FCC ID: Y9E-IAD-18010A Digital Signage Media Appliance

CAUTION Risk of explosion if the battery is replaced by an incorrect type. Wait one-half hour after switching off before handling parts.

- Replacement of a battery with an incorrect type that can be defeat a safeguard;

- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;

- Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas;

- A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. FCC Radiation Exposure Statement:

This equipment complies with FCC RF radiation exposure and Industry Canada RSS-102 RF exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure and Industry Canada RSS-102 RF exposure compliance requirements, this grant is applicable to only Mobile Configura-

tions. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Cet equipement est conforme aux limites dexposition aux rayonnements enoncees pour un environnement non controle et respecte les regles dexposition aux frequences radioe lectriques (RF) CNR-102 de IIC. Cet equipement doit etre installe et utilize en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain (a Iexception des extremites : mains, poignets, pieds et chevilles). This device is restricted to indoor use due to its operation in the 5.15 to 5.25GHz frequency range. Les dispositifs fonctionnant dans la bande 5.15-5.25GHz sont reserves uniquement pour une utilisation l'intrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. Company Name: IAdea Corporation Address: 3F, No. 21, Lane 168, Xingshan Road,Neihu Dist. Taipei, 114 Taiwan Tel: 886-2-2791-1110 WRP-1000 (V2) Series Quick Start Guide Mounting and Installation Option 1: Flush Wall Mount Step 1 Step 2 Step 3 This is a quick walkthrough of the set up process. For complete documentations and quick start guides, please visit http://support.IAdea.com. Box Content Front View 261.7*181.6(mm) x 3 x 2

(1 Spare)

(1 Spare) Room booking panel Mounting plate Glass mount sticker Mounting guide sheet Glass mount cover sheet NFC sticker Screw M3*13 Screw M3*6 Paste the mount sheet on the wall Step 4 Drill the four mounting holes Step 5 Install the mounting plate using the four screws Step 6 Step 7 Screw M3*13 Screw M3*13 Screw of cover plate Screw of cover plate Plug in the required cables to the room panel Option 2: Mounting on Glass Step 1 Step 2 Attach the room panel to the mounting plate Lock the room panel to the mounting plate using a screw at each corner The room panel is ready to be brought online Step 3 Step 4 Port Connections 1 4 43 5 11 1 1 2 1 MicroSD ADB Audio USB Reset USB Ethernet Power LED DC Expansion 6 7 8 9 10 11 12 13 14 15 1 Screw Hole 2 Camera*

3 Microphone*

4 LED 5 NFC/RFID reader 6 MicroSD card slot 7 ADB 8 3.5mm audio 9 USB port 10 Reset 11 USB port 12 Ethernet RJ45(PoE+) 13 Power LED 14 12V DC power 15 Expansion*

16 Kensington Lock 17 VESA mount (MIS-D75) Screw spec: M4 Paste sticker on the back of the mounting plate Ensure the glass surface is clean and dry The mount sheet can be temporary fixed on the other side of the glass to locate the area for the cover sheet. 1.Affix the cover sheet to the glass surface. 2.Align the mounting plate to the cover sheet with the kensington lock hole. Affix the mounting plate to the glass surface Step 5 Step 6 Step 7 Step 8 16 17 Screw M3*13 Screw M3*13 Cover sheet Screw of cover plate Screw of cover plate Plug in the required cables to the room panel Attach the room panel to the mounting plate Lock the room panel to the mounting plate using a screw at each corner The room panel is ready to be brought online Option 3: Mounting close to a window frame Step 2 Step 1 Step 3 Step 4 Window frame Window frame Window frame 1 Align the mounting sheet guide parallel to the window frame Drill the four mounting holes Step 5 Window frame Step 6 Window frame Screw M3*6 Screw M3*13 Screw of cover plate Install the mounting plate using the four screws Step 7 Window frame Plug in the required cables to the room panel Attach the room panel to the mounting plate Lock the room panel using a screw at the top, and two screws at the outside corners The room panel is ready to be brought online IAD_DGS_WRP_10EP Q41G78SP05901A

* The functions marked with "*" only appear on certain models. P.6 P.1 P.2 System Setup 1 Boot up room panel 2 4 To change room panel system language, select

(Current Language) .... rations, select Advanced.

configurations:

1 2 3 Set correct time, date, and time zone for properly scheduled playback. Set password to prevent unauthorized access during setup menu. Set network for establishing network connection. 5 Set content Users can set content by clicking "Set Content" to enter the URL or use the desired content manage-ment system to upload the contents onto the room panel. IAD_DGS_WRP_10EP Content Management CARE AND WARNING content management solution. Troubleshooting How do I interrupt playback and enter setup menu?

Use USB mouse to click and hold one corner of the screen for 10 seconds to exit playback and enter setup menu. How do I provide a DEBUG log for a misbehaving room panel to the support team?

Please follow the instructions below to collect the room panel's DEBUG log:

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Prepare a blank USB stick in FAT-32 format. Europe EU Declaration of Conformity Create a folder named "DEBUG" (case insensitive) in the root of USB stick. Make sure the room panel is operating (see welcome screen or playing content). Insert the USB stick into room panel and wait for This device complies with the essential requirements of the Radio Equipment Directive

(2014/53/EU). The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the Radio Equipment Directive This equipment is compliant with Class A of EN55032. In a residential environment this equipment may cause radio interference. 1 2 3 4 5 Within the "DEBUG" folder, is a folder with a string of number as its name. If the string of numbers are all zero's, the debug log has not been collected properly. Repeat step 1-4 again and make sure to wait

. 6 Zip the"DEBUG" folder and send to IAdea Support Team. Resetting room panel to factory default Factory resetting the room panel will result in the removal of all saved contents, to complete the room panel factory resetting process:

1 2 3 4 Use a pen to press and hold the reset button - do not release until Step 4. Insert the power cord. Wait 30 seconds for the system reboot indicating your data is erased. Release the reset button and your room panel will initialize in factory default state. Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. FCC & CE RF Radiation Exposure Statement Caution: To maintain compliance with the FCC & CEs RF exposure guidelines, place the product at least 20cm from nearby persons. The suitable temperature for the Room Booking Panel and Accessory is 0C-40C. Adapter with ferrite must be used with this equipment to ensure compliance with the Class A FCC limits. Power adapter information:

Model No.: WB-24J12R INPUT: 100-240V~50/60Hz OUTPUT: 12V 2.0A Installation height :<2M P.3 P.4 P.5

Designation of U.S. Agent for Service of Process Explanation:

As required by section 2.911(d)(7), the applicant must designate a contact located in the United States for purposes of acting as the applicants agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process. In either scenario, the designation of the U.S. agent for service of process should be provided as an attachment to the equipment authorization application. The applicant must provide a written certification, which must:

i. Be signed by both the applicant and designated agent for service of process, if the agent is different from the applicant. ii. Acknowledge the applicants consent and the designated agents obligation to accept service of process. iii. Provide a physical U.S. address and email for the designated agent. iv. Acknowledge the applicants acceptance to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. NOTE: The U.S. Agent for Service of Process should not be confused with the authorized agent used for signing the 731 form, other cover letters within the application, and agent who may interface with the TCB. Further Clarification provided from the FCC on February 14, 2023 via TCB Council. The Agent for Process of Service:

cannot be a TCB or affiliated with a TCB (e.g. could not be a person who works for a TCB or a company that owns or is owned by the TCB) cannot be a [FCC recognised] Lab or affiliated with a test lab (e.g. could not be a person who works for a Lab or a company that owns or is owned by the Lab) Agent can be Individual Entity or a Company Entity Agent Entity must be located in US, US address/phone Entity acting as Agent must have FRN (best practice, put FRN on Agent Letter) Agent letter does not have to be FCC ID specific, can be general Agent for Grantee For devices being marketed or for which marketing has ceased for less than 1 year, if the Agent for Process of Service changes, then for every TC Number the TCB must request the FCC to put application into Audit Mode and Agent Letter needs to be updated (superseded). IAdea America Corp. 20 Fairbanks, Suite 170 Irvine/CA 92618 Tel: +1-949-305-6489 x200 U.S. Agent Designation for Service of Process

(Applicant and U.S. Agent are Separate Parties) TO: Nemko North America, Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 ATTENTION: FCC Certification Section 2.911(d)(7) Information Designated U.S. Agent Company Name: IAdea America Corp. Contact Name: Yung-Tsai Wang Street Address:20 Fairbanks, Suite 170 City/Province/Zip: Irvine/CA 92618 Telephone No: +1-949-305-6489 x200 Email: clyde.wang@iadea.com FRN #: 0020588661 This letter is to confirm that we (the Designated U.S. Agent) have accepted the responsibility to act as the Designated U.S. Agent for Service of Process as required by section 47 CFR 2.911(d)(7) on behalf of the Applicant noted below. U.S. Agent Signature:

Date: 3/1/2023 Signed by (Printed Name/Title): Yung-Tsai Wang/Director of Product Development The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission-

related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: IAdea Corporation Grantee Code: Y9E Contact Name: Yung-Tsai Wang Street Address: 3F, No. 21, Lane 168, Xingshan Road,Neihu Dist. City/Province/Zip: Taipei/TW 114 Telephone No: +1-949-305-6489x200 Email: clyde.wang@iadea.com Applicant Signature:

Date: 3/1/2023 Signed by (Printed Name/Title): Yung-Tsai Wang / Director of Product Development

Class II permissive change letter We,IAdea Corporation request for C2PC for product: IAD-18010HIAD-18010AIAD-

18010L. Product code:_ DCD/DTS/DXX/NII _____ Description of product as marketed:_ Room Booking Panel __ Certification number: FCCID:_Y9E-IAD-18010HY9E-IAD-18010A Grantee date: 2023-03-15 The changes are below:

Add New 2nd Panel. All the changes do not influence the RF specification. Signature Name: Yung-Tsai Wang Position: Director of product development Company Name: IAdea Corporation Tel: +1-949-305-6489x200 E-Mail: clyde.wang@iadea.com

IAdea Corporation 3F, No. 21, Lane 168, Xingshan Road, NeihuDist., Taipei City 11469, Taiwan, R.O.C. Tel : 886-2-2791- 1110/ Fax: 886-2-2791- 1170 Certification Application Attestation Statements Date: February 2, 2023 Nemko North America, Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 To Whom It May Concern:

Statement for 47 CFR section 2.911(d)(5)(i) ______IAdea Corporation______ certifies that as of the date of the application the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not covered equipment. Additional Explanation: <N/A>

Statement for 47 CFR section 2.911(d)(5)(ii) ______ IAdea Corporation ______ (the applicant) certifies that, as of the date of the filing of this application, the applicant

- is not identified on the Covered List as an entity producing covered equipment.

- is /

Thank you, By:

(Signature) ___ Yung-Tsai Wang_____

(Print name) Title:

____ Director of Product Development ____ Company:

____ IAdea Corporation _____ Telephone:

_ +1-949-305-6489x200 __

DATE Jan. 13, 2023 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID:____ Y9E-IAD-18010A_______ Product Name:___ Room Booking Panel ________ Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

(List here the documents for which you are seeking confidentiality for example ) Schematics Block diagram Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Dated this Jan. 13, 2023 By:

Signature Yung-Tsai Wang Printed Title: Director of product development On behalf of :

IAdea Corporation Telephone:

+1-949-305-6489x200

IAdea Corporation 3F, No. 21, Lane 168, Xingshan Road, NeihuDist., Taipei City 11469, Taiwan, R.O.C. Tel : 886-2-2791- 1110/ Fax: 886-2-2791- 1170 Product Diversity Description Table Diversity Description Input power Power Consumption Brand name /

Trade mark PCB layout Circuit diagram

, , Components Function Size Others Original Model Series Model IAD-18010H IAD-18010A IAD-18010L 12V 12V 12V 1801mA 1703mA 1643mA IAdea None None IAdea None None IAdea None None WIFI Module;

Double NFC Module WIFI Module;

Single NFC Module WIFI Module;

Single NFC Module Relay/GPIO/RS485 Camera/Mic Relay/GPIO/RS485 Camera/Mic No Relay/GPIO/RS485 No Camera/Mic None

None

None

We, IAdea Corporation, declare that the difference between IAD-18010H & IAD-18010A and IAD-18010L are shown in the above table. As for Radio part: these three models WIFI module are the same, but IAD-18010H has double NFC module, IAD-18010A and IAD-18010L only have single NFC module. Name: Yung-Tsai Wang Position: Director of Product Development IAdea Corporation

DATE : Jan. 13, 2023 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: Y9E-IAD-18010A Product Name: Room Booking Panel Request for Short-Term Confidentiality Pursuant to Sections 0.457 and 0.459 of the commission rules, and in accordance with the FCC Public notice dated June 15, 2004 (DA 04-1705), we hereby request short-term confidentiality for the following items prior to marketing the device.:

Test Setup Photos External Photos Internal Photos User Manual The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Dated this Jan. 13, 2023 By:

Signature Yung-Tsai Wang Printed Title: Director of product development On behalf of:

IAdea Corporation Telephone: +1-949-305-6489x200

IAdea Corporation 3F, No. 21, Lane 168, Xingshan Road, Neihu Dist., Taipei City 11469, Taiwan, R.O.C. Tel : 886-2-2791- 1110/ Fax: 886-2-2791- 1170 Attestation Letter Date: Jan. 10, 2023 Federal Communications Commission Authorization and Evaluation Division FCC ID: Y9E-IAD-18010A We, IAdea Corporation, declare that the device does not support channel 12 ~

13 in 2.4 GHz band and any non-US channels in all the operational mode(s) for the following product. Product: Room Booking Panel Model: IAD-18010A; IAD-18010L FCC ID: Y9E-IAD-18010A If you should have any question(s) regarding this declaration, please dont hesitate to contact us. Thank you!

Sincerely, Name: Yung-Tsai Wang Position: Director of product development IAdea Corporation Web site: www.iadea .com V1.0

IAdea Corporation 3F, No. 21, Lane 168, Xingshan Road, NeihuDist., Taipei City 11469, Taiwan, R.O.C. Tel : 886-2-2791-1110/ Fax: 886-2-2791- 1170 Non-SDR (Software Defined Radio) Cover Letter Date: 2023/1/10 Refer to KDB 442812 D01 SDR apps Guide v02r03. The following questions can be used for determining if a radio can elect to be, or must be an SDR. 1. Can the RF parameters of the device be altered through software?

Yes go to 2. No, not an SDR. 2. Can third parties not permitted by the Commission through specific fillings modify, configure, or load different software, or make configuration settings to operate the device or host hardware radio frequency parameters (frequency range, modulation type, maximum output power or other radio parameters) in any other way than granted (or expected to be granted)?

Yes, must be an SDR. No go to 3. 3. Is the device capable of operating in any other way than granted, or will be, granted?

Yes go to 4. No go to 5. 4. Is this a Part 15 client Device as defined in Section 15.202 (as opposed to a master device)?

Yes, qualifies as a part 15 client devices go to 5. No, must be an SDR. 5. Does the manufacturer elect SDR?

Yes, elects to be an SDR. No, Not an SDR. Final conclusion: Not an SDR According to the above questions reply, we can confirm this Room Booking Panel (FCC ID: Y9E-IAD-18010A) must be a Non-SDR. ____________________ Name: Yung-Tsai Wang Position: Director of Product Development IAdea Corporation

IAdea Corporation 3F, No. 21, Lane 168, Xingshan Road, NeihuDist., Taipei City 11469, Taiwan, R.O.C. Tel : 886-2-2791- 1110/ Fax: 886-2-2791- 1170 Date: 2023/1/10 FCC ID: Y9E-IAD-18010A Software Security Description We, IAdea Corporation hereby declare that requirements of IAD- 18010A IAD- 18010L have been met and shown on the following question. Software Security Description 1 . Describe how any software/ firmware update will be obtained, downloaded, and installed. Software that is accessed through manufacturer s website or device s management system, must describe the different levels of security. Description: The software/ firmware aren t provided through website or device s management. 2 . Describe all the radio frequency parameters that are modified by any software/ firmware without any hardware changes. Are these parameters in some way limited, such that, it will not exceed the authorized parameters?

Description: Any software/ firmware can t modify RF parameters that can affect and exceed the authorized RF characteristics. 3. Describe in detail the authentication protocols that are in place to ensure that the source of the software/firmware is legitimate. Describe in detail how the software is protected against modification. Description: The answer is same with question 2 4 . Describe in detail the verification protocols in place to ensure that installed software/ firmware is legitimate. Description: The answer is same with question 2 5 . Describe in detail any encryption methods used to support the use of legitimate software/ firmware. Description: The answer is same with question 2 6 . For a device that can be configured as a master and client ( with active or passive scanning) , explain how the device ensures compliance for each mode? In particular if the device acts as master in some band of operation and client in another; how is compliance ensured in each band of operation?

Description: This device operation as a client and each mode was compliance with the rule. 1 . Explain if any third parties have the capability to operate a US sold device on any other regulatory domain, frequencies, or in any manner that is in violation of the certification. Description: This device isn t provided to any third parties , so there is no case that third parties operate this device. 2. What prevents third parties from loading non-US versions of the General Description Third- Party Access Control IAdea Corporation 3F, No. 21, Lane 168, Xingshan Road, NeihuDist., Taipei City 11469, Taiwan, R.O.C. Tel : 886-2-2791- 1110/ Fax: 886-2-2791- 1170 software/firmware on the device? Describe in detail how the device is protected from flashing and the installation of third-party firmware such as DD-WRT. Description: The answer is same with question 1 3 . For Certified Transmitter modular devices, describe how the module grantee ensures that hosts manufactures fully comply with these software security requirements for U-NII devices. If the module is controlled through driver software loaded in the host, describe how the drivers are controlled and managed such that the modular transmitter parameters are not modified outside the grant of authorization. Description:The answer is same with question 1 Software Security Description 1 . To whom is the UI accessible? ( Professional installer, end user, other. ) Description: Professional installer and end user a) What parameters are viewable to the professional installer/ end-

user?

Description:

RF ON/OFF Search WiFi Access point Connect WiFi access point b) What parameters are accessible or modifiable by the professional installer?

Description: All parameters described in a are accessible and modifiable by the professional installer

( 1 ) Are the parameters in some way limited, so that the installers will not enter parameters that exceed those authorized?

Description: All parameters described do not effect exceed those authorized.

( 2 ) What controls exist that the user cannot operate the device outside its authorization in the U. S. ?

Description: All parameters described in a, user can not operate the device outside its authorization in the us. c) What parameters are accessible or modifiable to by the end- user?

Description: The parameters can not be accessible or modifiable by the end user.

( 1 ) Are the parameters in some way limited, so that the installers will not enter parameters that exceed those authorized?

Description: All parameters was limited , the installers will not enter parameters that exceed those authorized User Configuration Guide IAdea Corporation 3F, No. 21, Lane 168, Xingshan Road, NeihuDist., Taipei City 11469, Taiwan, R.O.C. Tel : 886-2-2791- 1110/ Fax: 886-2-2791- 1170

( 2 ) What controls exist that the user cannot operate the device outside its authorization in the U. S. ?

Description: Because UI is limited as described a, the user can not operate the device outside its authorization. d) Is the country code factory set? Can it be changed in the UI?

Description: Country code is factory set and UI can not change the country code

( 1 ) If so, what controls exist to ensure that the device can only operate within its authorization in the U. S. ?

Description: This question is not valid e) What are the default parameters when the device is restarted?

Description: RF ON Search WiFi Access point idle WiFi access point not connected to Country code US( CH1 - 1 1 ) Cananda( CH1 - 1 1 ) 2. Can the radio be configured in bridge or mesh mode? If yes, an attestation may be required. Further information is available in KDB Publication 905462 D02. Description:NO 3. For a device that can be configured as a master and client (with active or passive scanning), if this is user configurable, describe what controls exist, within the UI, to ensure compliance for each mode. If the device acts as a master in some bands and client in others, how is this configured to ensure compliance?

Description This device operate as a client, and was controlled to ensure compliance. 4. For a device that can be configured as different types of access points, such as point-to-point or point-to-multipoint, and use different types of antennas, describe what controls exist to ensure compliance with applicable limits and the proper antenna is used for each mode of operation. (See Section 15.407(a)) Description: This device can t be configured as different types of access points , such as point to point and point to multipoint If any questions regarding this declaration, please dont hesitate to contact us. Sincerely ________________/Director of product development

( Signature/ Title) Company name: IAdea Corporation