FCC ID: QISUAP2105 UMTS Access Point

UAP2105 V300R011C90 User Guide Issue Date 03 2009-08-20 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. For any assistance, please contact our local office or company headquarters. Huawei Technologies Co., Ltd. Address:

Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China http://www.huawei.com support@huawei.com Website:

Email:

Copyright Huawei Technologies Co., Ltd. 2009. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissions and other Huawei trademarks are the property of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders. Notice The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but the statements, information, and recommendations in this document do not constitute a warranty of any kind, express or implied. Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. UAP2105 User Guide Contents Contents About This Document.....................................................................................................................1 1 Changes in the UAP2105 User Guide.....................................................................................1-1 2 Safety Precautions......................................................................................................................2-1 3 Introduction to the UAP2105....................................................................................................3-1 3.1 Appearance of the UAP2105...........................................................................................................................3-2 3.2 LED on the UAP2105.....................................................................................................................................3-2 3.3 Ports and Buttons on the UAP2105.................................................................................................................3-4 3.4 Specifications of the UAP2105.......................................................................................................................3-5 3.4.1 Performance Specifications of the UAP2105.........................................................................................3-5 3.4.2 Technical Specifications of the UAP2105.............................................................................................3-6 4 Installing the UAP2105..............................................................................................................4-1 4.1 Selecting a Position for Installing the UAP2105............................................................................................4-2 4.2 Installing the SIM or USIM Card....................................................................................................................4-2 4.3 Connecting UAP2105 Cables..........................................................................................................................4-3 5 Configuring the UAP2105.........................................................................................................5-1 5.1 Initial Configuration........................................................................................................................................5-2 5.1.1 PPPoE Mode..........................................................................................................................................5-2 5.1.2 FE Direct Connection Mode..................................................................................................................5-4 5.2 Defining a Subscriber in the AHR..................................................................................................................5-5 5.2.1 Adding a Zone........................................................................................................................................5-5 5.2.2 Adding a User.........................................................................................................................................5-7 5.3 Setting Parameters on the AP Manager...........................................................................................................5-9 5.3.1 Activating a Zone...................................................................................................................................5-9 5.3.2 Setting Parameters in a Zone................................................................................................................5-11 6 Routine Operation and Maintenance of the UAP2105........................................................6-1 6.1 Commissioning Services.................................................................................................................................6-2 6.2 Diagnosing Faults............................................................................................................................................6-4 6.3 Handling Alarms.............................................................................................................................................6-5 6.4 Upgrading the Software..................................................................................................................................6-5 6.5 Uploading AP Terminal Files.........................................................................................................................6-8 Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. i Contents UAP2105 User Guide 7 Communication Ports Used by the UAP2105.......................................................................7-1 ii Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide Figures Figures Figure 3-1 UAP2105............................................................................................................................................3-2 Figure 3-2 LED on the UAP2105.........................................................................................................................3-3 Figure 3-3 Ports and buttons on the UAP2105.....................................................................................................3-4 Figure 4-1 Installing the SIM or USIM card........................................................................................................4-3 Figure 4-2 Connecting the power adapter of the UAP2105.................................................................................4-4 Figure 4-3 Cable connections (with the modem having only one LAN port)......................................................4-5 Figure 4-4 Cable connections (with the modem having multiple LAN ports).....................................................4-5 Figure 4-5 Cable connections (in FE direct connection mode)............................................................................4-6 Figure 5-1 Configuring an AP..............................................................................................................................5-3 Figure 5-2 Checking the configuration of the AP................................................................................................5-3 Figure 5-3 FE direct connection mode.................................................................................................................5-4 Figure 5-4 Logging in to the AHR.......................................................................................................................5-5 Figure 5-5 Adding an AP zone.............................................................................................................................5-6 Figure 5-6 Completing settings............................................................................................................................5-6 Figure 5-7 Adding an AP user..............................................................................................................................5-7 Figure 5-8 Logging in to the AP Manager...........................................................................................................5-9 Figure 5-9 Configuring a zone...........................................................................................................................5-10 Figure 5-10 Activating a zone............................................................................................................................5-11 Figure 5-11 Configuring a zone.........................................................................................................................5-12 Figure 5-12 Setting the list of AP frequencies...................................................................................................5-12 Figure 5-13 Setting the list of AP scrambling codes..........................................................................................5-13 Figure 5-14 Configuration confirmation............................................................................................................5-13 Figure 6-1 Tracing management..........................................................................................................................6-3 Figure 6-2 Execute Trouble Diagnose ..............................................................................................................6-4 Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. iii UAP2105 User Guide Tables Tables Table 3-1 LED on the UAP2105..........................................................................................................................3-3 Table 3-2 Ports and buttons on the UAP2105......................................................................................................3-4 Table 3-3 Performance specifications of the UAP2105.......................................................................................3-5 Table 3-4 Technical specifications of the UAP2105............................................................................................3-6 Table 5-1 Meanings of parameters.......................................................................................................................5-7 Table 6-1 Commissioning AP Services................................................................................................................6-2 Table 6-2 Alarm management options.................................................................................................................6-5 Table 7-1 Communication ports used by the UAP2105.......................................................................................7-1 Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. v UAP2105 User Guide Purpose About This Document About This Document This document describes the features, specifications, installation, commissioning, and routine operation and maintenance of Huawei UAP2105 (hereafter referred to as AP). Product Version The following table lists the product version related to this document. Product Version V300R011C90 Product Name UAP2105 Intended Audience This document is intended for:

l l l System engineers Site maintainers Network administrators Change History For changes in the document, see 1 Changes in the UAP2105 User Guide. Organization 1 Changes in the UAP2105 User Guide This describes the changes in the UAP2105 User Guide. 2 Safety Precautions This describes the safety precautions that are taken when installing, operating and maintaining the equipment manufactured by Huawei. 3 Introduction to the UAP2105 Developed in compliance with the protocols of R99/R4/R5/R6 FDD, the UAP2105 provides UMTS radio network access for home and Small Office and Home Office (SOHO) users. Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 1 About This Document UAP2105 User Guide 4 Installing the UAP2105 This describes how to install the UAP2105, accessories, and related cables. 5 Configuring the UAP2105 This describes how to configure the UAP2105 through the WebUI or the AP Manager. 6 Routine Operation and Maintenance of the UAP2105 This describes how to perform commissioning, routine maintenance, and software management of the AP after installation and configuration. 7 Communication Ports Used by the UAP2105 Conventions Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a hazard with a high level of risk, which if not avoided,will result in death or serious injury. Indicates a hazard with a medium or low level of risk, which if not avoided, could result in minor or moderate injury. Indicates a potentially hazardous situation, which if not avoided,could result in equipment damage, data loss, performance degradation, or unexpected results. Indicates a tip that may help you solve a problem or save time. Provides additional information to emphasize or supplement important points of the main text. General Conventions The general conventions that may be found in this document are defined as follows. Convention Times New Roman Boldface Italic Courier New Description Normal paragraphs are in Times New Roman. Names of files, directories, folders, and users are in boldface. For example, log in as user root. Book titles are in italics. Examples of information displayed on the screen are in Courier New. 2 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide About This Document Command Conventions The command conventions that may be found in this document are defined as follows. Convention Boldface Italic

{ x | y | ... }

[ x | y | ... ]

{ x | y | ... }*

[ x | y | ... ]*

Description The keywords of a command line are in boldface. Command arguments are in italics. Items (keywords or arguments) in brackets [ ] are optional. Optional items are grouped in braces and separated by vertical bars. One item is selected. Optional items are grouped in brackets and separated by vertical bars. One item is selected or no item is selected. Optional items are grouped in braces and separated by vertical bars. A minimum of one item or a maximum of all items can be selected. Optional items are grouped in brackets and separated by vertical bars. Several items or no item can be selected. GUI Conventions The GUI conventions that may be found in this document are defined as follows. Convention Boldface

Description Buttons, menus, parameters, tabs, window, and dialog titles are in boldface. For example, click OK. Multi-level menus are in boldface and separated by the ">"

signs. For example, choose File > Create > Folder . Keyboard Operations The keyboard operations that may be found in this document are defined as follows. Format Key Key 1+Key 2 Key 1, Key 2 Description Press the key. For example, press Enter and press Tab. Press the keys concurrently. For example, pressing Ctrl+Alt

+A means the three keys should be pressed concurrently. Press the keys in turn. For example, pressing Alt, A means the two keys should be pressed in turn. Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 3 About This Document UAP2105 User Guide Mouse Operations The mouse operations that may be found in this document are defined as follows. Action Click Double-click Drag Description Select and release the primary mouse button without moving the pointer. Press the primary mouse button twice continuously and quickly without moving the pointer. Press and hold the primary mouse button and move the pointer to a certain position. 4 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide 1 Changes in the UAP2105 User Guide 1 Changes in the UAP2105 User Guide This describes the changes in the UAP2105 User Guide. 03(2009-09-20) This is the second commercial release.. Compared with issue 02(2009-07-10) of V300R011C90, this issue does not add contents. Compared with issue 02(2009-07-10) of V300R011C90, this issue incorporates the following changes:

Topic Logging in to the WebUI Change Description The user name and password for logging in to the WebUI are changed. The description of setting the Internet Explorer 8.0 compatibility is added. Compared with issue 02(2009-07-10) of V300R011C90, this issue does not delete contents. 02(2009-07-10) This is the first commercial release. Compared with issue 01 (2009-05-30) of V300R011C90, this issue does not add contents. Compared with issue 01 (2009-05-30) of V300R011C90, this issue incorporates the following changes:

Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 1-1 1 Changes in the UAP2105 User Guide Topic 3.4.1 Performance Specifications of the UAP2105 UAP2105 User Guide Change Description The description of the capacity and service capabilities of the UAP2105 is modified. Compared with issue 01 (2009-05-30) of V300R011C90, this issue does not delete contents. 01 (2009-05-30) This is the first commercial release. 1-2 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide 2 Safety Precautions 2 Safety Precautions This describes the safety precautions that are taken when installing, operating and maintaining the equipment manufactured by Huawei. Following All Safety Precautions When installing, operating, and maintaining the devices, follow all instructions and precautions on the equipment and in this document for the sake of personal and equipment safety. The indications such as Danger, Caution, and Note in the related documents are additional information. They do not contain all the safety precautions for operations. Complying with the Local Safety Regulations When operating devices, the personnel must comply with the local safety regulations. Installation Requirements The personnel installing and maintaining Huawei products should be trained. Before performing any operation such as device installation and maintenance, the personnel should be familiar with the proper operation methods and safety precautions. l l l l Only trained and qualified personnel are allowed to install, operate, and maintain devices. Only qualified specialists are allowed to check and repair the device and remove the safety facilities. Only personnel that are certificated or authorized by Huawei are allowed to replace or change the device or accessories (including software). Any fault or error that might cause safety problems must be reported to the personnel in charge immediately. Safety of Personnel l l l l Do not perform operation on the device and related cables during thunderstorms. Unplug the device during thunderstorms. Before installing the device and related cables, unplug the device. Take proper safety measures to protect your eyes and respiratory tract against the dust before drilling holes. Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 2-1 2 Safety Precautions Device Safety l Wear gloves before drilling holes. UAP2105 User Guide l l l l Ensure that the device is always kept in a dry environment and is protected against leakage. Leave sufficient space around the device for heat dissipation. Do not block the air vents of the device. Place the device in a dry, ventilated, and dustfree place that is neither exposed to direct sunlight nor close to heat or fire. Keep the device far away from strong magnetic or electric fields. 2-2 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide 3 Introduction to the UAP2105 3 Introduction to the UAP2105 About This Chapter Developed in compliance with the protocols of R99/R4/R5/R6 FDD, the UAP2105 provides UMTS radio network access for home and Small Office and Home Office (SOHO) users. 3.1 Appearance of the UAP2105 The UAP2105 has a case structure. It is elegant, harmonious, and stylish. 3.2 LED on the UAP2105 The UAP2105 has only one LED, which indicates the working status of the UAP2105. 3.3 Ports and Buttons on the UAP2105 This describes the ports and buttons on the UAP2105. The ports are used for the power supply, Ethernet cable, and SIM or USIM card. The RESTORE button is used to restore the login password of the WebUI to the default password. The power switch is used to power on or power off the UAP2105. 3.4 Specifications of the UAP2105 This describes the performance specifications and technical specifications of the UAP2105. Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 3-1 3 Introduction to the UAP2105 UAP2105 User Guide 3.1 Appearance of the UAP2105 The UAP2105 has a case structure. It is elegant, harmonious, and stylish. The UAP2105 is available in black or white. Figure 3-1 shows a black UAP2105. Figure 3-1 UAP2105 3.2 LED on the UAP2105 The UAP2105 has only one LED, which indicates the working status of the UAP2105. Figure 3-2 shows the LED on the UAP2105. 3-2 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide 3 Introduction to the UAP2105 Figure 3-2 LED on the UAP2105 Table 3-1 describes the LED and its status. Table 3-1 LED on the UAP2105 Status ON (red) ON (blue) Description No AP cell is set up, or an alarm of cell setup failure is generated. An AP cell is set up. No service is provided, and no interference exists in the signals of the cell. Blinking in red (ON for 1s and OFF for 1s) Slight interference exists in the signals of an AP cell. The UAP2105 works properly, but the quality of service (QoS) deteriorates. Blinking in red (ON for 0.25s and OFF for 0.25s) Strong interference exists in the signals of an AP cell. The UAP2105 cannot work properly. Blinking in blue (ON for 1s and OFF for 1s) An AP cell is set up successfully, and services are being provided in the cell. Software is being downloaded, or the system is being upgraded. Blinking in blue (ON for 0.125s and OFF for 0.125s) Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 3-3 3 Introduction to the UAP2105 UAP2105 User Guide 3.3 Ports and Buttons on the UAP2105 This describes the ports and buttons on the UAP2105. The ports are used for the power supply, Ethernet cable, and SIM or USIM card. The RESTORE button is used to restore the login password of the WebUI to the default password. The power switch is used to power on or power off the UAP2105. Figure 3-3 shows the ports and buttons on the panel of the UAP2105. Figure 3-3 Ports and buttons on the UAP2105 Table 3-2 describes the ports and buttons on the UAP2105. Table 3-2 Ports and buttons on the UAP2105 Port or Button RESTORE Description Button for restoring the login password of the WebUI. After you press the button for five seconds, Restore the AP to factory settings

(including the IP address for AP local maintenance and the user name and password for logging in to the WebUI). SIM SIM or USIM card holder, which is used for housing the SIM or USIM card 3-4 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide 3 Introduction to the UAP2105 Port or Button LAN Description Ethernet port for an Ethernet cable PWR Power socket, which is connected to the 12 V DC power adapter Power switch Used to power on or power off the UAP2105 3.4 Specifications of the UAP2105 This describes the performance specifications and technical specifications of the UAP2105. 3.4.1 Performance Specifications of the UAP2105 This describes the performance specifications of the UAP2105 in terms of the frequency bands, maximum transmit power, number of TRXs, transmit and receive diversity, receiver sensitivity, and clock precision. 3.4.2 Technical Specifications of the UAP2105 This describes the technical specifications of the UAP2105. 3.4.1 Performance Specifications of the UAP2105 This describes the performance specifications of the UAP2105 in terms of the frequency bands, maximum transmit power, number of TRXs, transmit and receive diversity, receiver sensitivity, and clock precision. Performance Specifications Table 3-3 Performance specifications of the UAP2105 Item Frequency bands Specification Frequency band RX band (MHz) BAND I (2100 MHz) 1920 to 1980 Band II (1900 MHz) 1850 to 1910 Band V (850 MHz) 824 to 849 13 dBm (20 mW) Maximum transmit power Capacity TX band (MHz) 2110 to 2170 1930 to 1990 869 to 894 Only one TRX is supported. Only one cell is supported. A maximum of 20 UL channel elements (CEs) and 20 DL CEs is supported. Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 3-5 3 Introduction to the UAP2105 Item Service capabilities Transmit and receive diversity Receiver sensitivity UAP2105 User Guide Specification Common PS and CS services:

l A maximum of four concurrent AMR services is supported. l A maximum of four concurrent VP services is supported. l A maximum of eight concurrent PS services is supported. l A maximum of four concurrent R99 384 kbit/s PS services is supported. l A maximum of four concurrent CS users is supported. l A maximum of four concurrent PS users is supported. HSDPA service:

l The maximum supported HSDPA rate is 3.6 Mbit/s or 7.2 Mbit/s. The default value is 3.6 Mbit/s. The license can be used to control the maximum HSDPA rate of the UAP2105. l 3GPP R99, R4, R5, and R6 services can be provided at the same time. l A maximum of four concurrent HSDPA users is supported. l A maximum of 10 HS-PDSCH codes is supported. HSUPA service l The maximum supported HSUPA rate is 1.44 Mbit/s. l 3GPP R99, R4, R5, and R6 services can be provided at the same time. l A maximum of four concurrent HSUPA users is supported. l The 10 ms Transmission Time Interval (TTI) over the E-DCH is supported. No transmit diversity or receive diversity

-110 dBm Clock precision 0.1 ppm 3.4.2 Technical Specifications of the UAP2105 This describes the technical specifications of the UAP2105. Technical Specifications Table 3-4 Technical specifications of the UAP2105 Item Dimensions (Height x Width x Depth) Specification 33 mm x 125 mm x 125 mm Weight 0.4 kg 3-6 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide Item Power consumption Ambient temperature 3 Introduction to the UAP2105 Specification

< 8 W Working temperature: -5oC to +40oC Storage temperature: -40oC to +70oC Relative humidity 5% RH to 95% RH Specifications of the power adapter Input voltage: 90 V AC to 264 V AC Frequency range: 47 Hz to 63 Hz Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 3-7 UAP2105 User Guide 4 Installing the UAP2105 4 Installing the UAP2105 About This Chapter This describes how to install the UAP2105, accessories, and related cables. 4.1 Selecting a Position for Installing the UAP2105 This describes the requirements for the installation position of the UAP2105. 4.2 Installing the SIM or USIM Card This describes how to install the SIM or USIM card. The data in the card enables the UAP2105 to perform user authentication and then to connect the core network after the authentication is successful. 4.3 Connecting UAP2105 Cables This describes how to connect the power adapter of the UAP2105 and how to connect the Ethernet cable based on the network topology of the UAP2105. Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 4-1 4 Installing the UAP2105 UAP2105 User Guide 4.1 Selecting a Position for Installing the UAP2105 This describes the requirements for the installation position of the UAP2105. Requirements for the Installation Position l The UAP2105, a home device, is installed indoor areas that are away from children, such as living rooms or studies. It supports the tabletop or wall-mounted installation. The UAP2105 mounted on a wall obtatains better coverage than that placed on a tabletop. Leave a minimum of 20 cm space around the UAP2105 for heat dissipation. When selecting a position for installing the UAP2105, adhere to the following rules:

Do not place the AP near the window. Do not cover or block the AP. Do not overload the AP. Do not place AP near a microwave oven. Do not place the AP on an electrical device. Do not directly blow hot wind to the AP. l l l l l 4.2 Installing the SIM or USIM Card This describes how to install the SIM or USIM card. The data in the card enables the UAP2105 to perform user authentication and then to connect the core network after the authentication is successful. Prerequisite Procedure Before installing the SIM or USIM card, power off the UAP2105 and disconnect the power cable. Step 1 Insert the SIM or USIM card into the card holder, as shown in Figure 4-1. 4-2 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide 4 Installing the UAP2105 Figure 4-1 Installing the SIM or USIM card CAUTION l While inserting the SIM or USIM card into the card holder, ensure that the notch on the SIM or USIM card faces the silkscreen. l Do not remove the SIM or USIM card while the UAP2105 is running. Otherwise, the AP cell cannot be set up. After the SIM or USIM card is re-inserted, the UAP2105 cell is reestablished.

----End 4.3 Connecting UAP2105 Cables This describes how to connect the power adapter of the UAP2105 and how to connect the Ethernet cable based on the network topology of the UAP2105. Context A power adapter and straight-through cable are delivered with the UAP2105 and are placed in the external packing box. Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 4-3 4 Installing the UAP2105 Procedure Step 1 Connect the power adapter, as shown in Figure 4-2. Figure 4-2 Connecting the power adapter of the UAP2105 UAP2105 User Guide CAUTION To ensure that the UAP2105 runs properly, use the power adapter delivered with the UAP2105. Step 2 Connect the Ethernet cable. l In PPPoE mode The UAP2105 is connected to the Ethernet through an xDSL device, such as a modem, BAS, or DSLAM. If the Modem has ... Only one LAN port Then 1. Use Ethernet cables to connect the UAP2105 and the computer for local maintenance to idle LAN ports on a router or switch. 2. Connect the router or switch to a modem. For details on connections, see the documents delivered with the router or switch. Figure 4-3 shows the cable connections when the modem has only one LAN port. NOTE If no router is configured, you can directly connect the computer for local maintenance to the modem to configure the modem, and then connect the computer to the UAP2105 to configure the UAP2105. After the modem and the UAP2105 are configured, you can directly connect the UAP2105 to the LAN port on the modem. 4-4 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide 4 Installing the UAP2105 If the Modem has ... Multiple LAN ports Then Connect the UAP2105 to an idle LAN port on the modem through an Ethernet cable, as shown in Figure 4-4. The UAP2105 and the computer for local maintenance should be connected to the same modem. Figure 4-3 Cable connections (with the modem having only one LAN port) Figure 4-4 Cable connections (with the modem having multiple LAN ports) CAUTION If a cable modem is used (Cable Modem is labeled on the housing of the modem), connect the cables according to the documents delivered with the cable modem. l In FE direct connection mode Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 4-5 4 Installing the UAP2105 UAP2105 User Guide The UAP2105 is directly connected to the Ethernet through a device, such as a router. The number of devices used in FE direct connection mode is smaller than the number of devices used in PPPoE mode. As a result, the UAP2105 provides higher uplink and downlink rates. 1. Connect the UAP2105 to an idle LAN port on the router through an Ethernet cable. The UAP2105 and the computer for local maintenance should be connected to the same router. 2. Connect the router to the Ethernet. For details on connections, see the documents delivered with the router. Figure 4-5 shows the cable connections in FE direct connection mode. Figure 4-5 Cable connections (in FE direct connection mode) Step 3 Check the cables to ensure that all connections are secure.

----End 4-6 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide 5 Configuring the UAP2105 5 Configuring the UAP2105 About This Chapter This describes how to configure the UAP2105 through the WebUI or the AP Manager. 5.1 Initial Configuration This describes how to configure the IP address of the AP and the connection mode through an ADSL modem or router according to the network topology of the AP. 5.2 Defining a Subscriber in the AHR This describes how to define an AP subscriber in the AHR. To define an AP subscriber in the AHR, create an AP zone, and then add an AP user to the zone. 5.3 Setting Parameters on the AP Manager This describes how to set AP parameters on the AP Manager. The parameter settings are applicable to all APs managed by the AP Manager. Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 5-1 5 Configuring the UAP2105 5.1 Initial Configuration UAP2105 User Guide This describes how to configure the IP address of the AP and the connection mode through an ADSL modem or router according to the network topology of the AP. 5.1.1 PPPoE Mode The PPPoE mode consists of PPPoE bridge mode and PPPoE route mode. Regardless of the mode you choose, you need to set the parameters of the ADSL modem and the AP. 5.1.2 FE Direct Connection Mode This describes how to configure the IP address of the AP and the connection of the router in FE direct connection mode. 5.1.1 PPPoE Mode The PPPoE mode consists of PPPoE bridge mode and PPPoE route mode. Regardless of the mode you choose, you need to set the parameters of the ADSL modem and the AP. Prerequisite Context l l You have logged in to the WebUI. For details, see Logging in to the WebUI. The IP address of the computer is set on the 192.168.1.x network segment. In PPPoE bridge mode l The connection mode when an ADSL modem works in bridge mode and the application type of the modem is set to Bridge Only is called PPPoE bridge mode. In PPPoE bridge mode, you need to enter the user name and password of each terminal connected to the modem to initiate PPPoE dial-up connections for authentication. In PPPoE route mode l The modem obtains the IP address and related information such as the IP address of the gateway and subnet mask from the BAS through PPPoE dial-up connections. After the modem passes the authentication, it is connected to Internet. In PPPoE route mode, the modem works in DHCP Server mode. Each terminal connected to the modem can automatically obtain the IP address of the LAN from the modem without PPPoE dial-up connections. Procedure l In PPPoE bridge mode 1. Configure the ADSL modem. NOTE To set WAN Configuration of the ADSL modem in PPPoE bridge mode, set the application type of the ADSL modem to Bridge Only and the connection of the ADSL modem to RFC 2684 Bridge. The setting method varies according to the type of the ADSL modem. For details, see the document delivered with the ADSL modem. 5-2 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide 5 Configuring the UAP2105 2. Configure the AP. On the WebUI, choose Transfer Basic > NETMODE . Click Mod, set Net Mode to PPPOELINK, and then type the user name and password for a PPPoE dial-up connection, as shown in Figure 5-1. Figure 5-1 Configuring an AP NOTE After the networking mode of the AP is changed, the AP is automatically restarted. The existing configurations are not modified. l In PPPoE route mode 1. Configure the ADSL modem. NOTE To set WAN Configuration, NAT, and DNS of the ADSL modem in PPPoE route mode, set the application type of the ADSL modem to PPPoE, NAT to NAPT, DNS to Allow, and DHCP to DHCP Server. The setting method varies according to the type of the ADSL modem. For details, see the document delivered with the ADSL modem. 2. Check the configuration of the AP. On the WebUI, choose Transfer Basic >

NETMODE to check the configuration of the AP, as shown in Figure 5-2. Figure 5-2 Checking the configuration of the AP Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 5-3 5 Configuring the UAP2105 UAP2105 User Guide If ... Net Mode is set to ETHIP and AUTO IP to ENABLE Then The configuration is complete. End the operation. NOTE When an AP is delivered, Net Mode is set to ETHIP and AUTO IP to ENABLE by default. Therefore, in PPPoE route mode, it is not necessary to configure the AP. Net Mode is not set to ETHIP or AUTO IP to ENABLE Go to 3. 3. Configure the AP. On the WebUI, choose Transfer Basic > NETMODE . Click Mod and set Net Mode to ETHIP and AUTO IP to ENABLE.0

----End 5.1.2 FE Direct Connection Mode This describes how to configure the IP address of the AP and the connection of the router in FE direct connection mode. l l You have logged in to the WebUI. For details, see Logging in to the WebUI. The IP address of the computer is set on the 192.168.1.x network segment. Prerequisite Context Figure 5-3 shows the FE direct connection mode. Figure 5-3 FE direct connection mode 5-4 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide Procedure 5 Configuring the UAP2105 Step 1 For details, see the description of PPPoE route mode in 5.1.1 PPPoE Mode. NOTE The method of setting the router in FE direct connection mode is the same as the method of setting the ADSL modem in PPPoE route mode.

----End 5.2 Defining a Subscriber in the AHR This describes how to define an AP subscriber in the AHR. To define an AP subscriber in the AHR, create an AP zone, and then add an AP user to the zone. 5.2.1 Adding a Zone This describes how to add an AP zone in the AHR. Before adding an AP zone, obtain the information about neighboring macro cells around the AP cell and the IP addresses of the AP Manager, AG, SeGW, and CLK used in the AP network. 5.2.2 Adding a User This describes how to perform AP user management in the AHR, for example, add an AP user in the AHR. 5.2.1 Adding a Zone This describes how to add an AP zone in the AHR. Before adding an AP zone, obtain the information about neighboring macro cells around the AP cell and the IP addresses of the AP Manager, AG, SeGW, and CLK used in the AP network. Prerequisite Procedure l l You have installed the AHR client that matches the version of the AHR server. You have obtained the IMSI of the SIM or USIM card used in the AP and the IP addresses of the AP Manager, AG, SeGW, and CLK used in the AP network. Step 1 Start the AHR client, and then type the user name, password, and IP address of the AHR server, as shown in Figure 5-4. Figure 5-4 Logging in to the AHR Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 5-5 5 Configuring the UAP2105 UAP2105 User Guide Step 2 Choose Area > AP Zone Management. The Zone Configuration page is displayed. Step 3 Click Add. The Add AP Zone dialog box is displayed, as shown in Figure 5-5. Figure 5-5 Adding an AP zone Step 4 Type the zone where the AP is located and set SCTP Port to the port ID that is the same as the port ID of the AG. Step 5 Click Next to set the IP addresses of the AP Manager, AG, SeGW, and CLK and the information about neighboring macro cells around the AP cell in sequence. Step 6 Confirm the settings, and then click Finish, as shown in Figure 5-6. Figure 5-6 Completing settings 5-6 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide

----End 5.2.2 Adding a User 5 Configuring the UAP2105 This describes how to perform AP user management in the AHR, for example, add an AP user in the AHR. Procedure Step 1 Choose Service > AP User Management. The AP User Management page is displayed. Step 2 Click OK. The Add AP User page is displayed, as shown in Figure 5-7. Figure 5-7 Adding an AP user Table 5-1 describes the parameters. Table 5-1 Meanings of parameters Parameter IMSI AP Zone Name Input Value IMSI of the SIM or USIM card used in the AP Description

Name of the zone configured in the 5.2.1 Adding a Zone Name of the zone where the AP is located Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 5-7 5 Configuring the UAP2105 Parameter Location Detect Mode Input Value Cell ID PLMNID IP Address None Close Open User Access Policy PLMNID Display Information about the operator that provides services SMS Content SMS content for location indication UAP2105 User Guide Description Location detection is performed according to the macro cell reported by the AP. The location detection is used to check the validity of the AP. Location detection is performed according to the PLMN ID reported by the AP. Location detection is performed according to the IP address reported by the AP. No location detection is performed for the AP. Only the UEs in the UE permission list set in the AHR can connect to the AP network. All UEs under the AP coverage can connect to the AP network. When the PLMNID Display switch is enabled on the AP Manager and a UE camps on the AP cell, the information about the operator is displayed on the UE. When the SMS Content switch is enabled on the AP Manager and a UE camps on the AP cell, a message containing the location indication information is sent to the UE. Step 3 Type parameters (the parameters with red asterisks are mandatory), and then click OK. The AP user is added successfully.

----End 5-8 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide 5 Configuring the UAP2105 5.3 Setting Parameters on the AP Manager This describes how to set AP parameters on the AP Manager. The parameter settings are applicable to all APs managed by the AP Manager. 5.3.1 Activating a Zone Before setting the parameters in a zone on the AP Manager, activate the zone. 5.3.2 Setting Parameters in a Zone Select the zone in which parameters need to be set, and then set the APCELLAC, list of AP frequencies, and list of AP scrambling codes. 5.3.1 Activating a Zone Before setting the parameters in a zone on the AP Manager, activate the zone. Prerequisite Procedure l l l You have obtained the IP address, login user name, and password of the AP Manager. You have obtained the Mobile Network Code (MNC), Mobile Country Code (MCC), Air Mobile Country Code (MCCAIR), Air Mobile Network Code (MNCAIR), and Air Location Area Code Range (LACAIR) used by the AP. You have obtained the APCELLAC, list of frequencies, and list of scrambling codes in the zone where the AP is located. Step 1 Open the Internet Explorer (IE), and then type the IP address and login port number (such as, http://185.22.61.79:8080/apm) of the AP Manager. The login dialog box is displayed, as shown in Figure 5-8. Figure 5-8 Logging in to the AP Manager Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 5-9 5 Configuring the UAP2105 UAP2105 User Guide Step 2 Type the user name, password, and verify code to log in to the AP Manager. NOTE The default user name is admin, and the default password is 11111111. Step 3 Choose Configuration > Zone Configuration. The Zone Configuration page is displayed. Step 4 Select the zone in which parameters need to be set, as shown in Figure 5-9. Then, click Activate. Figure 5-9 Configuring a zone Step 5 Set the parameters based on network planning, and then click Activate to activate the zone, as shown in Figure 5-10. 5-10 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide Figure 5-10 Activating a zone 5 Configuring the UAP2105

----End 5.3.2 Setting Parameters in a Zone Select the zone in which parameters need to be set, and then set the APCELLAC, list of AP frequencies, and list of AP scrambling codes. Prerequisite Procedure The zone has been activated. Step 1 Choose Configuration > > Zone Configuration . The Zone Configuration page is displayed. Step 2 Select the zone in which parameters need to be set, as shown in Figure 5-11. Then, click Configure. Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 5-11 5 Configuring the UAP2105 Figure 5-11 Configuring a zone UAP2105 User Guide Step 3 Select the target AP in the zone, and then click Next. Step 4 Choose APCELLFREQ from the left pane and set the list of AP frequencies, as shown in Figure 5-12. Figure 5-12 Setting the list of AP frequencies 5-12 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide 5 Configuring the UAP2105 NOTE Click Add Configuration to add a frequency of the AP. Step 5 After completing the settings, click Confirm. Step 6 Choose APPSCODE from the left pane and set the list of AP scrambling codes, as shown in Figure 5-13. Figure 5-13 Setting the list of AP scrambling codes NOTE Click Add Configuration to add a frequency of the AP. Step 7 After completing the settings, click Confirm. Step 8 Choose APCELLAC from the left pane and set the APCELLAC of the AP. Step 9 After completing the settings, click Confirm. Step 10 Click Submit after the APCELLAC, list of AP frequencies, and list of AP scrambling codes are set. The configuration confirmation page is displayed, as shown in Figure 5-14. Figure 5-14 Configuration confirmation Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 5-13 5 Configuring the UAP2105 Step 11 After confirming the settings, click Apply.

----End UAP2105 User Guide 5-14 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide 6 Routine Operation and Maintenance of the UAP2105 6 Routine Operation and Maintenance of the UAP2105 About This Chapter This describes how to perform commissioning, routine maintenance, and software management of the AP after installation and configuration. 6.1 Commissioning Services This describes how to trace the Uu interface, Iu interface, and CDT messages to test the services offered by the AP through the Trace Viewer tool of the Local Maintenance Terminal (LMT). 6.2 Diagnosing Faults This describes how to diagnose the faults in the AP, faults at the radio network layer, and faults at the transport network layer on the WebUI and how to view diagnosis results. 6.3 Handling Alarms This describes how to manage AP alarms on the AP Manager. You can subscribe to alarms, query alarm logs, and query and monitor active alarms. 6.4 Upgrading the Software This describes how to upgrade the AP software on the FTP server. 6.5 Uploading AP Terminal Files This describes how to upload the AP log, configuration file, and performance file to the FTP server through the AP Manager for future analysis, use, or query. Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 6-1 6 Routine Operation and Maintenance of the UAP2105 UAP2105 User Guide 6.1 Commissioning Services This describes how to trace the Uu interface, Iu interface, and CDT messages to test the services offered by the AP through the Trace Viewer tool of the Local Maintenance Terminal (LMT). Prerequisite Context l l l l l l The AP is powered on, and the AP cell is set up. Two functional UEs, UE 1 and UE 2, are ready. If the admission mode of the AP is set to Close or Group, the IMSIs of UE 1 and UE 2 are added to the AP permission list. For details about how to configure the AP permission list, see the AHR Operator Guide. A functional fixed-line phone is ready. The LMT that matches the AP version works properly. The CS and PS domains are functional. Table 6-1 describes the basic tasks involved in service commissioning. Table 6-1 Commissioning AP Services Task Test voice call services. Method UE 1 or UE 2 originates a voice call to the fixed-line phone. Expected Result The voice quality is good without loud noise. UE 1 originates a voice call to UE 2. The voice quality is good without loud noise. Test video call services. UE 1 originates a video call to UE 2. Test PS services. Browse web pages and upload or download data through a UE. l The voice is clear. l The video is clear and fluent. l The voice is synchronized with the video. Web pages are browsed normally, and data is uploaded or downloaded successfully within the specified time. Procedure Step 1 Log in to the LMT, and then choose Service > Trace Management > Interface Trace Task to trace the Uu interface, Iu interface, and CDT messages, as shown in Figure 6-1. 6-2 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide 6 Routine Operation and Maintenance of the UAP2105 Figure 6-1 Tracing management Step 2 Power on the UE under the coverage of the AP cell. Check whether the UE can automatically search for the AP cell during startup. If ... Then The UE fails to search for the AP cell 1. Identify and rectify the fault. For details, see Failure of the UE to Search for the AP Cell. 2. Go to Step 3. The UE succeeds in searching for the AP cell Go to Step 3. Step 3 Wait until the UE is under the coverage of the AP cell and the location update is complete. If the AP fails to access the AP cell, identify and rectify the faulty. For details, see Failure of the UE to Access the AP Cell. Step 4 Test the services provided by the AP. 1. A UE originates a voice call to the fixed-line phone. 2. UE 1 originates a voice call to UE 2. 3. UE 1 originates a video call to UE 2. 4. Browse web pages and upload or download data through a UE.

----End Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 6-3 6 Routine Operation and Maintenance of the UAP2105 UAP2105 User Guide 6.2 Diagnosing Faults This describes how to diagnose the faults in the AP, faults at the radio network layer, and faults at the transport network layer on the WebUI and how to view diagnosis results. Procedure Step 1 Log in to the WebUI. For details, see Logging in to the WebUI. Then, choose TroubleDiagnose. The Execute Trouble Diagnose page is displayed, as shown in Figure 6-2. Figure 6-2 Execute Trouble Diagnose Step 2 Set Diagnose Mode and determine the type of a fault. l Equipment Trouble Diagnose: indicates the faults in the AP. l Wireless Trouble Diagnose: indicates the faults at the radio network layer. l transfers Trouble Diagnose: indicates the faults at the transport network layer. Step 3 Set OutPut Mode and determine the output mode of the fault diagnosis result. l Just Show Abnormity Result: indicates that only fault diagnosis results are displayed. l Show All Result: indicates that all diagnosis results are displayed. 6-4 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide 6 Routine Operation and Maintenance of the UAP2105 Step 4 Click Start to diagnose the faults. After the fault diagnosis is complete, diagnosis results are displayed in the Trouble Diagnose Log pane.

----End 6.3 Handling Alarms This describes how to manage AP alarms on the AP Manager. You can subscribe to alarms, query alarm logs, and query and monitor active alarms. Procedure Step 1 Log in to the AP Manager, and then click the Fault tab. On the tab page, manage alarms. Table 6-2 describes alarm management options. Table 6-2 Alarm management options Alarm Management Option Alarm Subscribe Active Alarm Monitor Active Alarm Query Alarm Log Query Terminal Alarm Log Query

----End Description Subscribe to the alarms of an AP or maintain the list of the APs that have subscribed to alarms. Active Alarm Monitor, Active Alarm Query, and Alarm Log Query are available for only the APs that subscribe to alarms. View the active alarms that are not cleared in real time and delete the cleared active alarms. Query the active alarms reported to the AP Manager database by the AP. To query the detailed information about an alarm, click on the left of the alarm. Query the alarm logs reported to the AP Manager database by the AP. Query the remaining alarm logs on the AP. If the AP is offline, the AP Manager prompts operation timeout. 6.4 Upgrading the Software This describes how to upgrade the AP software on the FTP server. Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 6-5 Available Unavailable l l l 6 Routine Operation and Maintenance of the UAP2105 Prerequisite UAP2105 User Guide The FTP server is available. Log in to the AP Manager, and then choose Software > File Server. On the File Servers tab page, check Status of the corresponding FTP server. If Status of the FTP Server is ... Then The AP Manager communicates with the FTP server normally. The AP Manager cannot communicate with the FTP server normally. l Select the option button before the FTP server, and then click Modify. Configure the FTP server on the displayed File Server Information page. The target upgrade version of the AP is synchronized to the FTP server. Log in to the AP Manager, and then choose Software. Choose File Server, and then query the version file of the FTP server on the File Servers and Versions tab page. Choose Version, and then click Add to upload the version file. After the version file is uploaded successfully, the AP Manager synchronizes the file to the available FTP server automatically. The zone where the AP is located is in the zone list of the FTP server. Log in to the AP Manager, and then choose Software > File Server. Select the FTP server on the File Servers tab page, and then query the zone list of the file server in the File Server Information dialog box. Configure the mapping between the zone and the FTP server on the Zone Servers Configuration tab page. Procedure l Upgrading a single AP 1. 2. 3. Log in to the AP Manager, and then choose Software > Upgrade. In the Terminal List pane, select the AP to be upgraded, and then click Upgrade. The Terminal Upgrade page is displayed. On the page, set options related to the upgrade task. Option Upgrade Version Description It refers to the target version that the AP software is upgraded to. Immediately Reboot It enables you to determine whether the AP is rebooted immediately after the software is downloaded successfully. 4. Click Submit to complete the settings. 6-6 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide 6 Routine Operation and Maintenance of the UAP2105 If You Set Immediately Reboot to ... Then Yes The AP is rebooted immediately for upgrade after the software is downloaded successfully. NOTE Rebooting the AP disrupts the services provided by the AP. No After the software is downloaded successfully, check whether services are provided, and then reboot the AP. l If no service is provided, reboot the AP for upgrade immediately. l If services are ongoing, reboot the AP for upgrade after services are performed. l Upgrading APs in batches 1. 2. Log in to the AP Manager, and then choose Software > Batch Upgrade. The Task Information page is displayed. On the page, set options related to the upgrade task. Option Target Version Description It refers to the target version that the AP software is upgraded to. Immediately Reboot Allow Retry Triggering Mode Valid Time It enables you to determine whether the AP is rebooted immediately after the software is downloaded successfully. It enables you to determine whether the software is upgraded again when sending an upgrade command fails. It refers to the triggering mode for upgrading the software. Options:

l Timer: indicates that you can specify the time for performing the upgrade. l Immediately: indicates that the software is upgraded immediately. l Manual: indicates that the software is upgraded manually. It refers to the validity period of an upgrade task. If the validity period expires, the software is not upgraded again even if the upgrade fails. If the upgrade mode is set to Timer, this option is enabled. Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 6-7 6 Routine Operation and Maintenance of the UAP2105 UAP2105 User Guide Option Time Setting Description It is used to specify the time for starting the upgrade. If the upgrade mode is set to Timer, this option is enabled. 3. Click Next. On the displayed page, select the target APs. You can select the target APs on the AP Manager in the following two ways:

Special Terminal: indicates that you directly select APs to be upgraded. Special Condition: indicates that you select APs to be upgraded by special conditions. 4. Click Submit to complete the settings. If You Set Immediately Reboot to ... Then Yes The AP is rebooted immediately for upgrade after the software is downloaded successfully. NOTE Rebooting the AP disrupts the services provided by the AP. No

----End After the software is downloaded successfully, check whether services are provided, and then reboot the AP. l If no service is provided, reboot the AP for upgrade immediately. l If services are ongoing, reboot the AP for upgrade after services are performed. 6.5 Uploading AP Terminal Files This describes how to upload the AP log, configuration file, and performance file to the FTP server through the AP Manager for future analysis, use, or query. Prerequisite The FTP server is available. Log in to the AP Manager, and then choose Software > File Server. On the File Servers tab page, check Status of the corresponding FTP server. If Status of the FTP Server is ... Available Then The AP Manager communicates with the FTP server normally. 6-8 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide 6 Routine Operation and Maintenance of the UAP2105 If Status of the FTP Server is ... Unavailable Then The AP Manager cannot communicate with the FTP server normally. l Select the option button before the FTP server, and then click Modify. Configure the FTP server on the displayed File Server Information page. Procedure Step 1 Log in to the AP Manager, choose Fault > Terminal Files, and then click Uploading Files. Step 2 The Uploading Files page is displayed. On the page, type the APEI of the AP whose terminal files need to be uploaded in the Serial NO. box and select a target file from the File Type drop-

down list. The types of the AP terminal files to be uploaded are as follows:

l Configuration File l Performance File l Alarm Log Alarm logs consist of CurrUserAlm.log, HisUserAlm.log, and OrigAlm.log. The AP saves a maximum of 10,000 OrigAlm.log entries, 50 CurrUserAlm.log entries, and 1,000 HisUserAlm.log entries. After the number of saved entries reaches the threshold, the earliest entries are deleted so that follow-up entries can be saved. l Running Log The AP saves a maximum of 2,000 running log entries. After the number of saved entries reaches 2,000, the earliest entries are deleted so that follow-up entries can be saved. l Core Log The latest three core log entries for abnormal resetting of the AP are saved. Step 3 Click Uploading Files to upload the specified terminal files of the AP. If ... View Files is displayed View Files is not displayed, or a message box is displayed Then Click View Files. In the File List pane, Status indicates the uploading status of the file. The connection to the FTP server through the AP Manager is faulty. Choose System > System Setting >

Fault, and then reset the login information of the FTP server. Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 6-9 6 Routine Operation and Maintenance of the UAP2105 UAP2105 User Guide NOTE To view terminal files, click View Files, and store the terminal files on the local disk of the computer according to the displayed system message. The methods of viewing terminal files are the same. Choose Start > All Programs > Huawei Local Maintenance Terminal, and then select the corresponding alarm browser tool. The following description takes the method of viewing alarm logs for example:

1. Choose Start > All Programs > Huawei Local Maintenance Terminal > Alarmlog Browser Tool. 2. Select the AP type and language type. 3. Click OK. 4. Select the alarm log to be viewed, and then click Open.

----End 6-10 Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. Issue 03 (2009-08-20) UAP2105 User Guide 7 Communication Ports Used by the UAP2105 7 Communication Ports Used by the UAP2105 Table 7-1 lists the communication ports used by the UAP2105. Port Num ber at Side A

(RX) 80 Table 7-1 Communication ports used by the UAP2105 Prot ocol Side A Side B Service Port Number at Side B

(TX) Rights Control TCP UAP2 105 TCP UAP2 105 6000 TCP UAP2 105 6006 WebUI 1024-6553 5 LMT, WebUI Proxy LMT, WebUI Proxy 1024-6553 5 1024-6553 5 WebUI port for local OM User name and password MML port for local OM User name and password Binary port for local OM User name and password TCP UAP2 105 TCP UAP2 105 TCP UAP2 105 7547 AP Manager 1024-6553 5 TR-069 protocol port 500 SeGW 4500 SeGW 1024-6553 5 Default IKE port of the IPSec 1024-6553 5 NAT protocol port of the IPSec TCP UAP2 105 3300 3 CLK Server 1024-6553 5 Clock synchronization

Issue 03 (2009-08-20) Huawei Proprietary and Confidential Copyright Huawei Technologies Co., Ltd. 7-1