FCC ID: 2A5AE-BDG010 Hand IQ Badge

Outside 1 (back) Outside 2 (back) Outside 3 (back) Outside 4 (Front) Important product and safety information Product specifications and FCC compliance FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC SHOCK OR OTHER INJURY OR DAMAGE. BATTERY SAFETY HANDLE WITH CARE. Your Hand IQ Hub device contains a rechargeable lithium-ion (Li-ion) polymer battery. Do not disassemble or attempt to access the battery in your device. Do not modify or remanufacture the battery, attempt to insert foreign objects into the battery, or immerse or expose it to water or other liquids, expose it to fire, explosion or other hazards. Use of an unqualified battery or charger may present risk of fire, explosion, leakage or other hazard. Your Hand IQ Hub device uses a USB-C power adaptor intended to be used with your Hand IQ Hub device. This power adapter is intended for indoor use only. Your Hand IQ Handwash Sensors contain a single disposable 3V coin cell lithium battery (model CR2477). Never charge the battery as it is not designed to be rechargeable, and this may cause leakage or explosion. Battery is operational with its positive side facing upwards and negative side facing into the equipment. Never short circuit, heat, incinerate or dismantle the battery. Caution: Keep away from children and pets. RECYCLING YOUR DEVICE PROPERLY. In some areas, the disposal of certain electronic devices is regulated. Make sure you dispose of, or recycle, your devices in accordance with local laws and regulations. TERMS OF USE AND POLICIES. Hand IQ Hub and Hand IQ Smart Sensors are Hygiene IQ Devices. Please read all terms and usage policies, which can be found at www.handiq.com LIMITED WARRANTY. Your new Hand IQ devices are covered by a one year Limited Warranty. Please read all warranty information, which can be found at www.handiq.com FAQ and support Visit: https://handiq.com/customer-support BDG010 & SSR010 meets the FCC & IC requirements for RF exposure in public or uncontrolled environments BDG010 & SSR010 Cet appareil est conforme aux conditions de la IC en matire de RF dans des environnements publics ou incontrle Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s)]. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes: (1) lappareil ne doit pas produire de brouillage, et (2) lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. The party responsible for FCC compliance is Hygiene IQ, LLC 636 Moulton Ave., Los Angeles, CA 90031 USA. If you wish to contact Hygiene IQ, please visit www.handiq.com/customer-support. Device Name: Hand IQ Hub Contains FCC ID: 2AC7Z-ESP32WROOM32E Handwash measurement made easy 2022 Hygiene IQ, LLC or its Affiliates Hand IQ, and all related marks are trademarks of Hygiene IQ, LLC or its affiliates. Quick start guide and product information Need to update to reasonable daily wash count, e.g. 97. inside 1 inside 2 inside 3 inside 4 Get to know Hand IQ Hub screen and Handwash Sensor LED indicators Getting started Attach your handwash sensors Handwash Hub Handwash Sensor Hub Screen Prepare the hardware You want to keep your ring full throughout the day. The daily handwash activity ring is based on the number of people in your shared areas and the handwash goals you set. Slide the wall mount behind the hub down and then push the power button Good Average Below average Countdown Unscrew the back of the sensor counter clockwise, then take out the coin cell battery and flip over. You should see a blue LED flicker on the front of the sensor Begin by removing the double stick tape backing on the handwash sensor mount plate, then follow the instructions below to install it on pump or automatic dispensers. Once the sensors are attached, you can finish setup in the mobile app. Pump Automatic Handwash goals can be ambitious. When youre in the blue, youre good Average is not bad, but there are risks associated with not meeting your stated goals Red means pick up the pace and encourage more handwashing for the safety of everyone A 20-second timer with handwash prompts helps staff when placed near a dispenser Handwash Sensor LEDs Log into the Hand IQ Mobile App and choose the location where you will activate the hardware

*Note Hand IQ requires a basic subscription. Go to www.handiq.com for pricing 16 Download the Hand IQ Mobile App for iOS or Android. Blue flicker Handwash Sensor is unassigned Choose how frequently you want people to wash hands at your location Singled blue flash Handwash Sensor vibration detection activated (pump dispensers) Active your Hub and connect it to Wifi For pump dispensers place the handwash sensor on the outside or inside of the dispenser. The sensor will pick up the pumping motion when someone is activating the dispenser. For automatic dispensers, place the sensor right under the dispenser on the wall. The sensor needs to be within a few inches of a hand when activating the dispenser. Mounting your hub Mount the hub in a central area by a wall plug where staff can see it, preferably by a handwash sink. (If near a handwash sensor, it will display a countdown.) Remove the wall plate on the back of the hub. You can either use the double stick tape or screw it to the wall. Single green flash Handwash Sensor motion detector activated (touch-free dispensers) Add your handwash sensors Scan to download the app Plug your hub in using the provided USB-C charger Battery indicator Daily wash activity ring

+ optional countdown Daily wash count USB-C Charge Port Hub Back Wall mount Power button

(under wall mount) Front of sensor

+ LED Back of sensor

+ mount plate Wall Charger USB-C Overall, were looking for an outline style for the images. The color used is up to the designer, but it should be supported by our colors (i.e. the blue that we use) This is cord outline is the style we are going for with all the drawings. Images of front and back of sensor should not be at an angle UNLESS the designer feels this adds to the overall design. If the designer goes for this, they will need to do the same with the hub. Note the colors above are what we are using for our rings. Blue: #3CB7E8;

Yellow:#FDCF08; Red: #ED5D78 The above QR code is dynamic and will be updated once we have the app on the app store. Use the same picture from inside 1 panel to show the mount. Would be cool if it was plugged in. Note the automatic sensor above I moved the sensor close underneath. I also removed the soap nossels to make this work. Actual cord shape / design

(doesnt need to be wrapped this way) Actual back of hub w/ wall mount plate inserted. Also, note there is no beltline on the circumfrence like in the original design.

D C B A 4 3 2 1 REVISIONS DESCRIPTION INITIAL RELEASE DATE 4/6/2022 ZONE REV. A B A2, B1 MADE SNAP DETAILS SMALLER - ADDED FCC INFO 4/20/2022 Notes 1. 2. 3. 4. 5. MATERIAL: POLYCARBONATE COLOR: TRANSLUCENT BLACK - COLOR CHIPS TO BE APPROVED BEFORE T1 TEXTIRE:

1. 2. 3. SNAPPING FEATURE MUST BE ON INSERT - SHEET 2 SHOWS DETAILS GOLDEN SAMPLES MUST BE APPROVED BY HANDIQ BEOFORE PRODUCTION START RED - MT11010 GREEN - NO GATES, EJECTION PINS MUST GO NEGATIVE ALL OTHER SURFACE CAN BE MACHINE FINISH 7.05 76.20 2 X 3 A 36.55 1 2.20 4.30 0.87 B 5.15 70.74 B GATE MUST BE TRIMMED FLUSH DETAIL A SCALE 8 : 1 4 3 UNLESS OTHERWISE SPECIFIED:

NAME DATE DIMENSIONS ARE IN MM DRAWN CHECKED ENG APPR. MFG APPR. Q.A. COMMENTS:

INTERPRET GEOMETRIC TOLERANCING PER:

MATERIAL PC FINISH NEXT ASSY USED ON TOLERANCES, UNLESS OTHERWISE SPECIFIED 0 - 15 MM 15 - 50 MM 50 - 100 MM 100 - 200 MM 200 - 300 MM 300 - 400 MM

>400 MM ANGLES 0.05 MM 0.10 MM 0.15 MM 0.20 MM 0.25 MM 0.30 MM 0.35 MM 0.5 PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF

<INSERT COMPANY NAME HERE>. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF

<INSERT COMPANY NAME HERE> IS PROHIBITED. 2 BADGE V2 BACK A DWG. NO. REV A TITLE:

SIZE C 1 APPLICATION DO NOT SCALE DRAWING SCALE: 2:1 WEIGHT:

SHEET 1 OF 2 D C B D C B A 4 3 2 1 B SNAPPING FEATURE WILL NEED TO BE UPDATED DURING DEBUG. AREA NEEDS TO BE ON AN INSERT. THE FEATURE IS SYMMETRIC, TWO INSERTS WILL BE NECESSARY SNAPPING FEATURES DETAIL B SCALE 10 : 1 D C B 4 3 UNLESS OTHERWISE SPECIFIED:

NAME DATE DIMENSIONS ARE IN INCHES TOLERANCES:

FRACTIONAL ANGULAR: MACH TWO PLACE DECIMAL THREE PLACE DECIMAL BEND INTERPRET GEOMETRIC TOLERANCING PER:

MATERIAL PC FINISH DRAWN CHECKED ENG APPR. MFG APPR. Q.A. COMMENTS:

TITLE:

SIZE C 1 NEXT ASSY USED ON APPLICATION DO NOT SCALE DRAWING SCALE: 2:1 WEIGHT:

SHEET 2 OF 2 DWG. NO. REV B BADGE V2 BACK A PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF

<INSERT COMPANY NAME HERE>. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF

<INSERT COMPANY NAME HERE> IS PROHIBITED. 2

Letter of Authorization and Anti- Drug Statement Hygiene IQ LLC Address:

636 Moulton Ave Los Angeles CA, 90031 Product Name:

Model Number:

FCC ID:

We authorize:

HandIQ Badge BDG010 2A5AE-BDG010 CETECOM Inc., to act on our behalf on all matters concerning the above named equipment. We declare that CETECOM Inc. is allowed to forward all information related to the approval project to the Federal Communications Commission and discuss any issues concerning the approval application. The applicant must certify that neither the applicant nor any party to the application is subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-

Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47 CFR 1.2002(b) for the definition of a "party" for these purposes. Does the applicant or authorized agent so certify? Yes I certify that I am authorized to sign this application. All of the statements herein and the exhibits attached hereto, are true and correct to the best of my knowledge and belief. In accepting a Grant of Equipment Authorization as a result of the representations made in this application, the applicant is responsible for (1) labeling the equipment with the exact FCC ID specified in this application, (2) compliance statement labeling pursuant to the applicable rules, and (3) compliance of the equipment with the applicable technical rules. If the applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC's technical requirements. Authorizing an agent to sign this application, is done solely at the applicant's discretion;

however, the applicant remains responsible for all statements in this application. If an agent has signed this application on behalf of the applicant, a written letter of authorization which includes information to enable the agent to respond to the above section 5301 (Anti-Drug Abuse) Certification statement has been provided by the applicant. It is understood that the letter of authorization must be submitted to the FCC upon request, and that the FCC reserves the right to contact the applicant directly at any time. Signature of Authorized Person Filing:

Title: CTO Date: April 11th 2022

Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21048 Date: April 12th 2022 Subject:

To Whom It May Concern:

In accordance with 0.457(d) and 0.459 of CFR 47, and KDB 726920, Hygiene IQ LLC hereby requests permanent confidentiality for documents filed under the following exhibit types:

Request for Permanent Confidentiality FCC ID: 2A5AE-BDG010 1. Block Diagram 2. Schematic Diagram 3. Part List 4. Operational Description These items contain detailed system and equipment description and related information about the product which Hygiene IQ LLC considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, Hygiene IQ LLC also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. We are aware that exhibit types cover letters, attestations, label document, test reports, RF exposure information (SAR and MPE reports), cannot be requested to be classified confidential and are thus subject to publication, as will be documents of all other exhibits types for which we have not requested a confidentiality classification. Best Regards, _______________________________ Signature Name:

Title:

Company Name:

Address:

Richard Adams Chief Technology Office Hygiene IQ LLC 636, Moulton Ave., Los Angeles, CA, 90031. USA

Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21048 Date:

Subject:

To Whom It May Concern:

14th April 2022 Request for Short Term Confidentiality FCC-ID: 2A5AE-BDG010 In accordance with 0.457(d) and 0.459 of CFR 47, Hygiene IQ LLC hereby requests short term confidentiality for documents filed under the following exhibit types:

1. External Photographs 2. Internal Photographs 3. User / Instruction Manual 4. Test Set-up Photographs until the product will be publicly announced. Short term confidentiality release date / period:

days These items contain detailed system and equipment description and related information about the product which Hygiene IQ LLC considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, Hygiene IQ LLC also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. 180 so that date the short We are informed and aware of our obligation that we have to inform the involved TCB in written and in due time if we intend to market the product prior to the above specified confidentiality release product launch. We are aware that exhibit types cover letters, attestations, label document, test reports, RF exposure information (SAR and MPE reports), cannot be requested to be classified confidential and are thus subject to publication, as will be documents of all other exhibits types for which we have not requested a confidentiality classification. confidentiality classification reset prior term can be to Best Regards, ____________________________________ Signature Name:

Title:

Company Name:

Address:

Richard Adams CTO Hygiene IQ LLC 636 Moulton Ave, Los Angeles, CA, 90031