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Bd Schematic Diagram XI Block Diagram Gi Parts List XX] Operational Description

(J Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regi in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring t business sensitive information remains confidential until the actual marketing of newly i authorized devices, we request Short Term Confidentiality of the following attachment(s J External Photos XX] Test Setup Photos Dd Internal Photos User Manual

[For 45 days, pursuant to Public Notice DA 04-1705. OR

[I For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label form correspondence during the certification review process cannot be granted documents and this information will be available for public review once the authorization is issued. Sincerely 4, VL ay A Honoto Technology Co., LTD Contact person: Kem Lye