FCC ID: QISKSA-LX3 Smartphone

Quick Start Guide KSA-LX3 TUV SUD Know Your Device Before using the device, familiarize yourself with its basic operations. l To power on your device, press and hold the power button until the screen turns on. l To power off your device, press and hold the power button, and then touch

. l To restart your device, press and hold the power button, and then touch

. l Press and hold the power button for 10 or more seconds to forcibly restart your device. Volume button Micro-USB port Power button Card slot l Check out the pre-installed Tips app and master all the great features on your device. 1 1243 TUV SUD Getting Started l Do not insert or remove the SIM card when your device is powered on. l Ensure that the card is correctly aligned and that the card tray is level when you insert it into your device. l Be careful not to scratch your device or hurt yourself when using the eject pin. l Store the eject pin out of the reach of children to prevent accidental swallowing or injury. l Do not use cut or modified SIM or microSD cards with your device as these may not be recognized and could damage the card tray (slot). l If your SIM card does not match your device, please contact your carrier. Follow the instructions in the following figures to set up your device. Please use the eject pin included. Single-SIM:

Dual-SIM:

2 11 TUV SUD Dual Card Dual Standby Single Pass (dual-SIM devices only) Your device supports only dual card dual standby single pass, which means you cannot use both SIM cards for calls or data services simultaneously. l When you are on a call using SIM card 1, SIM card 2 cannot be used to make or answer calls. If someone calls SIM card 2, the caller will hear a voice message similar to "The subscriber you dialed is out of the service area" or "The subscriber you dialed cannot be connected for the moment, please try again later." The actual message will vary by service provider. l When you are using SIM card 1's data service, SIM card 2's data service will be disabled. Your device's single pass feature helps reduce power consumption and increase your device's standby time. It is not related to your service provider's network conditions. l You can enable call forwarding between SIMs on the device to avoid missed calls. 3 TUV SUD For More Information If you encounter any problems while using your device, you can obtain help from the following resources:

l Visit http://www.hihonor.com to view device information and other information. l Visit http://consumer.huawei.com/en/support for the most up-to-date contact information for your country or region. Go to Settings and touch System > About phone > Legal to view legal information for your product. Go to Settings and touch System > About phone > Legal >

Safety information to view safety information for your product. Go to Settings and touch System > About phone >

Authentication info to view regulatory information for your product. Go to Settings and touch System > Certification logos to view more information on certification logos for your product. All pictures and illustrations in this guide, including but not limited to the device color, size, and display content, are for your reference only. The actual device may vary. Nothing in this guide constitutes a warranty of any kind, express or implied. 4 TUV SUD Safety Information Please read all of the safety information carefully before using your device to ensure its safe and proper operation and to learn how to dispose of your device properly. Operation and safety l To prevent possible hearing damage, do not listen at high volume levels for long periods. l Using an unapproved or incompatible power adapter, charger, or battery may damage your device, shorten its lifespan, or cause a fire, explosion, or other hazards. Ideal operating temperatures are 0 C to 35 C. Ideal storage temperatures are -20 C to +45 C. l l Pacemaker manufacturers recommend that a minimum distance of 15 cm be maintained between a device and a pacemaker to prevent potential interference with the pacemaker. If using a pacemaker, hold the device on the side opposite the pacemaker and do not carry the device in your front pocket. l Keep the device and the battery away from excessive heat and direct sunlight. Do not place them on or in heating devices, such as microwave ovens, stoves, or radiators. l Observe local laws and regulations while using the device. To reduce the risk of accidents, do not use your wireless device while driving. l While flying in an aircraft or immediately before boarding, only use your device according to instructions provided. Use of a wireless device in an aircraft may disrupt wireless networks, present a hazard to aircraft operation, or be illegal. l To prevent damage to your device's parts or internal circuits, do not use it in dusty, smoky, damp, or dirty environments or near magnetic fields. l When charging the device, make sure the power adapter is plugged into a socket near the devices and is easily accessible. l Unplug the charger from electrical outlets and the device when not in use. l Do not use, store or transport the device where flammables or explosives are stored (in a gas station, oil depot, or 5 TUV SUD chemical plant, for example). Using your device in these environments increases the risk of explosion or fire. l Dispose of this device, the battery, and accessories according to local regulations. They should not be disposed of in normal household waste. Improper battery use may lead to fire, explosion, or other hazards. l This device contains a built-in battery. Do not attempt to replace the battery by yourself. Otherwise, the device may not run properly or it may damage the battery. For your personal safety and to ensure that your device runs properly, you are strongly advised to contact a Huawei authorized service center for a replacement. FCC Regulatory Compliance Body worn operation The device complies with RF specifications when used near your ear or at a distance of 1.50 cm from your body. Ensure that the device accessories, such as a device case and device holster, are not composed of metal components. Keep the device away from your body to meet the distance requirement. Certification information (SAR) This device is also designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). The SAR limit adopted by the USA is 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported to the FCC for this device type complies with this limit. The highest SAR value reported to the FCC for this device type when using it at the ear is KSA-LX3 0.69 W/kg And when properly worn on the body is KSA-LX3 0.62 W/kg And when using the Wi-Fi hotspot function is 0.76 W/kg KSA-LX3 FCC statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 6 TUV SUD interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Any changes or modifications to this device not expressly approved by Huawei Technologies Co., Ltd. for compliance could void the user's authority to operate the equipment. 7 TUV SUD Legal Notice Trademarks and Permissions

,

,

, and are trademarks or registered trademarks of Huawei Technologies Co., Ltd. Android is a trademark of Google Inc. LTE is a trademark of ETSI. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Huawei Technologies Co., Ltd. is under license. Wi-Fi, the Wi-Fi CERTIFIED logo, and the Wi-Fi logo are trademarks of Wi-Fi Alliance. Privacy Policy To better understand how we protect your personal information, please see the privacy policy at http://

consumer.huawei.com/privacy-policy. Copyright Huawei Technologies Co., Ltd. 2019. All rights reserved. THIS DOCUMENT IS FOR INFORMATION PURPOSE ONLY, AND DOES NOT CONSTITUTE ANY KIND OF WARRANTIES. 8 TUV SUD 96725611_01 TUV SUD

Quick Start Guide KSA-LX3 Know Your Device Before using the device, familiarize yourself with its basic operations. l To power on your device, press and hold the power button until the screen turns on. l To power off your device, press and hold the power button, l To restart your device, press and hold the power button, and then touch and then touch

. l Press and hold the power button for 10 or more seconds to forcibly restart your device. Volume button Micro-USB port Power button Card slot l Check out the pre-installed Tips app and master all the great features on your device. 1 1 2 4 3 Getting Started l Do not insert or remove the SIM card when your device is powered on. l Ensure that the card is correctly aligned and that the card tray is level when you insert it into your device. l Be careful not to scratch your device or hurt yourself when using the eject pin. l Store the eject pin out of the reach of children to prevent accidental swallowing or injury. l Do not use cut or modified SIM or microSD cards with your device as these may not be recognized and could damage the card tray (slot). l If your SIM card does not match your device, please contact your carrier. Follow the instructions in the following figures to set up your device. Please use the eject pin included. Single-SIM:

Dual-SIM:

2 1 1 Dual Card Dual Standby Single Pass (dual-SIM devices only) Your device supports only dual card dual standby single pass, which means you cannot use both SIM cards for calls or data services simultaneously. l When you are on a call using SIM card 1, SIM card 2 cannot be used to make or answer calls. If someone calls SIM card 2, the caller will hear a voice message similar to "The subscriber you dialed is out of the service area" or "The subscriber you dialed cannot be connected for the moment, please try again later." The actual message will vary by service provider. l When you are using SIM card 1's data service, SIM card 2's data service will be disabled. Your device's single pass feature helps reduce power consumption and increase your device's standby time. It is not related to your service provider's network conditions. l You can enable call forwarding between SIMs on the device to avoid missed calls. 3 For More Information If you encounter any problems while using your device, you can obtain help from the following resources:

l Visit http://www.hihonor.com to view device information and other information. l Visit http://consumer.huawei.com/en/support for the most up-to-date contact information for your country or region. Go to Settings and touch System > About phone > Legal to view legal information for your product. Go to Settings and touch System > About phone > Legal >

Safety information to view safety information for your product. Go to Settings and touch System > About phone >

Authentication info to view regulatory information for your product. Go to Settings and touch System > Certification logos to view more information on certification logos for your product. All pictures and illustrations in this guide, including but not limited to the device color, size, and display content, are for your reference only. The actual device may vary. Nothing in this guide constitutes a warranty of any kind, express or implied. 4 Safety Information Please read all of the safety information carefully before using your device to ensure its safe and proper operation and to learn how to dispose of your device properly. Operation and safety l l To prevent possible hearing damage, do not listen at high volume levels for long periods. l Using an unapproved or incompatible power adapter, charger, or battery may damage your device, shorten its lifespan, or cause a fire, explosion, or other hazards. Ideal operating temperatures are 0 C to 35 C. Ideal storage temperatures are -20 C to +45 C. l Pacemaker manufacturers recommend that a minimum distance of 15 cm be maintained between a device and a pacemaker to prevent potential interference with the pacemaker. If using a pacemaker, hold the device on the side opposite the pacemaker and do not carry the device in your front pocket. l Keep the device and the battery away from excessive heat and direct sunlight. Do not place them on or in heating devices, such as microwave ovens, stoves, or radiators. l Observe local laws and regulations while using the device. To reduce the risk of accidents, do not use your wireless device while driving. l While flying in an aircraft or immediately before boarding, only use your device according to instructions provided. Use of a wireless device in an aircraft may disrupt wireless networks, present a hazard to aircraft operation, or be illegal. l To prevent damage to your device's parts or internal circuits, do not use it in dusty, smoky, damp, or dirty environments or near magnetic fields. l When charging the device, make sure the power adapter is plugged into a socket near the devices and is easily accessible. l Unplug the charger from electrical outlets and the device when not in use. l Do not use, store or transport the device where flammables or explosives are stored (in a gas station, oil depot, or 5 chemical plant, for example). Using your device in these environments increases the risk of explosion or fire. l Dispose of this device, the battery, and accessories according to local regulations. They should not be disposed of in normal household waste. Improper battery use may lead to fire, explosion, or other hazards. l This device contains a built-in battery. Do not attempt to replace the battery by yourself. Otherwise, the device may not run properly or it may damage the battery. For your personal safety and to ensure that your device runs properly, you are strongly advised to contact a Huawei authorized service center for a replacement. FCC Regulatory Compliance Body worn operation The device complies with RF specifications when used near your ear or at a distance of 1.50 cm from your body. Ensure that the device accessories, such as a device case and device holster, are not composed of metal components. Keep the device away from your body to meet the distance requirement. Certification information (SAR) This device is also designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). The SAR limit adopted by the USA is 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported to the FCC for this device type complies with this limit. The highest SAR value reported to the FCC for this device type when using it at the ear is And when properly worn on the body is And when using the Wi-Fi hotspot function is 0.69 W/kg 0.62 W/kg 0.76 W/kg KSA-LX3 KSA-LX3 KSA-LX3 FCC statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 6 interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Any changes or modifications to this device not expressly approved by Huawei Technologies Co., Ltd. for compliance could void the user's authority to operate the equipment. 7 Legal Notice Trademarks and Permissions

, and are trademarks or registered trademarks of Huawei Technologies Co., Ltd. Android is a trademark of Google Inc. LTE is a trademark of ETSI. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Huawei Technologies Co., Ltd. is under license. Wi-Fi, the Wi-Fi CERTIFIED logo, and the Wi-Fi logo are trademarks of Wi-Fi Alliance. Privacy Policy To better understand how we protect your personal information, please see the privacy policy at http://

consumer.huawei.com/privacy-policy. Copyright Huawei Technologies Co., Ltd. 2019. All rights reserved. THIS DOCUMENT IS FOR INFORMATION PURPOSE ONLY, AND DOES NOT CONSTITUTE ANY KIND OF WARRANTIES. 8 96725611_01

KSA-LX3 Smart Phone Internal Photos of KSA-LX3 2019-4-12 Page 1, Total 5 TUV SUD KSA-LX3 Smart Phone 2019-4-12 Page 2, Total 5 TUV SUD KSA-LX3 Smart Phone 2019-4-12 Page 3, Total 5 TUV SUD KSA-LX3 Smart Phone 2019-4-12 Page 4, Total 5 TUV SUD KSA-LX3 Smart Phone 2019-4-12 Page 5, Total 5 TUV SUD

KSA-LX3 Smart Phone External Photos of KSA-LX3 2019-4-12 Page 1, Total 5 TUV SUD KSA-LX3 Smart Phone 1. Front-KSA-LX3 2019-4-12 Page 2, Total 5 TUV SUD KSA-LX3 Smart Phone 2. Back- KSA-LX3 Page 3, Total 5 2019-4-12 TUV SUD KSA-LX3 Smart Phone 3. Left- KSA-LX3 4. Right- KSA-LX3 5. Top- KSA-LX3 2019-4-12 Page 4, Total 5 TUV SUD KSA-LX3 Smart Phone 6. Bottom- KSA-LX3 2019-4-12 Page 5, Total 5 TUV SUD

KSA-LX3 Smart Phone Label and Label Location:

2019-4-12 Page 1, Total 2 TUV SUD KSA-LX3 Smart Phone 2019-4-12 Page 2, Total 2 TUV SUD

Huawei Technologies Co., Ltd. Federal Communications Commission Oakland Mills Road Columbia MD 21046 2019-09-06 To whom it may concern:

Class 2 Permissive Change Letter Pursuant to section 2.1043,We Huawei Technologies Co., Ltd. Hereby submit a request for class II permissive change to our product, FCC ID: QISKSA-LX3, Grant date: 04/22/2019 Description of the change:

1) LTE B2/B4/B7/B28, WCDMA B2/B4, GSM B2 duplexer Changed 2) Antenna tuner 4SPST changed (pin to pin) 3) Add new vendor earphone Documents Resubmitted:

The following documents from the original application remain unchanged, applicable and representative after Class II Permissive change:

1) All test reports 2) BOM List Sincerely, For and Behalf of:

Huawei Technologies Co., Ltd. Zhang Xinghai EMC Laboratory Manager E-mail: zhangxinghai@huawei.com Tel: 0086-0755-28970299 Fax: 0086-0755-89650226 21_Class 2 Permissive Change Letter V1.0 CTC

Huawei Technologies Co.,Ltd. Federal Communications Commission Oakland Mills Road Columbia MD 21046 To whom it may concern:

Letter of Authorization 2019-08-28 We the undersigned, hereby authorize CTC advanced to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by CTC advanced on our behalf shall have the same affect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from Huawei Technologies Co., Ltd. Sincerely, For and Behalf of:

Huawei Technologies Co., Ltd. Zhang Xinghai EMC Laboratory Manager E-mail: zhangxinghai@huawei.com Tel: 0086-0755-28970299 Fax: 0086-0755-89650226 20_Authorization Letter V1.0 CTC

Huawei Technologies Co.,Ltd. Federal Communications Commission Oakland Mills Road Columbia MD 21046 Subject:

Request for Confidentiality FCC ID:

QISKSA-LX3 To Whom It May Concern:

2019-08-28 Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Operational Description Bom List Tune-Up Procedure Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market.

*****************************************************************************

In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the Commission withholds the following documents from public viewing until 2020-01-26:

External Photos Internal Photos Test Setup Photos User Manual

******************************************************************************

It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. 18_Confidentiality Letter V1.0 CTC Best Regards Zhang Xinghai EMC Laboratory Manager Huawei Technologies Co., Ltd. E-mail: zhangxinghai@huawei.com Tel: 0086-0755-28970299 Fax: 0086-0755-89650226 18_Confidentiality Letter V1.0 CTC

Justification Letter Date (04/22/2019) BABT TCB Balfour House, Churchfield Road, Walton-on-Thames, Surrey, KT12 2TD Dear Sir or Madam, We, Huawei Technologies Co., Ltd. Bantian, Longgang District, Shenzhen, 518129, China hereby to do the original application justification on FCC application: Smart Phone, model: KSA-LX3, FCC ID: QISKSA-LX3 as following:

KSA-LX3 is a smart phone, it supports LTE band 2/4/5/7, WCDMA band 2/4/5, GSM 850/1900 and Bluetooth and 2.4G wifi function. Model: AMN-LX3, FCC ID:QISAMN-LX3 it is a Smart phone which support same frequency bands and function with KSA-LX3 (FCC ID: QISKSA-LX3). And it has been approved on 04/15/2019. The difference between these two FCC IDs KSA-LX3 (FCC ID: QISKSA-LX3) and AMN-LX3(FCC ID:QISAMN-LX3) as below table:

So in this FCC application for Smart Phone, model: KSA-LX3, FCC ID: QISKSA-LX3 New test report R1903H0046-E1 for FCC Part 15B have been submitted, and in this test report the radiated emission test data is new test data, and conducted emission test data was refer form the Part 15B test report R1903H0043-E1 of AMN-LX3(FCC ID:QISAMN-LX3), these test data according to Part 15B are valid and applicable and they are representative of the compliance of KSA-LX3, FCC ID:

QISKSA-LX3 New test report R1903H0046-R5 for FCC Part 15C for Bluetooth (DSS part) have been submitted, all the data were refer form the Part 15C for Bluetooth (DSS part) test report R1903H0043-R5 of AMN-

LX3(FCC ID:QISAMN-LX3), these test data are valid and applicable and they are representative of the compliance of KSA-LX3, FCC ID: QISKSA-LX3 New test report R1903H0046-R6 for FCC Part 15C for BLE (DTS part) have been submitted, all the data were refer form the Part 15C for BLE (DTS part) test report R1903H0043-R6 of AMN-LX3(FCC ID:QISAMN-LX3), these test data are valid and applicable and they are representative of the compliance of KSA-LX3, FCC ID: QISKSA-LX3 New test report R1903H0046-R4 for FCC Part 15C for 2.4G wifi (DTS part) have been submitted, all the data were refer form the Part 15C for BLE (DTS part) test report R1903H0043-R4 of AMN-LX3(FCC ID:QISAMN-LX3), these test data are valid and applicable and they are representative of the compliance of KSA-LX3, FCC ID: QISKSA-LX3 New test report R1903H0046-R1 for FCC Part 22H for GSM850,WCDMA band 5 and LTE band 5 (PCE part) have been submitted, all the data except for radiated spurious emission of GSM 850 were refer form the Part 22H test report R1903H0043-R1 of AMN-LX3(FCC ID:QISAMN-LX3), these test data are valid and applicable and they are representative of the compliance of KSA-LX3, FCC ID: QISKSA-LX3. And only the test data of radiated spurious emission of GSM 850 was new test data for the purpose of verify test result. New test report R1903H0046-R2 for FCC Part 24E for GSM1900,WCDMA band 2 and LTE band 2 (PCE part) have been submitted, all the data were refer form the Part 24E test report R1903H0043-R2 of AMN-LX3(FCC ID:QISAMN-LX3), these test data are valid and applicable and they are representative of the compliance of KSA-LX3, FCC ID: QISKSA-LX3. New test report R1903H0046-R3 for FCC Part 27 for WCDMA band 4 and LTE band 4/7 (PCE part) have been submitted, all the data were refer form the Part 27 test report R1903H0043-R3 of AMN-

LX3(FCC ID:QISAMN-LX3), these test data are valid and applicable and they are representative of the compliance of KSA-LX3, FCC ID: QISKSA-LX3. New SAR test report R1903H0046-S1 have been submitted, in this test report only the worst case of each frequency band and mode were retested and other test data were refer form SAR test report R1903H0043-S1 of AMN-LX3(FCC ID:QISAMN-LX3), these test data are valid and applicable and they are representative of the compliance of KSA-LX3, FCC ID: QISKSA-LX3. Sincerely, For and Behalf of:

Huawei Technologies Co., Ltd. Zhangxinghai EMC Laboratory Manager

Huawei Technologies Co.,Ltd. Federal Communications Commission Oakland Mills Road Columbia MD 21046 2019-04-12 Statement for 2.4G Wi-FiTM QISKSA-LX3 Subject:

FCC ID:

To Whom It May Concern:

We, Huawei Technologies Co., Ltd., states that our productKSA-LX3 comply with the requirement in KDB 594280 D01 Software Configuration Control v02r01. For 2.4G Wi-Fi part, only support channels 1-11, the channel 12 and channel 13 are disabled by software in the factory, this setting is not accessible and cant active by the user or any other third-party. If have any questions concerning the above, please contact the undersigned. Best Regards Zhang Xinghai EMC Laboratory Manager Huawei Technologies Co., Ltd. E-mail: zhangxinghai@huawei.com Tel: 0086-0755-28970299 Fax: 0086-0755-89650226

**Wi-Fi is a trademark of Wi-Fi Alliance 26_2.4G Wi-Fi Declaration Letter V1.0 TUV SUD