FCC ID: Y9E-IAD-18001 Smart Signboard

CAUTION Risk of explosion if the battery is replaced by an incorrect type. Wait one-half hour after switching off before handling parts.

- Replacement of a battery with an incorrect type that can be defeat a safeguard;

- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion;

- Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas;

- A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. FCC Radiation Exposure Statement:

This equipment complies with FCC RF radiation exposure and Industry Canada RSS-102 RF exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure and Industry Canada RSS-102 RF exposure compliance requirements, this grant is applicable to only Mobile Configura-

tions. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Cet equipement est conforme aux limites dexposition aux rayonnements enoncees pour un environnement non controle et respecte les regles dexposition aux frequences radioe lectriques (RF) CNR-102 de IIC. Cet equipement doit etre installe et utilize en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain (a Iexception des extremites : mains, poignets, pieds et chevilles). This device is restricted to indoor use due to its operation in the 5.15 to 5.25GHz frequency range. Les dispositifs fonctionnant dans la bande 5.15-5.25GHz sont reserves uniquement pour une utilisation l'intrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. Company Name: IAdea Corporation Address: 3F, No. 21, Lane 168, Xingshan Road,Neihu Dist. Taipei, 114 Taiwan Tel: 886-2-2791-1110 Q41G78SP05901A XDS-1078 (A12) Quick Start Guide This is a quick walkthrough of the set up process. For complete documentations and quick start guides, please visit http://support.IAdea.com. Box Content Securing power and network cable Securing SD card 1) Insert both cables 2) Fasten bracket onto the socket 1) Insert SD 2) Fasten SD card bracket card bracket Securing table stand Smart signboard Power and micro SD card brackets Glass mount Mounting and Installation Mounting option 1: VESA mount

- VESA standard: VESA MIS-D75 (75 mm x 75 mm)

- Screw: M4 x 4 mm (excluding the mounting plate thickness) Mounting option 2: using back cover

- Power / SD card brackets MUST NOT be connected when mounting cover

- plate Mounting option 3: glass mount

- 3M VHB Industrial Heavy Duty Mounting Tape (90 mm x 70 mm) Mounting back cover 1) Release the cover plate screw to release cover plate 2) Install cover plate

(thread head height not to exceed 3 mm) 3) Run power and network cable from the bottom and connect to signboard before mounting Screw the table stand into stand screw hole. Supports landscape and portrait setup. Landscape Portrait 1) Order your glass mount kit 2) Scan QR code for user manual 3) Mount your signboard 4) Impress your visitors QR: http://www.iadea.com/wp-content/uploads/2018/10/PGM-001_User-Manual_2018OCT_web.pdf Port Connections USB 3.0 USB 2.0 Ethernet DC P.2 P.6 P.1 System Setup 1 Boot up Plug in Ethernet cable from PSE (Power Supply Equipment) to the media player and it will power on automatically. Once the user has exited the boot up screen, users can go through system configurations in both landscape and portrait orientations. 2 To change smart signboard system language, se-

lect (Current Language) .... rations, select Advanced.

1 2 3 Set correct time, date, and time zone for properly scheduled playback. Set password to prevent unauthorized access during setup menu. Set network for establishing network connection. Set content Users can set content by clicking "Set Content" to enter Solution Store and set custom URL or use the desired content management system to upload the contents onto the smart signboard. Content Management CARE AND WARNING Please consult the Solution Store documentation for information QR: https://support.iadea.com/hc/en-us/articles/360041795652 Troubleshooting How do I interrupt playback and enter setup menu?

Use USB mouse to click and hold one corner of the screen for 10 seconds to exit playback and enter setup menu. How do I provide a DEBUG log for a misbehaving signboard to the support team?

Please follow the instructions below to collect the player's DEBUG log:

1 2 3 4 5 Prepare a blank USB stick in FAT-32 format. Create a folder named "DEBUG" (case insensitive) in the root of USB stick. Make sure the player is operating (see welcome screen or playing content). Insert the USB stick into player and wait for Within the "DEBUG" folder, is a folder with a string of number as its name. If the string of numbers are all zero's, the debug log has not been collected properly. Repeat step 1-4 again and make sure to wait

. 6 Zip the"DEBUG" folder and send to IAdea Support Team. Reseting smart signboard to factory default Factory reseting the smart signboard will result in the removal of all saved con-

to complete the smart signboard factory reseting process:

1 2 3 4 Use a pen to press and hold the reset button - do not release until Step 4. Insert the power cord. Wait 30 seconds for the system reboot indicating your data is erased. Release the reset button and your smart signboard will initialize in factory default state. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Europe EU Declaration of Conformity This device complies with the essential requirements of the Radio Equipment Directive

(2014/53/EU). The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the Radio Equipment Directive This equipment is compliant with Class A of EN55032. In a residential environment this equipment may cause radio interference. Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. FCC & CE RF Radiation Exposure Statement Caution: To maintain compliance with the FCC & CEs RF exposure guidelines, place the product at least 20cm from nearby persons. The suitable temperature for the Room Booking Panel and Accessory is 0C-40C. Adapter with ferrite must be used with this equipment to ensure compliance with the Class A FCC limits. Power adapter information:

Model No.: WB-24J12R INPUT: 100-240V~50/60Hz OUTPUT: 12V 2.0A Installation height :<2M P.3 P.4 P.5

XDS-1078 (A12) Input:12V 2.0A or PoE+(48V 0.5A) USB3.0 output: 5V 900mA Y9E-IAD-18001 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IAdea Corporation

1. Rating label50#PET, 50%

XDS-1078 (A12) Input:12V 2.0A or PoE+(48V 0.5A) USB3.0 output: 5V 900mA Y9E-IAD-18001 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IAdea Corporation

IAdea Corporation 3F, No. 21, Lane 168, Xingshan Road, NeihuDist., Taipei City 11469, Taiwan, R.O.C. Tel : 886-2-2791-1110/ Fax: 886-2-2791- 1170 Non-SDR (Software Defined Radio) Cover Letter Date: 2023/2/20 Refer to KDB 442812 D01 SDR apps Guide v02r03. The following questions can be used for determining if a radio can elect to be, or must be an SDR. 1. Can the RF parameters of the device be altered through software?

Yes go to 2. No, not an SDR. 2. Can third parties not permitted by the Commission through specific fillings modify, configure, or load different software, or make configuration settings to operate the device or host hardware radio frequency parameters (frequency range, modulation type, maximum output power or other radio parameters) in any other way than granted (or expected to be granted)?

Yes, must be an SDR. No go to 3. 3. Is the device capable of operating in any other way than granted, or will be, granted?

Yes go to 4. No go to 5. 4. Is this a Part 15 client Device as defined in Section 15.202 (as opposed to a master device)?

Yes, qualifies as a part 15 client devices go to 5. No, must be an SDR. 5. Does the manufacturer elect SDR?

Yes, elects to be an SDR. No, Not an SDR. Final conclusion: Not an SDR According to the above questions reply, we can confirm this Smart Signboard

(FCC ID: Y9E-IAD-18001) must be a Non-SDR. Name: Yung-Tsai Wang Position: Director of Product Development IAdea Corporation

IAdea Corporation 3F, No. 21, Lane 168, Xingshan Road, NeihuDist., Taipei City 11469, Taiwan, R.O.C. Tel : 886-2-2791- 1110/ Fax: 886-2-2791- 1170 Certification Application Attestation Statements Date: March 22, 2023 FCC ID: Y9E-IAD-18001 Nemko North America, Inc 303 River Road Ottawa, Ontario, Canada K1V 1H2 To Whom It May Concern:

Statement for 47 CFR section 2.911(d)(5)(i) ______IAdea Corporation______ certifies that as of the date of the application the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not covered equipment. Additional Explanation: <N/A>

Statement for 47 CFR section 2.911(d)(5)(ii) ______ IAdea Corporation ______ (the applicant) certifies that, as of the date of the filing of this

- is not application, the applicant identified on the Covered List as an entity producing covered equipment.

- is /

Thank you, By:

__________________________ YungTsai Wang____

(Signature)

(Print name) Title:

____ Director of product development ____ Company:

____ IAdea Corporation _____ Telephone:

_ +1-949-305-6489x200 __