FCC ID: 2A523S225 Shockwave 200 Wireless Party Speaker

SHOCKWAVE 200 180W IMT7100 IMT7100 SHOCKWAVE 200 180W IMT7100 Quick Start Guide UL Adaptor Brief introduction to buttons on top panel Power Button Press and hold button for 3 seconds to power on or power off speaker Play/Pause (BT mode only), AUX mode: Short press MUTE Previous song Next song Light Modes:

Briefly press to turn on the lighting. Cycles through 9 modes and then back to off Bass Modes:

Briefly press to cycle through 3 bass modes, Standard (flat), Bass Enhance 1 and Bass Enhance 2 FM Mode:

Briefly press to enter into FM mode AUX mode:

Briefly press to enter into AUX mode BT & Party-sync Button:

Briefly press to enter into Bluetooth pairing mode, Press and hold for Bluetooth disconnect, Double-click for party-sync connect or disconnect Reset to default settings:

Press and hold the BASS button for 10S to reset all settings back to factory default. Bluetooth Connection Go to the Bluetooth settings menu on your phone. Make sure that Bluetooth is turned on. Connect to the device listed as AL Shockwave 200 AL Shockwave 200 If needed briefly press the BT button to enter into BT mode;

If you want to change to a different BT device when already paired press and hold the BT button, the speaker will disconnect from its paired device. A different device can now be paired. Party-sync with AL SHOCKWAVE Family AL Shockwave 200 A double press of the BT button is used to enter/exit party-sync mode on extra speakers if you have them as below. Item Number Item name IMT7000 IMT7100 IMT7200 IMT7300 Shockwave Wireless Party Speaker Shockwave 200 Wireless party speaker Shockwave 300 Wireless Party Speaker Shockwave 400 Wireless Party Speaker Pairing Name AL Shockwave AL Shockwave 200 AL Shockwave 300 AL Shockwave 400 The Altec Lansing SHOCKWAVE family has four members that support party-sync. You can mix and match between any of these four models, setting up one speaker as the primary unit connected to up to 100 other speakers all playing in sync. 1. Connect one speaker to your Bluetooth device in the normal way via Bluetooth. 2. Double press the BT button on this first speaker to enter Party sync and make it the primary speaker. 3. Double-press the BT button on the next speaker to enter Party-sync mode, its BT LED will flashes slowly and it will find and connect to the first (primary) speaker. 4. Repeat No 3 if you have more speakers you want to connect. 5. To exit party-sync double press the BT button on the speakers you wish to disconnect and return to normal operation. Notes:

Playback volume is adjusted via the first (primary) speaker. The BT playback controls only operate on the first (primary) speaker. Turning off the first (primary) speaker turns off all speakers. All secondary speakers can be turned on/off individually and their light modes changed via their individual controls. LIGHTING CONTROL Briefly press the LIGHTS button to switch lighting mode.

(Note: Some modes which use sound-to-light need music playing to be visible) Each press moves to the next mode and back round to off. Mode 1: Rotating ring in three colors Mode 2: Flashing to music Mode 3: Spectrum Mode 4: Stacking/re-stacking lights both sides Mode 5: Rotating lights in multi-colors Mode 6: Breathing on/off Mode 7: Flashing to music, solid lighting when no audio Mode 8: Bar-graph in multi-colors Mode 9: Rotating stacking/re-stacking lights INPUT/OUTPUT PORTS Descriptions about the various ports on the speaker Knob to adjust the volume of microphone Input socket for wired microphone USB OUT:

For charging your mobile devices LINE IN (AUX-IN):

For connecting the line level output or headphone output of mobile devices or CD players etc. DC IN:

charging your speaker from the PSU Charging-in indicator:

Solid red when charging, will be off when fully charged RESET:

Button is recessed inside. For use only in the unlikely case of a lock up. Use paperclip or pin to perform restart of the speaker. Power Audio: 180W (Peak) Total Driver Units: 2 x 5.25 Bass + 2 Tweeter. S/N: 70dB Distortion: 0.5%(1K,1W) USB-A output: 5V 1A DC Input: 19V 1.5A Dimensions: L223*H465*D190 mm Length of UL Adaptor cable: 110cm Supplier's Declaration of Conformity 47 CFR 2.1077 Compliance Information Unique Identifier Trade Name: Altec Lansing Model No.: IMT7100 Responsible Party U.S. Contact Information US Company Name: SAKAR INTERNATIONAL INC. Address: Edison, NJ 08817 Telephone number or internet contact information: 855-292-4087 RF Exposure Compliance This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions All the safety and operating instructions should be read before this product is operated. 2.Keep these instructions The safety and operating instructions should be retained for future reference. 3.Heed all warnings All warnings on the appliance and in the operating instructions should be adhered to. 4.Follow all instructions All operating and use instructions should be followed. 5.Do not use this apparatus near water The appliance should not be used near water or moisture for example, in a wet basement or near a swimming pool, and the like. 6.Clean only with dry cloth. 7.Do not block any ventilation openings. Install in accordance with the manufactures instructions. 8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10.Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus. 11.Only use attachments/accessories specified by the manufacturer. 12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13.Unplug the apparatus during lightning storms or when unused for long periods of time. 14.Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15.CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. 16.WARNINGTo reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that objects filled with liquids, such as vases, shall not be placed on apparatus. 17.WARNINGFor the terminals marked with symbol of may be of sufficient magnitude to constitute a risk of electric shock. The external wiring connected to the terminals requires installation by an instructed person or the used of ready-made leads or cords. 18. This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth. ATTENTION:

RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR 19.

- This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

- Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel.

- The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance.

LocationStick it on the back of the device SIZEL50*H40mm 40mm 50mm US 800562 ITEM NO.: IMT7100 PRODUCT DESCRIPTION: Shockwave 200 Wireless Party Speaker DC INPUT: 19V 1.5A MID#3580420 TECH SUPPORT #:1.855.292.4087 MADE IN CHINA FCC ID: 2A523S225 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE , AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. DATE CODE: 04/2022

Applicant Declaration Huizhou Oppen Electronic Technology Co., Ltd Floor 7, 8 and 9 of building 1,2 and 3, No.l9 binhe Avenue, Lilin Town, Zhongkai High-

tech Zone, Huizhou,GuangDong,China GC903042 ___I

: Unled States Applicant Legal Business Name Address Grantee Code FCC ID Contact Email Contact Phone Authorized Contact Name 2A523S225 Nina Kuang tr ade I 6 @flybal l. com. cn 86-13480175391 l, the undersigned, certify that I am an authorized signatory for the Applicant and therefore deciare;

a) in accordance with 47CFR2.91 1(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authorrty of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

(1) labeling the equipmentwith the exact FCC lD as specified in this application,

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC's technical requirements. d) in accordance with 47 CFR 2.909 and KD8394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KD8394321. e) in accordance with 1SO17065, FCC KDB64'! 163, FCC KD8610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing.

(2) the Applicant slrafl make provisions to always have a production sample available upon request by SGS, FCC and/or ISED.

(3) the Applicant sftall, upon request by SGS, at the Applicant's expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. $862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a "par$' for these purposes. S) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, lnc.(TCB) terms and conditions. Link to CFRs:

Link to KDBs:h Link to RSP-1001 Date:2022-4-1

^IJOLE: This deelaralian cannot 8ha o61yrC ya a ,o s ,,e FCC atebase

=ed PersO Applicant Declaration Rev:0.0

Huizhou Oppen Electronic Technology Co., Ltd TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: Confidentiality Request regarding application for FCC lO: 2452115225 LONG TERM CONF:DENT:ALITY Pursuantto 47 CFR Section 0 459 and 0 457 ofthe commisslon's rules the apphcant hereby request confidential treatment ofthe documents listed belovv associated with the certification application referenced above. Schematic(S}

Block D13gr3mS OpeFatiOnal Descriptions The documents above contain proprietary information not released to the pub c Public disclosure of this information may prove harmfulto the business ofthe applicant. SHORTTERM CONF:DENTIALiTY(2eFnark: ,45,9 8o , Additiona y the applicant requests the fo owing documents be held confidential unt the device is marketed or 180 dbys fronn the grant date vvhicheverisless ifthe device is marketed within 180 days ofthe Grant Date the applicant will noufy the TCB per FCC KDB 726920 D01 Conidentiality Request Procedures f194114/flr10:i o iv/Orir J= ry't'ran

'0, External Photos internal Photos Test Setup Photos ser manual(s) Sincerely, Prlnt Signature:

On b hOlf of TitleiSal s l-:e:coo-*

n Electronic Technology Co., Ltd Telephone:86-13480175391 E malli trade16@ yball.CO m.cn

Huizhou Oppen Electronic Technology Co., Ltd Date:2 22-04-01 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MlO2t046 Regarding: FCC lD: 2452:35225 To whom it may concern:

We, the undersigned, hereby authorize Compliance Certification Services (Kunshan) Inc and Kidd yang in Compliance Certification Services (Kunshan) lnc to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC lD above, incldding signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own.. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 19gg, 21 u.s.c. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, lnc., still resides with COMPANY NAME This authorization i notice from the applicant. Title:Sales Electronic Technology Co., Ltd Print Name:

Signature: 4/

On behalf of cO Telephone: 86-1 34801 75391 E-mail: trade16@flyball.com.cn