all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Quick Guide | Users Manual | 305.74 KiB | ||||
1 | Test Report | |||||||
1 | Cover Letter(s) | |||||||
1 | Block Diagram | |||||||
1 | Cover Letter(s) | |||||||
1 | Operational Description | |||||||
1 | Test Report | |||||||
1 | External Photos | |||||||
1 | Test Report | |||||||
1 | Test Report | |||||||
1 | Internal Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | Block Diagram | |||||||
1 | RF Exposure Info | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | Quick Guide | Users Manual | 305.74 KiB |
BLUETOOTH PRINTER ADAPTER Blue light Lorem ipsum Lorem ipsum Lorem ipsum Lorem ipsum Parallel port Lorem ipsum Lorem ipsum Lorem ipsum Lorem ipsum Test button Power outled Lorem ipsum Lorem ipsum Lorem ipsum Lorem ipsum Lorem ipsum Lorem ipsum Lorem ipsum Lorem ipsum Yellow light Lorem ipsum Lorem ipsum Lorem ipsum Lorem ipsum BLUETOOTH PRINTER ADAPTER MPI Tech Corporate Headquarters Vadstrupvej 35-43 DK-2880 Bagsvrd Denmark Phone: +45 4436 6000 Fax: +45 4436 6111 E-mail: sales-ne@i-data.com Web: www.mpitech.com Quick Guide English 2-3 Deutsch 4-5 Francais 5-6 Italiano 6-7 Espanol 8-9 MPI Tech is a business unit of i-data international a-s Wireless Printing Solutions A. Connect hardware 1 Off 2 3 On 4 20s 5 B. Light indicators C. Additional print of test page A. CONNECT HARDWARE Follow the steps below to connect the hardware:
1. Power off the printer. 2. Connect the Bluetooth Printer Adapter to the parallel port of the printer and secure it using the two mounting clips. 3. Power on the printer. 4. Connect the included power adapter to the Bluetooth Printer Adapter and to the power outlet. Turn on the power. 5.The test page is printed after approx. 20 seconds. The Bluetooth Printer Adapter can now be used for Bluetooth printing. B. LIGHT INDICATORS At power on the blue light is on for approx. 20 seconds, where after it starts to flash (indicating it is ready). The blue light is on whenever a connection has been established to another Bluetooth device. The yellow light indicates that data is available. C. ADDITIONAL PRINT OF TEST PAGE Press the Bluetooth Printer Adapters TEST button to print the test page. The test page contains information about the Product Version (500.xxx) and the Bluetooth Device Address
(00:03:6E:XX:XX:XX). Congratulations with your Bluetooth Printer Adapter from MPI Tech, a business unit of i-data international a-s. This docu-
ment will assist you in getting started with Bluetooth printing. A printer with parallel port (IEEE 1284-B). Please order converter cable (MPI Tech p/n 999034-030) if your printer is equipped with a small parallel port connector (IEEE 1284-C). BLUETOOTH PRINTING Please refer to the documentation that came with your Bluetooth device, e.g. laptop, PDA or mobile phone. At our web site you will find instructions for Bluetooth Printing. Please refer to www.mpitech.com/btpa INTRODUCTION The Bluetooth Printer Adapter replaces the parallel cable of the printer and enables printing from Bluetooth enabled devices such as laptops, PDAs and mobile phones. ITEMS SUPPLIED The Bluetooth Printer Adapter Kit contains:
Bluetooth Printer Adapter Power adapter Quick Guide (this document) PREREQUISITES At our web site www.mpitech.com/btpa you will find an updated list of supported Bluetooth devices and printers. In general the following is required:
A Bluetooth enabled device in the form of a laptop, PDA or mobile phone. The Bluetooth device must support at least one of the following Bluetooth profiles to print:
SPP Serial Port Profile. OPP Object Push Profile
(vCard and vCalendar). HCRP Hardcopy Cable Replacement Profile. REGULATORY INFORMATION This product complies with any mandatory product specification in any country where the product is sold. In addition, the product complies with the following directives:
SAFETY REGULATIONS NOTE: Only use this product with a Class 2 Direct Plug-In Transformer rated 5.0-> 5.5 Vdc minimun 0.40 A United States of America and Canada The equipment is tested to comply with UL1950 3rd edi-
tion and marked in accordance with UL and cUL marks. European Union The product is tested to comply with the Low voltage Directive 73/23/EEC according to EN60950 with amend-
ments. ELECTRONIC EMISSION NOTICES Federal Communications Commission (FCC) Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio fre-
quency, energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
E N G L I S H European Union EMC Directive conformance statement This product is in conformity with the protection requirements of EU Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. MPI Tech cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product. This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to CISPR 22/European Standard EN 55022. The limits for Class B equipment were derived for typical residential environments to provide reasonable protection against interference with licensed communication devices. RADIO EQUIPMENT REGULATIONS European Union This equipment complies with the R&TTE directive 1999/5/EC and has been pro-vided with the CE mark accordingly. Note that the radio frequency band used by this equipment has not been harmonized in all of the EU. United States of America and Canada Tested to comply with FCC Standards FOR HOME OR OFFICE USE. See FCC 47CFR part 15.19(b)(2). This device complies with part 15 of the FCC rules and with RSS-210 / RSS-139 of the Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired opera-
tion. CAUTION: Any changes or modifications to this equip-
ment not expressly approved by the manufacturer may void the FCC authorization to operate this equipment. Canada (IC notice) To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment that is installed outdoors is subject to licensing. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult an MPI Tech authorized dealer or service repre-
sentative for help. Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Proper cables and connectors are available from MPI Tech authorized dealers. MPI Tech is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equip-
ment. Unauthorized changes or modifications could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Industry Canada Class B emission compliance statement This Class B digital apparatus complies with Canadian ICES-003. A. CONNECT HARDWARE Follow the steps below to connect the hardware:
Congratulations with your Bluetooth Printer Adapter from MPI Tech, a business unit of i-data international a-s. This document will assist you in getting started with Bluetooth printing. 1. Power off the printer. 2. Connect the Bluetooth Printer Adapter to the parallel port of the printer and secure it using the two mounting clips. 3. Power on the printer. 4. Connect the included power adapter to the Bluetooth Printer Adapter and to the power outlet. Turn on the power. 5.The test page is printed after approx. 20 seconds. The Bluetooth Printer Adapter can now be used for Bluetooth printing. B. LIGHT INDICATORS At power on the blue light is on for approx. 20 seconds, where after it starts to flash (indicating it is ready). The blue light is on whenever a connection has been established to another Bluetooth device. The yellow light indicates that data is available. C. ADDITIONAL PRINT OF TEST PAGE Press the Bluetooth Printer Adapters TEST button to print the test page. The test page contains information about the Product Version (500.xxx) and the Bluetooth Device Address
(00:03:6E:XX:XX:XX). INTRODUCTION The Bluetooth Printer Adapter replaces the par-
allel cable of the printer and enables printing from Bluetooth enabled devices such as lap-
tops, PDAs and mobile phones. Items Supplied The Bluetooth Printer Adapter Kit contains:
Bluetooth Printer Adapter Power adapter Quick Guide (this document) PREREQUISITES At our web site www.mpitech.com/btpa you will find an updated list of supported Bluetooth devices and printers. In general the following is required:
A Bluetooth enabled device in the form of a laptop, PDA or mobile phone. The Bluetooth device must support at least one of the follow-
ing Bluetooth profiles to print:
SPP Serial Port Profile. OPP Object Push Profile (vCard and vCalendar). HCRP Hardcopy Cable Replacement Profile. A PCL 3 or higher enabled printer with parallel port (IEEE 1284-B). Please order converter cable (MPI Tech p/n 999034-030) if your printer is equipped with a small parallel port connector (IEEE 1284-C). BLUETOOTH PRINTING Please refer to the documentation that came with your Bluetooth device, e.g. laptop, PDA or mobile phone. At our web site you will find instructions for Bluetooth Printing. Please refer to www.mpitech.com/btpa A - CONNECT HARDWARE Follow the steps below to connect the hard-
ware:
Power off your printer. Connect the Bluetooth Printer Adapter to the parallel port of the printer and secure it using the two mounting clips. Connect the included power adapter to the Bluetooth Printer Adapter and to the power out-
let. Power on the printer. The test page is printed after approx. 20 sec-
onds. The Bluetooth Printer Adapter can now be used for Bluetooth printing. B - LIGHT INDICATORS At power on the blue light is on for approx. 20 seconds, where after it starts to flash (indicat-
ing it is ready). The blue light is on whenever a connection has been established to another Bluetooth device. The yellow light indicates that data is available. C - ADDITIONAL PRINT OF TEST PAGE Press the Bluetooth Printer Adapters TEST but-
ton to print the test page. The test page con-
tains information about the Product Version
(500.xxx) and the Bluetooth Device Address
(00:03:6E:XX:XX:XX). REGULATORY INFORMATION This product complies with any mandatory product specification in any country where the product is sold. In addition, the product complies with the following directives:
SAFETY REGULATIONS NOTE: Only use this product with a Class 2 Direct Plug-
In Transformer rated 5.0-> 5.5 Vdc minimun 0.40 A United States of America and Canada The equipment is tested to comply with UL1950 3rd edition and marked in accordance with UL and cUL marks. European Union The product is tested to comply with the Low voltage Directive 73/23/EEC according to EN60950 with amend-
ments. RADIO EQUIPMENT REGULATIONS European Union This equipment complies with the R&TTE directive 1999/5/EC and has been pro-vided with the CE mark accordingly. Note that the radio frequency band used by this equipment has not been harmonized in all of the EU. United States of America and Canada Tested to comply with FCC Standards FOR HOME OR OFFICE USE. See FCC 47CFR part 15.19(b)(2). This device complies with part 15 of the FCC rules and with RSS-210 / RSS-139 of the Industry Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause unde-
sired operation. CAUTION: Any changes or modifications to this equip-
ment not expressly approved by the manufacturer may void the FCC authorization to operate this equipment. Canada (IC notice) To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment that is installed outdoors is subject to licensing. ELECTRONIC EMISSION NOTICES Federal Communications Commission (FCC) Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio fre-
quency, energy and, if not installed and used in accor-
dance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected. Consult an MPI Tech authorized dealer or service rep-
resentative for help. Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Proper cables and connectors are available from MPI Tech authorized dealers. MPI Tech is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equip-
ment. Unauthorized changes or modifications could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired oper-
ation. Industry Canada Class B emission compliance state-
ment This Class B digital apparatus complies with Canadian ICES-003. European Union EMC Directive conformance state-
ment This product is in conformity with the protection requirements of EU Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. MPI Tech can-
not accept responsibility for any failure to satisfy the protection requirements resulting from a non-recom-
mended modification of the product. This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to CISPR 22/European Standard EN 55022. The limits for Class B equipment were derived for typical residential environments to provide reasonable protection against interference with licensed communication devices. D E U T S C H A. CONNECT HARDWARE Follow the steps below to connect the hardware:
Congratulations with your Bluetooth Printer Adapter from MPI Tech, a business unit of i-data international a-s. This document will assist you in getting started with Bluetooth printing. 1. Power off the printer. 2. Connect the Bluetooth Printer Adapter to the parallel port of the printer and secure it using the two mounting clips. 3. Power on the printer. 4. Connect the included power adapter to the Bluetooth Printer Adapter and to the power outlet. Turn on the power. 5.The test page is printed after approx. 20 seconds. The Bluetooth Printer Adapter can now be used for Bluetooth printing. B. LIGHT INDICATORS At power on the blue light is on for approx. 20 seconds, where after it starts to flash (indicating it is ready). The blue light is on whenever a connection has been established to another Bluetooth device. The yellow light indicates that data is available. C. ADDITIONAL PRINT OF TEST PAGE Press the Bluetooth Printer Adapters TEST button to print the test page. The test page contains information about the Product Version (500.xxx) and the Bluetooth Device Address
(00:03:6E:XX:XX:XX). INTRODUCTION The Bluetooth Printer Adapter replaces the par-
allel cable of the printer and enables printing from Bluetooth enabled devices such as lap-
tops, PDAs and mobile phones. Items Supplied The Bluetooth Printer Adapter Kit contains:
Bluetooth Printer Adapter Power adapter Quick Guide (this document) PREREQUISITES At our web site www.mpitech.com/btpa you will find an updated list of supported Bluetooth devices and printers. In general the following is required:
A Bluetooth enabled device in the form of a laptop, PDA or mobile phone. The Bluetooth device must support at least one of the follow-
ing Bluetooth profiles to print:
SPP Serial Port Profile. OPP Object Push Profile (vCard and vCalendar). HCRP Hardcopy Cable Replacement Profile. A PCL 3 or higher enabled printer with parallel port (IEEE 1284-B). Please order converter cable (MPI Tech p/n 999034-030) if your printer is equipped with a small parallel port connector (IEEE 1284-C). BLUETOOTH PRINTING Please refer to the documentation that came with your Bluetooth device, e.g. laptop, PDA or mobile phone. At our web site you will find instructions for Bluetooth Printing. Please refer to www.mpitech.com/btpa A - CONNECT HARDWARE Follow the steps below to connect the hard-
ware:
Power off your printer. Connect the Bluetooth Printer Adapter to the parallel port of the printer and secure it using the two mounting clips. Connect the included power adapter to the Bluetooth Printer Adapter and to the power out-
let. Power on the printer. The test page is printed after approx. 20 sec-
onds. The Bluetooth Printer Adapter can now be used for Bluetooth printing. B - LIGHT INDICATORS At power on the blue light is on for approx. 20 seconds, where after it starts to flash (indicat-
ing it is ready). The blue light is on whenever a connection has been established to another Bluetooth device. The yellow light indicates that data is available. C - ADDITIONAL PRINT OF TEST PAGE Press the Bluetooth Printer Adapters TEST but-
ton to print the test page. The test page con-
tains information about the Product Version
(500.xxx) and the Bluetooth Device Address
(00:03:6E:XX:XX:XX). REGULATORY INFORMATION This product complies with any mandatory product specification in any country where the product is sold. In addition, the product complies with the following directives:
SAFETY REGULATIONS NOTE: Only use this product with a Class 2 Direct Plug-
In Transformer rated 5.0-> 5.5 Vdc minimun 0.40 A United States of America and Canada The equipment is tested to comply with UL1950 3rd edition and marked in accordance with UL and cUL marks. European Union The product is tested to comply with the Low voltage Directive 73/23/EEC according to EN60950 with amend-
ments. RADIO EQUIPMENT REGULATIONS European Union This equipment complies with the R&TTE directive 1999/5/EC and has been pro-vided with the CE mark accordingly. Note that the radio frequency band used by this equipment has not been harmonized in all of the EU. United States of America and Canada Tested to comply with FCC Standards FOR HOME OR OFFICE USE. See FCC 47CFR part 15.19(b)(2). This device complies with part 15 of the FCC rules and with RSS-210 / RSS-139 of the Industry Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause unde-
sired operation. CAUTION: Any changes or modifications to this equip-
ment not expressly approved by the manufacturer may void the FCC authorization to operate this equipment. Canada (IC notice) To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment that is installed outdoors is subject to licensing. ELECTRONIC EMISSION NOTICES Federal Communications Commission (FCC) Statement Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio fre-
quency, energy and, if not installed and used in accor-
dance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected. Consult an MPI Tech authorized dealer or service rep-
resentative for help. Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Proper cables and connectors are available from MPI Tech authorized dealers. MPI Tech is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equip-
ment. Unauthorized changes or modifications could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired oper-
ation. Industry Canada Class B emission compliance state-
ment This Class B digital apparatus complies with Canadian ICES-003. European Union EMC Directive conformance state-
ment This product is in conformity with the protection requirements of EU Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. MPI Tech can-
not accept responsibility for any failure to satisfy the protection requirements resulting from a non-recom-
mended modification of the product. This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to CISPR 22/European Standard EN 55022. The limits for Class B equipment were derived for typical residential environments to provide reasonable protection against interference with licensed communication devices. F R E N C H A. CONNECT HARDWARE Follow the steps below to connect the hardware:
Congratulations with your Bluetooth Printer Adapter from MPI Tech, a business unit of i-data international a-s. This document will assist you in getting started with Bluetooth printing. 1. Power off the printer. 2. Connect the Bluetooth Printer Adapter to the parallel port of the printer and secure it using the two mounting clips. 3. Power on the printer. 4. Connect the included power adapter to the Bluetooth Printer Adapter and to the power outlet. Turn on the power. 5.The test page is printed after approx. 20 seconds. The Bluetooth Printer Adapter can now be used for Bluetooth printing. B. LIGHT INDICATORS At power on the blue light is on for approx. 20 seconds, where after it starts to flash (indicating it is ready). The blue light is on whenever a connection has been established to another Bluetooth device. The yellow light indicates that data is available. C. ADDITIONAL PRINT OF TEST PAGE Press the Bluetooth Printer Adapters TEST button to print the test page. The test page contains information about the Product Version (500.xxx) and the Bluetooth Device Address
(00:03:6E:XX:XX:XX). INTRODUCTION The Bluetooth Printer Adapter replaces the par-
allel cable of the printer and enables printing from Bluetooth enabled devices such as lap-
tops, PDAs and mobile phones. Items Supplied The Bluetooth Printer Adapter Kit contains:
Bluetooth Printer Adapter Power adapter Quick Guide (this document) PREREQUISITES At our web site www.mpitech.com/btpa you will find an updated list of supported Bluetooth devices and printers. In general the following is required:
A Bluetooth enabled device in the form of a laptop, PDA or mobile phone. The Bluetooth device must support at least one of the follow-
ing Bluetooth profiles to print:
SPP Serial Port Profile. OPP Object Push Profile (vCard and vCalendar). HCRP Hardcopy Cable Replacement Profile. A PCL 3 or higher enabled printer with parallel port (IEEE 1284-B). Please order converter cable (MPI Tech p/n 999034-030) if your printer is equipped with a small parallel port connector (IEEE 1284-C). BLUETOOTH PRINTING Please refer to the documentation that came with your Bluetooth device, e.g. laptop, PDA or mobile phone. At our web site you will find instructions for Bluetooth Printing. Please refer to www.mpitech.com/btpa A - CONNECT HARDWARE Follow the steps below to connect the hard-
ware:
Power off your printer. Connect the Bluetooth Printer Adapter to the parallel port of the printer and secure it using the two mounting clips. Connect the included power adapter to the Bluetooth Printer Adapter and to the power out-
let. Power on the printer. The test page is printed after approx. 20 sec-
onds. The Bluetooth Printer Adapter can now be used for Bluetooth printing. B - LIGHT INDICATORS At power on the blue light is on for approx. 20 seconds, where after it starts to flash (indicat-
ing it is ready). The blue light is on whenever a connection has been established to another Bluetooth device. The yellow light indicates that data is available. C - ADDITIONAL PRINT OF TEST PAGE Press the Bluetooth Printer Adapters TEST but-
ton to print the test page. The test page con-
tains information about the Product Version
(500.xxx) and the Bluetooth Device Address
(00:03:6E:XX:XX:XX). REGULATORY INFORMATION This product complies with any mandatory product specification in any country where the product is sold. In addition, the product complies with the following directives:
SAFETY REGULATIONS NOTE: Only use this product with a Class 2 Direct Plug-
In Transformer rated 5.0-> 5.5 Vdc minimun 0.40 A United States of America and Canada The equipment is tested to comply with UL1950 3rd edition and marked in accordance with UL and cUL marks. European Union The product is tested to comply with the Low voltage Directive 73/23/EEC according to EN60950 with amend-
ments. RADIO EQUIPMENT REGULATIONS European Union This equipment complies with the R&TTE directive 1999/5/EC and has been pro-vided with the CE mark accordingly. Note that the radio frequency band used by this equipment has not been harmonized in all of the EU. United States of America and Canada Tested to comply with FCC Standards FOR HOME OR OFFICE USE. See FCC 47CFR part 15.19(b)(2). This device complies with part 15 of the FCC rules and with RSS-210 / RSS-139 of the Industry Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause unde-
sired operation. CAUTION: Any changes or modifications to this equip-
ment not expressly approved by the manufacturer may void the FCC authorization to operate this equipment. Canada (IC notice) To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment that is installed outdoors is subject to licensing. ELECTRONIC EMISSION NOTICES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired oper-
ation. Industry Canada Class B emission compliance state-
ment Federal Communications Commission (FCC) Statement This Class B digital apparatus complies with Canadian ICES-003. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio fre-
quency, energy and, if not installed and used in accor-
dance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected. Consult an MPI Tech authorized dealer or service rep-
resentative for help. Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Proper cables and connectors are available from MPI Tech authorized dealers. MPI Tech is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equip-
ment. Unauthorized changes or modifications could void the users authority to operate the equipment. European Union EMC Directive conformance state-
ment This product is in conformity with the protection requirements of EU Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. MPI Tech can-
not accept responsibility for any failure to satisfy the protection requirements resulting from a non-recom-
mended modification of the product. This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to CISPR 22/European Standard EN 55022. The limits for Class B equipment were derived for typical residential environments to provide reasonable protection against interference with licensed communication devices. I T A L I A N O A. CONNECT HARDWARE Follow the steps below to connect the hardware:
Congratulations with your Bluetooth Printer Adapter from MPI Tech, a business unit of i-data international a-s. This document will assist you in getting started with Bluetooth printing. 1. Power off the printer. 2. Connect the Bluetooth Printer Adapter to the parallel port of the printer and secure it using the two mounting clips. 3. Power on the printer. 4. Connect the included power adapter to the Bluetooth Printer Adapter and to the power outlet. Turn on the power. 5.The test page is printed after approx. 20 seconds. The Bluetooth Printer Adapter can now be used for Bluetooth printing. B. LIGHT INDICATORS At power on the blue light is on for approx. 20 seconds, where after it starts to flash (indicating it is ready). The blue light is on whenever a connection has been established to another Bluetooth device. The yellow light indicates that data is available. C. ADDITIONAL PRINT OF TEST PAGE Press the Bluetooth Printer Adapters TEST button to print the test page. The test page contains information about the Product Version (500.xxx) and the Bluetooth Device Address
(00:03:6E:XX:XX:XX). INTRODUCTION The Bluetooth Printer Adapter replaces the par-
allel cable of the printer and enables printing from Bluetooth enabled devices such as lap-
tops, PDAs and mobile phones. Items Supplied The Bluetooth Printer Adapter Kit contains:
Bluetooth Printer Adapter Power adapter Quick Guide (this document) PREREQUISITES At our web site www.mpitech.com/btpa you will find an updated list of supported Bluetooth devices and printers. In general the following is required:
A Bluetooth enabled device in the form of a laptop, PDA or mobile phone. The Bluetooth device must support at least one of the follow-
ing Bluetooth profiles to print:
SPP Serial Port Profile. OPP Object Push Profile (vCard and vCalendar). HCRP Hardcopy Cable Replacement Profile. A PCL 3 or higher enabled printer with parallel port (IEEE 1284-B). Please order converter cable (MPI Tech p/n 999034-030) if your printer is equipped with a small parallel port connector (IEEE 1284-C). BLUETOOTH PRINTING Please refer to the documentation that came with your Bluetooth device, e.g. laptop, PDA or mobile phone. At our web site you will find instructions for Bluetooth Printing. Please refer to www.mpitech.com/btpa A - CONNECT HARDWARE Follow the steps below to connect the hard-
ware:
Power off your printer. Connect the Bluetooth Printer Adapter to the parallel port of the printer and secure it using the two mounting clips. Connect the included power adapter to the Bluetooth Printer Adapter and to the power out-
let. Power on the printer. The test page is printed after approx. 20 sec-
onds. The Bluetooth Printer Adapter can now be used for Bluetooth printing. B - LIGHT INDICATORS At power on the blue light is on for approx. 20 seconds, where after it starts to flash (indicat-
ing it is ready). The blue light is on whenever a connection has been established to another Bluetooth device. The yellow light indicates that data is available. C - ADDITIONAL PRINT OF TEST PAGE Press the Bluetooth Printer Adapters TEST but-
ton to print the test page. The test page con-
tains information about the Product Version
(500.xxx) and the Bluetooth Device Address
(00:03:6E:XX:XX:XX). REGULATORY INFORMATION This product complies with any mandatory product specification in any country where the product is sold. In addition, the product complies with the following directives:
SAFETY REGULATIONS NOTE: Only use this product with a Class 2 Direct Plug-
In Transformer rated 5.0-> 5.5 Vdc minimun 0.40 A United States of America and Canada The equipment is tested to comply with UL1950 3rd edition and marked in accordance with UL and cUL marks. European Union The product is tested to comply with the Low voltage Directive 73/23/EEC according to EN60950 with amend-
ments. RADIO EQUIPMENT REGULATIONS European Union This equipment complies with the R&TTE directive 1999/5/EC and has been pro-vided with the CE mark accordingly. Note that the radio frequency band used by this equipment has not been harmonized in all of the EU. United States of America and Canada Tested to comply with FCC Standards FOR HOME OR OFFICE USE. See FCC 47CFR part 15.19(b)(2). This device complies with part 15 of the FCC rules and with RSS-210 / RSS-139 of the Industry Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause unde-
sired operation. CAUTION: Any changes or modifications to this equip-
ment not expressly approved by the manufacturer may void the FCC authorization to operate this equipment. Canada (IC notice) To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment that is installed outdoors is subject to licensing. ELECTRONIC EMISSION NOTICES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired oper-
ation. Industry Canada Class B emission compliance state-
ment Federal Communications Commission (FCC) Statement This Class B digital apparatus complies with Canadian ICES-003. European Union EMC Directive conformance state-
ment This product is in conformity with the protection requirements of EU Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. MPI Tech can-
not accept responsibility for any failure to satisfy the protection requirements resulting from a non-recom-
mended modification of the product. This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to CISPR 22/European Standard EN 55022. The limits for Class B equipment were derived for typical residential environments to provide reasonable protection against interference with licensed communication devices. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio fre-
quency, energy and, if not installed and used in accor-
dance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected. Consult an MPI Tech authorized dealer or service rep-
resentative for help. Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Proper cables and connectors are available from MPI Tech authorized dealers. MPI Tech is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equip-
ment. Unauthorized changes or modifications could void the users authority to operate the equipment. E S P A N O L
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2001-06-26 | 2402 ~ 2480 | DSS - Part 15 Spread Spectrum Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2001-06-26
|
||||
1 | Applicant's complete, legal business name |
I-Data International A/S
|
||||
1 | FCC Registration Number (FRN) |
9999999999
|
||||
1 | Physical Address |
Vadstrupvej 35-43
|
||||
1 |
DK-2880 Bagsvaerd, N/A
|
|||||
1 |
Denmark
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
h******@americanTCB.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
OK6
|
||||
1 | Equipment Product Code |
X42100
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
K**** B****** J****
|
||||
1 | Title |
Manager, Approvals & Safety
|
||||
1 | Telephone Number |
45 44********
|
||||
1 | Fax Number |
45 44********
|
||||
1 |
k******@i-data.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
I-data International A-S
|
||||
1 | Name |
K****** B******
|
||||
1 | Physical Address |
Vadstrupvej 35-45
|
||||
1 |
Bagsvaerd, DK-2880
|
|||||
1 |
Denmark
|
|||||
1 | Telephone Number |
+45 4********
|
||||
1 | Fax Number |
+45 4********
|
||||
1 |
k******@i-data.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DSS - Part 15 Spread Spectrum Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Bluetooth Printer Adapter | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power Output listed is Conducted. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Telelaboratoriet-TDC Mobil A/S
|
||||
1 | Name |
M**** A******
|
||||
1 | Telephone Number |
45 43********
|
||||
1 | Fax Number |
45 43********
|
||||
1 |
m******@tdc.dk
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 2402.00000000 | 2480.00000000 | 0.1000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC