IC-F510F520_F610F620.qxd 02.1.16 1:38 PM Page a (1,1) INSTRUCTION MANUAL VHF TRANSCEIVER iF510 iF520 UHF TRANSCEIVER iF610 iF620 IC-F510F520_F610F620.qxd 02.1.16 1:38 PM Page b (1,1) IMPORTANT READ ALL INSTRUCTIONS carefully and complete-
ly before using the transceiver. SAVE THIS INSTRUCTION MANUAL This instruction manual contains important operating instructions for the and IC-F610/IC-F620 UHF TRANSCEIVER. EXPLICIT DEFINITIONS IC-F510/IC-F520 TRANSCEIVER VHF WORD RWARNING CAUTION NOTE DEFINITION Personal injury, re hazard or electric shock may occur. Equipment damage may occur. If disregarded, inconvenience only. No risk of personal injury, re or electric shock. RRWARNING For compliance with FCC and Industry Canada RF Exposure Requirements, the transmitter antenna installation shall com-
ply with the following two conditions:
1. The transmitter antenna gain shall not exceed 0 dBi 2.The transmitter antenna is required to be located outside of a vehicle and kept at a separation distance of 85 cen-
timeters or more between the transmitter antenna of this device and persons during operation i CAUTIONS RWARNING! NEVER connect the transceiver to an AC outlet. This may pose a re hazard or result in an electric shock. NEVER connect the transceiver to a power source of more than 16 V DC such as a 24 V battery. This connection will ruin the transceiver. NEVER cut the DC power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting, the transceiver might be damaged. NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury. NEVER allow children to touch the transceiver. NEVER expose the transceiver to rain, snow or any liquids. USE supplied microphone only. Other microphones have different pin assignments and may damage the transceiver. DO NOT use or place the transceiver in areas with tem-
IC-F510F520_F610F620.qxd 02.1.16 1:38 PM Page c (1,1) peratures below 22F (30C) or above +140F (+60C) or, in areas subject to direct sunlight, such as the dashboard. AVOID operating the transceiver without running the vehi-
cles engine. The vehicles battery will quickly run out if the transceiver is in transmission while the vehicles engine OFF. AVOID placing the transceiver in excessively dusty envi-
ronments. AVOID placing the transceiver against walls. This will obstruct heat dissipation. AVOID the use of chemical agents such as benzine or alcohol when cleaning, as they damage the transceiver sur-
faces. BE CAREFUL! The transceiver will become hot when operating continuously for long periods. For U.S.A. only CAUTION: Changes or modications to this transceiver, not expressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations. TABLE OF CONTENTS IMPORTANT .................................................................................... i EXPLICIT DEFINITIONS ................................................................. i CAUTIONS ....................................................................................... i TABLE OF CONTENTS .................................................................. ii 1 PANEL DESCRIPTION ........................................................ 16 I Front panel ............................................................................ 1 I Function display .................................................................... 2 I Programmable function keys ................................................ 3 2 OPERATION ...................................................................... 710 I Turning power ON ................................................................ 7 I Channel selection ................................................................. 7 I Receiving and transmitting ................................................... 8 D Transmitting notes .......................................................... 8 D Tx code channel selection .............................................. 9 D Tx code number selection .............................................. 9 D DTMF transmission ........................................................ 9 D Scrambler function ......................................................... 9 D User set mode .............................................................. 10 3 OPTIONAL SmarTrunk II OPERATION ....................... 1112 I SmarTrunk II and conventional modes ............................ 11 I SmarTrunk II operation .................................................... 11 4 CONNECTION AND MAINTENANCE ............................. 1318 I Rear panel and connection ................................................. 13 I Supplied Accessories ......................................................... 14 I Mounting the transceiver ..................................................... 15 D Inverting the Front panel .............................................. 15 D Mounting the Transceiver ............................................. 16 I Optional UT-105/UT-108 installation ................................... 17 I Optional UT-109/UT-110 installation ................................... 17 I Optional OPC-617 installation ............................................. 18 I Antenna ............................................................................... 18 I Fuse replacement ............................................................... 18 I Cleaning ............................................................................. 18 5 OPTIONS ............................................................................... 19 ii IC-F510F520_F610F620.qxd 02.1.16 1:38 PM Page d (1,1) 1 PANEL DESCRIPTION I Front panel q w e r u y t q AF VOLUME CONTROL KNOB Rotate the knob to adjust the audio output level. Minimum audio level is pre-programmed. w LEFT UP/DOWN []/[] KEYS One of several functions can be programmed by your Dealer. (Same as [P0] to [P4] keys) e FUNCTION DISPLAY Displays variety of information, such as an operating chan-
nel number/name, 2/5tone code, DTMF numbers and audi-
ble condition, etc. NOTE: The above functions depend on pre-programming. r RIGHT UP/DOWN [
] KEYS Push to select the operating channel. Can be programmed for one of several functions by your
Dealer. (Same as [P0] to [P4] keys) 1 IC-F510F520_F610F620.qxd 02.1.16 1:38 PM Page e (1,1) PANEL DESCRIPTION 1 t DEALER-PROGRAMMABLE KEYS [P0] to [P4]
Desired functions can be programmed independently by I Function display your Dealer. q w e r t y u i y POWER SWITCH [POWER]
Push to turns the power ON and OFF. The following functions are available at power ON as options:
- Automatic scan start
- Password prompt
- Set mode u MICROPHONE CONNECTOR Connect the supplied microphone or optional DTMF micro-
phone for SmarTrunk II operation here. NEVER connect non-specified microphones. The pin assignments may be different and the transceiver may be damaged. MICROPHONE The supplied microphone has a PTT switch and a hanger hook. The following functions are available when the microphone is on or off hook:
- Automatic scan start when hung on.
- Automatic priority channel selection when hung off.
- Sets to Inaudible condition (mute condition) when hung on.
- Sets to Audible condition (un-mute condition) when hung off. o q TRANSMIT INDICATOR Appears while transmitting or sending a 2/5tone code. w BUSY INDICATOR Appears while the channel is in busy. e SIGNAL STRENGTH METER Indicates relative signal strength level. r LOW POWER INDICATOR Appears when low output power is selected. t AUDIBLE INDICATOR Appears when the channel is in the Audible condition
(unmute condition). y COMPANDER INDICATOR Appears when compander function is activated. 2 IC-F510F520_F610F620.qxd 02.1.16 1:38 PM Page f (1,1) 1 PANEL DESCRIPTION u SCRAMBLER INDICATOR Appears when scrambler function is activated. (Optional UT-
109 (#02)/UT110 (#02) SCRAMBLER UNIT is required.) i 2/5TONE INDICATOR Appears when specied 2/5tone call is received. o ALPHANUMERIC DISPLAY Displays the CH number, 2/5tone indication, DTMF num-
bers, Audible indication, etc. 3 I Programmable function keys The following functions can be assigned to [P0], [P1], [P2],
[P3], [P4], [], [], [
] programmable function keys. Consult your Icom Dealer or System operator for details con-
cerning your transceivers programming. In the following explanations, programmable function names are bracketed, the specic switch used to activate the func-
tion depends on programming.
] and [
[CH UP]
[CH DN]
CH UP AND DOWN KEYS Select an operating channel. Select a transmit code channel after pushing the [TX CH] key. Select a DTMF channel after pushing the
[DTMF] key. Select a scan group wile pushing and holding the [SCAN] key.
[CH1]
[CH2]
[CH3]
[CH4]
[PRI A]
[PRI B]
OPERATING CHANNEL KEYS Select an operating channel directly. PRIORITY CHANNEL KEYS Select priority A or priority B channel with each push. IC-F510F520_F610F620.qxd 02.1.16 1:38 PM Page g (1,1)
[MONI]
[BANK]
BANK KEY Select and determine a bank number. When the optional UT-105 is installed, push [BANK]
then push [CH UP]/[CH DN] to select operating bank number, and then push [BANK] to determine the bank number.
[SCAN A]
[SCAN B]
SCAN START/STOP KEY Push this key to start scanning; and push again to stop. NOTE: Place the microphone on hook to start scanning. Take the microphone off hook to stop scanning. Push and hold this key to indicate the scan group, then push to select the desired group. SCAN TAG KEY Adds or deletes the selected channel to the scan group. LOCK KEY Electronically locks all programmable keys except the following:
[CALL] (incl. [CAL A] and [CAL B]), [MONI] and
[EMER] keys.
[TAG]
[LOCK]
[W/N]
[H/L]
PANEL DESCRIPTION 1 MONITOR KEY Activates one of (or two of) the following func-
tions on each channel independently:
Push and hold the key to unmute the channel (audio is emitted; Audible condition). Push the key to toggle the mute and unmute condi-
tions (toggles Audible and Inaudible). Push the key to mute the channel (sets to Inaudible only). Push the key to unmute the channel (sets to Audible only). Push the key after the communication is finished to send a reset code. NOTE: The unmute condition (Audible condi-
tion) may automatically return to the mute condi-
tion (Inaudible condition) after a specied peri-
od. WIDE/NARROW KEY Push [W/N] to toggle bandwidth between wide or narrow. OUTPUT POWER SELECTION KEYS Select the transmit output power temporarily or permanently depending on the pre-setting. Ask your Dealer or System Operator for the out-
put power level for each selection. 4 IC-F510F520_F610F620.qxd 02.1.16 1:38 PM Page h (1,1) 1 PANEL DESCRIPTION
[ T A ]
[CALL]
[CAL A]
[CAL B]
[EMER]
TALK AROUND KEY Turns the talk around function ON and OFF. The talk around function equalises the transmit frequency to the receive frequency for mobile-
to-mobile communication. CALL KEYS Transmit a 5-tone code. Call transmission is necessary before you call another station depending on your signaling system. The [CAL A] and/or [CAL B] keys may be available when your system employs selective Individual/Group calls. Ask your Dealer which call is assigned to each key. EMERGENCY KEY Push and hold the key to transmit an emergency call. If you want to cancel the emergency call, push
(or push and hold) the key again before trans-
mitting the call. The emergency call is transmitted one time only or repeatedly until receiving a control code depending on the pre-setting. 5
[TX CH]
TX CODE KEY Select a transmit 5-tone code (station code) channel.
[CODE]
TX CODE CHANNEL UP/DOWN KEY Push to selects a TX code channel directory.
[DTMF]
DTMF CHANNEL SELECT KEY Push this key to select a DTMF channel. Push this key, then select the desired DTMF channel using the [
] keys. Push the key to transmit the selected DTMF code.
[TONE]
C. TONE CHANNEL ENTER KEY Push this key then input a continuous tone mem-
ory channel number using [
] keys to change the tone frequency.
IC-F510F520_F610F620.qxd 02.1.16 1:38 PM Page i (1,1)
[ID MR]
ID MEMORY READ KEY Recalls detected ID codes. Push this key, then push [
Up to 5 IDs are memorized. Push and hold this key to erase all memorized IDs.
] for selection.
[GRP]
TRUNKING GROUP KEY Push to select the Trunking group.
[COMP]
MIC COMPANDER KEY Push to toggle the mic compander function ON or OFF.
[SET]
USER SET MODE KEY Changes the contents of the items in the User Set mode. Push and hold [SET] for 1 sec. to enter set mode, push [SET] momentarily to select the item. Push [
] to set the desired level/condition. Push and hold [SET] again to exit set mode.
] and [
User set mode also available via the Power ON function. Please refer p. 10 also. PANEL DESCRIPTION 1
[SCRM]
SCRAMBLER KEY Push and hold to turn the voice scrambler func-
tion ON. Push to turn the voice scrambler function OFF. NOTE:
Optional UT-109 (#02) or UT-110 (#02) VOICE SCRAMBLER UNIT is required.
-UT-109: Non-rolling type. 32 codes are available.
-UT-110: Rolling type. Provides higher communica-
tion security. 1020 (4 groups 255) cods are avail-
able. This transceiver requires version #02 unit, do not install version #01, as they are not compat-
ible. UT-109 and UT-110 require some PC board modifications. Please refer I Optional UT-
109/UT-110 installation. (p.17) Please contact your Dealer for details. 6 IC-F510F520_F610F620.qxd 02.1.16 1:38 PM Page j (1,1) 2 OPERATION I Turning power ON q Push [POWER] to turn the power ON. A power-up alert tone sounds for about 1 sec. and an opening message may appear. I Channel selection Several types channel selections are available, methods may differ according to your system set up. w If the transceiver is programmed for a start up passcode, input digit codes as directed by your Dealer. The keys in the table below can be used for password input:
The transceiver detects numbers in the same block as identical. Therefore 01234 and 56789 are the same. NON-BANK TYPE:
Push [CH UP]/[CH DN] to select the desired operating chan-
nel, in sequence; or, push one of the [CH 1] to [CH 4] to select a channel directly. KEY
[P0]
[P1]
[P2]
[P3]
[P4]
NUMBER 0 5 1 6 2 7 3 8 4 9 e When the PASSWORD indication does not clear after inputting 4 digits, the input code number may be incorrect. Turn power off and start over in this case. BANK-TYPE:
Push [BANK] to select the desired bank number. AUTOMATIC SCAN TYPE:
Channel setting is not necessary for this type. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call or when taking the microphone off hook. 7 IC-F510F520_F610F620.qxd 02.1.16 1:38 PM Page k (1,1) I Receiving and transmitting RECEIVING:
q Push [POWER] to turn the power ON. w Push [CH UP] or [CH DN] to select a channel. e When receiving a call, adjust the audio output level to a comfortable listening level. TRANSMITTING:
r Take the microphone off hook. 5-tone mute may be released (the audible condition is selected and appears). A priority channel may be selected automatically. t Wait for the channel to become clear. appears. The channel is busy when y Push the [CALL] key when initiating a call from your side. Coded audio may be heard from the transceiver, then appears. This operation may not be necessary depending on your signal-
ing system. Ask your Dealer. u While pushing and holding [PTT], speak into the micro-
phone at your normal voice level. i Release [PTT] to receive. IMPORTANT: To maximize the readability of your signal:
(1) Pause briey after pushing [PTT]
(2) Hold the microphone 2 to 5 cm from your mouth, then speak into the microphone at a normal voice level. OPERATION 2 D Transmitting notes Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions:
- The channel is in mute condition (Inaudible condition;
does not appear).
- Channel is busy.
- No matched (or matched) CTCSS is received.
- The selected channel is a receive only channel. Time-out timer After continuous transmission for a pre-programmed period, the time-out timer is activated causing the transceiver to stop transmitting and automatically select receive. Penalty timer Once the time-out timer is activated, transmission is further inhibited for a period determined by the penalty timer. 8 IC-F510F520_F610F620.qxd 02.1.16 1:39 PM Page l (1,1) 2 OPERATION D Tx code channel selection If the transceiver has a [TX CH] key, display can be toggled between the operating channel number (or name) and Tx code channel number (or name). When the Tx code channel number (or name) is displayed, the [CH UP]/[CH DN] keys select the Tx code channel. TO SELECT A TX CHANNEL:
q Push [TX CH] a Tx code channel appears. w Push [CH UP]/[CH DN] to select the desired Tx code channel. e Push [CALL] to transmit the selected Tx code. r Push [TX CH] again to return to the channel display. D Tx code number selection If the transceiver has a [CODE] key, Tx code contents can be changed within the allowable digits. TO SELECT A TX CODE:
q Push [CODE] a Tx code number appears and an allow-
able digit blinks. w Push [CH UP]/[CH DN] to select the desired number at the blinking digit. e Push [CODE] to enter the selected number. r Repeat steps w and e to input all allowed digits. t Push [CALL] to transmit the selected Tx code. 9 D DTMF transmission If the transceiver has a [DTMF] key, the automatic DTMF transmission function is available. Up to 7 DTMF channels are available. q Push [DTMF] a DTMF code channel appears. w Push [CH UP]/[CH DN] to select the desired DTMF chan-
nel. e Push and hold [DTMF] to transmit the selected DTMF. D Scrambler function UT-109 (#02) or UT-110 (#02) optional voice scrambler unit provides high performance private communication between stations with the same scrambler codes. q Push and hold [SCRM] to turn the scrambler function ON. w e Push [SCRM] to turn the function OFF. appears. IC-F510F520_F610F620.qxd 02.1.16 1:39 PM Page m (1,1) D User set mode User set mode is accessed at power ON and allows you to set seldom-changed settings. In this case you can cus-
tomize transceiver operation to suit your preferences and operating style. OPERATION 2 Entering the user set mode:
qWhile pushing and holding [
], push [POWER]
to enter user set mode ON, allowing you to set seldom-
changed settings.
] and [
wPush and hold [P0] to enter user set mode. Push [P0]
] to set the desired level/condition.
] and [
momentarily to select the item. Then push [
Available set mode functions:
Backlight Beep Beep Level SQL Level AF Min level Audio Filter Mic Gain
:AUTO, DIM, OFF or ON
:ON or OFF
:1 to 5 or Link (links to audio output level)
:0 to 255
:0 to 255
:3000, 3400, 0 or 300
:1 to 5 ePush [POWER] (or push and hold [P0]) again to exit set mode. User set mode also available via the programmable key. Please refer p. 6 [SET] section. 10 IC-F510F520_F610F620.qxd 02.1.16 1:39 PM Page n (1,1) 3 OPTIONAL SmarTrunk II OPERATION I SmarTrunk II and conventional modes This transceiver is capable of SmarTrunk II functions. The optional UT-105 allows communication in conventional channels or SmarTrunk II channels. Select a channel bank for SmarTrunk II before trunking operation. Push [BANK] several times to select a channel bank for con-
ventional channels or SmarTrunk II channels.
- Scanning starts when a channel bank for SmarTrunk II opera-
tion is selected.
- Contact your Dealer for channel bank details. NOTE: Optional HM-100TN DTMF MICROPHONE is required. Contact your Dealer for details. I SmarTrunk II operation These features are enabled by a Dealer and may not be available in your system. Contact your Dealer for details. D Placing a telephone call Enter the phone number followed by [1], [M]. A high-pitched beep indicates that the number is accepted. When the called party answers, push the [PTT] switch to talk, and release it to listen. D Calling another local system subscriber Enter the subscriber number followed by [3], [M]. A high-pitched beep indicates that the number is accepted. You hear ringing, then two short beeps when the subscriber answers. If the other subscriber is on another call or out of range, you hear a fast busy signal and the call terminates automatically. D Receiving a call When you hear ringing, push [M] to answer. For a group call, you hear a short ring followed by two short beeps. You do not have to answer a group call to hear it over the air. 11 IC-F510F520_F610F620.qxd 02.1.16 1:39 PM Page o (1,1) D Terminating a call After completing a call, push [#] to disconnect (hang up). IMPORTANT: If one person in the conversation terminates a call, all participants will be cut off. D Last number re-dial Push [M] 2times to automatically re-dial the last called num-
ber. A high-pitched beep indicates that the number is accepted. D Memory speed-dialling To automatically dial a commonly used number from memory:
Push [M] followed by the memory location (09). D Turbo SpeeDial To automatically dial a commonly used number with one push:
Push one of the turbo SpeeDials ([A], [B], [C] or [D]). D Programming memory speed dial q Push and hold [M] until you hear a high-pitched beep. w Enter the memory location (09, A, B, C, D), the telephone or subscriber number, then [1], [M] (or [3], [M] if for another system subscriber). A high-pitched beep indicates successful programming. Memories [A][D] are used for the Turbo SpeeDial. OPTIONAL SmarTrunk II OPERATION 3 D System busy indication If all channels are busy, three low beeps sound after you initi-
ate a call. Try the call again later. D PTT dispatch operation q Push [PTT] once (without dialling) to initiate a dispatch call. w Begin talking after you hear three beeps (one short, high-
pitched, two very-short, low-pitched). e Receiving a dispatch call is indicated by the same three-
beep sequence. It is not necessary to push [M] to answer a dispatch call. D Emergency call Push [0], [M] to initiate an emergency call. Contact your dealer for details. D Clear channel alerting If all channels are busy, the transceiver automatically begins searching for an open channel and beeps every ten seconds. When two short beeps (low-pitched, then high-pitched) are heard, a channel is available. Push [M], [M] immediately to re-
dial the last number. NOTE: For additional operating instructions, contact your Dealer or System Operator. 12 IC-F510F520_F610F620.qxd 02.1.16 1:39 PM Page p (1,1) 4 CONNECTION AND MAINTENANCE I Rear panel and connection Optional speaker
(SP-22) q Antenna w r red:
NEVER connect to a 24 V battery. t Optional cable
(OPC-617) e black:
Supplied DC power cable 12V Battery Crimp Solder Note: Use the terminals for the cable connections. 13 IC-F510F520_F610F620.qxd 02.1.16 1:39 PM Page q (1,1) qANTENNA CONNECTOR Connects to an antenna. Ask your Dealer about antenna selection and placement. wMICROPHONE HANGER Connect the supplied microphone hanger to the vehicles ground for microphone on/off hook functions. (See p. 2) eDC POWER RECEPTACLE Connects to a 12 V DC battery. Pay attention to polari-
ties. NEVER connect to a 24 V battery. This could dam-
age the transceiver. rEXTERNAL SPEAKER JACK Connect a 48 external speaker, if desired. tOPTIONAL CABLE (OPC-617) Connect an external modem unit, LCD backlight control, etc. CONNECTION AND MAINTENANCE 4 I Supplied Accessories q M O I C t w e r y u i o
!0
!1
!2 LCD-STICKER
!3 o Flat washers ...................... 4
!0 Spring washers ................. 4
!1 Nuts ................................... 4
!2 Fuse s (15 A) ..................... 2
!3 Function name stickers*
(1705 LCD SEAL(D)) .............1 q Microphone ...................... 1 w Microphone hanger and screw set ..................... 1 set e Microphone hanger cable . 1 r DC power cable
(OPC-345) ..........................1 t Mounting bracket .............. 1 y Bracket bolts ..................... 4 u Mounting screws (M512) . 4 i Self-tapping screws
(M520) ............................. 4
*Function name stickers There are no names on the programmable function keys since the needed functions can be assigned to these keys. Attach the supplied function name stickers above the appropriate keys. 14 IC-F510F520_F610F620.qxd 02.1.16 1:39 PM Page r (1,1) 4 CONNECTION AND MAINTENANCE I Mounting the transceiver The front panel can be inverted for correct viewing while leav-
ing the built-in speaker facing away from the mounting sur-
face. D Inverting the Front panel q Unscrew the 2-side screws. w Detach the Front panel forward from the transceiver. e Bend the at cable between Front panel and main unit as shown in the following diagram. Flat cable orientation normal bend line inverted bend line to MAIN unit to Front panel r Invert the transceiver 180 degrees clockwise as below. t Re-attach the Front panel to the transceiver. y Tighten the 2 screws. CAUTION:
NEVER rotate the transceiver more than 180 degrees. DO NOT bend the at cable too hard. Damage may occur. NOTE: Be sure to bend the at cable in the correct direction, before turning over (inverting) the transceiver. 15 IC-F510F520_F610F620.qxd 02.1.16 1:39 PM Page s (1,1) CONNECTION AND MAINTENANCE 4 D Mounting the transceiver The universal mounting bracket supplied with your transceiv-
er allows overhead mounting. Mount the transceiver securely with the 4 supplied screws to a thick surface which can support more than 1.5 kg. Flat washer Spring washer When using self-tapping screws 16 IC-F510F520_F610F620.qxd 02.1.16 1:39 PM Page t (1,1) 4 CONNECTION AND MAINTENANCE I Optional UT-105 and UT-108 installation The optional UT-105 and UT-108 units install as follows:
q Turn power OFF, then disconnect the DC power cable. w Unscrew the 4 screws, then remove the bottom cover. e Install the unit as shown in the diagram below. r Replace the bottom cover and screws, then the DC power I Optional UT-109 /UT-110 installation q Turn power OFF, then disconnect the DC power cable. w Unscrew the 4 screws, then remove the bottom cover. e Cut the print pattern on the PCB at the TX mic circuit (A) and RX AF circuit (B) as shown in the following gure. r Install the scrambler unit as shown in the left. t Return the bottom cover and screws to the original posi-
cable. tion. Front panel A B 17 NOTE: Be sure to re-solder above disconnected points, oth-
erwise no TX modulation or AF output is available when you remove the scrambler units. IC-F510F520_F610F620.qxd 02.1.16 1:39 PM Page u (1,1) I Optional OPC-617 installation Install the OPC-617 as shown below. CONNECTION AND MAINTENANCE 4 I Antenna A key element in the performance of any communication sys-
tem is an antenna. Ask your Dealer about antennas and the best places to mount them. I Fuse replacement Two fuses are installed in the supplied DC power cable. If a fuse blows or the transceiver stops functioning, track down the source of the problem, if possible, and replace the dam-
aged fuse with a new rated one. Fuse rating : 15 A, OPTIONAL CABLE PIN ASSIGNMENT t r e w q o i u y q LCD backlit cont. IN w AF OUT e Det. AF OUT r Mod. IN t PTT control IN y Horn drive cont. OUT u AF GND i Det. AF GND o Mod. GND I Cleaning If the transceiver becomes dusty or dirty, wipe it clean with a dry, soft cloth. AVOID the use of solvents such as benzene or alco-
hol, as they may damage transceiver surfaces. 18 IC-F510F520_F610F620.qxd 02.1.16 1:39 PM Page v (1,1) 5 OPTIONS SP-22 EXTERNAL SPEAKER Compact and easy-to-install. Input impedance: 4 Max. input power: 5 W HM-100TN DTMF microphone. SM-25 Desktop microphone. UT-105 SmarTrunk II Logic Board Provides SmarTrunk II capabilities. UT-108 DTMF DECODER UNIT Provides pager and code squelch capabilities. UT-109/UT-110 (#02) VOICE SCRAMBLER UNIT UT-109: Non-rolling type (max. 32 codes) UT-110: Rolling type (max. 1020 codes) UT-111 TRUNKING BOARD Provides trunking oprtation. OPC-617 ACC CABLE Allows you to connect to an external terminal. 19 Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United states, the United Kingdom, Germany, France, Spain, Russia and/or other coun-
tries. SmarTrunk II is a Trademark of SmarTrunk Systems, Inc. IC-F510F520_F610F620.qxd 02.1.16 1:39 PM Page w (1,1) 20 IC-F510F520_F610F620.qxd 02.1.16 1:39 PM Page Z (1,1) Count on us!
A-6120H-1EX Printed in Japan 2002 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan