all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
User manual | Users Manual | 1.12 MiB | ||||
1 2 | Cover Letter(s) | |||||||
1 2 | External Photos | |||||||
1 2 | Internal Photos | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | RF Exposure Info | |||||||
1 2 | Test Report | |||||||
1 2 | Test Setup Photos | |||||||
1 2 | Test Report |
1 2 | User manual | Users Manual | 1.12 MiB |
Hughes 9202 User Guide Copyright 2011 Hughes Network Systems, LLC All rights reserved. This publication and its contents are proprietary to Hughes Network Systems, LLC. No part of this publication may be reproduced in any form or by any means without the written permission of Hughes Network Systems, LLC, 11717 Exploration Lane, Germantown, Maryland 20876. Hughes Network Systems, LLC has made every effort to ensure the correctness and completeness of the material in this document. Hughes Network Systems, LLC shall not be liable for errors contained herein. The information in this document is subject to change without notice. Hughes Network Systems, LLC makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hughes and Hughes Network Systems are trademarks of Hughes Network Systems, LLC. All other trademarks are the property of their respective owners. Trademarks Contents Understanding safety alert messages ........................................................................................v Messages concerning personal injury ........................................................................................................ v Messages concerning property damage ..................................................................................................... v Safety symbols ........................................................................................................................... vi Introduction .................................................................................................................................1 Overview .................................................................................................................................................... 1 About this User Guide ............................................................................................................................... 2 Package Contents ....................................................................................................................................... 2 Minimum System Requirements for Laptop/PC ........................................................................................ 3 Getting Started ........................................................................................................................................... 3 Terminal LCD Display .............................................................................................................................. 3 Using the Hughes 9202................................................................................................................5 Terminal Status Page ................................................................................................................................. 5 Connecting the terminal to the computer ................................................................................................... 6 Connecting by Ethernet .......................................................................................................................... 6 Connecting by WLAN ........................................................................................................................... 6 WEP Security ..................................................................................................................................... 7 Connecting by ISDN .............................................................................................................................. 8 Connecting by RJ-11 .............................................................................................................................. 8 Coverage Map ............................................................................................................................................ 9 Using the Hughes UT web UI ...................................................................................................11 Accessing the UT web UI ........................................................................................................................ 11 Home page ............................................................................................................................................... 12 Data .......................................................................................................................................................... 14 Manage Connections ............................................................................................................................ 15 Automatic Context Activation (ACA) ................................................................................................. 16 Manage APNs ...................................................................................................................................... 21 SMS ......................................................................................................................................................... 24 Settings page ............................................................................................................................................ 26 General Setup ....................................................................................................................................... 26 IP Address/DHCP Settings .................................................................................................................. 28 Wireless LAN ...................................................................................................................................... 29 Wireless LAN Security ........................................................................................................................ 30 Telephony ............................................................................................................................................ 32 Security ................................................................................................................................................ 33 Usage Page ............................................................................................................................................... 35 Contents Revision 0.2 iii Support Page ............................................................................................................................................ 36 Troubleshooting ........................................................................................................................39 Technology Overview ...............................................................................................................42 GPS .......................................................................................................................................................... 42 Obtaining a GPS Fix ............................................................................................................................ 42 GPS and BGAN Registration ............................................................................................................... 43 ISDN ........................................................................................................................................................ 43 Dialing and Numbering ........................................................................................................................ 43 PDP Context............................................................................................................................................. 43 Technical Specifications ...........................................................................................................45 Declaration of Conformity .......................................................................................................46 FCC Compliance ...................................................................................................................................... 47 EU RoHS (Restriction of Hazardous Substances) Directive ................................................................... 47 EU WEEE (Waste Electrical and Electronic Equipment) Directives ...................................................... 47 Glossary .....................................................................................................................................49 iv Contents Revision 0.2 Understanding safety alert messages Safety alert messages call attention to potential safety hazards and tell you how to avoid them. These messages are identified by the signal words DANGER, WARNING, CAUTION, or NOTICE, as illustrated below. To avoid possible property damage, personal injury or in some cases possible death, read and comply with all safety alert messages. Messages concerning personal injury The signal words DANGER, WARNING, and CAUTION indicate hazards that could result in personal injury or in some cases death, as explained below. Each of these signal words indicates the severity of the potential hazard. DANGER indicates a potentially hazardous situation which, if not avoided, will result in death or serious injury WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. Messages concerning property damage NOTICE is used for messages concerning possible property damage, product damage or malfunction, data loss, or other unwanted resultsbut not personal injury. Safety Revision 0.2 v Safety symbols calls attention to a The generic safety alert symbol potential personal injury hazard. It appears next to the DANGER, WARNING, and CAUTION signal words as part of the signal word label. Other symbols may appear next to DANGER, WARNING, or CAUTION to indicate a specific type of hazard (for example, fire or electric shock). If other hazard symbols are used in this document they are identified in this section. Additional symbols Warning Potential Radio Frequency (RF) hazard. Where you see this alert symbol and WARNING heading, strictly follow the warning instructions to avoid injury to eyes or other personal injury. Warning Where you see this alert symbol and WARNING heading, strictly follow the warning instructions to avoid personal injury. Danger Electric shock hazard: Where you see this alert symbol and DANGER heading, strictly follow the warning instructions to avoid electric shock injury or death. Warnings for Satellite Terminal Do not stand in front of the Antenna This device emits radio frequency energy. To avoid injury, do not place head or other body parts in front of the satellite antenna when system is operational. Maintain a distance of one meter or more from the front of the Satellite Terminal antenna. General Handle your Satellite Terminal with care. The unit is weather resistant per IEC 60529 IP54; however, do not submerge the unit. Avoid exposing your Satellite Terminal to extreme hot or cold temperatures outside the range -25C to
+55C. Avoid placing the Terminal close to cigarettes, vi Safety Revision 0.2 open flames or any source of heat. Changes or modifications to the Terminal not expressly approved by Hughes Network Systems could void your authority to operate this equipment. Only use a soft damp cloth to clean the Terminal. To avoid impaired Terminal performance, please ensure the units antenna is not damaged or covered with foreign material like paint or labeling. When inserting the SIM, do not bend it or damage the contacts in any way. When connecting the interface cables, do not use excessive force. In the vicinity of blasting work and in explosive environments Never use the Satellite Terminal where blasting work is in progress. Observe all restrictions and follow any regulations or rules. Areas with a potentially explosive environment are often, but not always, clearly marked. Do not use the Terminal while at a petrol filling station. Do not use near fuel or chemicals. Qualified Service Do not attempt to disassemble your Satellite Terminal. The unit does not contain consumer-serviceable components. Only qualified service personnel may install or repair equipment. Accessories Use Hughes approved accessories only. Use of non-approved accessories may result in loss of performance, damage to the Satellite Terminal, fire, electric shock or injury. Battery Use only battery approved by Hughes. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Connecting Devices Never connect incompatible devices to the Satellite Terminal. When connecting the Satellite Terminal to any other device, read the devices User Manual for detailed safety instructions. Safety Revision 0.2 vii Pacemakers The various brands and models of cardiac pacemakers available exhibit a wide range of immunity levels to radio signals. Therefore, people who wear a cardiac pacemaker and who want to use a Satellite Terminal should seek the advice of their cardiologist. If, as a pacemaker user, you are still concerned about interaction with the Satellite Terminal, we suggest you follow these guidelines:
Maintain a distance of one meter from the main antenna front and sides and your pacemaker;
Refer to your pacemaker product literature for information on your particular device. If you have any reason to suspect that interference is taking place, turn off your Satellite Terminal immediately. Hearing Aids Most new models of hearing aids are immune to radio frequency interference from Satellite Terminals that are more than 2 meters away. Many types of older hearing aids may be susceptible to interference, making it very difficult to use them near a Terminal. Should interference be experienced, maintain additional separation between you and the Satellite Terminal. Electrical Storms Operation of the Satellite Terminal during electrical storms may result in severe personal injury or death. Ensure the Below Deck Equipment is properly grounded to the vehicle chassis. viii Safety Revision 0.2 Overview The Hughes 9202 Land Portable Terminal is the latest Hughes BGAN product that provides reliable satellite connectivity over the Inmarsat BGAN satellite network in a very small and portable package. It allows the user to send and receive IP packets via Ethernet and WLAN interfaces. In parallel with the packet data services, the Hughes 9202 supports circuit switched voice and fax calls via standard POTS and ISDN interfaces. The Hughes 9202 offers you the following features and benefits:
Small, compact IP terminal with the following interfaces:
o Wi-Fi access point built-in o 1X RJ-45 Ethernet port o 1X RJ-45 ISDN port for voice, 3.1KHz audio and UDI/RDI data (64Kbps) o POTS RJ-14 port for voice and fax Multi-user capability for sharing a single unit Selectable Quality-of-Service (QoS) up to 128Kbps streaming Full IP compatibility for Email, file transfer (FTP), browsing, VPN, etc. Cost-effective always-on access charges only for data sent and received UMTS IP-based services FCC and CE certified Subscriber Identification Module (SIM) card security In this document, the following names and abbreviations are used to identify the Satellite Terminal and your computer. Term Definition Terminal Satellite Terminal TE UT Terminal Equipment (your computer) User Terminal/satellite terminal Introduction Revision 0.2 1 About this User Guide Package Contents This user guide contains the most up-to-date information available on this product, on the date it was generated. It is focused on the specific information needed to operate the Hughes 9202 Land Portable Terminal. Please refer to the Hughes 9201 User Guide for general information on how to access the BGAN network and how to use the Inmarsat LaunchPad Software. The 9201 User Guide can be downloaded from the Hughes website at www.bgan.hughes.com. When you unpack the Hughes 9202 Land Portable Terminal Kit package, you will find the following:
Hughes 9202 terminal assembly AC/DC power adapter Ethernet cable Lithium Ion battery Your Service Provider will supply you with a Subscriber Identification Module (SIM) and its PIN, and Satellite Terminal configuration instructions you will need these to access the network. Note: The SIM card may also have four (4) MSISDN numbers associated with it for various ISDN services:
4K Voice 3.1KHz Audio/Fax 64K UDI data 56K RDI data 2 Introduction Revision 0.2 Minimum System Requirements for Laptop/PC Getting Started These are the minimum computer system requirements for successful interface with the Satellite Terminal:
Internet Browser: Microsoft Internet Explorer, Mozilla or Safari. PC Support for at least one of these interfaces: Ethernet, WLAN (802.11b or b/g), or ISDN. 100 MB of free hard disk space if using LaunchPad. This guide is the simplest and quickest way to connect to the BGAN network. If you are a first time user, you will be guided through the procedure for powering up your terminal, obtaining a GPS fix, connecting your computer to the terminal and registering with the BGAN network. You are then ready to start using voice and broadband services. Terminal LCD Display The 9202 terminal has an LCD display and provides four buttons for the user. Each button has two primary functions, one invoked with a short press and the other invoked with a long press. The top icon associated with a button is the long press function. The bottom icon associated with a button is the short press icon. These are tabulated as follows:
Introduction Revision 0.2 3 Button Name Short Press Long Press Scroll Scrolls through a menu Turns WiFi on/off Back Up one level in menu Cancel menu Accept Enters menu and confirms selection Power on/off User Selects the user to display Audio on/off Note that a short press shall be defined as any debounced keystroke less than two seconds in duration. A long press shall be defined as any debounced keystroke that is two seconds in duration or greater. A long press shall not end until the button is released (i.e., an extended long press shall not be interpreted as multiple keystrokes). An extra long press shall be defined as a long press that continues for more than five seconds. Long press actions are selected to avoid accidental invocation (power on/off, connect/disconnect). Extra long press actions are selection to ensure intentional action by the user (hardware enforced power down). 4 Introduction Revision 0.2 Short Press UT State Result Scroll button On, menu item Scroll to next option of displayed menu item Back button On, menu item Goes up one level in menu Accept button On, pointing Exit pointing, start normal operation On, status display Enter menu On, menu item Confirm selected menu item User button On Select the next user terminal equipment connected to the UT (.101, .102, ) Long Press UT State Result Scroll button On, status display Toggle WiFi on/off (save state in NVRAM) Back button On, menu item Cancel menu action, return to status display Accept button Off Turn on, LCD lamp test confirms button action On Turn off, UT ignores additional power button input until power down sequence is complete User button On Toggle audio pointing tone on/off Special Action UT State Result Accept and User buttons, simultaneous long press Off Go to minimum boot mode Accept button, extra long press On Hardware enforced power down Terminal Status Page Since the Hughes 9202 terminal is a portable device, you must first obtain a GPS fix and point the terminal to the satellite before setting up a data connection with the network. The Terminal Status page gives you all the information you need to point and register with the network. Once you have a GPS fix and are pointed to the satellite as best you can, click on the Register with the Network button to start the registration process. Once you are registered and CS and PS Attached, you can then select the Quality of Service (QoS) for your data connection by choosing either the Standard or Streaming connection Using the Hughes 9 Revision 0.2 5 Connecting the terminal to the computer You can connect your computer to the 9202 with one or more of the following interfaces Ethernet WLAN Integrated Services Digital Network (ISDN) There is no need to check the active interface. All interfaces can be used simultaneously to accommodate multiple users. During initial setup, the terminal can only be configured using an Ethernet connection. Once the terminal has been configured, all interfaces (Ethernet, WLAN and ISDN) can be used for data transfer depending on the service required. Your computer must be configured to support your chosen connection method. Refer to the documentation supplied with your computer for details. To connect the BGAN terminal to a device using Ethernet:
Connect an Ethernet cable to your devices Ethernet port, and insert the other end of the connector into the Ethernet port on the 9202.. If you have not previously used the 9202s WLAN interface, it has to be enabled from the internal web UI, Integrated MMI or LaunchPad with your computer connected to the 9202 using the Ethernet interface. Connecting by Ethernet Connecting by WLAN 6 Using the Hughes 9 Revision 0.2 WEP Security WLAN Power: The default is off, which disables the WLAN feature. SSID (network name): The default is BGAN, but you can change it to whatever you want. Channel Number: This controls the radio channel number (1 through 11) used by the access point. To meet FCC regulations, channels 12 to 14 are not supported. As you are configuring the WLAN, you can enable the Wireless Encryption Protocol (WEP), MAC address filtering and no broadcast SSID features for added security. Once the WLAN is Enabled and configured, any device with a WLAN interface can detect the 9202s WLAN SSID, and connect to it automatically. WEP Protection Status: Check the box to Enable the WEP for added security. Encryption Level: 64 or 128 bit WEP encryption can be enabled. WEP Key: You can define the WEP key or use the default WEP key, which is formulated using the IMEI number of the terminal (e.g. IMEI number +0123456789). Hexadecimal 128-bit: Requires 26 characters. Recommended Hexadecimal 64-bit: Requires 10 characters SSID Broadcast: For added security you can choose not to broadcast your SSID. MAC Filtering: For added security, check the box to Enable MAC Filtering. You can define up to 10 MAC addresses that are allowed to connect to your WLAN. To determine the MAC address of a PC, go to a DoS prompt and type ipconfig/all. For Mac OS X, under the Apple Menu go to System Preferences -> Network and Show Airport. The Airport Id is the MAC address. Alternatively, go to About this Mac -> More Info -> network, and select Airport. Using the Hughes 9 Revision 0.2 7 Connecting by ISDN Connecting by RJ-11 When WLAN is enabled, unauthorized users may be able to access your BGAN service. If WEP is enabled, you must provide other WLAN users with the WEP key in order for them to connect to the terminal. You can go to the Manage Connections page to see what computers are actually using the BGAN service. Connect an ISDN cable to your computers or phones ISDN port, and insert the other end of the connector into the Terminals ISDN port. To dial, prefix the international number with 00 and terminate with #. For example, to dial a number in the USA, enter:
0018005551234# (00 + Country code + phone number #). For the UK dial 00011442077281000#. To receive incoming calls you must configure your ISDN device with the MSN (Multiple Subscriber Number) of the service it supports. See the ISDN section for information on configuration of MSNs. To configure the MSN in your ISDN device, refer to the user guide of your ISDN device. You can connect an analog phone or fax machine to the RJ-11 ports:
The FAX port is configured for 3.1k service for fax The TEL port is configured for speech service for voice calls To dial, prefix the international number with 00 and terminate with #. For example, to dial a number in the USA, enter:
0018005551234# (00 + Country code + phone number #) Operational note: RJ-11 and ISDN handsets cannot be connected at the same time. The 9202 will configure itself to ISDN or RJ-11 mode depending on which type of handset is plugged in first, and will be in this mode thereafter. To switch modes, the 9202 must be rebooted with only the desired handset connected. If both types of handsets are connected at power-on, the 9202 will default to ISDN mode and RJ-11 will not be operational. 8 Using the Hughes 9 Revision 0.2 Coverage Map The Inmarsat BGAN service is operated with 3 satellites as shown below. The Hughes 9202 terminal will perform best in areas where the elevation angle is 20 degrees or higher but can operate down to 5 degrees. Using the Hughes 9 Revision 0.2 9 Accessing the UT web UI The Hughes UT includes its own internal Web User Interface
(UI). To access the web UI, open your favorite Web Browser and type in the internal IP address of the UT e.g. http://192.168.128.100. The web UI opens up to the Home or Terminal Status page as shown below:
Using the Hughes 9 Revision 0.2 11 Home page The Home page shows the current terminal status and allows you to setup your initial data connection. On the left side of the page is the Status bar. These items are updated automatically when the status of any of these items change. 1. Connection: This field indicates whether you are Registered with the Network. It also shows the PS and CS status, beam type and receive signal quality. a. PS Attach Status: This field indicates whether you are PS (Packet Switch) attached with the Network. You will still need to setup a PDP context in order to send PS data. b. CS Attach Status: This indicates whether you are CS
(Circuit Switch) attached with the Network. Once you are CS Attached and Registered with the network, you are able to make CS calls. 2. GPS: This field displays the current GPS position status. If you have received a GPS fix and the Network GPS policy has been received and it allows the GPS position to be shown to the user, it will display the Latitude, Longitude, Fix Quality, and the Last time the GPS position was updated. Time displayed is UTC time. 3. BGAN terminal: This field indicates the WLAN status. 4. Antenna Unit: This field indicates the detailed state of the tracking antenna a. The state field indicates the tracking state of the antenna b. Elevation: the current elevation look angle of the antenna c. The frequency of the global beam in MHz that the antenna is attempting to track is displayed. If the unit is experiencing problems, use the table below to verify the antenna is searching for the correct satellite for your location The frequency is the frequency of the global beam. Possible values are the primary and secondary frequencies of the three satellites. 12 Using the Hughes 9 Revision 0.2 Satellite ID Satellite Primary I4-F1 Asia Pacific I4-F2 Europe, Middle East &
Africa Satellite Longitude Primary Freq MHZ Alternate MHz 143.5 E 1537.485 1540.825 25.0 E 1537.920 1541.115 I4- Americas 98.0 W 1537.070 1540.730 In the middle of the page you will find the following items:
Current Connection field allows you to activate data connections for your TE. You can activate a Standard connection or a Streaming connection. For streaming connections use the drop down box to select the data rate for the stream. Connect using APN field allows you to control the APN used for the connection. Detail shows the status of the connection for this TE. Visible Satellites shows the satellites visible for your current location and the pointing information. Reference the screenshot below. The antenna angle under Visible Satellites section (46.5) may not be exactly the same as seen under the Antenna Unit section showing Elevation (35). This is due to the wide beam width of the antenna The following figure shows how the UI looks if you activate a Standard connection. Use the Disconnect button to deactivate your connection. Using the Hughes 9 Revision 0.2 13 Data The Data icon has three main configuration areas to select from:
Manage Contexts, Automatic Context Activation (ACA), and Manage APN. The following section will review each of these pages. 14 Using the Hughes 9 Revision 0.2 Manage Connections Manage Connections page under the Data tab allows the user to setup and configure PDP contexts (data connection) for any TE that is connected to the UT. It also shows you all current Active Connections. Open a New Connection - To open a new connection, enter the required data in the lower box. Owner Your current IP address is shown by default (.101), but you can change it to control connections for any other device connected to the terminal. The page automatically displays entries for all detected devices and these entries can be selected to activate connections for those devices. Service - Select the service that you want by clicking on the down arrow. The drop down list shows all of the different QoS types: standard, streaming 32K, streaming 64K, and streaming 128K. Select the appropriate service required. APN - The APN is read from the SIM card, but if you have other APNs defined (go to Manage APN page), you can use the down arrow to select a different APN. Once everything is defined Using the Hughes 9 Revision 0.2 15 correctly, click on the Open Selected Connection button. The new context will appear in the All Active Connections field above. Close a Connection - In the upper field, all active connections are shown and you can select and close any of these connections unless an Administration Password has been enabled. See Security Section for more information about the administration password. Username (UN)/Password (PW): Some Service Providers require a username and password to be used when setting up a connection. This is often required when using Static Global IP addresses assigned by the Service provider. These fields can be entered when defining a new APN or when you select a different APN. Automatic Context Activation (ACA) This web page allows you to use Automatic Context Activation
(ACA) in two different ways;
One way is to use a static IP addresses in the TE device so you can establish an automatic PDP context with any QoS that is offered by the network (upper half of the web page). The second way is to use DHCP IP addresses from the UT so you can establish an automatic standard PDP context for any TE that connects via DHCP to the UT (lower part of the web page). You can also choose whether the context should be activated as soon as the UT detects the device, or if the context should only be activated when the TE attempts to send data to the satellite link. For the data activated option, choose DA from the drop down list rather than just On in either static or DHCP sections. 16 Using the Hughes 9 Revision 0.2 With DA, if the context is ever deactivated, it will be reactivated when more data is sent. Static IP Automatic Contexts: You can configure your own range of static IP addresses and QoSs to use with a static automatic context. To turn on a particular range of static addresses, select On from the drop down list and choose a range of addresses, low and high to use (e.g. 192.168.128.200 to 192.168.128.202) or you can leave the defaults (192.168.128.200 to 192.168.128.209). Next select the desired QoS for that range of IP addresses (e.g. Standard). The APN listed is the default APN read from the SIM card (bgan.inmarsat.com). If your SIM is provisioned for more than one APN, then you can select a secondary APN from the drop down list. Using the Hughes 9 Revision 0.2 17 If you want to setup additional ranges of addresses, please follow the same instructions as above. You cannot overlap the IP address ranges. If you do, an error will pop-up telling you that you have an overlap region. Check all of the ranges for overlaps and try again. When you are finished, click on Apply and you should see a message saying Operation Successful. DHCP Automatic Contexts: This option allows you to set up the UT for dynamic standard ACA. This means that any device connected to the UT via DHCP, whether wired or wirelessly will automatically receive a standard context. 18 Using the Hughes 9 Revision 0.2 To activate this feature, select On from the drop down list under DHCP Automatic Context section, select the DHCP range of addresses to use if you dont want to use the default (.101 -
.199), select the APN that you want to use and click on Apply. To see if the context has been setup properly, click on the Data tab>Manage Connections Page and this will show you all contexts that have been setup (active or inactive). See screen shot below. Using the Hughes 9 Revision 0.2 19 20 Using the Hughes 9 Revision 0.2 Manage APNs Some SIM cards are provisioned with multiple APNs, so you can use this page to pre-configure those additional APNs if needed. Once the APN is defined, you can select it from the drop down list without having to put in the username and password every time. Using the Hughes 9 Revision 0.2 21 Add an APN Use this field to add an APN that you want to use. Type in the new APN and username and password (if required). If you want to save the username and password so you dont have to re-type it each time, check the Save username and password box and then click on Add. The new APN name will show up in the Defined APNs field. This APN will now be available to use from any APN drop down menu. Username (UN)/Password (PW): Some Service Providers require a username and password to be used when setting up a connection. This is often required when using Static Global IP addresses assigned by the Service provider. You can also edit a defined APN if needed. Click on the APN in the Defined APNs section and click on EDIT. Make the required changes and click Add. 22 Using the Hughes 9 Revision 0.2 Screenshot shows the new APN that was added, in the Defined APNs section. Using the Hughes 9 Revision 0.2 23 SMS You can manage SMS text messages from the SMS pages which provide a similar function to LaunchPad. You must have a valid Service Center number configured in order to send messages see the SMS Settings Page. Send/Receive this page allows you to view your Inbox box messages and Compose a new message. If there are more than 10 messages, you can view the older ones by changing the page number. You can also reply to received messages or forward them to another number. You may need to periodically delete messages to prevent the SIM from filling up which will prevent the receipt of new messages. You can select a single message by checking the box next to the message and press the Delete Checked button. To delete multiple messages just select the check box next to each message you want to delete and click the Delete Checked button. After composing a message you can save it to drafts rather than sending it, by pressing the Save button. The Sent Messages section allows you to view previously sent messages. Again, you may need to periodically delete messages to prevent the SIM from filling up. You can also compose a new message from this page. 24 Using the Hughes 9 Revision 0.2 The Saved Drafts page allows you to view previously saved messages. After editing a message you can resave (Save) or send the message (Send). You can also compose a message from this page. On the SMS Settings page you can configure the default settings for messages. You must have a valid Service Center number configured in order to send messages. The default Service Center number is +87077200179. Using the Hughes 9 Revision 0.2 25 Settings page General Setup 26 Using the Hughes 9 Revision 0.2 This page allows the user to configure various parameters of the UT. A description of each item on this page follows:
Terminal Startup The default configuration for the 9202 terminal has Bypass Antenna pointing and Always power on checked and grayed out due to the tracking antenna. Connection The default configuration is always set to Automatic. This parameter is used within a satellite overlap region and allows the user to override the default satellite
(selected by the 9202 terminal based upon elevation angle/GPS location) and select a different satellite. This change does not take effect until the UT is reset. When set to Automatic, the UT will select the satellite based on the units GPS position. When set to a specific satellite, it will attempt to use that satellite only. Be careful to select the correct satellite for your position. Streaming By enabling this parameter, the user can turn on a timer for inactivity for a streaming QoS that has been set up. The timer is in either seconds or minutes and will tear down a streaming context after X seconds or minutes of inactivity. Emergency Call Numbers: Allows the user to add the emergency call number that is applicable in the part of the world where the terminal is being used, if it is not already defined. Apply Changes Button: This button is self-explanatory. Using the Hughes 9 Revision 0.2 27 IP Address/DHCP Settings Terminal Local IP Address: This page allows the user to change the local IP address of the terminal from the default 192.168.128.100 IP address. All four octets are available to change. Once the local IP address is changed on this page and applied, the IP address ranges for the DHCP server, the Manage Context page and ACA page will also be changed automatically. Updates to this field will not take effect until the UT is rebooted. DHCP Server: allows the DHCP server in the UT to be turned on or off by checking the Enable box. DHCP Address Range: This allows the user to set the range of DHCP addresses that are given out by the UT to any connected TE. Lease Time when idle: Idle-mode DHCP Lease Time refers to the DHCP lease time when the UT is not connected to the network. This parameter allows the user to change the default time (60 seconds) that the DHCP lease to the TE is good for. This parameter was introduced because of a problem with some models of Cisco routers that will not accept a short DHCP lease time. 28 Using the Hughes 9 Revision 0.2 Wireless LAN The longer the Idle-mode DHCP lease time, the longer it will take the Network/UT to update the TE with the correct DNS servers for web browsing after establishing a data context. Lease Time when connected: The Connected-mode DHCP Lease Time refers to the DHCP lease time when the UT is connected to the network. Most users will have no need to change this parameter. The Wireless LAN settings page allows the user to enable, disable, and configure the Wireless LAN functionality of the terminal. The Wireless LAN Security is controlled on a separate web page WLAN Security. 29 Using the Hughes 9 Revision 0.2 Wireless LAN Security If you have not previously used the terminals WLAN interface, it has to first be enabled from this page using a computer connected to the terminal using an Ethernet connection. Once WLAN is enabled/configured, TEs can connect to the terminal wirelessly. Fields on this page include:
Enable Wireless LAN Interface: Turns the Wireless LAN interface on/off. The default is off (unchecked). Network Name (SSID): The default is BGAN, but you can change it to whatever you want. You can hide/prevent the SSID broadcast on the WLAN Security page Network Region: There is only one region for all countries. Network Channel: This controls the radio channel number (1 through 11) used by the access point. To meet FCC regulations, channels 12 to 14 are not supported. If performance issues occur over the WLAN interface, changing the Channel may help. This page allows the user to configure WEP Security for use when the terminal is communicating wirelessly to TEs. Additional security measures that can be used with WEP to make it more secure are: 1) Do not broadcast your SSID and 2) enable MAC address filtering so that only the MAC addresses that you select, can connect to the terminal. A maximum of ten
(10) addresses can be filtered. Check the box if you want your SSID name to be broadcast. Select from the down arrow, No protection, 64 bit WEP and 128 bit WEP. Mac Address Filtering Check the box to Enable MAC Address Filtering If any TE is already connected to the terminal wirelessly, the MAC address of that TE will be detected and show up in the Add a Detected Device field. 30 Using the Hughes 9 Revision 0.2 To add the detected MAC address, click on the address to highlight it and then click Add. It will now show up in the Allowed MAC Address field. Using the Hughes 9 Revision 0.2 31 Telephony You can establish ISDN data communication by connecting your ISDN equipment directly to the BGAN Terminals ISDN port with an ISDN cable (which is the same as the Ethernet cable). The Telephony page allows you to activate 40V power sourcing on the ISDN interface, and configure Device MSN Settings. General ISDN Settings:
Enable ISDN Power Sourcing: To turn on the ISDN power sourcing, click the check box in the upper left-hand corner that says Enable ISDN Power Sourcing and then click on Apply. The ISDN device should receive 40V power immediately via the ISDN cable. This field should be on unless you never use ISDN or are using an ISDN device that has its own power source. Select the outgoing call type using: This box controls the mechanism used by the terminal to select the bearer type for mobile originated calls. By default, the Device Bearer capability is set as the trigger in this drop down list. Most ISDN devices correctly signal the call type (speech, 3.1 KHz audio, UDI, RDI) via the bearer capability. 32 Using the Hughes 9 Revision 0.2 There is also an option under the drop down arrow to set the trigger to use the MSN rather than the bearer. If there is a problem using the bearer capability setting, this field can be changed to use the MSN number instead. Device MSN Settings - Voice/FAX Devices Standard Voice: By default, MSN 1 is used for standard voice
(speech). To receive incoming calls, you must program the same MSN into your ISDN handset connected to the ISDN port. Premium Voice/Fax (3.1 kHz Audio): By default, MSN 2 is used for 3.1 KHz Audio. To receive incoming calls, you must program the same MSN into your ISDN fax machine connected to the ISDN port. Device MSN Setting - 64 kbps Data Devices 64 kbps Clear Data UDI (Unrestricted Digital Information): By default, MSN 3 is used for UDI calls. UDI is a 64 Kbps service that is a European standard ISDN. 64 kbps Restricted Data RDI (Restricted Digital Information): By default, MSN 3 is used for RDI calls. RDI is a 56 Kbps service found in the USA. Once all changes have been made, click on Apply. You can use different MSNs for any of the ISDN call types above, but your ISDN equipment must be programmed with the same MSN to accept incoming calls, and you must use different numbers for speech, audio and UDI/RDI calls. You can configure three separate security settings on this page:
1) SIM PIN, 2) Phone to SIM PIN, and 3) Administration Password. SIM PIN this is a four digit field can be Enabled and configured by the user to secure the terminal against unwanted use. Once enabled, the terminal will require the SIM PIN at startup. Phone to SIM PIN use up to 5 digits to lock the terminal to that particular SIM. The Phone to SIM PIN will have to be Using the Hughes 9 Revision 0.2 33 Security entered any time the SIM card is changed. This setting is similar to your GSM phones security code. Default password is 12345. Administration Password this configuration allows the user to prevent terminal settings from being changed once the terminal is configured properly. This password will have to be entered before any settings can be changed. 34 Using the Hughes 9 Revision 0.2 Usage Page This web page provides an estimate of the amount of Packet Switched data that was sent and received, along with time spent on streaming connections and CS calls. The data is broken up into two types:
Trip Usage Statistics: The trip counter is similar to the trip counter on your vehicle. It can be zeroed out at anytime by the user and it will track the statistics until the user resets it. Lifetime Usage Statistics: The Lifetime counter is similar to the odometer on your vehicle. It shows the statistics of the terminal since the software version that added this feature was loaded onto the UT. The user cannot reset these counters. If the UT power is abruptly disconnected for some reason, the UT will not be able to save the statistics to flash and hence the statistics for the session (Trip) may be inaccurate. Using the Hughes 9 Revision 0.2 35 Support Page This web page allows you to display technical and support information about the terminal and retrieve logs. 36 Using the Hughes 9 Revision 0.2 Information and Support Terminal Information Model: this displays the UT model number. Class: this indicates the UT Class, such as Class 11 for a land mobile terminal or Class 10 for high gain land mobile terminal. IMEI: This displays the IMEI (serial) number of the UT. Software Version: This displays the current version of software that is running on the UT. SIM Information IMSI: This displays the IMSI number of the SIM card in the UT. If is the IMSI is not displayed, it indicates that there is a problem reading the SIM card, e.g. because there is no SIM, it is installed incorrectly or PIN must be entered. Default APN: This is read directly from the SIM card. Terminal Support contact information retrieved from the SIM card. Website Telephone E-Mail Troubleshooting Terminal Log Files: This allows you to extract and save any of the following log files for troubleshooting purposes:
System Log Event Log Packet Log Circuit Log These files can be e-mailed to Hughes directly for fault analysis if the user experiences any problems. Reset Terminal to Factory Defaults: Clicking the Restore To Defaults button will restore the UT back to the factory default settings and delete any of the user parameters that have been set-up in the UT. Using the Hughes 9 Revision 0.2 37 Hughes highly recommends that the user exhaust all possible troubleshooting procedures before using this feature Reboot terminal: Clicking this button reboots the terminal so that configuration changes can be saved into the configuration file or can be used when just a simple reboot of the terminal is required. 38 Using the Hughes 9 Revision 0.2 Problem Possible Cause Possible Solution Terminal will not turn on Power switch not on No ignition sense Fuse is blown Cannot get SIM card to lock into position SIM is not correctly oriented for insertion The BGAN LaunchPad or web UI will not connect to the terminal No interface connection between the terminal and computer Your computer is configured with a static IP address in the wrong subnet. Default UT IP address is: 192.168.128.100 Check the power switch is in the ON position and LED is on Check positive voltage is applied to the ignition sense pin of the power connector Remove fuse and check. Refer to Installation Manual Ensure the SIM is pressed firmly into the SIM slot Ensure the SIM is oriented as shown in on the terminal and in the Install Guide Ensure there is a WLAN or Ethernet connection between the terminal and computer, see User Guide Check the IP configuration settings on your computer. Enable DHCP or use a static IP address in the same subnet as the UT local IP address. Default UT IP address is:
192.168.128.100 Troubleshooting Revision 0.2 39 Problem Possible Cause Possible Solution Terminal will not accept incoming ISDN calls The MSN programmed into the ISDN device does not match the MSN programmed into the terminal Terminal will not make outgoing ISDN calls ISDN power sourcing is turned off Terminal is not Registered with the Network. Terminal is connected to the BGAN network, but cannot obtain the requested Quality of Service Network temporarily not available User tried to set up a 256 Kbps streaming connection. Terminal does not obtain a GPS fix Terminals location limits visibility of 3 or more GPS satellites. Ensure the appropriate MSN is programmed into the ISDN device, see User Guide Ensure the appropriate MSN is programmed into the terminal, see ISDN Section of User Guide Enable the ISDN power sourcing from the BGAN LaunchPad or ISDN web UI page (unless the ISDN device has a separate power source). Check the Properties page in web UI to make sure the unit is CS attached. Retry again. If problem persists, contact your service provider. The Inmarsat Network only supports 256K for Class 1 terminals and only 128K connections for Class 2 UTs Move the terminal to a location where there are few obstructions such as trees or tall buildings, so that as much as possible of the sky is visible. 40 Troubleshooting Revision 0.2 Problem Possible Cause Possible Solution ISDN device does not operate correctly The ISDN device is trying to draw too much power from the satellite terminals ISDN interface The device you are connecting is not an ISDN device. It might be an Ethernet device that you are accidentally connecting to the ISDN port. Make sure that you dont have both RJ-11 and ISDN handsets connected at the same time. None of the above solutions resolve the problem Terminal may have a hardware or software fault, and needs to be re-booted. Only connect an ISDN device that draws less than 70mA of current at 40V (equivalent power 2.8W) Make sure you connect only ISDN devices to the ISDN port Remove one of the handsets and reboot the terminal. Remove power. Wait 30 seconds. Reconnect the DC power and turn on the terminal. Troubleshooting Revision 0.2 41 GPS Obtaining a GPS Fix The Global Positioning System (GPS) uses 24 orbital satellites to determine the position of the Terminal anywhere on the globe. In normal operation, a GPS receiver, such as that built in to the Tracking Antenna, needs to be able to receive signals from at least four satellites so that it can then calculate a latitude, a longitude and an altitude this position fix is referred to as a 3-
dimensional or 3-D fix. If only three GPS satellites can be seen by the GPS receiver, then the last available altitude measurement is assumed and the GPS receiver calculates a position fix based on latitude and longitude only. This simpler position fix is referred to as a 2-dimensional or 2-D fix and is quicker and easier to obtain than a 3-D fix, but may be less accurate. The GPS receiver may take between a few seconds and a few minutes to obtain a GPS fix, depending on how frequently the GPS receiver is being used. The frequency of use determines the how quickly the GPS Terminal is able to start. Hot start if the GPS receiver is being used frequently, (that is, in the last two hours), it is regularly updated with data from the GPS satellites, and so only takes a few seconds to obtain a GPS fix after being switched on. Warm start if a GPS receiver has not been used for more than two hours, then it will take up to 45 seconds to obtain a GPS fix. Cold start if the GPS receiver has not been used for some time or is 300 km or more from where it was last used, it can take as long as 15 minutes to obtain a valid position fix. The time taken to obtain a valid GPS fix can also be affected by the visibility that the GPS receiver has of the GPS satellites. The GPS system is relatively tolerant of atmospheric conditions such as heavy cloud or rainfall. However, physical blockages, such as tall buildings or terrain can significantly degrade the ability of the GPS receiver to obtain a fix. For this reason, ensure that the GPS receiver has a clear view of as much open sky as possible. 42 Technology Overview Revision 0.2 GPS and BGAN Registration ISDN Dialing and Numbering PDP Context BGAN uses the accurate position and timing information obtained from GPS to help ensure efficient registration of a BGAN Terminal with the BGAN network. The Satellite Terminal provides an ISDN (Integrated Services Digital Network) interface to connect devices for Circuit Switched voice and data services. It is a Basic Rate (also known as 2B+D) interface and uses the Euro ISDN protocol. Note that the Satellite Terminal can only provide service for one 64Kbps B-channel at a time. Dialing - As the ISDN numbering system follows the same pattern as the normal telephone system, dialing is carried out in exactly the same manner as making a normal telephone call. The subscriber number is used with the same international and area codes as any other telephone network. Start the dialed number with 00 and terminate it with a #. Multi-Subscriber Numbering (MSN) - ISDN supports Multi-
Subscriber Numbering (MSN). MSN is a facility whereby more than one telephone number can be allocated to an ISDN line. The BGAN Satellite Terminal assigns different MSNs for Voice, 3.1KHz Audio, UDI and RDI devices. Each incoming call will be directed to the appropriate MSN depending on the type of call. This allows proper routing of incoming calls to the correct ISDN device (e.g. ISDN phone, data card or Fax). A Packet Data Protocol (PDP) Context defines connection aspects such as routing, Quality of Service (QoS), security and billing between a mobile user terminal, such as the BGAN Terminal, and a data network. PDP Contexts are essential to the General Packet Radio Service (GPRS) system, which is used by GSM and UMTS-based 3G networks worldwide for transmitting data. In order for a user to be able to transfer data across a network, a PDP Context must be activated in the Terminal and associated Core Network. The procedure for this is as follows:
Technology Overview Revision 0.2 43 1. After registration with the network, the user activates a PDP Context using an application on the computer or Terminal, and requests sufficient radio resources (that is, power and bandwidth) to support the context activation procedure. 2. Once the resources are allocated, the Terminal sends the Activate PDP Context request to the Core Network. This request includes key information about the mobile user's PDP address (for example an IP address), PDP type (that is, static or dynamic address) the QoS requested for this context, the APN of the external network to which connectivity is requested, the user's identity (IMSI) and any necessary IP configuration parameters (for example, security settings). 3. On receiving the Activate PDP Context message, the Core Network checks the user's subscription record to establish whether the request is valid. If the request is valid, a virtual connection is established between the Terminal and the Core Network, and data transfer can then take place between the Terminal and the external data network, within the scope of the current PDP Context. The PDP Context is stored in both the Terminal and the Core Network. A single Terminal may have multiple PDP Contexts each with different QoS profiles. The primary PDP Context is a PDP Context with default QoS profile attributes and is always activated first. All other PDP Contexts with the same PDP Address are secondary PDP Contexts. Secondary PDP Contexts share the same PDP Address and connect to the same APN but may have different QoS profiles. 44 Technology Overview Revision 0.2 Satellite TX Frequency Satellite RX Frequency GPS Frequency SAT Continuous TX Time (@128kpbs) SAT Continuous RX Time (@128kbps) SAT Standby Time Weight Dimensions Operating Temperature (with battery) Operating Temperature (with DC supply) Battery Charging Temperature Storage Temperature (including battery) Storage Temperature (excluding battery) Humidity Wind Water and Dust Non-operational Mechanical Vibration Input Voltage Battery Data Connectivity Other Features Note:
1626.5 1660.5 MHz and 1668 1675 MHz 1518 1559 MHz 1574.42 1576.42 MHz Up to 2.5 hoursnote1 Up to 4 hoursnote1 Up to 36 hoursnote1
< 1.8Kg 216 mm x 216 mm x 45 mm
-5C to +55C
-25C to +60C 0C to +40C
-20C to +80C
-25C to +80C 95% RH at +40C Operational wind loading (with stand secured to ground) 40kph (25mph) IP 54 Compliant 200-2000Hz, 0.3 m2/s3 MIL-SPEC 810B Method 500.3, Procedure 1 19V 7.2V 2.5Ah Li-Ion, rechargeable RJ45 port (Ethernet 10BaseT) RJ11 port (POTS) RJ45 port (ISDN) 802.11b WLAN Integrated User Interface (iUI) via LCD panel Web User Interface (WebUI) SIM/USIM Slot (behind battery) AC/DC adapter Rechargeable Li-Ion battery inch UNC threaded hole for tripod mounting Compass to assist pointing 3.4Anote2 1. Performance may be affected by a wide range of factors. 2. The Hughes 9202 broadband satellite terminal operates on DC power which can be supplied by an AC or DC power source. To comply with safety requirements, the terminal must be powered with only an AC/DC adapter or DC power adapter supplied or approved by Hughes. Technical Specifications Revision 0.2 45 We,
(manufacturers name) Hughes Network Systems of
(address) 9605 Scranton Road, Suite 500, San Diego, CA 92121, USA declare under our sole responsibility that the product
(detailed description of product including name, type, model and supplementary information such as lot, batch or serial number, sources and number of items) Hughes 9202 BGAN Land Portable Terminal to which this declaration relates, is in conformity with the following standards and/or other normative documents:
For article 3.1(a), Health and Safety of the User:
EN 62311 IEC 60950-1 (2nd Edition) For article 3.1(b), Electromagnetic Compatibility:
EN 301 489-1, EN 301 489-17, EN 301 489-20 For article 3.2, Effective Use of the Spectrum Allocated:
EN 301 444 EN 300 328 We hereby declare that all essential radio test suites have been carried out and that the above named product is in conformity to all the essential requirements of Directive 1999/5/EC. Identification mark:
The equipment will also carry the Class 2 equipment identifier:
The technical documentation relevant to the above equipment will be held at:
Hughes Network Systems, 9605 Scranton Road, Suite 500, San Diego, CA 92121, USA
(name and address of EU representative) Bill Lindsay
(name) Senior Engineering Program Director
(title)
(signature of authorized person)
(date) 46 Declaration of Conformity Revision 0.2 FCC Compliance EU RoHS (Restriction of Hazardous Substances) Directive EU WEEE (Waste Electrical and Electronic Equipment) Directives This device conforms to the FCC rules. Any changes or modifications to Hughes Network Systems equipment, not expressly approved by Hughes Network Systems, could void the user's authority to operate the equipment. To comply with FCC RF exposure requirements, this device must be operated with a minimum separation distance of one meter or more from a person's body. Other operating configurations should be avoided. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The European Union (EU) Directive 2002/95/EC restricts the use of certain hazardous substances in electrical and electronic equipment. Unless otherwise noted, all products, assemblies, and sub-
assemblies manufactured by Hughes and its sub-contractors will be compliant with this directive and any subsequent revisions or amendments. The European Union (EU) Directive 2002/96/EC on waste electrical and electronic equipment mandates recycling of electrical and electronic equipment throughout the EU by August 13, 2005. Unless otherwise noted, all products, assemblies, and sub-
assemblies manufactured by Hughes and its sub-contractors will be compliant with this directive and any subsequent revisions or amendments. This product carries the WEEE label below to demonstrate compliance. For addition information, contact Hughes Network Systems at:
www.hughes.com. Declaration of Conformity Revision 0.2 47 48 Declaration of Conformity Revision 0.2 APN: An Access Point Name (APN) provides access to an external network. By default, the SIM Card in your terminal is configured with the APN of your Service Provider. You may want to configure further APNs if you have arranged with your Service Provider to use more than one SIM Card. BGAN Satellite Terminal: Referenced throughout this document as the Satellite Terminal, The Terminal, or UT. This device implements and manages BGAN satellite communications between your computer and Service Providers network. Quality of Service: Quality of Service (QoS) assigns a level of priority to certain types of data traffic, in particular high bandwidth applications such as video and multimedia. QoS attempts to maintain a guaranteed throughput level, and minimize error rates and end to end latency, so providing a higher level of service than "best effort" protocols. DNS Server: The Domain Name System (DNS) is an Internet service that is required because the Internet does not recognize the text-based Web address or email address that you type into your Web browser or email application. All or part of a Web address or an email address is a domain name, and DNS translates this domain name into an IP address that is recognized by the Internet. A DNS Server holds a database of domain names and IP addresses, so that when you enter a Web address or email address, you are directed to the correct IP address over the Internet. Ethernet: Ethernet is a local area networking method used widely throughout the computer industry. It is one of the three communications interfaces supported by the Satellite Terminal. Fault Code: A number which uniquely references an error in a hardware or software system. In the Satellite Terminal, if there is a fault detected, the fault code and a description are displayed in suitable LaunchPad windows. GPS: Global Positioning System. The GPS receiver in the Satellite Terminal receives signals from the constellation of GPS satellites. It uses these signals to determine the Terminals location on earth. That location is used during registration to gain access to the BGAN system. Glossary Revision 0.2 49 IP Address: An Internet Protocol address, or IP address, is a number that uniquely identifies the computer accessible over a TCP/IP-based LAN or the Internet that is sending or receiving information. An IP address is a 32-bit numeric address written as four numbers, separated by periods and each number is between 0 and 255. For example, 207.115.79.4 is an IP address. In the BGAN system, IP addresses for the Network and the TE can be dynamic or static. Network Dynamic IP Address: A network dynamic IP address is a temporary address that is assigned by your BGAN Service Provider when you connect to the BGAN Network. Network Static IP Address: If required, a static IP address can be assigned by Service Providers to BGAN users when the SIM is provisioned. This static IP address is used every time you connect to the BGAN network and is associated with a specific username and password. DHCP Address: Local IP address that is assigned by the UT DHCP server to the TE once connected to the UT. This is a private IP address that is not routable within the Internet. Terminal Local IP Address: IP address of the UT to access the web UI and talk to the UT via LaunchPad. This address is configurable by the user. The default local IP address of the terminal is 192.168.128.100
. Standard Connection: A standard connection is charged by volume of data sent. The bandwidth you are allocated depends on terminal type and network availability, but is always best effort, that is, you are allocated bandwidth depending on your requirements and the requirements of other users of the BGAN network, or BGAN Terminal. This connection class is suitable for most data types, other than multimedia. Streaming: A streaming connection gives you a guaranteed data rate and is charged by the amount of time the connection is active. Streams are typically used for multimedia data, such as video. TE (Terminal Equipment): Terminal equipment refers to the piece of equipment that is connected to the BGAN UT (e.g. laptop, video equipment, phone, etc.) Traffic Flow Template: A Traffic Flow Template, also called an Application Template, is a series of data filters such as QoS
(Quality of Service), PDP Context and security settings, that allow the Core Network to classify packets received from an external network into the correct PDP Context. When incoming data arrives at an access point in the core network, a packet 50 Glossary Revision 0.2 classifier will make a PDP Context selection based on the Traffic Flow Template, and map the incoming data packets into the PDP Context with the correct QoS attributes. The use of a Traffic Flow Template allows multiple PDP Contexts to be associated with the same PDP address. UT (User Terminal): The user terminal is the BGAN modem device, i.e. the Hughes 9202. SIM Card: Your BGAN Service Provider supplies you with a Universal Mobile Telecommunications System Subscriber SIM
(SIM) Card. The SIM card is similar to the SIM Card that is commonly used in a GSM phone. The card holds a microchip that stores information and encrypts voice and data transmissions, making it extremely difficult to listen in on calls. The SIM Card also stores data that identifies the caller to the BGAN Service Provider. Virtual Private Network: A Virtual Private Network (VPN) enables remote offices or users to gain secure access to their organization's network over the public telecommunications network. This provides the benefits of remote access without the expense of dedicated leased or owned lines. VPNs work by using tunneling protocols, to encrypt data at the sending end, and decrypt the data at the receiving end. This "tunnel" cannot be accessed by data that is not properly encrypted. Glossary Revision 0.2 51
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2011-07-22 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
2 | JBP - Part 15 Class B Computing Device Peripheral |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2011-07-22
|
||||
1 2 | Applicant's complete, legal business name |
Hughes Network Systems
|
||||
1 2 | FCC Registration Number (FRN) |
0016202228
|
||||
1 2 | Physical Address |
11717 Exploration Lane
|
||||
1 2 |
Germantown, Maryland 20876
|
|||||
1 2 |
United States
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
T******@babt.com
|
||||
1 2 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
1 2 |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
|||||
app s | FCC ID | |||||
1 2 | Grantee Code |
K3Y
|
||||
1 2 | Equipment Product Code |
HNS9202
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
N**** O********
|
||||
1 2 | Title |
Sr. Member Technical Staff
|
||||
1 2 | Telephone Number |
301-6********
|
||||
1 2 | Fax Number |
301-4********
|
||||
1 2 |
n******@hns.com
|
|||||
app s | Technical Contact | |||||
1 2 | Firm Name |
TUV America Inc
|
||||
1 2 |
TUV SUD America Inc
|
|||||
1 2 | Name |
F******** C****
|
||||
1 2 | Physical Address |
10040 Mesa Rim Rd
|
||||
1 2 |
San Diego, California 92121
|
|||||
1 2 |
United States
|
|||||
1 2 | Telephone Number |
+1 85********
|
||||
1 2 |
F******@tuvam.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 01/18/2012 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | DTS - Digital Transmission System | ||||
1 2 | JBP - Part 15 Class B Computing Device Peripheral | |||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Land Portable Terminal | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Original Equipment | ||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Power Output listed is conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 100 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Only the antenna(s) tested in this filing, or similar, may be used with the transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
TUV America
|
||||
1 2 | Name |
S******** D****
|
||||
1 2 | Telephone Number |
848-5******** Extension:
|
||||
1 2 | Fax Number |
848-8********
|
||||
1 2 |
s******@tuvam.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | CC | 2412.00000000 | 2462.00000000 | 0.0152400 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15B | CC |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC