165MM Clip Clap 2 Bluetooth Speaker Instruction Manual 7197-64 1 2 3 4 M M 9 8 Functions:
1. 2. 3. 4. Clip ON/OFF Switch LED Indicator Type-C USB Port Whats included:
1 x Bluetooth Speaker (7197-64) 1 x USB to Type-C Charging Cable 1 x Instruction Manual Battery Capacity: 3.7V, 1.11Wh, 300mAh Playback time: 1.5 hours at max volume Charging time: up to 1.5 hours Pairing name: Clip Clap 2 Bluetooth version: 5.0 Speaker driver size: 13X12.5MM Rated output power: 2W Range: 10M Impedance:4 Frequency response:150 Hz ~ 15 K Hz Signal noise ratio: 75db3 Input voltage: DC5V 250mA Instructions:
(Be sure to fully charge the speaker before 1. 2. Charging the Speaker Connect the provided charging cable to a power source and to the Type-C USB port on the speaker (4). The LED indicator light will glow red when charging and turn off when fully charged. Bluetooth Setup:
Press and hold ON/OFF button to turn RED&BLUE when in pairing mode. Turn ON the Bluetooth function on mobile device, select Clip Clap 2 pairing name. If the devices have successfully paired, the
3. Speaker will automatically pair if the mobile device has been paired before. When the bluetooth is disconnected, the speaker will automatically shut-off after 3 mins. Press and hold the ON/OFF button to turn OFF the speaker. Play and Calling Controls:
When playing music, short press ON/OFF button to pause/resume music. When theres an incoming call, short press ON/OFF button answer the call and press again to end the call Press and hold the button to reject the call. SAFETY PRECAUTIONS:
WARNING-When using this product, basic precautions should always be followed:
Read all the instructions before use. Never store or use this product in temperatures below 32F (0C) or above 115F (45C). The unit will only achieve full performance 1. 2. 3. after 2 or 3 completed charge and discharge cycles. To reduce the risk of injury, close supervision is required when the product is used near children. Do not expose the device to moisture. Do not use the device in excess of its output rating. Overloaded outputs above the rating may 4. 5. 6. 7. FCC Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Warning:
(1)
(2)
8. Do not use the device if it has been 9. explosion or risk of injury. Do not disassemble the device. For 10. professional. Incorrect reassembly 11. or temperatures above104F (40C) may cause an explosion. To ensure product safety, make certain that 12. identical replacement parts. approved by the party responsible for compliance could void the users authority to operate the equipment. 20 mm MADE IN CHINA FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
.Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF Exposure Information The device was evaluated to meet general RF exposure requirements. This equipment should be installed and used with a minimum distance of 0 mm between the radiator and your body. 31.2 mm 2.7 mm