1. Product Overview 2. Before Use 2.1 Installing the Nano SIM Card 1. Remove the battery cover with a proper tool. The battery cover is tightly fastened to ensure optimum waterproof performance. Therefore, you need to remove the battery cover with a proper tool. Do not remove the battery cover by force. 2. Open the SIM card slot cover. 3. Install the SIM card. 4. Put the card slot cover back in place. 2.2 Attaching the Battery Use the approved battery to avoid the risk of explosion. Dispose of the used battery according to "Precautions for Disposal" in the Safety Information Booklet. Attach the battery as shown below, and then attach the battery cover back. 2.3 Attaching the Belt Clip 2.4 Attaching the Audio Accessory Open the audio jack cover, and then insert the audio accessory into the jack. To ensure optimum waterproof and dustproof performance, close the audio jack cover after disconnecting the audio accessory. 2.5 Charging the Battery Use the approved charger to charge the battery. Read the Safety Information Booklet before charging. The remaining lithium-ion battery power is limited to 30% pursuant to the new lithium battery shipment regulation approved by the International Air Transport Association (IATA). Before initial use, charge the battery. To charge the battery, connect the product to a power adapter, power bank, or computer with the USB cable. To determine the charging status, check the battery icon shown on the LCD display. To ensure optimum waterproof and dustproof performance, close the USB Type-C port cover after charging the product. 3. Basic Operations 3.1 Turning on/off the Product To turn on the product, long press for two seconds. 3.2 Adjusting the Volume To increase the volume, press the Volume + key. To decrease the volume, press the Volume key. To turn off the product, long press for two seconds, and then select Power off. 3.3 Locking/Unlocking the Screen 1. To lock the screen, go to Settings > Screen locked to enable the feature. If the product is not operated for a specific duration, the screen will be automatically locked. 2. To unlock the screen, press and
. 3.4 Connecting to the Network To connect to the cellular network, install the Nano SIM card and activate the cellular data service. 3.5 Checking the Device Information To check the information such as model, serial number, and version, go to Settings > About phone. You can use Push-to-Talk over Cellular (PoC) services such as one-to-one or one-to-many voice call over the 4. PoC Services public network. To initiate a call, do as follows. a. Select a contact. b. Press and hold the PTT key, and then speak. c. Release the PTT key. You can receive a call without any operation. 5. Specifications Specifications Model PNC360S FDD-LTE:
B2/B4/B5/B7/B12/B13/B17/B26/B38/B41 TDD-LTE:
B38/B41 WCDMA:
B2/B4/B5 TD-SCDMA: B34/B39 GSM:
850/1900 BT:
BT4.1 WIFI:802.11b/g/n ht20/n ht40 GPS:
GPS/Beidou/Glonass/Galileo/AGPS
-20C to +60C 10C to +45C V1.0.01.000.02 V1.00 Adaptor, Belt Clip, Battery Frequen cy Range Operatio nal Temper ature Battery Chargin g Temper ature Softwar e Version Hardwar e Version Accesso ries Specifications S010WV0500200 100-240V~50/60Hz 0.4A 5.0V/2.0A Tradem ark Adapter Model Adapter Input Adapter Output Battery Caution CAUTION Risk of explosion if the battery is replaced by an incorrect type disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can re sult in an explosion;
leaving a battery in an extremely high temperature surrounding environment that can result in an explo sion or the leakage of flammable liquid or gas;
a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flam mable liquid o gas This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cau undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device has been tested and complies with SAR limits, users can obtain Canadian information on RF exposure and compliance Aprs examen de ce matriel aux conformit aux limites DAS, et/ou aux limites dintensit de champ RF, les utilisateurs peuvent sur lexposition aux radiofrquences et la conformit and compliance dacqurir les informations correspondantes. SAR tests are conducted using standard operating positions accepted by the FCC/ISEDC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. Before a new model device is a available for sale to the public, it must be tested and certified to the FCC/
ISEDC that it does not exceed the exposure limit established by the FCC/ISEDC, Tests for each device are performed in positions and locations (worn on the body)as required by the FCC/ISEDC. For face-up, mm was used for test, this equipment should be installed and operated with minimum distance 25 For body worn operation, this device has been tested and meets the FCC/ISEDC RF exposure guidelines when used with an accessory designated for this product or when used with an accessory that contains no metal and that positions the handset a minimum of 10mm from the body. mm. 25 Non-compliance with the above restrictions may result in violation of RF exposure guidelines. Les essais SAR sont effectus laide de positions dexploitation normalises acceptes par la FCC/ISEDC avec lappareil transmettant son niveau de puissance certifi le plus lev dans toutes les bandes de frquences testes, bien que le SAR soit dtermin au niveau de puissance certifi le plus lev, le niveau rel de R-S de lappareil pendant son fonctionnement peut tre bien infrieur la valeur maximale. Avant quun nouveau dispositif de modle ne soit disponible la vente au public, il doit tre test et certifi la FCC/ISEDC quil ne dpasse pas la limite dexposition tablie par la FCC/ISEDC, les tests pour chaque appareil sont effectus dans des positions et des emplacements (ports sur le corps) comme lexige la FCC/
ISEDC. Pour le face-vers le haut, avec une distance minimale de mm. 25 Pour un fonctionnement port sur le corps, cet appareil a t test et rpond aux directives d'exposition RF FCC/ISEDC avec un accessoire conu pour ce produit ou lorsqu'il est utilis avec un accessoire qui ne contient pas lorsqu'il est utilis de mtal et qui mm a t utilis pour lessai, cet quipement doit tre install et actionn positionne le combin au moins 10 mm du corps. 25 Le non-respect des restrictions ci-dessus peut entraner une violation des lignes directrices sur lexposition aux RF. This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,in cluding interference that may cause undesired operation of the device. Le onjunc areil est conforme aux CNR d linnovation, la science et le dveloppement conomique Canada licables aux areils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
(1) lareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accept er tout brouillage radiolectrique subi,
onj si le brouillage est susceptible den compromettre le fonctionnement.