Hui Zhou Gaoshengda Technology Co., LTD W37M2110 WIFI Module IEEE 802.11 b/g/n 2T/2R Model Number: W37M2110 Product Descrition The W37M2110 is a 2.4GHz WIFI 22 MIMO module. This module provides a high level of integration with a dual-stream IEEE 802.11n MAC/ base band /radio.The WLAN operation supports 20MHz,40MHz channels for data rates up to 300Mbps. It fully complies with IEEE 802.11 b/g/n feature rich wireless connectivity at high standards,delivers reliable,cost-effective, throughput from an extended distance. Product Features Complies with IEEE 802.11b/g/n for 2.4GHz Wireless LAN. Two transmit and Two receive path(2T2R) Works with all existing network nfrastructure. Capable of up to 128-Bit WEP Encryption. Freedom to roam while staying connected. UP to 300 Mbps High-Speed Transfer Rate in 802.11n mode of operation. Operating SystemsLinux,Win7, Win8, Win10,XP Low power consumption. Easy to install and configure. High speed USB 2.0 interface ROHS compliant Product Specification Model WIFI Module Product Name W37M2110 Standard Interface 802.11 b/g/n USB Data Transfer Rate 1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,90 and maximum of 300Mbps Modulation Method DQPSK,DBPSK,CCK(802.11b) QPSK,BPSK,16QAM,64QAM with OFDM (802.11g) QPSK,BPSK,16QAM,64QAM with OFDM (802.11n) Frequency Band 2412~2462 MHz Operation Mode Infrastructure Security WEP, TKIP, AES, WPA, WPA2 Operating Voltage 5V10%
Current Consumption 750mA Antenna Type PIFA Operating Temperature 0 ~ 60C ambient temperature Storage Temperature
-40 ~ 80C ambient temperature Humidity 5 to 95 % maximum (non-condensing) NOTICE:
please keep this product and accessories attached to the places which children can't touch;
do not splash water or other liquid onto this product, otherwise it may cause damage;
do not put this product near the heat source or direct sunlight, otherwise it may cause deformation or malfunction;
please keep this product away from flammable or naked flame;
please do not repair this product by yourself. Only qualified personnel can be repaired. PAGE 1 OF 6 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD W37M2110 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. 2.2 This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C (15.247, DTS). It is applicable to the modular transmitter 2.3 This radio transmitter [FCC ID: 2AC23-W37] has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. The concrete contents to check are the following three points.
) Must use antenna such as PIFA antenna with gain not exceeding 4.93dBi;
) Should be installed so that the end user cannot modify the antenna;
) Feed line should be designed in 50ohm Fine tuning of return loss etc. can be performed using a matching network. The antenna shall not be accessible for modification or change by the end user. L'metteur radio FCC id: 2AC23-W37 a t approuv par la FCC Utilisez les types d'antennes numrs ci -
dessous et indiquez le gain maximal admissible. Le gain du type d'antenne non inclus dans cette liste est suprieur au gain maximal de l'un des types numrs et ne doit pas tre utilis avec cet quipement. Le contenu spcifique de l'inspection comprend les trois points suivants.
) Une antenne dont le gain ne dpasse pas 4.93 DBI, telle qu'une antenne pifa, doit tre utilise;
) doivent tre installs de faon que l'utilisateur final ne peut pas modifier l'antenne
) La ligne dalimentation doit tre conue en 50ohm Le rglage prcis de la perte de rendement, etc. peut tre effectu en utilisant un rseau correspondant.. L'utilisateur final ne doit pas modifier ou remplacer l'antenne. 2.4 The module complies with FCC Part 15.247 and apply for single module approval. PAGE 2 OF 6 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD W37M2110 2.5 Trace antenna designs: Not applicable. Any deviation(s) from the defined parameters of the antenna trace, as described by the instructions, require that the host product manufacturer must notify the module grantee that they wish to change the antenna trace design. In this case, a Class II permissive change application is required to be filed by the grantee, or the host manufacturer can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change application. The device must be professionally installed. The intended use is generally not for the general public. It is generally for industry/commercial use. The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not normally required. The user has no access to the connector. Installation must be controlled. Installation requires special training. 2.6 The module is limited to installation in mobile application. Host device must be operated a minimum of 20cm between people. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2.7 Trace antenna designs: Not applicable. Antennas Type and Antenna Gains Antenna No. 0 1 Antenna No. 0 1 Frequency
(MHz) 2412-2462 2412-2462 Frequency
(MHz) 2412-2462 2412-2462 Antenna Group 1 Antenna Type PIFA PIFA Maximum Antenna Gain (dBi) 4.41 4.93 Antenna Group 2 Antenna Type PIFA PIFA Maximum Antenna Gain (dBi) 2.78 3.50 Manufacturer ZHONG TIAN XUN TECHNOLOGY CO., LTD Manufacturer FOXCONN 2.8 Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains FCC ID:2AC23-W37 any similar wording that expresses the same meaning may be used. Canada Statement This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. PAGE 3 OF 6 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD W37M2110 Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage;
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains IC:12290A-W37 any similar wording that expresses the same meaning may be used. l'appareil hte doit porter une tiquette donnant le numro de certification du module d'Industrie Canada, prcd des mots Contient un module d'mission , du mot IC:12290A-W37 ou d'une formulation similaire exprimant le mme sens, comme suit The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'valuation dans la section 2.5 de RSS 102 etla conformit l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne surl'exposition et la conformit de rf. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet metteur ne doit pas tre Co-plac ou ne fonctionnant en mme temps qu'aucune autre antenne oumetteur.Cet quipement devrait tre install et actionn avec une distance minimum de 20 centimtres entre leradiateur et votre corps. This radio transmitter [IC:12290A-W37] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. The concrete contents to check are the following three points.
) Must use antenna such as PIFA antenna with gain not exceeding 4.93dBi;
) Should be installed so that the end user cannot modify the antenna;
) Feed line should be designed in 50ohm Fine tuning of return loss etc. can be performed using a matching network. The antenna shall not be accessible for modification or change by the end user. Le prsent metteur radio [IC:12290A-W37] a t approuv par Innovation, Sciences et Dveloppement conomique Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est suprieur au gain maximal indiqu pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'metteur. Le contenu concret vrifier sont les trois points suivants.
) ) Une antenne dont le gain ne dpasse pas 4.93 DBI, telle qu'une antenne pifa, doit tre utilise;
) doivent tre installs de faon que l'utilisateur final ne peut pas modifier l'antenne
) La ligne dalimentation doit tre conue en 50ohm Le rglage prcis de la perte de rendement, etc. peut tre effectu en utilisant un rseau correspondant.. L'utilisateur final ne doit pas modifier ou remplacer l'antenne. Antennas Type and Antenna Gains PAGE 4 OF 6 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD W37M2110 Antenna No. 0 1 Antenna No. 0 1 Frequency
(MHz) 2412-2462 2412-2462 Frequency
(MHz) 2412-2462 2412-2462 Antenna Group 1 Antenna Type PIFA PIFA Maximum Antenna Gain (dBi) 4.41 4.93 Antenna Group 2 Antenna Type PIFA PIFA Maximum Antenna Gain (dBi) 2.78 3.50 Original Antenna information:
Frequency Antenna
(MHz) No. 2412-2462 0 PCB Antenna Type Maximum Antenna Gain (dBi) 3 1 2412-2462 PCB 3 Manufacturer ZHONG TIAN XUN TECHNOLOGY CO., LTD Manufacturer FOXCONN Manufacturer GSD Notice to OEM integrator Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual(FCC/ICanada statement). Host manufacturer is responsible for compliance of the host system with the module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturers instruction manual. This module is stand-alone modular. If the end product will involve Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, the host manufacturer has to consult with the module manufacturer for the installation method in the end system. Any company of the host device which installs this modular should perform the test of radiated &
conducted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 &
15.207, 15B class B requirement, only if the test result complies with FCC part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement. Then the host can be sold legally. This modular transmitter is only FCC-authorized for the specific rule parts ( 47CFR Part 15.247) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. PAGE 5 OF 6 Version 1.0 Hui Zhou Gaoshengda Technology Co., LTD W37M2110 Must have on the host device a label showing Contains FCC ID: 2AC23-W37 or IC: 12290A- W37 Both FCC ID and IC ID are not to be placed on the host at the same time and only hosts going into the US can use the FCC ID and only hosts going into Canada can use the IC ID. l'hte doit utiliser l'instrument uniquement dans des dispositifs qui rpondent la fcc / (catgorie d'exposition rf mobile, ce qui signifie le dispositif est install et utilis une distance d'au moins 20 cm de personnes. le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen dclarations de conformit relatives l'metteur que de montrer dans ce manuel. le fabricant est responsable de la conformit de l'hte, le systme d'accueil avec le module install avec toutes les autres exigences applicables du systme comme la partie 15 b, ices - 003. accueillir le fabricant est fortement recommand de confirmer la conformit avec les exigences de la fcc /
(metteur lorsque le module est install dans l'hte. le dispositif d'accueil doivent avoir une tiquette indiquant contient FCC ID: 2AC23-W37IC: 12290A-W37 Doit avoir sur l'appareil hte une tiquette indiquant Contient l'ID FCC ID: 2AC23-W37 ou IC : 12290A-W37 L'ID FCC et l'ID IC ne doivent pas tre placs sur l'hte en mme temps et seuls les htes se rendant aux tats-Unis peuvent utiliser l'ID FCC et seuls les htes se rendant au Canada peuvent utiliser l'ID IC. PAGE 6 OF 6 Version 1.0