all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Users Manual | Users Manual | 2.40 MiB | ||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | Internal Photos | |||||||
1 | Cover Letter(s) | |||||||
1 | Test Setup Photos | |||||||
1 | Test Report |
1 | Users Manual | Users Manual | 2.40 MiB |
DS-6210U5C4 Base Station Owner's Manual Version: V00 Release Date:Oct., 2012 Owner's Manual Contents Contents 1. Checking Items in the Package .......................................................................................................... 8 2. Product Controls .................................................................................................................................. 9 2.1 Interface Units of 4-carrier Base Station .......................................................................................... 9 2.1.1 Antenna Connector ............................................................................................................... 10 2.1.2 EIB ........................................................................................................................................ 10 2.1.3 Power Supply Interface ........................................................................................................ 12 2.2 Cartridge ......................................................................................................................................... 13 2.3 Channel Unit (CHU) ........................................................................................................................ 13 2.3.1 Function ................................................................................................................................ 13 2.3.2 Front Panel ........................................................................................................................... 14 2.3.3 LED Indicator ........................................................................................................................ 15 2.4 Base Station Controller Unit (BSCU).............................................................................................. 16 2.4.1 Function ................................................................................................................................ 16 2.4.2 Front Panel ........................................................................................................................... 17 2.4.3 LED Indicator ........................................................................................................................ 18 2.5 Power Supply Unit (PSU) ............................................................................................................... 19 2.5.1 Function ................................................................................................................................ 19 2.5.2 Front Panel ........................................................................................................................... 20 2.5.3 LED Indicator ........................................................................................................................ 21 2.6 Interconnect Backboard (ICB) ........................................................................................................ 22 2.6.1 Front View ............................................................................................................................ 22 2.6.2 Rear View ............................................................................................................................. 23 2.7 FAN ................................................................................................................................................. 25 2.7.1 Front Panel ........................................................................................................................... 25 2.7.2 LED Indicator ........................................................................................................................ 25 2.7.3 Rear Panel............................................................................................................................ 26 2.8 Divider Unit (DIU) ............................................................................................................................ 27 2.8.1 Function ................................................................................................................................ 27 2.8.2 Front Panel ........................................................................................................................... 27 2.8.3 Rear Panel............................................................................................................................ 28 2.9 Router ............................................................................................................................................. 29 2.9.1 Function ................................................................................................................................ 29 2.9.2 Front Panel ........................................................................................................................... 29 2.9.3 Rear Panel............................................................................................................................ 30 2.9.4 LED Indicator ........................................................................................................................ 30 i Contents Owner's Manual 2.10 IP-E1 ............................................................................................................................................. 31 2.10.1 Front Panel ......................................................................................................................... 31 2.10.2 LED Indicator ...................................................................................................................... 32 2.10.3 Rear Panel.......................................................................................................................... 33 2.11 Combiner (COM) .......................................................................................................................... 33 2.11.1 Function .............................................................................................................................. 34 2.11.2 Rear Panel .......................................................................................................................... 34 3. Installation ........................................................................................................................................... 36 3.1 Cable Layout ................................................................................................................................... 36 3.2 Safety Information........................................................................................................................... 36 3.2.1 Power Supply ....................................................................................................................... 37 3.2.2 Working at Heights ............................................................................................................... 37 3.3 Installation Preparation ................................................................................................................... 37 3.3.1 Technical Files ...................................................................................................................... 37 3.3.2 Personnel ............................................................................................................................. 38 3.3.3 Tools ..................................................................................................................................... 38 3.4 Unpacking Inspection ..................................................................................................................... 39 3.4.1 Check before Unpacking ...................................................................................................... 39 3.4.2 Unpacking Wooden Case..................................................................................................... 39 3.4.3 Unpacking Cartons ............................................................................................................... 40 3.4.4 Inspections ........................................................................................................................... 41 3.5 Installing the Cabinet ...................................................................................................................... 41 3.5.1 Determine the Installation Position ...................................................................................... 41 3.5.2 Installing the Cabinet ............................................................................................................ 42 3.6 Installing Modules into the Cabinet ................................................................................................ 43 3.6.1 Module Layout ...................................................................................................................... 43 3.6.2 Installation Procedures ......................................................................................................... 43 3.7 Installing Cables ............................................................................................................................. 47 3.7.1 Equipment Status ................................................................................................................. 47 3.7.2 Cables .................................................................................................................................. 47 3.8 Examination after Installation ......................................................................................................... 49 3.8.1 Equipment Status ................................................................................................................. 49 3.8.2 Examining the Cabinet ......................................................................................................... 49 3.8.3 Examining Cables ................................................................................................................ 49 3.8.4 Power On and Examination ................................................................................................. 50 3.8.5 Environment Examination .................................................................................................... 50 4. Basic Operations ................................................................................................................................ 52 ii Owner's Manual Contents 4.1 Powering on .................................................................................................................................... 52 4.2 Powering off .................................................................................................................................... 52 5. Troubleshooting ................................................................................................................................. 53 6. Routine Maintenance ......................................................................................................................... 54 6.1 Purpose........................................................................................................................................... 54 6.2 Tasks .............................................................................................................................................. 54 A Abbreviations ...................................................................................................................................... 55 iii Figures Owner's Manual Figures Figure 2-1 Interface Units of 4-carrier Base Station .................................................................................. 9 Figure 2-2 Antenna Connector of 4-carrier Base Station ......................................................................... 10 Figure 2-3 EIB of 4-carrier Base Station ................................................................................................... 11 Figure 2-4 Power Supply Interface of 4-carrier Base Station .................................................................. 12 Figure 2-5 Full Configuration for MC ........................................................................................................ 13 Figure 2-6 Logical Architecture of CHU ................................................................................................... 13 Figure 2-7 Front Panel of CHU ................................................................................................................ 14 Figure 2-8 Logic Architecture of BSCU .................................................................................................... 16 Figure 2-9 Front Panel of BSCU .............................................................................................................. 17 Figure 2-10 Front Panel of PSU ............................................................................................................... 21 Figure 2-11 Front View of ICB .................................................................................................................. 23 Figure 2-12 Rear View of ICB .................................................................................................................. 24 Figure 2-13 Front Panel of FAN ............................................................................................................... 25 Figure 2-14 Rear Panel of FAN ................................................................................................................ 26 Figure 2-15 Logical Diagram of DIU ........................................................................................................ 27 Figure 2-16 Front Panel of DIU ................................................................................................................ 27 Figure 2-17 Rear Panel of DIU................................................................................................................. 28 Figure 2-18 Front Panel of Router ........................................................................................................... 29 Figure 2-19 Rear Panel of Router ............................................................................................................ 30 Figure 2-20 Front Panel of IP-E1 ............................................................................................................. 32 Figure 2-21 Rear Panel of IP-E1 .............................................................................................................. 33 Figure 2-22 Logical Diagram of 4-port Combiner .................................................................................... 34 Figure 2-23 Rear Panel of COM .............................................................................................................. 34 Figure 3-1 Cable Layout ........................................................................................................................... 36 Figure 3-2 Removing the Cover ............................................................................................................... 40 Figure 3-3 Layout of holes for a Single Cabinet ...................................................................................... 41 Figure 3-4 Layout of holes for Combined Cabinet ................................................................................... 42 Figure 3-5 Tightening the Bolt .................................................................................................................. 42 Figure 3-6 of Module Layout .................................................................................................................... 43 Figure 3-7 Opening the Cabinet Door ...................................................................................................... 44 Figure 3-8 Disassembling the Side Door ................................................................................................. 44 Figure 3-9 Loosening the Ejector ............................................................................................................. 45 Figure 3-10 Installing the BSCU............................................................................................................... 45 Figure 3-11 Installing the FAN .................................................................................................................. 46 Figure 3-12 Removing the FAN................................................................................................................ 46 iv Owner's Manual Figures Figure 3-13 Installing the Divider Unit ...................................................................................................... 46 Figure 3-14 Installing the Combiner Unit ................................................................................................. 47 Figure 3-15 Cable Diagram ...................................................................................................................... 47 Figure 3-16 External Cable Connection ................................................................................................... 48 v Tables Owner's Manual Tables Figure 1-1 Packing List .............................................................................................................................. 8 Table 2-1 Descriptions on Interface Units of 4-carrier Base Station ........................................................ 10 Table 2-2 Descriptions on Antenna Connector of 4-carrier Base Station ................................................ 10 Table 2-3 Descriptions on EIB of 4-carrier Base Station .......................................................................... 11 Table 2-4 Descriptions on Power Supply Interface of 4-carrier Base Station .......................................... 12 Table 2-5 Description on Front Panel of CHU .......................................................................................... 15 Table 2-6 Descriptions on CHU Indicators ............................................................................................... 16 Table 2-7 Descriptions on Front Panel of BSCU ...................................................................................... 18 Table 2-8 Descriptions on BSCU Indicators ............................................................................................. 19 Table 2-9 Descriptions on PSU ................................................................................................................ 20 Table 2-10 Descriptions on Front Panel of PSU ...................................................................................... 21 Table 2-11 Descriptions on PSU Indicators.............................................................................................. 22 Table 2-12 Descriptions on Front Interfaces of ICB ................................................................................. 23 Table 2-13 Descriptions on Rear Interfaces of ICB.................................................................................. 24 Table 2-14 DIP Switch Settings for ICB ................................................................................................... 25 Table 2-15 Descriptions on FAN Indicators .............................................................................................. 26 Table 2-16 Descriptions on Rear Panel of FAN ....................................................................................... 26 Table 2-17 DIP Switch Settings for FAN .................................................................................................. 27 Table 2-18 Descriptions on Front Panel of DIU ....................................................................................... 28 Table 2-19 Descriptions on Rear Panel of DIU ........................................................................................ 28 Table 2-20 DIU Address Settings ............................................................................................................. 29 Table 2-21 Descriptions on Front Panel of Router ................................................................................... 29 Table 2-22 Descriptions on Rear Panel of Router ................................................................................... 30 Table 2-23 Descriptions on Router Indicators .......................................................................................... 31 Table 2-24 Descriptions on IP-E1 Indicators ............................................................................................ 32 Table 2-25 Descriptions on Rear Panel of IP-E1 ..................................................................................... 33 Table 2-26 Descriptions on Rear Panel of COM ...................................................................................... 35 Table 3-1 Technical Files .......................................................................................................................... 38 Table 3-2 Tools and Meter ........................................................................................................................ 38 Table 3-3 Cables Description ................................................................................................................... 48 Table 3-4 Descriptions on the interface of external cable connection ..................................................... 48 Table 3-5 Checklist of Cabinet Installation ............................................................................................... 49 Table 3-6 Checklist of Cables ................................................................................................................... 50 Table 3-7 Checklist of Power Situation .................................................................................................... 50 Table 3-8 Checklist of Environment on Site ............................................................................................. 51 vi Owner's Manual Tables Table 5-1 Troubleshooting ........................................................................................................................ 53 vii Checking Items in the Package Owner's Manual 1. Checking Items in the Package Item Qty. (PCS) Base Station Controller Unit (BSCU) Channel Unit (CHU) Power Support Unit (PSU) Fan Unit Divider Unit (DIU) Combiner Unit (COM) Cabinet Kit Figure 1-1 Packing List 1 4 2 1 1 1 1 No. 1 2 3 4 5 6 7 8 Owner's Manual 2. Product Controls Note Devices except for CHU, BSCU, PSU and ICB are optional. Product Controls 2.1 Interface Units of 4-carrier Base Station The interface units on the top of the cabinet consist of the antenna connector, extended interface board (EIB) and power supply interface. See Figure 2-1. Figure 2-1 Interface Units of 4-carrier Base Station Name Description Antenna Connector It contains the GPS antenna connector, RX antenna No. 1 9 Product Controls Owner's Manual No. Name Description connector and TX antenna connector. 2 3 EIB It contains the core network interface, cabinet expansion interface and monitor interface. Power Supply Interface
Table 2-1 Descriptions on Interface Units of 4-carrier Base Station 2.1.1 Antenna Connector The antenna connector is illustrated below. Figure 2-2 Antenna Connector of 4-carrier Base Station No. Name Description 1 2 3 Antenna TX Connector Antenna RX Connector GPS Antenna Connector TX/RX N-connector (female) RX1 RX2 RX3 GPS1 GPS2 N-connector (female) N-connector (female) Table 2-2 Descriptions on Antenna Connector of 4-carrier Base Station 2.1.2 EIB The EIB is illustrated below. 10 Owner's Manual Product Controls Figure 2-3 EIB of 4-carrier Base Station No. Name Description E1-TX1 E1-RX1 E1-1 E1-2 E1-TX2 E1-RX2 BNC-connector (female) BNC-connector (female) DB9-connector (female) DB9-connector (female) BNC-connector (female) BNC-connector (female) AUX Dedicated 72-pin interface LAN1 LAN2 CAN RJ-45 connector RJ-45 connector DB9-connector (female) RS485 DB9-connector (female) Table 2-3 Descriptions on EIB of 4-carrier Base Station 1 E1 Interface Cabinet Expansion Interface Ethernet Interface Monitor Interface 2 3 4 11 Product Controls Core Network Interface Owner's Manual The core network interface contains the 4-path E1 interface and 2-path Ethernet interface. Cabinet Expansion Interface The cabinet expansion interface has 8-path extended signals. It is applied to connect to four interconnect relay units of another cabinet, in case of interconnecting two cabinets. Monitor Interface The monitor interface includes one CAN-BUS interface and one RS485 interface. 2.1.3 Power Supply Interface The power supply interface is illustrated below. Figure 2-4 Power Supply Interface of 4-carrier Base Station No. 1 3 5 Name Ground Bar AC Input Terminal SPD Breaker No. 2 4 6 Name AC Input Breaker Surge Protection Device (SPD) AC Output Terminal Table 2-4 Descriptions on Power Supply Interface of 4-carrier Base Station 12 Owner's Manual Product Controls 2.2 Cartridge In accordance with the IEC60297 standard, the cartridge is 19 inches in width and 7U in height. Each cartridge can accommodate four CHUs, two BSCUs and two PSUs. The slot 5 and slot 6 of the main chassis are available for the BSCU. See Figure 2-5. C H U C H U C H U C H U B S C U B S C U P S U P S U 01 02 03 04 05 06 07 08 Figure 2-5 Full Configuration for MC 2.3 Channel Unit (CHU) The CHU logically includes power amplification, TX excitation unit, baseband signal processing unit and diversity receiver. See Figure 2-6. TX Antenna PA TX Excitation Unit Baseband Signal Processing Unit Power ICB RX Antenna 1 RX Antenna 2 RX Antenna 3 Diversity Receiver Figure 2-6 Logical Architecture of CHU 2.3.1 Function The CHU processes and converts protocols on the physical layer and data link layer of the DMR air interface. Physically, it consists of channel control board (CHB), TX board (TXB) and RX board (RXB). 13 Product Controls Owner's Manual CHB: capable of signaling processing, channel encoding/decoding, interleaving and de-interleaving, modulation/demodulation, RF signal loop-back test and fail-soft. TXB: capable of modulation, upward frequency conversion, filtering and D/A conversion from carrier baseband signal to RF signal, as well as the downlink signal amplification. RXB: capable of filtering, demodulation, downward frequency conversion, AGC and A/D conversion from three-path carrier signal to baseband signal, as well as uplink signal amplification. 2.3.2 Front Panel The front panel of the CHU is illustrated below. Figure 2-7 Front Panel of CHU No. Name Description Remarks 1 RXA Diversity RX antenna input SMA-connector (female) 14 Owner's Manual Product Controls No. Name Description Remarks 2 3 4 5 6 RXB RXC LEDs RS232 TX RX antenna input SMA-connector (female) Diversity RX antenna input SMA-connector (female) LED indicator
Debug interface DB9-connector (female) Transmission N-connector (female) Table 2-5 Description on Front Panel of CHU 2.3.3 LED Indicator The CHU indicators are described in Table 2-6. LED Indicator Color Status Description (in working mode) Description (in sleep mode) PWR Green RUN Green TX Green RX Green ALM Red PLL Red On The CHU is powered on. The CHU is powered on. Off The CHU is powered off. The CHU is powered off. Flashing The CHU runs properly.
Off The CHU does not run properly. The CHU is in sleep mode. On Off On Off On Off On Data is present on downlink slot 2 of the CHU.
Data is present on downlink slot 1 of the CHU. The CHU is in sleep mode. Data is present on the uplink of the CHU. Data is present on the uplink of the CHU. No data is present on the uplink of the CHU. No data is present on the uplink of the CHU. The CHU software is faulty. The CHU software is faulty. The CHU runs properly. The CHU runs properly. An alarm is given for PLL unlock. An alarm is given for PLL 15 Product Controls Owner's Manual LED Indicator Color Status Description (in working mode) Description (in sleep mode) unlock. Off The CHU runs properly. The CHU runs properly. Table 2-6 Descriptions on CHU Indicators Note In sleep mode, the CHU can receive inbound data. However, if the downlink channel is in use, the CHU will turn to operation mode; if the downlink channel is released, the CHU will turn to sleep mode. 2.4 Base Station Controller Unit (BSCU) The BSCU logically consists of GPS board, main control board, synchronizing buffer, Ethernet switch, micro processor unit and power supply. See Figure 2-8. GPS VGA USB RS232 RS232 BSCU-GPSB GPS Board Synchronizing Buffer CLKCNT BSCU-MCB Main Control Board Ethernet Switch MPU Micro Processor Unit Power Supply LAN1
... LAN11 CAN RS-485 DC-IN BSCU ICB Figure 2-8 Logic Architecture of BSCU 2.4.1 Function The BSCU is to manage the wireless link resources within the coverage and allocate them for different call services. 16 Owner's Manual 2.4.2 Front Panel The front panel of the BSCU is illustrated below. Product Controls Figure 2-9 Front Panel of BSCU No. Name Qty. Description Description Video graphics array USB Interface RS232 Interface 1 2 3 17 1 For debugging DB15-connector (female) 4 1 For debugging A-connector (female) For debugging DB9-connector (male) Product Controls Owner's Manual No. Name Qty. Description Description 4 5 6 RST Key LEDs SMA Interface 1 1 1 BSCU reset LED indicator
GPS signal input SMA-connector (female) Table 2-7 Descriptions on Front Panel of BSCU 2.4.3 LED Indicator The BSCU indicators are described in Table 2-8. LED Indicator Color Status Description PWR Green On Off The BSCU is powered on. The BSCU is powered off. Flashing rapidly The BSCU is working in master mode. RUN Green Flashing slowly The BSCU is working in slave mode. GPS Green ALM Red Off The BSCU is being initialized or malfunctions. Flashing Functions are disabled locally. On Off On Off On Functions are disabled via GPS. Functions are enabled via GPS. The BSCU is alarming. The BSCU works properly. The link between BSCU and CHU is present. CHU1~4 Green Flashing Data is being transmitted or received over the link between BSCU and CHU. Off The link is abnormal or not connected between BSCU and CHU. On The link between BSCU and IRU is present. Flashing Data is being transmitted or received over the link IRU1~3 Green 18 Owner's Manual Product Controls LED Indicator Color Status Description between BSCU and IRU. Off On The link is abnormal or not connected between BSCU and IRU. The link between the standby BSCU and active BSCU is present. BAK Green Flashing Data is being transmitted or received over the link between the standby BSCU and active BSCU. Off The link is abnormal or not connected between the standby BSCU and active BSCU. On The link between BSCU and MCB is present. MCB Green Flashing Data is being transmitted or received over the link between BSCU and MCB. Off The link is abnormal or not connected between BSCU and MCB. On The link between BSCU and LNA is present. LAN1~2 Green Flashing Data is being transmitted or received over the link between BSCU and LAN. Off The link is abnormal or not connected between BSCU and LAN. Table 2-8 Descriptions on BSCU Indicators 2.5 Power Supply Unit (PSU) The PSU consists of power monitor board, power module and LED indicators. 2.5.1 Function Functions are described in Table 2-9. 19 Product Controls Owner's Manual No. Item Description 1 2 3 4 5 6 7 External Power Supply Input 90~264V AC 47~63Hz Voltage Output device)
(for main 13.5V DC Voltage Output (for CHU PA) HVCC (13.5V DC) Voltage Output CHU power supply)
(for other LVCC (13.5V DC) Voltage Output (for BSCU) BSC_V (13.2V DC) I/O Interface Monitor Interface It is connected to 2 BSCUs and outputs three channel signals. The first two are used for resetting PSU, and the last for installation status of PSU. It is connected to 2 BSCUs. It is connected to 2 BSCUs. Table 2-9 Descriptions on PSU 2.5.2 Front Panel The front panel of the PSU is illustrated below. 20 Owner's Manual Product Controls Figure 2-10 Front Panel of PSU No. 1 2 Name LEDs ON/ OFF Switch Qty. 1 1 LED indicator Power switch Description Table 2-10 Descriptions on Front Panel of PSU 2.5.3 LED Indicator The PSU indicators are described in Table 2-11. LED Indicator Color Status Description Glowing solidly A major alarm exists. ALM Red Flashing A minor alarm exists. Off No alarm exists. 21 Product Controls Owner's Manual LED Indicator Color Status Description PWR1 Green PWR2 Green Glowing solidly The first power module outputs normally. Flashing slowly The first power module outputs HVCC or LVCC alarm. Flashing rapidly The first power module outputs HVCC and LVCC alarm simultaneously. Off The first power module is not installed. Glowing solidly The second power module outputs normally. Flashing slowly The second power module outputs HVCC or LVCC alarm. Flashing rapidly The second power module outputs HVCC and LVCC alarm simultaneously. Off The second power module is not installed. Glowing solidly The voltage for the BSC is normal. BSC Green Flashing An alarm is issued due to over-voltage or low voltage for the BSC. Off The first or second power module is not installed. Table 2-11 Descriptions on PSU Indicators Note The power module has two outputs including HVCC and LVCC. 2.6 Interconnect Backboard (ICB) It connects the power, synchronization clock module, signaling gateway, voice and data gateway, monitor module and I/O interface. 2.6.1 Front View The front side and interfaces of the ICB are described below. 22 Owner's Manual Product Controls Figure 2-11 Front View of ICB No. Name Qty. Description 1 2 3 CHU Interface BSCU Interface PSU Interface 4 2 2 For signal from CHU to ICB. For signal from BSCU to ICB. For signal from PSU to ICB. Table 2-12 Descriptions on Front Interfaces of ICB 2.6.2 Rear View The rear view and interfaces of the ICB are described below. 23 Product Controls Owner's Manual No. Name Qty. Description Figure 2-12 Rear View of ICB 1 2 3 4 5 6 7 8 Monitor Interconnection Interface EC Interface EIB Interface DC Power Inlet AC Power Inlet Power Outlet DIP Switch Monitor Interconnection Interface 2 2 6 1 1 6 1 2 CAN-BUS, DB9-connector (male/female) For interconnecting two cartridges in the cabinet. For interconnecting two EC cartridges and four IRUs between two cabinets. It also works as the signal interface from EIB to ICB in the core network interface board. DC power input: -48V AC power input: 110V/220V DC power (+13.2V) for FAN and DIU. For setting the cartridge address. RS485 bus, DB9-connector (male/female) Table 2-13 Descriptions on Rear Interfaces of ICB 24 Owner's Manual The settings of the DIP switch are described in Table 2-14. Product Controls No. 1 2 3 4 4 X X 3 ON ON 2 X X 1 Description Note ON Address for the main chassis OFF Address chassis for the first extended X OFF X ON Address for the second extended chassis X: reserved. X OFF X OFF for the third extended Address chassis Table 2-14 DIP Switch Settings for ICB 2.7 FAN The FAN consists of a fan cartridge and a pluggable fan tray, and can accommodate six fans. In the fan tray, three temperature sensors are installed. 2.7.1 Front Panel The front panel of the FAN is illustrated below. Figure 2-13 Front Panel of FAN 2.7.2 LED Indicator The FAN indicators are described in Table 2-15. Name Color Status Description On Off On Off The FAN is powered on. The FAN is powered off. The fan works properly. The fan is out of operation or not installed. PWR Red 1~6 Green 25 Product Controls Owner's Manual Name Color Status Description Flashing The fan is faulty. Table 2-15 Descriptions on FAN Indicators 2.7.3 Rear Panel The rear panel of the FAN is illustrated below. Figure 2-14 Rear Panel of FAN No. Name Qty. Description 1 2 3 4 5 6 RS485 Monitor Interface DIP Switch Power Inlet 1 Power Inlet 2 Monitor CAN Interface Ground Interface 2 1 1 1 2 1 For connecting
(male/female) ICB and DIU. DB9-connector For setting the FAN address. For details, please refer to Table 2-17. For connecting ICB. For connecting ICB. ICB and DIU. DB9-connector For connecting
(male/female)
Table 2-16 Descriptions on Rear Panel of FAN The settings of the DIP switch are described in Table 2-17. No. 1 2 1 X X 2 X X 3 ON 4 Description Remarks ON The first FAN address OFF ON second The address FAN X: reserved. 26 Owner's Manual Product Controls No. 3 4 1 X X 2 X X 3 4 Description Remarks ON OFF The third FAN address OFF OFF fourth The address FAN Table 2-17 DIP Switch Settings for FAN 2.8 Divider Unit (DIU) The DIU is 3U or 1U in height. The logical diagram is shown below. RX RX RX RX RX RX RX RX Band-pass Filter LNA Digital Attenuator Power Divider CAN/RS485 Figure 2-15 Logical Diagram of DIU 2.8.1 Function The DIU is to assign the received signal to each transceiver. 2.8.2 Front Panel The front panel of the DIU is illustrated below. Figure 2-16 Front Panel of DIU 27 Product Controls Owner's Manual No. Name Qty. Description Remarks 1 2 3 RXA RXB RXC 8 8 8 Diversity RX antenna output SMA-connector (female) RX antenna output SMA-connector (female) Diversity RX antenna output SMA-connector (female) Table 2-18 Descriptions on Front Panel of DIU 2.8.3 Rear Panel The rear panel of the DIU is illustrated below. Figure 2-17 Rear Panel of DIU No. Name Qty. Description Remarks DIP switch Monitor interface Monitor interface Power inlet
Diversity RX antenna A N-connector (female) RX antenna B N-connector (female) Diversity RX antenna C N-connector (female) Ground interface Table 2-19 Descriptions on Rear Panel of DIU 1 2 3 4 5 6 7 8 SWITCH RS485 CAN-BUS PWR RXA RXB RXC 1 2 2 1 1 1 1 1 28 Owner's Manual The settings of the DIU address are described in Table 2-20. Product Controls No. 1 2 3 4 1 ON ON 2 ON OFF OFF ON OFF OFF 3 X X X X 4 X X X X Description Remarks The first DIU address The second DIU address The third DIU address The fourth DIU address X: reserved. Table 2-20 DIU Address Settings 2.9 Router 2.9.1 Function The router is a device that forwards message flow or packet data. However, if the IP-EI is employed, no router will be required. 2.9.2 Front Panel The front panel of the router is illustrated below. Figure 2-18 Front Panel of Router Name No. Name No. Name Power Switch USB Interface 2 5 Power Socket RESET Button 3
LEDs
Table 2-21 Descriptions on Front Panel of Router No. 1 4 29 Product Controls 2.9.3 Rear Panel The rear panel of the router is illustrated below. Owner's Manual Figure 2-19 Rear Panel of Router No. Name No. Name 1 3 5 7 Ground Terminal Fixed Ethernet Interface 0 Fixed Switch Interface 2 Fixed Switch Interface 4 2 4 6 8 Console
(CON/AUX)
/Auxiliary Interface Fixed Switch Interface 1 Fixed Switch Interface 3 SIC/DSIC Slot Table 2-22 Descriptions on Rear Panel of Router 2.9.4 LED Indicator The router indicators are described in Table 2-23. Name PWR Status On Off Front Panel SYS Green Flashing rapidly Flashing slowly Description The router is powered on. The router is powered off. The router is starting. The router works properly. 30 Owner's Manual Product Controls Name Status Description Yellow Flashing rapidly The router is faulty. Off On The router does not work properly. A link is present. ETH Flashing Data is being transmitted or received. Off No link is present. Bootrom Startup Router Operation On The extended BOOTROM is present. Flashing The basic BOOTROM is present. Flashing rapidly Flashing slowly The router is operating under large traffic load. The router is operating normally. Off The router is faulty. On Off A link is present. No link is present. Flashing Data is being transmitted or received. Off No data is being transmitted or received. Table 2-23 Descriptions on Router Indicators WLAN LINK ACT Rear Panel 2.10 IP-E1 If a router is employed, no IP-EI will be required. 2.10.1 Front Panel The front panel of the IP-EI is illustrated below. 31 Product Controls Owner's Manual Figure 2-20 Front Panel of IP-E1 2.10.2 LED Indicator The IP-E1 indicators are described in Table 2-24. LED Indicator Name Status Description PWR Power Indicator On The IP-E1 is powered on. Off The IP-E1 is powered off. SYS
Reserved LNK Ethernet Indicator DUP Full Duplex/Half Duplex Indicator 100M Operating Mode and Data TX/RX Indicator 10M Operating Mode and Data TX/RX Indicator LOS1 EI Uplink Alarm Indicator On The network link is connected properly. Off The network link is disconnected. On The IP-E1 is working in full duplex mode. Off The IP-E1 is working in half duplex mode. On A 100 Mbps link is present. Flashing Data is being received or transmitted at a rate of 100Mbps. On A 10 Mbps link is present. Flashing Data is being received or transmitted at a rate of 10Mbps. On The alarm of Local E1 uplink occurs. Off No alarm exists. Table 2-24 Descriptions on IP-E1 Indicators 32 Owner's Manual 2.10.3 Rear Panel The rear panel of the IP-E1 is illustrated below. Product Controls Figure 2-21 Rear Panel of IP-E1 No. Name Description 1 2 3 4 5 6 7 8 9 AC 220V ON/OFF DC -48V AC power inlet (optional) Power switch DC power inlet (optional) 75/Up(TX) E1-75ohm unbalanced port, E1 signal output. 120/Up E1-120ohm unbalanced port, E1 signal input and output. 75/Up(RX) E1-75ohm unbalanced port, E1 signal input. 75/Down(TX) E1-75ohm unbalanced port, E1 signal output. 120/ Down E1-120ohm unbalanced port, E1 signal input and output. 75/ Down(RX) E1-75ohm unbalanced port, E1 signal input. Table 2-25 Descriptions on Rear Panel of IP-E1 2.11 Combiner (COM) The combiner is classified into broadband hybrid combiner, manual tune cavity combiner, and auto tune cavity combiner. The broadband hybrid combiner is applied to the 2-carrier base station, while the manual tune cavity combiner is applied to the base station with more than two carriers. The logical diagram of the 4-port combiner is shown in Figure 2-22. 33 Product Controls 50 Owner's Manual COM Output Cavity Resonator Cavity Resonator Cavity Resonator Cavity Resonator 50 50 50 50 CHU1 CHU2 CHU3 CHU4 Figure 2-22 Logical Diagram of 4-port Combiner Note This section takes one type of combiner as an example. 2.11.1 Function The combiner is used to integrate multiple carriers from the base station sub-system into one output port to transmit by an antenna. 2.11.2 Rear Panel The rear panel of the COM is illustrated below. Figure 2-23 Rear Panel of COM 34 Owner's Manual Product Controls No. Name Description Remarks 1 2 3 4 5 ANT COM output CH1 Carrier input 1 CH2 Carrier input 2 CH3 Carrier input 3 CH4 Carrier input 4 N-connector (female) N-connector (female) N-connector (female) N-connector (female) N-connector (female) Table 2-26 Descriptions on Rear Panel of COM 35 Installation 3. Installation 3.1 Cable Layout The cable layout of base station is shown Figure 3-1. Owner's Manual Figure 3-1 Cable Layout 3.2 Safety Information To reduce the chance of accident, please read the safety precautions very carefully before installation, maintenance and operations. 36 Owner's Manual 3.2.1 Power Supply Installation Danger:
Some components of the power system carry hazardous voltage in operation. Direct contact or indirect contact through moist objects with these components will result in fatal injury. Never wear conductive objects such as watches, bracelets, rings and etc during operation. Do use special tools in high voltage and AC operation. Do keep moisture out of the power system during operation in moist environment. The equipment should be well earthed in time to avoid damage by lightning strikes in thunderstorm. Do turn off the power before assembly or disassembly Do verify the compliance of the cable and cable label prior to connection. Ensure that the equipment is well earthed before powering on. Turn off the power immediately when water or moisture is found on the cabinet, Make sure all switches of power distribution box are set to off before installation each module in the cabinet 3.2.2 Working at Heights Warning:
Cautions shall be taken to prevent objects from falling during working at heights. Safety protection measures (e.g. wearing a hamlet or the safety belt) shall be taken. The heat-retaining clothes shall be worn before operation in cold areas. Make sure that the ladder is safe for use. Overweight on the ladder is strictly prohibited. Protective measures shall be taken if the slant of the ladder is more than 5m or the ladder is placed on a high ground (>3m) Handle and use all equipment and tools with care to avoid falling. 3.3 Installation Preparation 3.3.1 Technical Files The following table lists the files associated with hardware installation. 37 Installation Owner's Manual File type File Name Description Instructional file installation for Network Planning Drawing Site Survey Report Provided by technical sales. the R&D engineers or It is filled by the investigation engineer on site. DS-6210U5C4 PDT Trunking System Manuals DS-6210U5C4 PDT Trunking Base Station Hardware Description Manual Shipped with the equipment DS-6210U5C4 PDT Trunking Base Station Service Manual Other files Packing List Shipped with the equipment Table 3-1 Technical Files 3.3.2 Personnel Only the adequately trained personnel with satisfactory knowledge of the system can carry out the installation and tuning. The number of installation persons is subject to engineering progress and environment. 3.3.3 Tools The following tools and meter are required before installation. Claw hammer, slot type screwdriver, large Phillips screwdriver, wrench, paper knife, connector board and A type ladder. ESD-preventive wrist strap, cable peeler and crimping pliers. Multimeter Table 3-2 Tools and Meter General Tools Special Tools Meter 38 Owner's Manual 3.4 Unpacking Inspection 3.4.1 Check before Unpacking Installation After the equipment arrives at the installation site, you should:
Check against the packing list, including total amount, customer address, and etc. Contact us in case of any mistake. Check the packaging case is in good condition and not placed upside down. If the outer package is damaged seriously or soaked, please contact us immediately. Note:
To protect the equipment and investigate the cause, please properly keep the package box, equipment and packing materials, and take photo. If the above check results are good, unpack and check the equipment. 3.4.2 Unpacking Wooden Case Caution:
Keep the wooden case far away from intense shock during transportation. Never touch the parts with dirty glove during transportation. Tools Claw hammer and straight screwdriver If space permitting, carry the wooden case into or near the computer room before unpacking. This can prevent the chassis from being damaged. To unpack the wooden case, do as follows:
Step 1 Wear the ESD-preventive glove. Step 2 Lay the wooden case horizontally on the ground. Do keep the side with frame down. Step 3 Use a Claw hammer or a straight screwdriver to pry the tongue, as shown in Figure 3-2. 39 Installation Owner's Manual Figure 3-2 Removing the Cover Step 4 Remove the cover. The wooden case may contain the carton or cabinet. As for the former, directly take out the carton from the wooden case and unpack as instructed in 3.4.3Unpacking Cartons. As for the latter, proceed to the next steps. Caution Pay attention to the nails on the bottom cover, to avoid bodily injuries. Step 5 Using the same method, remove the box surrounding the plank. Step 6 Remove the foam plate. Step 7 Slide the cabinet out of the wooden case slowly. 3.4.3 Unpacking Cartons Tool Paper knife To open a carton, do as follows:
Step 1 Check the type and quantity of articles inside the carton according to labels, and cut the straps along the seam of the carton cover by the paper knife. Caution:
Use moderate force to avoid damaging the articles inside. Step 2 Remove the foam plates and articles. 40 Owner's Manual 3.4.4 Inspections Installation After unpacking all wooden cases and cartons, carefully check the name, type, quantity of goods against the Packing List, and then accept them. 3.5 Installing the Cabinet 3.5.1 Determine the Installation Position Determine the installation position of the cabinet according to the installation chart. The available space for maintenance should be preserved and be no less than 600mm around the front and back door, as shown in Figure 3-3 and Figure 3-4. Wheel Figure 3-3 Layout of holes for a Single Cabinet 41 Installation Owner's Manual Wheel Figure 3-4 Layout of holes for Combined Cabinet 3.5.2 Installing the Cabinet To install the cabinet, do as follows:
Step 1 Place the cabinet in the planned position. Fix the cabinet by tightening four bolts at the bottom of the cabinet, as shown in Figure 3-5. 1. Loosen the upper nut counter-clockwise by the spanner. 2. Loosen the lower nut counter-clockwise by the spanner and lift the cabinet to an appropriate height. 3. Tighten the upper nut and screw clockwise. Figure 3-5 Tightening the Bolt 42 Owner's Manual 3.6 Installing Modules into the Cabinet 3.6.1 Module Layout The position of all modules to be installed is shown in Figure 3-6. Installation Decorative Unit Decorative Unit Wiring Rack C H U C H U C H U C H U B S C U B S C U P S U P S U Wiring Rack FAN Wiring Rack DIU Router/IP-E1 COM c Figure 3-6 of Module Layout 3.6.2 Installation Procedures Step 1 Open the front and back door, as shown in Figure 3-7. 1. Unlock and remove the key in case of the keyhole in a horizontal position. 2. Firmly press PUSH until the door knob is bounced. 3. Turn the door knob to the right. 43 Installation 4. Pull the door knob outwards and open the cabinet door. Owner's Manual Figure 3-7 Opening the Cabinet Door Step 2 Disassemble the side doors as shown in Figure 3-9. 1. Remove the eight screws on the frame. 2. Press down on the two latches and pull out the side door outwards. Caution:
Care shall be taken to avoid injuries upon pulling out the side door outwards. Figure 3-8 Disassembling the Side Door Step 3 Insert the modules into the cartridge (take the BSCU installation for example) 44 Owner's Manual Note:
Make sure the power switch is set to OFF before installing the PSU. 1. Loosen the two ejectors as shown in Figure 3-9. Installation Figure 3-9 Loosening the Ejector 2. Slide the BSCU along the guide rails smoothly as shown in Figure 3-101. 3. Perform the step 1 in a reverse way to lock the two ejectors. 4. Tighten the two screws on the two ejectors and the board respectively as shown in Figure 3-102. Note:
Loosen the two ejectors and draw out the module in case of removing it during installation. Figure 3-10 Installing the BSCU Step 4 Install the FAN as shown in Figure 3-11. 45 Installation Owner's Manual 1. Slide the FAN along the guide rails smoothly until a click is heard. 2. Fasten the two screws on the ear of the FAN. Figure 3-11 Installing the FAN Figure 3-12 Removing the FAN Note:
During installation, if you have to take out the FAN, please first unfasten the screws, and then unlock the first panel, finally pull the FAN out. See Figure 3-12. Step 5 Install the DIU as shown in Figure 3-13. 1. Slide the DIU along the guide rails. 2. Fasten all screws to fix the DIU. Figure 3-13 Installing the Divider Unit Step 6 Install the COM as shown in Figure 3-14. 1. Slide the COM along the guide rails. 2. Fasten the four screws. 46 Owner's Manual Caution:
Handle with care as the COM is heavy. Installation Figure 3-14 Installing the Combiner Unit Step 7 Connect all cables as shown in Figure 3-16. Figure 3-15 Cable Diagram Step 8 Install the side doors. 1. Align the side door with the frame and firmly press the latch. 2. Fasten the eight screws. 3.7 Installing Cables 3.7.1 Equipment Status The equipment shall be in the following status before connecting cables:
The cabinet has been installed. All modules have been installed and the power switch is set to OFF. 3.7.2 Cables Cables are described in Table 3-3 and their positions are shown in Figure 3-16. Installation positions 47 Installation are located on top of the cabinet. Owner's Manual Name Color Remark Base Station Ground Cable (40m) Yellowish green AC Power Cord (15m) Black/white Lead, 16 mm2, 49-core, and 450/750V, outer diameter:
8.1 Subject to the actual needs. 3-core, 300/500V, 3*2.5 mm2, Subject investigating data on the site to the RF Jumpers (3 pcs) Black 1/2 inch, N-Male to N-Male, 3Pcs Table 3-3 Cables Description Figure 3-16 External Cable Connection No. 1 3 5 Name GPS Antenna Interface TX Interface Ground Interface No. 2 4 6 Name RX Interface Communication Interface Power Inlet Table 3-4 Descriptions on the interface of external cable connection Note:
Install the power cable properly. Do handle the ground cable gently to avoid possible looseness during installation. 48 Owner's Manual Installation The Disconnector is available for shortcut between the live line and null line only. 3.8 Examination after Installation 3.8.1 Equipment Status The equipment shall be in the following status prior to hardware examination. The cabinet has been installed. All modules have been installed. The external power has been installed and all cables have been connected. All switches of the power distribution box are set to OFF. 3.8.2 Examining the Cabinet The following requirements shall be met after installation. No. Check Item 1 2 3 4 5 6 7 8 9 The position of the cabinet should conform to the design drawing. All modules should be installed correctly. All cables within the cabinet should be connected properly. The side door should be installed and the grounding cables should be connected properly. All screws should be tightened. Be sure to put flat washers and spring washers on all bolts correctly. The cabinet should be placed horizontally and orderly. The surface of the cabinet should be clean and well painted. No dust and other sundries are in the cabinet. All labels should be correct, clear and not be missed. The plastic dust cap on top of the cabinet should be installed properly. Table 3-5 Checklist of Cabinet Installation 3.8.3 Examining Cables The following requirements should be met after connection. 49 Installation No. Owner's Manual Check Item 1 2 3 All cables should not be damaged. All cables are one-piece cables, without any joint in the middle. Excess grounding cables should be cut off. Table 3-6 Checklist of Cables 3.8.4 Power On and Examination Caution:
First measure the resistance of all power connectors and ground connectors using the multimeter and check whether short circuit occurs. The procedures are described as follows:
Step 1 Check the input voltage (220V) from the main power and whether the live line and null line connect correctly. Step 2 The switch of the Disconnector in the BSIU is set to ON. Step 3 All switches of the PSU are set to ON. Step 4 Check whether all modules are powered properly. Name Normal Power Indication CHU The PWR indicator on the front panel glows and the ALM indicator goes out. BSCU The PWR indicator on the front panel glows and the ALM indicator goes out. PSU FAN The PWR indicator on the front panel glows and the ALM indicator goes out. The PWR indicator on the front panel glows. Table 3-7 Checklist of Power Situation Note:
If the LED on the front panel does not work correctly, please re-power it on or re-insert the module after disconnecting power. If it doesnt solve the problem, please contact us. 3.8.5 Environment Examination The following table lists the check item of environment on site. 50 Owner's Manual No. Check Item Installation 1 2 3 The equipment room should be clean and tidy. No sundries should be placed in the grooves, at the bottom of the cabinet or around the cabinet. The floor in the equipment room should be free from sundries. Table 3-8 Checklist of Environment on Site 51 Owner's Manual Basic Operations 4. Basic Operations 4.1 Powering on Step 1 The external power supply is connected. Step 2 The switch of the Disconnector is set to ON. Step 3 All switches of the PSU are set to ON. 4.2 Powering off Step 1 All switches of the PSU are set to OFF. Step 2 The switch of the Disconnector is set to OFF. Step 3 Disconnect the external power supply. 52 Owner's Manual 5. Troubleshooting Troubleshooting Phenomena Solution The PWR LED does not light up. Check the power supply. The ALM LED on the PSU glows red. Disconnect the power and replace the PSU. The ALM LED on the CHU glows red. Replace the CHU. The ALM LED on the BSCU glows red. Replace the BSCU. Table 5-1 Troubleshooting 53 Routine Maintenance Owner's Manual 6. Routine Maintenance 6.1 Purpose Routine maintenance is to ensure stable and reliable operation of the equipment. It can help to know the operation status of the equipment, so as to detect the potential troubles and remove them on time. The routine maintenance should achieve the following objects:
Remove all potential troubles to keep the system work properly. Ensure all performance and service specifications meet requirements. Ensure good collaboration with the entire network. Make sure that new equipment or the extended equipment accesses to the network properly. 6.2 Tasks Clean the equipment room regularly. Check the working status of the base station regularly. If the abnormal situation occurs, deal with it in time. Clean up the dust regularly. 54 Owner's Manual Routine Maintenance A Abbreviations Abbr. AGC BSCU Auto Gain Control Base Station Controller Unit Full Name BSCU-MB Base Station Controller Unit Main Board Base Station Sub-system Controller Area Network Call Control Call Control Layer Channel Board Channel Unit Combiner Compact Peripheral Component Interconnect Divider Unit Data Link Layer Extended Chassis Extended Interface Board European Telecommunications Standards Institute Fan Unit General Purpose Input General Purpose Input Output General Purpose Output Global Positioning System GPS Clock Board BSS CAN CC CCL CHB CHU COM CPCI DIU DLL EC EIB ETSI FAN GPI GPIO GPO GPS GPSB 55 Routine Maintenance Abbr. Owner's Manual Full Name Interconnect Backboard Input and Output Interconnect Relay Unit Logical Link Control Low Noise Amplifier Media Access Control Main Chassis Main Control Board Mobile Management Machine-Frame Power Support Component Micro Processor Unit Power Amplifier Board Peripheral Component Interconnect PCI Industrial Computer Manufacture's Group Professional Digital Trunking Package Switch Board Power Support Unit Radio Frequency Distributing System Router Receive Board Time Division Multiplex Tower Mounted Amplifier Trunking Station Control Unit Excitation Board ICB IO IRU LLC LNA MAC MC MCB MM MPSC MPU PAB PCI PICMG PDT PSB PSU RFDS RT RXB TDM TMA TSCU EXB 56 Owner's Manual Abbr. VGA Video Graphics Array Routine Maintenance Full Name 57 Owner's Manual FCC Warning Routine Maintenance Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation environment .This equipment should be installed and operated with minimum distance 2.5 m between the radiator& your body. exposure limits set forth for an controlled Industry Canada This device complies with Industry Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. The term IC: before the certification/registration number only signifies that the Industry Canada technical specifications were met. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that, the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. 58 Owner's Manual Routine Maintenance This product meets the applicable Industry Canada technical specifications. Le present matriel est conforme aux specifications techniques applicables dIndustrie Canada. This Class A digital apparatus complies with Canadian ICES-003. IC Radiation Exposure Statement:
This equipment complies with IC RF radiation exposure limits set forth for an controlled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 2.5m between the radiator & your body. 59
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2014-02-27 | 935 ~ 940 | TNB - Licensed Non-Broadcast Station Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2014-02-27
|
||||
1 | Applicant's complete, legal business name |
Hytera Communications Corporation Limited
|
||||
1 | FCC Registration Number (FRN) |
0019701887
|
||||
1 | Physical Address |
Hytera Tower, Hi-Tech Industrial Park North
|
||||
1 |
Shenzhen, N/A 518057
|
|||||
1 |
China
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
b******@baclcorp.com
|
||||
1 | TCB Scope |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
YAM
|
||||
1 | Equipment Product Code |
DS-6210U5C4
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
T****** C******
|
||||
1 | Title |
Certification Engineer
|
||||
1 | Telephone Number |
+86-7********
|
||||
1 | Fax Number |
+86-7********
|
||||
1 |
t******@hytera.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | TNB - Licensed Non-Broadcast Station Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | DMR Trunking Base Station | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power listed is conducted at antenna terminal. The antenna(s) used for this transmitter must be fixed-mounted on outdoor permanent structures. RF exposure compliance is addressed at the time of licensing, as required by the responsible FCC Bureau(s), including antenna co-location requirements of §1.1307(b)(3). | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Bay Area Compliance Laboratories Corp. (Dongguan)
|
||||
1 | Name |
J******** C********
|
||||
1 | Telephone Number |
86-76******** Extension:
|
||||
1 |
j******@baclcorp.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 9 | BC | 851 | 869 | 35.24 | 0.1 ppm | 7K40FXW | |||||||||||||||||||||||||||||||||
1 | 2 | 9 | BC | 935 | 940 | 29.58 | 0.1 ppm | 7K40FXW |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC