User manual Product: Bluetooth Low Energy module Model: HRM1062 For OEM integration only device cannot be sold to general public. Therefore we will not supply the Users manual, the installation manual is the official for OEM. FCC ID: VIYHRM1062 IC: 7305A-HRM1062 Operational Information This module has been tested and found to comply with the limits for a Class B digital device pursuant to Part15 of FCC rules. This module complies with Part15 subpart C of the FCC rules. Customers should check Part15 subpart B compliance with their own final products and conduct certification if needed. Caution Any changes or modifications are not expressly approved by Hosiden responsible for compliance could void the users authority to operate the equipment. Requirement of Labeling Please describe the following item on the final product including this module:
or Contains Transmitter Module FCC ID: VIYHRM1062 Contains FCC ID: VIYHRM1062 or Contains Transmitter Module IC: 7305A-HRM1062 Contains IC: 7305A-HRM1062 Requirement of Users Manual Statement This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. This device is intended only for OEM integrators under the following conditions:
1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 condition above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following: Contains FCC ID: VIYHRM1026A. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to Industry Canada Statement the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1) lappareil ne doit pas produire de brouillage;
2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that is deemed to comply without maximum permissive exposure evaluation (MPE). Cet quipement est conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles dexposition aux frquences radiolectriques (RF) CNR-102 de lIC. Cet quipement met une nergie RF trs faible qui est considre comme conforme sans valuation de lexposition maximale autorise (MPE). This device is intended only for OEM integrators under the following conditions:
(For module device use) 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 condition above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 1 condition ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:
Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling The final end product must be labeled in a visible area with the following: Contains IC:
7305A-HRM1062. Plaque signaltique du produit final Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC: 7305A-HRM1062". Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. Product Specification 1. BLUETOOTH SPECIFICATIONS BT core spec version:
version 4.2 Supported profiles:
Operation channels:
RX Sensitivity:
2. RADIO SPECIFICATIONS GATT and Original profile 2,402 + 2N MHz (N=0,1,2,39, 2MHz step)
-96dBm (1Mbps, <=37bytes, BER=1E-3) Frequency range:
2,360MHz - 2,500MHz Operation frequency range:
2,402MHz 2,480MHz Modulation:
GFSK (Spread spectrum is not used.) Max tuneup tolerance:
+4dBm Channel list:
Data rate:
Output power can be configurable following values.
+4dBm, 0dBm, -4dBm, -8dBm, -12dBm, -16dBm, -20dBm, -40dBm 2,402 + N MHz (N=0,1,2,.....78) 1MHz step, 79channels (for non-BLE 1Mbps) 2,402 + 2N MHz (N=0,1,2,.39) 2MHz step, 40channels (for non-BLE 2Mbps and BLE mode) 2Mbps, 1Mbps (BLE mode is 1Mbps only) 3. DC ELECTRICAL CHARACTERISTICS Nominal input voltage:
3.0V Operating input Voltage: 1.73.6V Absolute maximum voltage: -0.3V3.9V