BD50X DIGITAL PORTABLE RADIO QUICK REFERENCE GUIDE Product Overview Product Layout Programmable Key For enhanced convenience, you can request your dealer to program SK as a shortcut to a radio feature. Consult your dealer for assignable radio features. 1 LED Indications LED Indicator Radio Status Flashes green The radio is being turned on. Glows green The radio is receiving. Glows red The radio is transmitting. Flashes orange slowly The radio is scanning. Glows orange Call hang time: No voice is being transmitted or received on the channel during a call. Within such a period, you can press and hold the PTT key and speak. Basic Operations Charging the Battery l Read the Safety Information Booklet before charging. l Use the approved charger to charge the battery. l The remaining lithium-ion battery power is limited to 30% pursuant to the new lithium battery shipment regulation approved by International Air Transport Association (IATA). 2 Before initial use, make sure to charge the battery. You can charge either the standalone battery or the radio with battery attached. It is recommended that the radio remain powered off during charging. The LED indicator on the charger shows the charging status. For details, see the following table. LED Indicator Charging Status Glows red The battery is being charged. Glows orange The battery is charged to 85% or more. Glows green charged. No battery is placed on the charger, or the battery is fully Turning the Radio On or Off To turn the radio on or off, rotate the On-Off/Volume Control knob clockwise or counter-clockwise until you hear a click. Adjusting the Volume To increase or decrease the volume, rotate the On-Off/Volume Control knob clockwise or counter-clockwise. Selecting a Zone A zone is a group of channels within the same operational area. The radio If the Channel Notify feature is enabled, the radio automatically announces initiate a call to a private or group contact. supports up to 3 zones, each of which contains up to 16 channels. To select a zone, press the preprogrammed Zone Up or Zone Down key. Selecting a Channel To select a channel, rotate the Channel Selector knob. the current channel upon power-on and channel change. Call Services When you are speaking during a call, keep the microphone about 2.5 to 5 cm away from your mouth. This ensures optimal voice quality on the receiving radio. Call on Digital Channel You can initiate or receive the following types of calls on a digital channel:
l Private call: a call from an individual user to another individual user. l Group call: a call from an individual user in a group to all the other members in the group. l All call (enabled by your dealer): a call from an individual user to all other users on the current channel. Initiating a Call l On the home screen, rotate the Channel Selector knob to select the required channel, and then press and hold the PTT key to initiate a call to the private/group/all call contact preset on the channel. l If the One Touch Call feature is configured by your dealer, press the preprogrammed One Touch Call key, and then press the PTT key to Receiving and Responding to a Call You can listen to an incoming call without any operation. To respond to a private or group call, press and hold the PTT key within the preset time. Ending a Call l A private/group call ends when the call hang time expires. l An all call ends when the calling party releases the PTT key. Call on Analog Channel (Without Signaling) You can initiate a call to all other users on the current analog channel. The operations are the same as those on digital channel. For details on more features and operations, please visit our website at: http://www.hytera.com, or scan the QR code to download the User Manual. 3 SK 1 PTT LED l l l IATA 2016 2 30%
LED 85%
l l 3 16
l l PTT l PTT PTT l /PTT
l PTT 2.55 3 http://www.hytera.com Frequency Ranger: 400-470MHz Output Power: 36dBm(high),30dBm(Low) AT EE HU LU SK RO BE FI IE MT SI HR CY FR IT NL ES CZ DE LV PL SE DK EL LT PT BG 4 FCC/ISEDC Statement This device complies with part 15 of the FCC/ISEDC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme la partie 15 des rgles FCC/ISEDC. Lopration est soumise aux deux conditions suivantes :
(1) Cet appareil ne peut pas causer dinterfrences nocives et (2) cet appareil doit accepter toute interfrence reue, y compris toute interfrence susceptible de provoquer un fonctionnement indsirable. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Toute modification ou modification non expressment approuve par la partie responsable de la conformit pourrait annuler le pouvoir de lutilisateur dexploiter lquipement. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC/ISEDC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Cet quipement a t test et sest avr conforme aux limites dun appareil numrique de classe B, conformment la partie 15 des rgles de la FCC/
ISEDC. Ces limites sont conues pour fournir une protection raisonnable contre les interfrences nocives dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre de lnergie par radiofrquence et, sil nest pas install et utilis conformment aux instructions, peut causer des interfrences nocives aux communications radio. Toutefois, il ny a aucune garantie que des interfrences ne se produiront pas dans une installation particulire. Si cet quipement cause des interfrences nuisibles la rception de la radio ou de la tlvision, qui peuvent tre dtermines en teignant et en allumant lquipement, lutilisateur est encourag essayer de corriger linterfrence par une ou plusieurs des mesures suivantes :
Rorienter ou dplacer lantenne de rception. Augmenter la sparation entre lquipement et le rcepteur. Connectez lquipement dans une prise sur un circuit diffrent de celui auquel le rcepteur est connect. Consultez le concessionnaire ou un technicien expriment en radio/tlvision pour obtenir de laide. Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure avec la distance de l'antenne.l'antenne doit se tenir loin du visage et des yeux. occupational/controlled environmental exposure limits, the product. RF Exposure Compliance and Control Guidelines and Operating Instructions To control your exposure and ensure compliance with the always adhere to the following procedures. Guidelines:
Do not remove the RF Exposure Label from the device. User awareness instructions should accompany device when transferred to other users. Do not use this device if the operational requirements described herein are not met. Operating Instructions:
Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) key. To receive calls, release the PTT key. Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy only when transmitting
(in terms of measuring for standards compliance). Keep the radio unit at least 2.5 cm away from the face. Keeping the radio at the proper distance is important as RF exposure decreases with distance from the antenna. The antenna should be kept away from the face and eyes. When worn on the body, always place the radio in a Hytera-approved holder, holster, case, or body harness or by use of the correct clip for this product. Use of non-approved accessories may result in exposure levels which exceed the FCC's occupational/controlled environmental RF exposure limits. guidelines. Contact your local dealer for the optional accessories of L'exposition aux champs rf de conformit et de contrle d'orientations et instructions avec l'exposition et s'assurer de limites la Pour contrler conformit d'exposition professionnelle / environnement contrl, toujours respecter les procdures suivantes. Lignes directrices:
les Ne pas enlever l'tiquette de l'appareil d'exposition aux radiofrquences. Sensibilisation des utilisateurs instructions devraient accompagner dispositif lorsque transfrs d'autres utilisateurs. Ne pas utiliser cet appareil si les exigences oprationnelles dcrites ci - aprs ne sont pas remplies. Les instructions de fonctionnement:
Transmettre non plus que le facteur d'utilisation nominal de 50% du temps. transmettre (parler), pousse le pousse parler (ptt). Pour recevoir des appels, les ptt.50% du temps de transmission, ou moins, est important parce que la radio gnre de l'nergie rf seulement lors de la transmission des (en termes de mesure de la conformit aux normes). Ie groupe de la radio continue d'au moins 2,5 cm de la la bonne distance est surface.garde important, car l'exposition aux champs rf diminue la radio Quand ports sur le corps, toujours place de la radio dans un tui, hytera approuv titulaire, ou un harnais ou par l'utilisation de la vido pour ce produit.utilisation des accessoires non approuvs peuvent entraner des fac qui dpassent les niveaux d'exposition professionnelle et environnementale contrle des limites d'exposition aux rf. Les oprations doivent satisfaire aux deux conditions suivantes:
Ce dispositif peut ne pas causer d 'interfrences nuisibles. Ce dispositif doit accepter toute interfrence reue, Y compris les interfrences qui peuvent provoquer des accidents.Operation Non approuv des antennes, les piles et les accessoires causes la radio dpasser les lignes directrices sur l'exposition aux radiofrquences de fac. Communiquez avec votre distributeur local pour les accessoires facultatifs du produit. ISEDC Statement The device has been tested and complies with SAR limits, users can obtain Canadian information on RF exposure and compliance Aprs examen de ce matriel aux conformit aux limites DAS, et/ou aux limites dintensit de champ RF, les utilisateurs peuvent sur lexposition aux radiofrquences et la conformit and compliance dacqurir les informations correspondantes SAR tests are conducted using standard operating positions accepted by the FCC/ISEDC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. Before a new model device is a available for sale to the public, it must be tested and certified to the FCC/ISEDC that it does not exceed the exposure limit established by the FCC/ISEDC, Tests for each device are performed in positions and locations (worn on the body)as required by the FCC/ISEDC. For face-up, 25mm was used for test, this equipment should be installed and operated with minimum distance 25mm. For body worn operation, this model phone has been tested and meets the FCC/ISEDC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that Contains no metal and that positions the handset a minimum of 0mm from the body. Non-compliance with the above restrictions may result in violation of RF exposure guidelines. Les essais SAR sont effectus laide de positions dexploitation normalises acceptes par la FCC/ISEDC avec lappareil transmettant son niveau de puissance certifi le plus lev dans toutes les bandes de frquences testes, bien que le SAR soit dtermin au niveau de puissance certifi le plus lev, le niveau rel de R-S de lappareil pendant son fonctionnement peut tre bien infrieur la valeur maximale. Avant quun nouveau dispositif de modle ne soit disponible la vente au public, il doit tre test et certifi la FCC/ISEDC quil ne dpasse pas la limite dexposition tablie par la FCC/ISEDC, les tests pour chaque appareil sont effectus dans des positions et des emplacements (ports sur le corps) comme lexige la FCC/ISEDC. Pour le face-vers le haut, 25mm a t utilis pour lessai, cet quipement doit tre install et actionn avec une distance minimale de 25mm. Pour le fonctionnement du corps us, ce tlphone modle a t test et rpond aux directives dexposition RF FCC/ISEDC lorsquil est utilis avec un accessoire dsign pour ce produit ou lorsquil est utilis avec un accessoire qui ne contient pas de mtal et qui positionne le combin dun minimum de 0mm du corps. Le non-respect des restrictions ci-dessus peut entraner une violation des lignes directrices sur lexposition aux RF. is the trademark or registered trademark of Hytera Communications Corporation Limited. 2018 Hytera Communications Corporation Limited. All Rights Reserved. Address: Hytera Tower, HiTech Industrial Park North, 9108# Beihuan Road, Nanshan District, Shenzhen, People's Republic of China,P.R.C,P 518057 Postcode: 518057 http:// www.hytera.com 2018 9108 518057 400-830-7020 http://www.hytera.com Z17714 L32733 Z04313 5 2 0 2 0 1 0 0 6 0 8 3 1 A