FCC ID: 2BEO6-U2 Visual online camera

USER GUIDE Welcome to our camera!

Please read the following manual carefully before use to ensure proper operation and product safety. Scan the QR code below to download the V380Pro APP Way of wearing One-piece installation on the right side The battery and the device can be worn on either side Introduction to devices of Online Camera Night Version Light Lens Ventilation Reset hole Eyeglass clip Battery One-click Call TF Card Slot Type-C Port Reset Pin Type-c extension cable Instructions of download the application As shown in the picture, scan the QR code below with your phone to download the app. Install and register. V380 Pro Network Connection and Usage Tutorial Connecting the battery to the camera port, you will hear the prompt "Device is starting, please wait." When you hear "Please scan the QR code on the device using your phone," the device is ready to power on, and you can proceed to the next step for connection. AP Hotspot Mode (Short-range mode) In Nearby Mode, the product can be used without an internet connection, allowing users to view the footage captured by the recorder in real-time. It also enables video recording and photo capture functions. Connect the battery to the camera, the device will automatically power on when plugged in. Please wait until you hear "Please scan the QR code on the device using your phone." The Nearby Mode startup will be successful. Open your phone's Wi-Fi list,Connect to the Wi-Fi signal starting with "HSC_***," for example, "HSC_74205422."

Make sure that your phone's location services are turned on. Open the V380 Pro APP application, on the device list interface, pull down to refresh, and the prompt "Discover Device" will appear. Click on "Add Device." Alternatively, click on "Add Device" and enter the device ID to add it. If the pull-down refresh does not trigger a dialogue box, please check if the network has automatically switched to another Wi-Fi signal. After switching back to the device signal, refresh again and wait for 10 to 30 seconds. After adding the device, you will be prompted to use the local network connection mode. Click "OK" to conrm. The interface will switch to entering the security password. The security password is located beneath the QR code on the back of the device. Please pay attention to dierentiate between uppercase and lowercase letters. Set a new password according to the prompt, and the AP hotspot mode installation will be successful. WiFi Router Mode (Remote Mode) In Remote Mode, you can easily share with multiple users, enabling remote synchronized viewing and intercom functions. You can also view the camera's footage in real-time and utilize video recording and photo capture features. After the device has successfully powered on, open the V380pro APP, click on the top-right corner on the "+" icon, then click on "Add Device."

Scan the QR code on the device to enter the network conguration page. If you don't hear the scanning prompt, long-press the reset hole for 3-5 seconds until you hear "Reset successful." Wait for a few seconds, then, when you hear "Please scan the QR code on the device using your phone," proceed with the operation again. After scanning the QR code, enter the network conguration page. Input the Wi-Fi network name and password you want to use.You can also enter the mobile phone's own hotspot account and password.and once you've conrmed the input is correct, click on "Conrm"

or "OK."

C l i c k h e r e t o c ho o s e d i f f erent W iFi. Use the product to scan the QR code on the phone's screen. When you hear 'You can start using it now,' click 'I hear the success prompt sound. Wait for the device to connect to the network. During this period, avoid clicking

"Back" or performing other operations, as it may result in a failed connection. Once the connection is successful, the page will automatically redirect to the app's home screen. Click the central play button to start viewing the footage captured by the camera. Note on Network Connection Failure:

*If the connection fails, try long pressing the reset button on the camera and attempt to connect again.

*Ensure your phone and Wi-Fi network are functioning properly.

*Verify that the entered password is correct.

*If the connection times out, double-check the Wi-Fi account and password for accuracy. When the Wi-Fi environment changes, it is necessary to reset and restart. Afterward, follow the steps above to reconnect. Team collaboration mode(Remote Mode) This mode enables remote operation guidance functionality, using the mobile hotspot as a WiFi router in remote mode. camera Network Singal Activate H o t s p o t member ' s phone Equivalent to Wi-Fi Router Network Singal C o n n e c t p h o n e L e a d e r

s Pairing Method. camera1 camera2 cameraN

...... Pairing P a i r i n g P a i r i n g p h o n e L e a d e r

s Leader's phone could pair and connect with multiple cameras. camera1 camera2 cameraN H o t s p o t

...... H o t s p o t H o t s p o t p h o n e 2

m e m b e r

s p h o n e N

m e m b e r

s p h o n e 1

m e m b e r

s Team members bring cameras when going out. L e a d e r

s p h o n e The camera captures images/footage from camera1. The camera captures images/footage from camera 2. The camera captures images/footage from camera N. camera1 camera2 cameraN Just the leader's mobile phone can view the scenes captured by each team member's camera,but the member's phone cant see the viewing by their own mobile phone. p h o n e 1

m e m b e r

s p h o n e 2

m e m b e r

s

...... p h o n e N

m e m b e r

s s h are s h are s h a r e p h o n e L e a d e r

s Leader's mobile phone share the member's camera viewing to their mobile phones separately ,and let them to see it. Other Features One-click call. Press the one-touch call button on the camera to send a notification to the leader's phone. Share Device Both the main phone and the shared phone need to be registered with an account in V380 pro. .. Click the menu button , then select 'Share.' Enter the friend's account and proceed to add the sharing . Remove Device Click the menu button , then select 'Delete' to remove the device or reinstall if necessary. .. Settings The specic settings for the camera, such as changing password, recording, alarm, language, IP, etc. Memory Card When inser ting the memor y card, ensure the gold contacts are facing down and insert it into the card slot.When installing or removing the TF card, make sure to disconnect the camera's power first. Please use a TF card produced by a reputable manufacturer, with a minimum read/write speed of U1/Class 10. While it is possible to use the camera without a TF card, it won't save videos, and the playback feature will be disabled. It is recommended to install a TF card for optimal usage. The playback function requires disconnecting and reconnecting the power for the first use to display. Cloud Storage Binding A cloud storage plan can only be linked to one camera device. Fault Diagnosis Video Lag/Network Connection Failure The remote monitoring is not smooth. Check the current network status and select the appropriate resolution based on the current network environment. Ensure that the network is normal in the installation environment, especially outdoors. Check whether the Wi-Fi coverage is adequate, place the device close to the Wi-Fi router, and verify the correctness of the Wi-Fi account and password. If forget password If you accidentally forget the password, please long-

press the device reset hole to restore factory settings and reinstall the login password. Temperature Instructions:

The On-line camera will emit heat during use, which is normal and will not aect the functionality. Installation Instructions:

Please read the user manual for installation guidance carefully. If you are not sure, feel free to contact with our customer service. Other Notes:

Due to iterative updates, dierences in packaging appearance and operational features in the manual are considered normal. Disclaimer 1. Any accidents and resulting losses caused using the product are not the responsibility of our company, and we do not assume any legal liability for such incidents. 2. This product is strictly prohibited from being illegally modied and should not be used for shooting, producing, copying, publishing, disseminating, or engaging in any illegal content with reactionary, pornographic, violent, obscene, voyeuristic, or similar nature. If you violate the law in this regard, our company declares no legal responsibility for such actions. 3. This product solely provides a platform for image display and communication. We are not responsible for the accuracy, authenticity, legitimacy, or legality of its content, and we do not assume any legal responsibility. 4. Any organization or individual who believes that the use of this product may infringe upon their image rights, our company assumes no legal responsibility for such claims. 5. This product is intended solely for normal operation, device maintenance, and similar auxiliary uses. We disclaim any responsibility for any illegal activities and assume no legal liability. Specications Product model U2 Size 95mm 18mm 14mm

Weight 27g(Excluding clip) FPS (Frames per second) 1280 720P25 FPS

Streaming H.264 Recording Field of View (Horizontal) 72 Effective night vision distance Number of Night Version Lights WIFI Fixed Frequency Loop Recording Function Daytime Vision Recording Power Consumption Night Vision Recording Power Consumption Audio Pickup Distance 3~5meters 4pcs F3 940nm Infrared Lights 2.4G Available 210mAh at 5V 310mAh at 5V 3~5meters Speaker Available Wi-Fi Connection Range Point-to-Point Distance Within 30 meters (open with out interference or obstruction) Within 30 meters (open with out interference or obstruction) Video Format AVI Brand Groudchat Machine Body QR Code and Password Very Important! Please Keep FCC warning 1. This device should be installed and operated with minimum distance 20cm between the radiator&your body. 2. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. 3. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 4. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. interference

Huizhou Xincheng Optoelectronics Co., Ltd. Building B, Floor 3, Juye Company, No. 50 Community, Pingnan Industrial Zone, Zhongkai High tech Zone, Huizhou, Guangdong Province, China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-1-24 To whom it may concern:

We, Huizhou Xincheng Optoelectronics Co., Ltd., hereby certify that the equipment for which authorization is sought (FCC ID: 2BEO6-U2) is not covered equipment prohibited from receiving an equipment authorization pursuant to 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, we are not identified on the Covered List (https://www foc. gov/supplychain/coveredlist) as an entity producing covered equipment. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.914(b) and (4)(5) and (6). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 DO1 Sincerely, Ak Mu Signature Aizhen Niu Manager Huizhou Xincheng Optoelectronics Co.,Ltd.

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2024-1-24>

Pursuant to Paragraphs 0.457 and 0.459 of the Commission's Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:

FCC ID Model name 2BEO6-U2 U2 For the product stated above, we request that the following information be held confidential;

Long-Term Exhibits Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos, Block Diagram Schematics Test Setup Photos User's Manual Parts List Tune Up OOOO RRoO) Operational Descriptions. Dopooo8o5) The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device If you have any questions, please feel free to contact me at the address shown below. Sincerely, Abd Aizhen Niu/Manager Huizhou Xincheng Optoelectronics Co., Ltd, Building B, Floor 3, Juye Company, No. 50 Community, Pingnan Industrial Zone, Zhongkai High tech Zone, Huizhou, Guangdong Province, China 13266549672 13266549672@163.com

Huizhou Xincheng Optoelectronics Co., Ltd. Building B, Floor 3, Juye Company, No. 50 Community, Pingnan Industrial Zone, Zhongkai High tech Zone, Huizhou, Guangdong Province, China Date: 2024-1-24 FCC ID: 2BEQ6-U2 Model Number: U2 To:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD To Whom It May Concern, We, Huizhou Xincheng Optoelectronics Co., Ltd., declare that this EUT (FCC ID:

2BEO6-U2) doesnt have Ad Hoc mode function on non-US/Canada frequencies. In addition. The frequency selection feature is disabled by firmware for devices marked to the US/Canada. For DTS part of this device, only channels 1-11 will be used in North America, Country code selection is disabled. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely, AbMs Name/Title: Aizhen Niu/Manager Company: Huizhou Xincheng Optoelectronics Co., Ltd. Address: Building B, Floor 3, Juye Company, No. 50 Community, Pingnan Industrial Zone, Zhongkai High tech Zone, Huizhou, Guangdong Province, China Phone: 13266549672 Fax:

E-mail: 13266549672@163.com

Huizhou Xincheng Optoelectronics Co., Ltd. Building B, Floor 3, Juye Company, No. 50 Community, Pingnan Industrial Zone, Zhongkai High tech Zone, Huizhou, Guangdong Province, China Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2024-1-24 To whom it may concern:

We, the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behaffin all matters relating to applications for equipment authorization FCC ID: 2BEO6-U2 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins current valid General Terms and Conditions

(AGB),Testing and Certification Regulations (PZO) which can be viewed on following website wwweurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 Sincerely,

Ab. A. Name/Title: Aizhen Niu/Manager Company: Huizhou Xincheng Optoelectronics Co., Ltd. Address: Building B, Floor 3, Juye Company, No. 50 Community, Pingnan Industrial Zone, Zhongkai High tech Zone, Huizhou, Guangdong Province, China Phone: 13266549672 Fax:

E-Mail: 13266549672@163.com

Huizhou Xincheng Optoelectronics Co., Ltd. Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 U.S. Agent Designation 1/23/2024 Huizhou Xincheng Optoelectronics Co., Ltd. acknowledges their consent for the following contact located in the United States to act as their agent for service of process for the equipment for which authorization is sought

(FCC ID: 2BEO6-U2):

Name and company of U.S. agent:

SELLER HELPER INC Physical U.S. address of agent:

1312 17th Street#1298, Denver, CO 80202, Jnited States FRN of U.S. agent:

Email address of U.S. agent:

0033406737 sellerhelper@sellerhelper.top SELLER HELPER INC acknowledges their obligation to accept service of process on behalf of Huizhou Xincheng Optoelectronics Co., Ltd. Huizhou Xincheng Optoelectronics Co., Ltd. Ltd.with the FRN 0034785584. accepts its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. By signing this form, we confirm the above and that we are aware of the application requirements listed under 2.911(d)(7). The information provided in this letter is based on the referenced rule parts of Title 47 of the CFR as well as KDB 986446 D01. An expiration date for this letter does not exist. In case the U.S. agent changes, the grantee is obligated to notify the FCC within 30 days via the granting TCB. Sincerely, Signature

[Name] Aizhen Niu

[Title] Manager

[Company] Huizhou Xincheng Optoelectronics Co., Ltd.

[Name of U.S. agent] Fairy Lee

[Title of U.S. agent] Manager

[Company of U.S. agent] SELLER HELPER INC 5 0 V

, U

) 7

) d

1 1 9

. 2 _ t n e g A _ S U

l e d o m

_ 8 4