3000 wireless video transmission system supporting HDMI & SDI
(VAXIS STORM3000) FCC ID:2AJOF-3000 User manual 1. Cautions ..................................................................................................1 2. About.......................................................................................................2 3. Installation.............................................................................................10 4. Operation instruction ............................................................................11 5. Maintenance..........................................................................................14 6. Trouble shooting ...................................................................................15 1. Cautions Logo and meaning Careful, warning, dangerous, Pay attend to following items. Cautions Do not use this product in the extreme hot, cold, dusty or humid environments. Prevent friction with hard objects. Avoid the product falling down from a high place, or it may damage the hardware. The product is not water proofed. So do not get any liquid into the unit please. Do not dismantle, assemble or alter the product arbitrarily. 2. About Product model and standard The VAXIS STORM3000 Wireless HDMI/SDI Transmission Suite utilize todays most advanced wireless video transmission technology, which can realize the broadcast-class and uncompressed 3G SDI/HDMI HD video signal transmitted with no compression and zero delay. The suite includes one transmitter and one receiver, where the transmitter provides a 3G/HD SDI input and a HDMI input, and the receiver also provides a 3G/HD SDI output and a HDMI output. The wireless HD suite has 2 stick antennas in transmitter side, and 5 stick antennas in receiver side, and it can work in 5.1-5.9GHz frequency band and be flexibly software configured to licensed or ISM band of global different regions, as well as the side panel of both transmitter and receiver have been installed a control panel with OLED, which provides maximum 5 workable frequency channels, and supports maximum 10 sets working simultaneously. The wireless suite can accept wide range DC power input, which is suitable for many kinds of camera battery model. The suite also can sustain 8 kV ESD (HBM, contact discharge), the industry class metal case and professional heat design would guarantee most robust reliability. Main features:
HDMI 1.3 spec supports HDMI and 3G SDI input and output 24fps frame rates Highest resolution 1080p 60no delay and no compression Support audio formats include Dolby True HD, DTS-master, etc. AES-128 encryption with air interface HD video data stream Support point to point, and point to multi points network topology 5GHz ISM frequency bandmaximum 10 frequency channels selected by user knob, coexist with WIFI. Maximum transmission distance 3000 Mounting: Sony U-30 / Canon LP-E6 / Sony NP-970 battery plate Embedded time code transported over link Up to 63mW RF Power output: Up to 63mW,no harm to human health Signal indicators for wireless power status, Temperature, Video status and receiver RSSI, useful OLED display and channel setting by tact switch Wide range power voltage input , adapt most kinds of camera battery Any input and output ports with 6 kV ESD protection level (HBM, contact discharge) All-metal housing, durable Pure hardware connection; Plug and Play USB firmware upgrade Parameters:
Transmitter Receiver Interface SDI InputBNC Female; SDI loop out SDI Output X 2BNC Female; HDMI BNC Female; HDMI Input(Type A Output(Type A female); 5 Antenna female); 2 Antenna port(2 SMA male;
port(SMA male; DC input (2 pin LEMO DC input (2 pin LEMO female) female) Supply voltage range 6-36V DC Power consumption
<6.5W 6-36V DC
< 6 W Size Mass
(L x W x H): 131x 69 x 27mm,
(L x W x H): 135x 92 x 27mm, dont include antennas dont include antennas 290g 480g Input Video Format HDMI 525i, 625i, 720p
/
50/59.94/60,1080i 50/59.94/60,1080p23.98/24/25/29.9/30/5 0/59.94/60HDMI Type A SDI 3G, HD, and SD-SDI
(auto-selected), SMPTE-259/274/292/296/372/424/425 1x BNC Output Video Format SDI Loop out;
HDMI 525i, 625i, 720p 50/59.94/60,1080i 50/59.94/60,1080p23.98/24/25/29.9/30/5 0/59.94/60HDMI Type A SDI 3G, HD, and SD-SDI
(auto-selected), SMPTE-259/274/292/296/372/424/425 2x BNC Input Audio Format SDI embedded 4 channel 24 bit/48KHz
/
Output Audio
/
SDI embedded 4 channel 24 bit/48KHz Signal Indicator OLED display OLED display Frequency Band 5.1-5.9GHz configurable with China, 5.1-5.9GHz configurable with China, North American, Europe, etc North American, Europe, etc Modulation Mode OFDM 16QAM OFDM 16QAM Transmission Power Maximum 18dBm for FCC Receiver Sensitivity
/
Occupied Bandwidth 40MHz
/
-75dBm 40MHz Temperature Range 0 ~
40C
(operating condition);
0 ~
40C
(operating condition);
-20~60C(Storage)
-20~60C(Storage) FCC; CE. Compliance FCC; CE. Product introduction Transmitter:
10 OLED Screen Channel Button +
Channel Button - *Long press the buttons to adjust the Fan DC power switch HDMI Input USB debugging interface 3G SDI Output 3G-SDI Input Antenna interface DC input, LEMO 2-pin B series connector Receiver:
DC power switch HDMI Output 3G-SDI Output1 3G-SDI Output2 Antenna interface HDMI Output Channel Button +
Channel Button -
USB debugging interface DC input, LEMO 2-pin B series connector Screen Operation:
Temperature display Fans speed display Channel display Signal strength display Signal source display Signal input format display 0`S function Battery voltage display Packing list:
1x unit Transmitter 1x unit Receiver 7x 5GHz sword Antennas 2x DC convert cable (LEMO 2 pin-male to D-Type receptacle) 1x 1/4-20 screw to ISO518 hot-shoe converter 1x 7 Articulating magic arm 1x User Manual VAXIS flight case 3. Installation Installation details and cautions Transmitter side a) Install 2 Omni-directional and high efficiency antennas to Transmitters SMA male antenna connectors. b) There are 3 1/4-20 screw nuts in transmitter metal case, which are located on the bottom. So the user can utilize a 1/4 screw to ISO518 hot-shoe converter fix the transmitter on camera. c) The user can also utilize a subsidiary LEMO 2 pin male to D-Type receptacle power cable to get power input from an outside power source. Receiver side a) Install 5 pcs Omni-directional and high efficiency antennas to receivers SMA male antenna connectors. b) The user can utilize a subsidiary LEMO 2 pin-male to D-Type receptacle power cable to get power input from an outside power source. c) The user can also utilize the Battery plate accessory Sony U-39 or Sony NP-970 to connect the power source. Typical connection instruction Connect camera SDI or HDMI output to transmitter SDI or HDMI input port, and the transmitter can fixed in hot-shoe port of the camera. Connect HDMI or SDI output port of the receiver to SDI or HDMI input port of the HD monitor. Make sure all antennas, batteries and Video cable are equipped normally. 4. Operation instruction Getting started After finishing all steps above, system is workable, follow below steps. a) Ensure the video source output of the camera is OK, and the HD monitor is power on and switched to connected video input port. b) Ensure all input, output SDI or HDMI cables are connected. c) Ensure all antennas are installed, and it is better to keep TX 2 antennas and RX 5 antennas with orthogonal angle each other for best RF performance. d) Ensure both the transmitter and receiver installed batteries or DC input ports connected to outside power sources. Then toggle power switch of transmitter and receiver to ON respectively, then Power screen will be light. e) Ensure the frequency knobs of transmitter and receiver are set with the same number, and this will make sure the transmitter and receiver work with same RF frequency. f) If the camera is on and video input is OK, TX side video screen will be light. g) Before RX finished wireless link with TX, the Recievers OLED Screen is not display; when wireless link is OK, the Recievers OLED Screenwill display, and will indicate the received RF signal strength. If the receiver detects normal wireless video internally from air interface, then the will light. Before that, if SDI or HDMI video out port of the receiver has HD monitor connected, it will display an OSD of Link connecting like below picture. h) The system will spend about 20 seconds on constructing communication link, and real link period will depend on the current wireless channel condition. When wireless link is set up, will display wireless signal strength, as well will light, means had receive the normal signal; then connected HD monitor will display the HD video and audio from TX module. relevant is also i) For the best wireless transmission performance, it need install the transmitter and receiver more than 1.5m about the ground and keep the same height, and make sure no obstacles between them;
Moreover, it is the best to keep the transmitter antennas face to face, and dont turn round any sides with too big angle. The real transmission distance to current air electromagnetic environment, because the system works in ISM band, it is exposure to all kind od 5GHz band air interference, we suggest the users should do a manual frequency sweep by adjusting frequency selection knob with a circle before using the equipment, then choose the best frequency channel for stable performance. Input video port selection of transmitter The transmitter has a 3G SDI video input port and a HDMI video input port, and the system will detect valid video source automatically of SDI and HDMI port, and then switch it as main video input channel. If both SDI and HDMI have valid video inputs, the system will take SDI input as priority. RSSI indicators Strength The receiver will calculate received RF signal strength internally and The OLED Screen will indicate wireless signal power and quality. The user can observe the OLED Screen status to know if the current wireless link is reliable or not. Signal indication 4-5 2-3 1 or no lit LED Frequency selection and configuration Best Good Visible Video Noise Wireless quality Strong Middle Weak Video Quality Link The wireless suite can work in 5.1-5.9GHz frequency band and be flexibly software configured to licensed or ISM band of global different regions. Meanwhile, on the front of both transmitter and receiver have OLED Screen, press the Green Button - and Button + to adjust the channel. Please note: Transmitter and Receiver should keep in the same channel. It provide maximum 10 workable frequency channels, and support maximum 10 sets working simultaneously. 5. Maintenance Storage conditions Products storage temperature should be -20C~60C. For long time storage requirement, please use original carbon boxes, and avoid from high humid, acid base or dusty place. Maintenance Warning To ensure your safety, place choose well-known brand DC batteries, and guarantee suitable work conditions that battery manual mentioned. 6. Trouble shooting Normal problems a) No output on display Check TX and RX power first, and see if TX or RX is powered from external power, then check if TX antennas and RX antennas are installed right. After that, check the Transmitters , if TX is not light, then check SDI or HDMI cable is plugged in and video source is ready please. Finally may check input video format is compatible with this product specs. b) Poor output video quality Check if SDI or HDMI input or output cable is plugged well, then checks the status of wireless signal strength , there should be at least 2-3 frames lit if the user want to get better video quality; if there is only 1 frames lit, that means the received wireless signal is weak, and should shorten the transmission distance. FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, Human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation