FCC ID: QISAMN-LX3 Smart Phone

Quick Start Guide AMN-LX3 TUV SUD Know Your Device Before using the device, familiarize yourself with its basic operations. l To power on your device, press and hold the power button until the screen turns on. l To power off your device, press and hold the power button, and then touch

. l To restart your device, press and hold the power button, and then touch

. l Press and hold the power button for 10 or more seconds to forcibly restart your device. Volume button Micro-USB port Power button Card slot l Check out the pre-installed Tips app and master all the great features on your device. 1 1243 TUV SUD Getting Started l Do not insert or remove the SIM card when your device is powered on. l Ensure that the card is correctly aligned and that the card tray is level when you insert it into your device. l Be careful not to scratch your device or hurt yourself when using the eject pin. l Store the eject pin out of the reach of children to prevent accidental swallowing or injury. l Do not use cut or modified SIM or microSD cards with your device as these may not be recognized and could damage the card tray (slot). l If your SIM card does not match your device, please contact your carrier. Follow the instructions in the following figures to set up your device. Please use the eject pin included. Single-SIM:

Dual-SIM:

2 11 TUV SUD Dual Card Dual Standby Single Pass (dual-SIM devices only) Your device supports only dual card dual standby single pass, which means you cannot use both SIM cards for calls or data services simultaneously. l When you are on a call using SIM card 1, SIM card 2 cannot be used to make or answer calls. If someone calls SIM card 2, the caller will hear a voice message similar to "The subscriber you dialed is out of the service area" or "The subscriber you dialed cannot be connected for the moment, please try again later." The actual message will vary by service provider. l When you are using SIM card 1's data service, SIM card 2's data service will be disabled. Your device's single pass feature helps reduce power consumption and increase your device's standby time. It is not related to your service provider's network conditions. l You can enable call forwarding between SIMs on the device to avoid missed calls. 3 TUV SUD For More Information If you encounter any problems while using your device, you can obtain help from the following resources:

l Visit http://consumer.huawei.com/en to view device information, frequently asked questions and other information. l Visit http://consumer.huawei.com/en/support for the most up-to-date contact information for your country or region. Go to Settings and touch System > About phone > Legal to view legal information for your product. Go to Settings and touch System > About phone > Legal >

Safety information to view safety information for your product. Go to Settings and touch System > About phone >

Authentication info to view regulatory information for your product. Go to Settings and touch System > Certification logos to view more information on certification logos for your product. All pictures and illustrations in this guide, including but not limited to the device color, size, and display content, are for your reference only. The actual device may vary. Nothing in this guide constitutes a warranty of any kind, express or implied. 4 TUV SUD Safety Information Please read all of the safety information carefully before using your device to ensure its safe and proper operation and to learn how to dispose of your device properly. Operation and safety l To prevent possible hearing damage, do not listen at high volume levels for long periods. l Using an unapproved or incompatible power adapter, charger, or battery may damage your device, shorten its lifespan, or cause a fire, explosion, or other hazards. Ideal operating temperatures are 0 C to 35 C. Ideal storage temperatures are -20 C to +45 C. l l Pacemaker manufacturers recommend that a minimum distance of 15 cm be maintained between a device and a pacemaker to prevent potential interference with the pacemaker. If using a pacemaker, hold the device on the side opposite the pacemaker and do not carry the device in your front pocket. l Keep the device and the battery away from excessive heat and direct sunlight. Do not place them on or in heating devices, such as microwave ovens, stoves, or radiators. l Observe local laws and regulations while using the device. To reduce the risk of accidents, do not use your wireless device while driving. l While flying in an aircraft or immediately before boarding, only use your device according to instructions provided. Use of a wireless device in an aircraft may disrupt wireless networks, present a hazard to aircraft operation, or be illegal. l To prevent damage to your device's parts or internal circuits, do not use it in dusty, smoky, damp, or dirty environments or near magnetic fields. l When charging the device, make sure the power adapter is plugged into a socket near the devices and is easily accessible. l Unplug the charger from electrical outlets and the device when not in use. l Do not use, store or transport the device where flammables or explosives are stored (in a gas station, oil depot, or 5 TUV SUD chemical plant, for example). Using your device in these environments increases the risk of explosion or fire. l Dispose of this device, the battery, and accessories according to local regulations. They should not be disposed of in normal household waste. Improper battery use may lead to fire, explosion, or other hazards. l This device contains a built-in battery. Do not attempt to replace the battery by yourself. Otherwise, the device may not run properly or it may damage the battery. For your personal safety and to ensure that your device runs properly, you are strongly advised to contact a Huawei authorized service center for a replacement. FCC Regulatory Compliance Body worn operation The device complies with RF specifications when used near your ear or at a distance of 1.50 cm from your body. Ensure that the device accessories, such as a device case and device holster, are not composed of metal components. Keep the device away from your body to meet the distance requirement. Certification information (SAR) This device is also designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). The SAR limit adopted by the USA is 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported to the FCC for this device type complies with this limit. The highest SAR value reported to the FCC for this device type when using it at the ear is AMN-LX3 0.69 W/kg And when properly worn on the body is AMN-LX3 0.62 W/kg And when using the Wi-Fi hotspot function is 0.75 W/kg AMN-LX3 FCC statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 6 TUV SUD interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Any changes or modifications to this device not expressly approved by Huawei Technologies Co., Ltd. for compliance could void the user's authority to operate the equipment. 7 TUV SUD Legal Notice Trademarks and Permissions

,

, and are trademarks or registered trademarks of Huawei Technologies Co., Ltd. Android is a trademark of Google Inc. LTE is a trademark of ETSI. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Huawei Technologies Co., Ltd. is under license. Wi-Fi, the Wi-Fi CERTIFIED logo, and the Wi-Fi logo are trademarks of Wi-Fi Alliance. Privacy Policy To better understand how we protect your personal information, please see the privacy policy at http://

consumer.huawei.com/privacy-policy. Copyright Huawei Technologies Co., Ltd. 2019. All rights reserved. THIS DOCUMENT IS FOR INFORMATION PURPOSE ONLY, AND DOES NOT CONSTITUTE ANY KIND OF WARRANTIES. 8 TUV SUD 96725610_01 TUV SUD

2019-7-3

, 1 , 4 TUV SUD 2019-7-3

, 2 , 4 TUV SUD 2019-7-3

, 3 , 4 TUV SUD 2019-7-3

, 4 , 4 TUV SUD

AMN-LX3 Smart Phone External Photos of AMN-LX3 2019-4-8 Page 1, Total 5 TUV SUD AMN-LX3 Smart Phone 1. Front-AMN-LX3 Page 2, Total 5 2019-4-8 TUV SUD AMN-LX3 Smart Phone 2. Back- AMN-LX3 2019-4-8 Page 3, Total 5 TUV SUD AMN-LX3 Smart Phone 3. Left- AMN-LX3 4. Right- AMN-LX3 2019-4-8 Page 4, Total 5 TUV SUD AMN-LX3 Smart Phone 5. Top- AMN-LX3 6. Bottom- AMN-LX3 2019-4-8 Page 5, Total 5 TUV SUD

AMN-LX3 Smart Phone Label and Label Location:

2019-4-8 Page 1, Total 2 TUV SUD AMN-LX3 Smart Phone 2019-4-8 Page 2, Total 2 TUV SUD

Class II permissive change request letter Date (7/2/2019) BABT TCB Balfour House, Churchfield Road, Walton-on-Thames, Surrey, KT12 2TD REF: Class II permissive change, pursuant to section 2.1043, for FCC ID: QISAMN-LX3 Dear Sir or Madam, Pursuant to section 2.1043, Huawei Technologies Co., Ltd. Hereby submit a rrequest for class II permissive change to our Smart Phone, model: AMN-LX3, FCC ID: QISAMN-LX3, Grant date:2018-04-15. Description of the change:

1. Change LTE B2/4/7/28, WCDMA B2/4 and GSM B2 duplexer, the duplexer is a passive duplexer, and the parameters are same as before. 2. Change antenna tuner 4SPST. 3. Add one kind of earphone (Manufacturer: FOXCINN) The detailed difference as below:

Model LTE Band AMN-LX3 Original The same UMTS Band The same AMN-LX3 Modified LTE B2/B4/B7/B28 duplexer changed WCDMA B2/B4 duplexer changed GSM B2 duplexer changed The same The same 47140338 The same The same The same The same The same The same The same The same The same The same The same The same The same The same The same Licensed Frequency GSM IC Antenna Antenna tuner 4SPST RF conducted power Unlicensed Frequency Hardware Appearance Accessory Bluetooth 2.4GWiFi IC Antenna RAM/ROM Camera PCB USB Port SIM Dimension Color Battery Charger USB Label Earphone The same The same The same 47140285 The same The same The same The same The same The same The same The same The same The same The same The same The same The same The same MEND1532B528A02 1293-3283-3.5MM-322 MEND1532B528A02 1293-3283-3.5MM-322 EPAB542-2WH05-DH So in this FCC application for Smart Phone, AMN-LX3, FCC ID: QIS AMN-LX3

-New test report R1906H0117-R1 according to Part 22 have been submitted and in this test report only radiated spurious emission was retested with new duplexer and other test data were referred from original application test report R1904H0043-R1V1 and the test data are still effective and they are representative of the compliance of this C2PC application.

-New test report R1906H0117-R2 according to Part 24 have been submitted and in this test report all test items were retested with new duplexer applicable to representative of the compliance of this C2PC application.

-New test report R1906H0117-R3 according to Part 27 have been submitted and in this test report all test items were retested with new duplexer applicable to representative of the compliance of this C2PC application.

-New test report R1906H0117-R4 for 2.4GWiFi according to Part 15C have been submitted and in this test report only add the information of earphone without testing and all test data were referred from original application test report R1904H0043-R4 and the test data are still effective and they are representative of the compliance of this C2PC application.

-New test report R1906H0117-R5 for Bluetooth according to Part 15C have been submitted and in this test report only add the information of earphone without testing and all test data were referred from original application test report R1904H0043-R5 and the test data are still effective and they are representative of the compliance of this C2PC application.

-New test report R1906H0117-R6 for BLE according to Part 15C have been submitted and in this test report only add the information of earphone without testing and all test data were referred from original application test report R1904H0043-R6 and the test data are still effective and they are representative of the compliance of this C2PC application.

-New SAR test report R1906H0117-S1 has been submitted in this applicable to representative of the compliance of this C2PC application. In this test report all GSM1900, WCDMA Band II/VII and LTE Band 2/4/7 were retested with new duplexer and test the worst case for other modes base on test report R1904H0043-S1 and the test data are still effective and they are representative of the compliance of this C2PC application.

-New EMC report R1906H0117-E1 according to 15B had been submitted and in this test report only radiated emission was retested with new earphone and other test data were referred from original application test report R1904H0043-E1 and the test data are still effective and they are representative of the compliance of this C2PC application. So in this C2PC application below new documents was submitted:

Internal Photos BOM List Part15B Test Setup, Part15C Test Setup, Part22&24&27 Test Setup, SAR Test Setup The other documents from the original application remain unchanged, they are still effective and representative of the compliance of this C2PC application. Sincerely, For and Behalf of:

Huawei Technologies Co., Ltd. Zhangxinghai EMC Laboratory Manager E-mail: zhangxinghai@huawei.com Tel: 0086-0755-28970299 Fax: 0086-0755-89650226

Huawei Technologies Co.,Ltd. Federal Communications Commission Oakland Mills Road Columbia MD 21046 Subject:

Request for Confidentiality FCC ID:

QISAMN-LX3 To Whom It May Concern:

2019-07-03 Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Bom List Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market.

*****************************************************************************

Best Regards 18_Confidentiality Letter V1.0 TU SUD Zhang Xinghai EMC Laboratory Manager Huawei Technologies Co., Ltd. E-mail: zhangxinghai@huawei.com Tel: 0086-0755-28970299 Fax: 0086-0755-89650226 18_Confidentiality Letter V1.0 TU SUD

Huawei Technologies Co.,Ltd. Federal Communications Commission Oakland Mills Road Columbia MD 21046 2019-04-08 Statement for 2.4G Wi-FiTM QISAMN-LX3 Subject:

FCC ID:

To Whom It May Concern:

We, Huawei Technologies Co., Ltd., states that our productAMN-LX3 comply with the requirement in KDB 594280 D01 Software Configuration Control v02r01. For 2.4G Wi-Fi part, only support channels 1-11, the channel 12 and channel 13 are disabled by software in the factory, this setting is not accessible and cant active by the user or any other third-party. If have any questions concerning the above, please contact the undersigned. Best Regards Zhang Xinghai EMC Laboratory Manager Huawei Technologies Co., Ltd. E-mail: zhangxinghai@huawei.com Tel: 0086-0755-28970299 Fax: 0086-0755-89650226

**Wi-Fi is a trademark of Wi-Fi Alliance 26_2.4G Wi-Fi Declaration Letter V1.0 MiCOM Labs