all | frequencies |
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 3 |
|
Antenna Manual | Users Manual | 98.86 KiB | ||||
1 2 3 |
|
Revised User Manual | Users Manual | 1.41 MiB | ||||
1 2 3 |
|
User Manual | Users Manual | 1.32 MiB | ||||
1 2 3 |
|
Users Manual | Users Manual | 841.23 KiB | ||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | External Photos | |||||||
1 2 3 | RF Exposure Info | |||||||
1 2 3 | RF Exposure Info | |||||||
1 2 3 | RF Exposure Info | |||||||
1 2 3 | Attestation Statements | |||||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | External Photos | |||||||
1 2 3 | External Photos | |||||||
1 2 3 | Internal Photos | |||||||
1 2 3 | Attestation Statements | |||||||
1 2 3 | ID Label/Location Info | |||||||
1 2 3 | RF Exposure Info | |||||||
1 2 3 | RF Exposure Info | |||||||
1 2 3 | Attestation Statements | |||||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | Cover Letter(s) | |||||||
1 2 3 | External Photos | |||||||
1 2 3 | ID Label/Location Info | |||||||
1 2 3 | RF Exposure Info | |||||||
1 2 3 | Test Report | |||||||
1 2 3 | Test Setup Photos |
1 2 3 | Antenna Manual | Users Manual | 98.86 KiB |
FA-SC61UC Antenna Cutting Chart Antenna cap 360 MHz 380 MHz 400 MHz 420 MHz 440 MHz 460 MHz 480 MHz 500 MHz 520 MHz Thank you for purchasing the FA-SC61UC UHF ANTENNA. Please read these instructions thoroughly before using the FA-SC61UC. FA-SC61UC The optimum bandwidth is 8%
of the tuned frequency. For optimum performance tune to the center transmit frequency of the radio. Cutting Instructions q Align the bottom of the anten-
na onto the 0 position of the cutting guide diagram at left. w Mark the antenna at the length corresponding to the desired to be tuned. frequency e Cut the antenna to the marked length. Use a wire cutter that can cut at least 1.2 mm (d) of piano wire. r Apply adhesive to the top of the antenna and attach the supplied antenna cap. Use of Cemedine Co. Super-X No. 8008 black
(Icom number:
8950002910) or similar is recommended. parts NOTE:
Antenna cap must be inser ted after cutting the element otherwise water immersion makes the element damaged. Center frequency
(MHz) 360 380 400 420 440 460 480 500 520 Length
(mm) 185 175 165 156 148 142 136 129 125 0 CAUTION:
Making antenna cuts at other than the prescribed lengths specified could void the user's authority to operate the equipment. A-6532K-1EX-w Printed in Japan 2006-2009 Icom Inc.
1 2 3 | Revised User Manual | Users Manual | 1.41 MiB |
INSTRUCTION MANUAL VHF TRANSCEIVERS iF3011 iF3013 UHF TRANSCEIVERS iF4011 iF4013 This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful inter-
ference. SAFETY TRAINING INFORMATION W ARNING Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as Occupational Use Only, meaning it must be used only during the course of employment by indi-
viduals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the General Population in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for Occupational Use Only. In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans:
FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Fre-
quency Electromagnetic Fields, 3 kHz to 300 GHz. American National Standards Institute (C95.3-1992), IEEE Recom-
mended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields RF and Microwave. The following accessories are authorized for use with this product. Use of accessories other than those specified may result in RF exposure levels exceeding the FCC requirements for wireless RF exposure.; Belt Clip (MB-94), Rechargeable Li-ion Battery Pack (BP-
230N/BP-232N/BP-232H) and Speaker-microphone (HM-131L). To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occu-
pational use, always adhere to the following guide-
lines:
CAU TION i DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio. DO NOT transmit for more than 50% of total radio use time (50%
duty cycle). 50% duty cycle is also applicable to VOX/PTT mode. Transmitting more than 50% of the time can cause FCC RF expo-
sure compliance requirements to be exceeded. The radio is trans-
mitting when the LED indicator lights red. You can cause the radio to transmit by pressing the PTT switch or VOX function. ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the Icom belt-clip which is listed on page 33 when attaching the radio to your belt, etc., to en-
sure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound qual-
ity, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to as-
sure that this radio operates with the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electro-
magnetic radiation such as hospitals, aircraft, and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. ii FOREWORD READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL This instruction manual contains important operating instructions for the IC-F3011/
IC-F3013 vhf transceivers and IC-F4011/IC-F4013 uhf trans-
ceivers. EXPLICIT DEFINITIONS WORD RDANGER!
RWARNING!
CAUTION NOTE DEFINITION Personal death, serious injury or an explo-
sion may occur. Personal injury, fire hazard or electric shock may occur. Equipment damage may occur. If disregarded, inconvenience only. No risk of personal injury, fire or electric shock. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorpo-
rated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. iii PRECAUTIONS R DANGER! NEVER short the terminals of the battery pack. R DANGER! Use and charge only specified Icom battery packs with Icom radios or Icom chargers. Only Icom battery packs are tested and approved for use with Icom radios or charged with Icom chargers. Using third-party or counterfeit battery packs or chargers may cause smoke, fire, or cause the battery to burst. R WARNING! NEVER hold the transceiver so that the an-
tenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 in.) away from the lips and the transceiver is vertical. R WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. CAUTION: NEVER expose the transceiver to rain, snow or any liquids. The transceiver may be damaged. DO NOT push [PTT] when not actually desiring to transmit. DO NOT use or place the transceiver in direct sunlight or in areas with temperatures below 30C (+22F) or above +60C (+140F). DO NOT modify the transceiver. The transceiver warranty does not cover any problems caused by unauthorized modification. MAKE SURE the flexible antenna and battery pack are securely attached to the transceiver, and that the antenna and battery pack are dry before attachment. Exposing the inside of the transceiver to water will result in serious damage to the transceiver. For U.S.A. only CAUTION: Changes or modifications to this device, not expressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations. iv TABLE OF CONTENTS SAFETY TRAINING INFORMATION .................................................... i FOREWORD .......................................................................................iii EXPLICIT DEFINITIONS .....................................................................iii PRECAUTIONS .................................................................................. iv TABLE OF CONTENTS ....................................................................... v 1 ACCESSORIES ......................................................................... 15 Supplied accessories .................................................................. 1 Accessory attachments .............................................................. 2 2 PANEL DESCRIPTION ............................................................ 611 Front, top and side panels .......................................................... 6 LED indicator .............................................................................. 8 Programmable function keys ...................................................... 9 3 CONVENTIONAL OPERATION ............................................. 1215 Turning power ON ..................................................................... 12 Channel selection ..................................................................... 12 Receiving and transmitting ....................................................... 13 Setting the squelch level ........................................................... 15 4 SIGNALING OPERATIONS ................................................... 1617 Call procedure .......................................................................... 16 Emergency Call ........................................................................ 17 DTMF transmission ................................................................... 17 5 BATTERY CHARGING .......................................................... 1825 Caution ..................................................................................... 18 Battery chargers ....................................................................... 21 6 BATTERY CASE .................................................................... 2627 Optional battery case (BP-240) ................................................ 26 7 SWIVEL BELT CLIP .............................................................. 2831 MB-93 contents......................................................................... 28 To attach ................................................................................... 28 To detach .................................................................................. 30 8 OPTIONS ............................................................................... 3235 9 FCC INFORMATION .................................................................... 36 v ACCESSORIES Supplied accessories The following accessories are supplied. Flexible antenna*
Battery pack Battery carger
(with AC adapter) 1 Belt clip Jack cover (with screws)
*This illustration is described with the VHF type. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 1 ACCESSORIES Accessory attachments D Flexible antenna Connect the supplied flexible antenna to the antenna connector. CAUTION:
NEVER carry the transceiver by holding only the antenna. DO NOT connect the antenna other than listed on page 34. Transmitting without an antenna may damage the transceiver. 2 ACCESSORIES 1 D Battery pack To attach the battery pack:
Slide the battery pack on the back of the transceiver in the direction of the arrow (q), then lock it with the battery release button. Slide the battery pack until the battery release button makes a click sound. To remove the battery pack:
Push the battery release button in the direction of the arrow (w) as shown below. The battery pack is then removed. NOTE: Keep the battery terminals clean. Its a good idea to oc-
casionally clean them. NEVER remove or attach the battery pack when the transceiver is wet or soiled. This may result in water or dust getting into the transceiver/battery pack and may result in the transceiver being damaged. q w Battery release button 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 3 1 ACCESSORIES D Jack cover Attach the jack cover when the optional speaker-microphone is not used. To attach the jack cover:
q Attach the jack cover to the To detach the jack cover:
e Remove the screws with a
[SP MIC] connector. w Tighten the screws. phillips screwdriver. r Detach the jack cover for the optional equipment connec-
tion. q w w e e r 4 ACCESSORIES 1 D Belt clip To attach the belt clip:
q Remove the battery pack if it is attached. w Slide the belt clip in the direction of the arrow until the belt clip is locked and makes a click sound. To detach the belt clip:
q Remove the battery pack if it is attached. w Pinch the clip (q), and slide the belt clip in the direction of the arrow (w). w q 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 5 2 PANEL DESCRIPTION Front, top and side panels i u y t q w e Speaker r Microphone q CHANNEL SELECTOR Rotate the channel selector to select the pre-programmed mem-
ory channels. w VOLUME CONTROL [VOL]
Rotate to turn the power ON/OFF and adjust the audio level. 6 PANEL DESCRIPTION 2 e LED INDICATOR (p. 8) Lights red while transmitting. Lights green while receiving a signal, or when the squelch is open. Lights/blinks orange when the matched 2/5-tone code is re-
ceived, according to the pre-programming. (For IC-F3013/
F4013 only) r SPEAKER-MICROPHONE CONNECTOR [SP MIC]
Connects the optional speaker-microphone, earphone, etc.
[SP MIC] jack cover NOTE: Attach the [SP MIC] jack cover when the optional equip-
ment is not used. (p. 4) t DEALER-PROGRAMMABLE KEY [Lower]
The desired function can be assigned by your dealer. (p. 9) y PTT SWITCH [PTT]
Push and hold to transmit; release to receive. u DEALER-PROGRAMMABLE KEY [Upper]
The desired function can be assigned by your dealer. (p. 9) i ANTENNA CONNECTOR Connects the supplied antenna. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 7 2 PANEL DESCRIPTION LED indicator The LED indicator indicates several information as follows;
(Ref.; R=Red, G=Green, O=Orange) TX: Turns Red while transmitting a signal. R RX: Turns Green while receiving a signal. G Fast/Slow scan: Blinks while Fast/Slow scan is activated. F/S Scan G G Low BATT1: You should charge the battery. (blinks slowly) Low BATT1 Low BATT2 Low BATT2: You must charge the battery. (blinks fast) G G G G G G TX low BATT2: Low BATT2 was detected during TX mode. TX Low BATT2 R R R R CH error: Non-programmed channel is selected. R O R O R O R O R O R O R O R O For IC-F3013/IC-F4013 only Call LED (ON): When receiving a matched 2/5-tone. Call LED ON O O Call LED (Blink): When receiving a matched 2/5-tone. Call LED Blink 8 O O PANEL DESCRIPTION 2 Programmable function keys The following functions can be assigned to [Upper] and [Lower]
programmable function keys. Consult your Icom dealer or system operator for details concerning your transceivers programming. D For All models SCAN A KEY Push to start and cancel scanning operation. When the Power ON scan function is turned ON, push to pause the scanning operation. The paused scan restarts after the spec-
ified time period has passed. SCAN B KEY Push to start and cancel scanning operation. In case of transmis-
sion during scan, pauses scanning. The paused scan restarts after the specified time period has passed. PRIORITY CHANNEL KEYS Push to select the Priority A or Priority B channel. Push and hold [Prio A (Rewrite)] to rewrite the Prio A channel. MR-CH 1/2/3/4 KEYS Push to select a memory channels 1 to 4 directly. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 9 2 PANEL DESCRIPTION OUTPUT POWER SELECTION KEY Select the transmit output power temporarily or permanently, de-
pending on the pre-setting. Ask your dealer for the output power level for each selection. TALK AROUND KEY Push to turn the talk around function OFF. Push and hold to turn the talk around function ON. The talk around function equalizes the transmit frequency to the receive frequency for transceiver-to-transceiver communication. WIDE/NARROW KEY Push to select the IF bandwidth to wide. The wide passband width can be selected from 25 or 20 kHz using the optional cloning software (PMR operation only). Ask your dealer for details. Push and hold to select the IF bandwidth to narrow. SIREN KEY Push to emit a siren. This function can be used for situations other than an emergency alert such as a security alarm for example. LOCK KEY Push and hold to electronically lock all programmable keys except the followings: [Moni(Audi)], [Call] (incl. Call A and Call B)* and
[Emergency Single]/[Emergency Repeat] (incl. Silent)*.
* Available for IC-F3013/IC-F4013 only. 10 PANEL DESCRIPTION 2 MONITOR KEY Push to mute and release the CTCSS (DTCS) or 2Tone* squelch mute. Open any squelches/deactivate any mutes while pushing this key. (LMR operation only)
* Available for the IC-F3013/F4013 only. Activates one of (or two of) the following functions on each chan-
nel independently: (PMR operation only) Push and hold to un-mute the channel (audio is emitted; Audible). Push to mute the channel (audio is not emitted; Inaudible). Push to send a reset code after the communication is finished. NOTE: The un-mute condition (Audible condition) may auto-
matically return to the mute condition (Inaudible condition) after a specified period. D For IC-F3013/IC-F4013 only DTMF AUTODIAL KEY Push to transmit the programmed DTMF code. CALL KEYS Push to transmit a 2/5-tone code. Call transmission is necessary before you call another station depend-
ing on your signalling system.
[Call A] and/or [Call B] keys may be available when your system em-
ploys selective Individual/Group calls. Ask your dealer which call is assigned to each key. EMERGENCY SINGLE/EMERGENCY REPEAT KEYS Push and hold for the specified time period to transmit an emer-
gency call once or repeatedly. When [Emergency Single (Silent)] or [Emergency Repeat (Silent)]
is pushed, an emergency call is transmitted with no beep emission. If you want to cancel the emergency call, push (or push and hold) the key again before transmitting the call. The emergency call is transmitted one time only or repeatedly until receiving a control code depending on the pre-setting. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 11 3 CONVENTIONAL OPERATION Turning power ON Rotate [VOL] to turn power ON.
[VOL]
[CHANNEL SELECTOR]
Channel selection Rotate [CHANNEL SELECTOR] to se-
lect the desired operating channel, in sequence; or, push one of [MR-CH 1] to
[MR-CH 4] key to select a channel di-
rectly. AUTOMATIC SCAN TYPE:
Channel setting is not necessary for this type. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call. 12 CONVENTIONAL OPERATION 3 Receiving and transmitting NOTE: Transmitting without an antenna may damage the trans-
ceiver. See page 2 for antenna attachment. Receiving:
q Rotate [VOL] to turn power ON. w Rotate [CHANNEL SELECTOR] or push one of [MR-CH 1] to
[MR-CH 4] key to select a channel. e When receiving a call, adjust the audio output level to a comfort-
able listening level. Transmitting:
Wait for the channel to become clear to avoid interference. q While pushing and holding [PTT], speak into the microphone at a normal voice level. w Release [PTT] to return to receive. IMPORTANT: To maximize the readability of your signal;
1. Pause briefly after pushing [PTT]. 2. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak into the microphone at a normal voice level. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 13 3 CONVENTIONAL OPERATION D Transmitting notes Transmit inhibit function The transceiver has several inhibit functions which restrict trans-
mission under the following conditions:
- The channel is in mute condition.
- The channel is busy.
- Un-matched (or matched) CTCSS is received.
- The selected channel is a receive only channel. Time-out timer After continuous transmission for the pre-programmed time period, the time-out timer activates, and causes the transceiver to stop transmit-
ting. Penalty timer Once the time-out timer activates, transmission is further inhibited for a period determined by the penalty timer. 14 CONVENTIONAL OPERATION 3 Setting the squelch level The squelch circuit mutes the received audio signal depending on the signal strength.
[VOL]
q While pushing [PTT] and [Lower], rotate [VOL] to turn the power ON to enter the squelch level adjust-
ment mode. w Push [Upper] to increase the squelch level (tight squelch) or
[Lower] to decrease the squelch level (loose squelch). e Rotate [VOL] to turn the power OFF to fix the squelch level.
[Upper]
[PTT]
[Lower]
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 15 4 SIGNALING OPERATIONS NOTE: The tone signalling operations are available for the IC-F3013/F4013 only. Call procedure When your system employs tone signalling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice trans-
mission. The tone signalling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from contacting you. q Select the desired TX code channel or 2/5-tone code according to your System Operators instructions. This may not be necessary depending on programming. w Push [Call]. (p. 11) e After transmitting a 2/5-tone code, the remainder of your com-
munication can be carried out in the normal fashion. Selective calling Non-selective calling D Transmitting notes PTTID call The transceiver sends the ID code (5-tone, DTMF or digital ANI) automatically when [PTT] is pushed (beginning of transmission) and released (end of transmission) depends on the setting. 16 SIGNALING OPERATIONS 4 Emergency Call When [Emergency Single] or [Emergency Repeat] (p. 11) is pushed and held for the specified time period, the emergency sig-
nal (5-tone, DTMF or MDC 1200) is transmitted once or repeatedly on the emergency channel. A repeat emergency signal is auto-
matically transmitted until it receives the acknowledgement signal. When no emergency channel is specified, the signal is transmitted on the previously selected channel. If you want to cancel the emergency call, push and hold the key again before transmitting the call. The emergency call can be transmitted without a beep emission, and the LCD indication if [Emergency Single (Silent)] or [Emer-
gency Repeat (Silent)] (p. 11) is pushed. The transceiver can also be programmed to keep the microphone open during an emergency call, allowing monitoring of the situa-
tion. IMPORTANT: It is recommended to set an emergency channel individually to provide the certain emergency call operation. DTMF transmission If the transceiver has [DTMF Autodial] assigned to it, the auto-
matic DTMF transmission function is available. Push [DTMF Autodial] to transmit the DTMF code. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 17 5 BATTERY CHARGING Caution Misuse of Lithium-ion batteries may result in the following hazards: smoke, fire, or the battery may rupture. Misuse can also cause damage to the battery or degradation of battery performance. R DANGER! Use and charge only specified Icom battery packs with Icom radios or Icom charger. Only Icom battery packs are tested and approved for use and charge with Icom radios or Icom charger. Using third-party or counterfeit battery packs or charger may cause smoke, fire, or cause the battery to burst. D Battery caution R DANGER! DO NOT hammer or otherwise impact the battery. Do not use the battery if it has been severely impacted or dropped, or if the battery has been subjected to heavy pressure. Battery damage may not be visible on the outside of the case. Even if the surface of the battery does not show cracks or any other damage, the cells inside the battery may rupture or catch fire. R DANGER! NEVER use or leave battery packs in areas with temperatures above +60C (+140F). High temperature buildup in the battery, such as could occur near fires or stoves, inside a sun heated car, or in direct sunlight may cause the battery to rupture or catch fire. Excessive temperatures may also degrade battery per-
formance or shorten battery life. R DANGER! DO NOT expose the battery to rain, snow, seawater, or any other liquids. Do not charge or use a wet battery. If the bat-
tery gets wet, be sure to wipe it dry before using. The battery is not waterproof. 18 BATTERY CHARGING 5 R DANGER! NEVER incinerate used battery packs since internal battery gas may cause them to rupture, or may cause an explosion. R DANGER! NEVER solder the battery terminals or NEVER mod-
ify the battery pack. This may cause heat generation, and the bat-
tery may rupture, emit smoke or catch fire. R DANGER! Use the battery only with the transceiver for which it is specified. Never use a battery with any other equipment, or for any purpose that is not specified in this instruction manual. R DANGER! If fluid from inside the battery gets in your eyes, blind-
ness can result. Rinse your eyes with clean water, without rubbing them, and see a doctor immediately. WARNING! Immediately stop using the battery if it emits an ab-
normal odor, heats up, or is discolored or deformed. If any of these conditions occur, contact your Icom dealer or distributor. WARNING! Immediately wash, using clean water, any part of the body that comes into contact with fluid from inside the battery. WARNING! NEVER put the battery in a microwave oven, high-
pressure container, or in an induction heating cooker. This could cause a fire, overheating, or cause the battery to rupture. CAUTION! Always use the battery within the specified temperature range for the transceiver (30C to +60C; 22F to +140F) and the battery itself (20C to +60C; 4F to +140F). Using the bat-
tery out of its specified temperature range will reduce the batterys performance and battery life. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 19 5 BATTERY CHARGING CAUTION! Shorter battery life could occur if the battery is left fully charged, completely discharged, or in an excessive temperature environment (above +50C; +122F) for an extended period of time. If the battery must be left unused for a long time, it must be de-
tached from the radio after discharging. You may use the battery until the remaining capacity is about half, then keep it safely in a cool dry place with the temperature range as below:
20C to +50C (4F to +122F) 20C to +40C (4F to +95F) 20C to +20C (4F to +68F)
(within a month)
(within three months)
(within a year) D Charging caution R DANGER! NEVER charge the battery pack in areas with ex-
tremely high temperatures, such as near fires or stoves, inside a sun heated car, or in direct sunlight. In such environments, the safety/protection circuit in the battery will activate, causing the bat-
tery to stop charging. WARNING! DO NOT charge or leave the battery in the battery charger beyond the specified time for charging. If the battery is not completely charged by the specified time, stop charging and re-
move the battery from the battery charger. Continuing to charge the battery beyond the specified time limit may cause a fire, overheat-
ing, or the battery may rupture. WARNING! NEVER insert the transceiver (battery attached to the transceiver) into the charger if it is wet or soiled. This could corrode the battery charger terminals or damage the charger. The charger is not waterproof. CAUTION! DO NOT charge the battery outside of the specified temperature range: BC-160 (0C to +40C; +32F to +104F). Icom recommends charging the battery at +20C (+68F). The battery may heat up or rupture if charged out of the specified temperature range. Additionally, battery performance or battery life may be re-
duced. 20 BATTERY CHARGING 5 Battery chargers D Rapid charging with the BC-160 The optional BC-160 provides rapid charging of the Li-ion battery pack. Charging period: Approximately 3 hours (with BP-232H) The following items are additionally required:
An AC adapter (not supplied with some versions) or the DC power cable (OPC-515L/CP-23L) is additionally required. AC adapter
(A different type, or no AC adapter is supplied, depending on the version.) Battery pack Transceiver Turn power OFF Optional OPC-515L*
(for power source) or CP-23L (for 12 V ciga-
rette lighter socket) can be used instead of the AC adapter.
About OPC-515L White line:
Black line :
Tabs IMPORTANT!
Ensure the guide tabs on the battery pack are correctly aligned with the guide rails inside the charger adapter. Guide rail 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 5 BATTERY CHARGING D Regular charging with the BC-171 The optional BC-171 provides regular charging of the Li-ion battery pack. Charging period: Approximately 10 hours (with BP-232H) The following items are additionally required:
An AC adapter (not supplied with some versions) or the DC power cable (OPC-515L/CP-23L) is additionally required. AC adapter
(A different type, or no AC adapter is supplied, depending on the version.) Battery pack Transceiver Turn power OFF Optional OPC-515L*
(for power source) or CP-23L (for 12 V ciga-
rette lighter socket) can be used instead of the AC adapter.
About OPC-515L White line:
Black line :
Tabs IMPORTANT!
Ensure the guide tabs on the battery pack are correctly aligned with the guide rails inside the charger adapter. Guide rail 22 BATTERY CHARGING 5 D AD-106 installation The AD-106 charger adapter must be installed into the BC-119N or BC-121N before battery charging. q Attach the plugs from the BC-119N/BC-121N to the AD-106 charger adapter. w Secure the AD-106 into the holder space of the BC-119N/BC-
121N with the supplied screws. Plugs Desktop charger adapter Sockets Screws supplied with the charger adapter This illustration is described with the BC-119N. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 23 5 BATTERY CHARGING D Rapid charging with the BC-119N+AD-106 The optional BC-119N provides rapid charging of the Li-ion battery pack. Charging period: Approximately 3 hours (with BP-232H) The following items are additionally required:
An AD-106 charger adapter (purchase separately) An AC adapter (not supplied with some versions) or the DC power cable (OPC-515L/CP-23L). Transceiver Turn power OFF Battery pack AC adapter
(A different type, or no AC adapter is supplied, de-
pending on the version.) AD-106 charger adapter is installed in BC-119N. Optional OPC-515L*
(for power source) or CP-23L (for 12 V ciga-
rette lighter socket) can be used instead of the AC adapter.
About OPC-515L White line:
Black line :
24 IMPORTANT!
Ensure the guide tabs on the battery pack are correctly aligned with the guide rails inside the charger adapter. Guide rails Tabs BATTERY CHARGING D Rapid charging with the BC-121N+AD-106 The optional BC-121N allows up to 6 battery packs to be charged simultaneously. Charging period: Approximately 3 hours (with BP-232H) 5 The following items are additionally required. Six AD-106 charger adapter (purchase separately) An AC adapter (BC-157) or the DC power cable (OPC-656) Battery pack Turn power OFF Transceiver AD-106 charger adapters are installed in each slot. AC adapter
(Purchase separately) Tabs IMPORTANT!
Ensure the guide tabs on the battery pack are correctly aligned with the guide rails inside the charger adapter. Guide rails DC power cable
(OPC-656*)
(Connect with a DC power supply; 13.8 V/at least 7 A)
*About the OPC-656 Red line: Black line:
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 25 6 BATTERY CASE Optional battery case (BP-240) When using the optional battery case, install 6 AAA (LR03) size alkaline batteries as illustrated at right. q Unhook the battery cover release hook (q), and open the cover in the direction of the arrow (w). (Fig.1) Install the alkaline batteries only. Be sure to observe the correct polarity. w Then, install 6 AAA (LR03) size alkaline batteries. (Fig.2) e Fit the cover in the direction of the arrow (e), then close (r). Hook the battery cover release hook until it makes a click sound
(t). (Fig.3) CAUTION:
When installing batteries, make sure they are all the same brand, type and capacity. Also, do not mix new and old batter-
ies together. Keep battery contacts clean. Its a good idea to occasionally clean them. Never incinerate used battery cells since internal battery gas may cause them to rupture. Never expose a detached battery case to water. If the battery case gets wet, be sure to wipe it dry before using it. NOTE: When the optional battery case is attached, the battery type must be selected to Alkaline battery operation when turn-
ing the transceiver ON. Ask your dealer for details. 26 Fig.1 Fig.2 Fig.3 BATTERY CASE 6 w BP-240 q e r t 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 27 7 SWIVEL BELT CLIP MB-93 contents Qty. q Belt clip .................................................................................... 1 w Base clip .................................................................................. 1 q w To attach q Remove the battery pack if it is attached. (p. 3) w Slide the base clip in the direction of the arrow until the base clip is locked and makes a click sound. 28 7 e Clip the belt clip to a part of your belt. And insert the transceiver into the belt clip until the base clip inserted fully into the groove. SWIVEL BELT CLIP r Once the transceiver is locked in place, it swivels as illustrated below. Once the transceiver is locked in place, it will swivel 360 degrees. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 29 7 SWIVEL BELT CLIP To detach q Turn the transceiver upside down in the direction of the arrow and pull out from the belt clip. 30 SWIVEL BELT CLIP 7 w Remove the battery pack if it is attached. (p. 3) e Pinch the clip (q), and slide the base clip in the direction of the arrow (w). q w CAUTION:
HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR DETACHING THE TRANSCEIVER FROM THE BELT CLIP. Otherwise the transceiver may not be attached to the holder or swivel properly if the transceiver is accidentally dropped and the base clip is scratched or damaged. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 31 8 OPTIONS D BATTERY PACK Battery pack Voltage Capacity Battery life*1 BP-230N 7.4 V BP-232N 7.4 V BP-232H 7.4 V 950 mAh (min.) 980 mAh (typ.) 1900 mAh (min.) 2000 mAh (typ.) 2250 mAh (min.) 2300 mAh (typ.) BP-240 Battery case for AAA
(LR03) 6 alkaline 9 hrs. 18 hrs. 21 hrs.
*2
*1 When the power save function is turned ON, and the operating pe-
riods are calculated under the following conditions;
TX : RX : standby = 5 : 5 : 90
*2 Operating period depends on the alkaline cells used. D CHARGERS BC-119N desktop charger + AD-106 charger adapter
+ BC-145S ac adapter For rapid charging of battery packs. An AC adapter is supplied with the charger depending on versions. Charging time: Approximately 3 hours when BP-232H is attached. BC-121N multi-charger + AD-106 charger adapter (6 pcs.)
+ BC-157 ac adapter For rapid charging of up to 6 battery packs (six AD-106s are required) simultaneously. An AC adapter should be purchased separately. Charging time: Approximately 3 hours when BP-232H is attached. 32 OPTIONS 8 BC-160 desktop charger + BC-145S ac adapter For rapid charging of battery packs. An AC adapter is supplied with the charger depending on versions. Charging time: Approximately 3 hours when BP-232H is attached. BC-171 desktop charger + BC-147S ac adapter For regular charging of battery packs. We recommend that the BP-230N charging. An AC adapter is supplied with the charger depending on versions. Charging time: Approximately 11 hours when BP-232H is attached. Approximately 4 hours when BP-230N is attached. D BELT CLIPS MB-93 swivel belt clip MB-94 belt clip Exclusive alligator-type belt clip. MB-96N/96F leather belt hanger D DC CABLES CP-23L cigarette lighter cable Allows charging of the battery pack through a 12 V cigarette lighter socket. (For BC-119N/BC-160/BC-171) OPC-515L/OPC-656 dc power cables Allows charging of the battery pack using a 13.8 V power source instead of the AC adapter. OPC-515L: For BC-119N/BC-160/BC-171 OPC-656 : For BC-121N 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 33 8 OPTIONS D ANTENNAS FA-SC73US/FA-SC56VS/FA-SC57VS stubby antennas FA-SC73US: 450490 MHz FA-SC57VS: 160174 MHz FA-SC01U/FA-SC25U/FA-SC57U/FA-SC72U/FA-SC25V/
FA-SC56VS: 150162 MHz FA-SC55V antennas FA-SC01U: 350400 MHz FA-SC57U: 430470 MHz FA-SC25V: 136155 MHz FA-SC61VC/FA-SC61UC cut antennas FA-SC61VC: 136174 MHz FA-SC25U: 400430 MHz FA-SC72U: 470520 MHz FA-SC55V: 146174 MHz FA-SC61UC: 380520 MHz D OTHER OPTIONS SP-13 earphone Provides clear receive audio in noisy environment. HM-153L earphone-microphone HM-131L/158L/159L speaker-microphone Combination speaker-microphone that provides convenient op-
eration while hanging the transceiver from your belt. VS-1L vox/ptt case + HS-94/HS-95/HS-97 headset VS-1L: VOX/PTT switch box for hands-free operation, etc. HS-94: Ear hook type HS-97: Throat microphone MB-130 vehicle charger bracket Vehicle mounting bracket for the BC-160 battery charger. HS-95: Neck-arm type Approved Icom optional equipment is designed for optimal performance when used with an Icom transceiver. Icom is not responsible for the destruction or damage to an Icom trans-
ceiver in the event the Icom transceiver is used with equipment that is not manufactured or approved by Icom. Some options may not be available in some countries. Please ask your dealer for details. 34 OPTIONS 8 D About VS-1L vox/ptt case The VS-1L is a VOX/PTT unit for Icom handheld transceivers, and allows you hands-free operation. An optional headset (HS-94, etc.) is additionally required for opera-
tion. The VOX (voice operated transmission) function starts transmission without pushing PTT switch when you speak into the microphone;
then, automatically returns to receive when you stop speaking. Features Straight type head SP/MIC plug equipped Water resistant construction Durable construction Equipped with a PTT switch and revolving clip. MIC/VOX gain adjustment 1 Remove the water protection cover on the right side of the VS-1L. 2 Adjust the MIC/VOX gain with a thin screw driver. Clockwise rota-
tion increases the MIC/VOX gain. 3 Return the protective cover back to the MIC/VOX gain adjustment hole. Adjusting pot VS-1L PTT switch Water protection cover VOX PTT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 35 9 FCC INFORMATION FOR CLASS B UNINTENTIONAL RADIATORS:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 36 MEMO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 MEMO MEMO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 MEMO MEMO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 A-6768H-1EX-w Printed in Japan 20092012 Icom Inc. Printed on recycled paper with soy ink. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
1 2 3 | User Manual | Users Manual | 1.32 MiB |
INSTRUCTION MANUAL VHF TRANSCEIVERS iF3011 iF3013 UHF TRANSCEIVERS iF4011 iF4013 This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful inter-
ference. SAFETY TRAINING INFORMATION W ARNING Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as Occupational Use Only, meaning it must be used only during the course of employment by indi-
viduals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the General Population in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for Occupational Use Only. In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans:
FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Fre-
quency Electromagnetic Fields, 3 kHz to 300 GHz. American National Standards Institute (C95.3-1992), IEEE Recom-
mended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields RF and Microwave. The following accessories are authorized for use with this product. Use of accessories other than those specified may result in RF ex-
posure levels exceeding the FCC requirements for wireless RF ex-
posure.; Belt Clip (MB-94), Rechargeable Li-Ion Battery Pack (BP-
230N/BP-232N) and Speaker-microphone (HM-131L). To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occu-
pational use, always adhere to the following guide-
lines:
CAU TION i DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio. DO NOT transmit for more than 50% of total radio use time (50%
duty cycle). 50% duty cycle is also applicable to VOX/PTT mode. Transmitting more than 50% of the time can cause FCC RF expo-
sure compliance requirements to be exceeded. The radio is trans-
mitting when the LED indicator lights red. You can cause the radio to transmit by pressing the PTT switch or VOX function. ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the Icom belt-clip which is listed on page 33 when attaching the radio to your belt, etc., to en-
sure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound qual-
ity, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to as-
sure that this radio operates with the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electro-
magnetic radiation such as hospitals, aircraft, and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. ii FOREWORD READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL This instruction manual contains important operating instructions for the IC-F3011/
IC-F3013 vhf transceivers and IC-F4011/IC-F4013 uhf trans-
ceivers. EXPLICIT DEFINITIONS WORD RDANGER RWARNING CAUTION NOTE DEFINITION Personal death, serious injury or an explo-
sion may occur. Personal injury, fire hazard or electric shock may occur. Equipment damage may occur. If disregarded, inconvenience only. No risk of personal injury, fire or electric shock. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorpo-
rated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. iii PRECAUTIONS R CAUTION! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 in.) away from the lips and the transceiver is vertical. R CAUTION! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. R CAUTION! NEVER short the terminals of the battery pack. R CAUTION! NEVER use non-Icom battery packs/chargers to prevent the loss of the transceivers good performance and warranty. R CAUTION! NEVER expose the transceiver to rain, snow or any liquids. The transceiver may be damaged. DO NOT push [PTT] when not actually desiring to transmit. DO NOT use or place the transceiver in direct sunlight or in areas with temperatures below 30C (+22F) or above +60C (+140F). DO NOT modify the transceiver. The transceiver warranty does not cover any problems caused by unauthorized modification. MAKE SURE the flexible antenna and battery pack are securely attached to the transceiver, and that the antenna and battery pack are dry before attachment. Exposing the inside of the transceiver to water will result in serious damage to the transceiver. The use of non-Icom battery packs/chargers may impair trans-
ceiver performance and invalidate the warranty. For U.S.A. only CAUTION! Changes or modifications to this device, not expressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations. iv TABLE OF CONTENTS SAFETY TRAINING INFORMATION .................................................... i FOREWORD .......................................................................................iii EXPLICIT DEFINITIONS .....................................................................iii PRECAUTIONS .................................................................................. iv TABLE OF CONTENTS ....................................................................... v 1 ACCESSORIES ......................................................................... 15 Supplied accessories .................................................................. 1 Accessory attachments .............................................................. 2 2 PANEL DESCRIPTION ............................................................ 611 Front, top and side panels .......................................................... 6 LED indicator .............................................................................. 8 Programmable function keys ...................................................... 9 3 CONVENTIONAL OPERATION ............................................. 1215 Turning power ON ..................................................................... 12 Channel selection ..................................................................... 12 Receiving and transmitting ....................................................... 13 Setting the squelch level ........................................................... 15 4 SIGNALING OPERATIONS ................................................... 1617 Call procedure .......................................................................... 16 Emergency Call ........................................................................ 17 DTMF transmission ................................................................... 17 5 BATTERY CHARGING .......................................................... 1825 Caution ..................................................................................... 18 Battery chargers ....................................................................... 21 6 BATTERY CASE .................................................................... 2627 Optional battery case (BP-240) ................................................ 26 7 SWIVEL BELT CLIP .............................................................. 2831 MB-93 contents......................................................................... 28 To attach ................................................................................... 28 To detach .................................................................................. 30 8 OPTIONS ............................................................................... 3235 9 FCC INFORMATION .................................................................... 36 ACCESSORIES Supplied accessories The following accessories are supplied. Flexible antenna*
Battery pack Battery carger
(with AC adapter) 1 Belt clip Jack cover (with screws)
*This illustration is described with the VHF type. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1 1 ACCESSORIES Accessory attachments D Flexible antenna Connect the supplied flexible antenna to the antenna connector. CAUTION:
NEVER HOLD the antenna when carrying the transceiver. Transmitting without an antenna may damage the transceiver. 2 ACCESSORIES 1 D Battery pack To attach the battery pack:
Slide the battery pack on the back of the transceiver in the direction of the arrow (q), then lock it with the battery release button. Slide the battery pack until the battery release button makes a click sound. To release the battery pack:
Push the battery release button in the direction of the arrow (w) as shown below. The battery pack is then released. NEVER release or attach the battery pack when the transceiver is wet or soiled. This may result in water or dust getting into the transceiver/battery pack and may result in the transceiver being damaged. q w Battery release button 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 3 1 ACCESSORIES D Jack cover Attach the jack cover when the optional speaker-microphone is not used. To attach the jack cover:
q Attach the jack cover to the To detach the jack cover:
e Unscrew the screws with a
[SP MIC] connector. w Tighten the screws. phillips screwdriver. r Detach the jack cover for the optional equipment connec-
tion. q w w e e r 4 ACCESSORIES 1 D Belt clip To attach the belt clip:
q Release the battery pack if it is attached. w Slide the belt clip in the direction of the arrow until the belt clip is locked and makes a click sound. To detach the belt clip:
q Release the battery pack if it is attached. w Pinch the clip (q), and slide the belt clip in the direction of the arrow (w). w q 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 5 2 PANEL DESCRIPTION Front, top and side panels i u y t q w e Speaker r Microphone q CHANNEL SELECTOR Rotate the channel selector to select the pre-programmed mem-
ory channels. w VOLUME CONTROL [VOL]
Rotate to turn the power ON/OFF and adjust the audio level. 6 PANEL DESCRIPTION 2 e LED INDICATOR (p. 8) Lights red while transmitting. Lights green while receiving a signal, or when the squelch is open. Lights/blinks orange when the matched 2/5-tone code is re-
ceived, according to the pre-programming. (For IC-F3013/
F4013 only) r SPEAKER-MICROPHONE CONNECTOR [SP MIC]
Connects the optional speaker-microphone, earphone, etc.
[SP MIC] jack cover NOTE: Attach the [SP MIC] jack cover when the optional equip-
ment is not used. (p. 4) t DEALER-PROGRAMMABLE KEY [Lower]
The desired function can be assigned by your dealer. (p. 9) y PTT SWITCH [PTT]
Push and hold to transmit; release to receive. u DEALER-PROGRAMMABLE KEY [Upper]
The desired function can be assigned by your dealer. (p. 9) i ANTENNA CONNECTOR Connects the supplied antenna. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 7 2 PANEL DESCRIPTION LED indicator The LED indicator indicates several information as follows;
(Ref.; R=Red, G=Green, O=Orange) TX: Turns Red while transmitting a signal. R RX: Turns Green while receiving a signal. G Fast/Slow scan: Blinks while Fast/Slow scan is activated. F/S Scan G G Low BATT1: You should charge the battery. (blinks slowly) Low BATT1 Low BATT2 Low BATT2: You must charge the battery. (blinks fast) G G G G G G TX low BATT2: Low BATT2 was detected during TX mode. TX Low BATT2 R R R R CH error: Non-programmed channel is selected. R O R O R O R O R O R O R O R O For IC-F3013/IC-F4013 only Call LED (ON): When receiving a matched 2/5-tone. Call LED ON O O Call LED (Blink): When receiving a matched 2/5-tone. Call LED Blink 8 O O PANEL DESCRIPTION 2 Programmable function keys The following functions can be assigned to [Upper] and [Lower]
programmable function keys. Consult your Icom dealer or system operator for details concerning your transceivers programming. D For All models SCAN A KEY Push to start and cancel scanning operation. When the Power ON scan function is turned ON, push to pause the scanning operation. The paused scan restarts after the spec-
ified time period has passed. SCAN B KEY Push to start and cancel scanning operation. In case of transmis-
sion during scan, pauses scanning. The paused scan restarts after the specified time period has passed. PRIORITY CHANNEL KEYS Push to select the Priority A or Priority B channel. Push and hold [Prio A (Rewrite)] to rewrite the Prio A channel. MR-CH 1/2/3/4 KEYS Push to select a memory channels 1 to 4 directly. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 9 2 PANEL DESCRIPTION OUTPUT POWER SELECTION KEY Select the transmit output power temporarily or permanently, de-
pending on the pre-setting. Ask your dealer for the output power level for each selection. TALK AROUND KEY Push to turn the talk around function OFF. Push and hold to turn the talk around function ON. The talk around function equalizes the transmit frequency to the receive frequency for transceiver-to-transceiver communication. WIDE/NARROW KEY Push to select the IF bandwidth to wide. The wide passband width can be selected from 25 or 20 kHz using the optional cloning software (PMR operation only). Ask your dealer for details. Push and hold to select the IF bandwidth to narrow. SIREN KEY Push to emit a siren. This function can be used for situations other than an emergency alert such as a security alarm for example. LOCK KEY Push and hold to electronically lock all programmable keys except the followings: [Moni(Audi)], [Call] (incl. Call A and Call B)* and
[Emergency Single]/[Emergency Repeat] (incl. Silent)*.
* Available for IC-F3013/IC-F4013 only. 10 PANEL DESCRIPTION 2 MONITOR KEY Push to mute and release the CTCSS (DTCS) or 2Tone* squelch mute. Open any squelches/deactivate any mutes while pushing this key. (LMR operation only)
* Available for the IC-F3013/F4013 only. Activates one of (or two of) the following functions on each chan-
nel independently: (PMR operation only) Push and hold to un-mute the channel (audio is emitted; Audible). Push to mute the channel (audio is not emitted; Inaudible). Push to send a reset code after the communication is finished. NOTE: The un-mute condition (Audible condition) may auto-
matically return to the mute condition (Inaudible condition) after a specified period. D For IC-F3013/IC-F4013 only DTMF AUTODIAL KEY Push to transmit the programmed DTMF code. CALL KEYS Push to transmit a 2/5-tone code. Call transmission is necessary before you call another station depend-
ing on your signalling system.
[Call A] and/or [Call B] keys may be available when your system em-
ploys selective Individual/Group calls. Ask your dealer which call is assigned to each key. EMERGENCY SINGLE/EMERGENCY REPEAT KEYS Push and hold for the specified time period to transmit an emer-
gency call once or repeatedly. When [Emergency Single (Silent)] or [Emergency Repeat (Silent)]
is pushed, an emergency call is transmitted with no beep emission. If you want to cancel the emergency call, push (or push and hold) the key again before transmitting the call. The emergency call is transmitted one time only or repeatedly until receiving a control code depending on the pre-setting. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 11 3 CONVENTIONAL OPERATION Turning power ON Rotate [VOL] to turn power ON.
[VOL]
[CHANNEL SELECTOR]
Channel selection Rotate [CHANNEL SELECTOR] to se-
lect the desired operating channel, in sequence; or, push one of [MR-CH 1] to
[MR-CH 4] key to select a channel di-
rectly. AUTOMATIC SCAN TYPE:
Channel setting is not necessary for this type. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call. 12 CONVENTIONAL OPERATION 3 Receiving and transmitting NOTE: Transmitting without an antenna may damage the trans-
ceiver. See p. 2 for antenna attachment. Receiving:
q Rotate [VOL] to turn power ON. w Rotate [CHANNEL SELECTOR] or push one of [MR-CH 1] to
[MR-CH 4] key to select a channel. e When receiving a call, adjust the audio output level to a comfort-
able listening level. Transmitting:
Wait for the channel to become clear to avoid interference. q While pushing and holding [PTT], speak into the microphone at a normal voice level. w Release [PTT] to return to receive. IMPORTANT: To maximize the readability of your signal;
1. Pause briefly after pushing [PTT]. 2. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak into the microphone at a normal voice level. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 13 3 CONVENTIONAL OPERATION D Transmitting notes Transmit inhibit function The transceiver has several inhibit functions which restrict trans-
mission under the following conditions:
- The channel is in mute condition.
- The channel is busy.
- Un-matched (or matched) CTCSS is received.
- The selected channel is a receive only channel. Time-out timer After continuous transmission for the pre-programmed time period, the time-out timer activates, and causes the transceiver to stop transmit-
ting. Penalty timer Once the time-out timer activates, transmission is further inhibited for a period determined by the penalty timer. 14 CONVENTIONAL OPERATION 3 Setting the squelch level The squelch circuit mutes the received audio signal depending on the signal strength.
[VOL]
q While pushing [PTT] and [Lower], rotate [VOL] to turn the power ON to enter the squelch level adjust-
ment mode. w Push [Upper] to increase the squelch level (tight squelch) or
[Lower] to decrease the squelch level (loose squelch). e Rotate [VOL] to turn the power OFF to fix the squelch level.
[Upper]
[PTT]
[Lower]
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 15 4 SIGNALING OPERATIONS NOTE: The tone signalling operations are available for the IC-F3013/F4013 only. Call procedure When your system employs tone signalling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice trans-
mission. The tone signalling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from contacting you. q Select the desired TX code channel or 2/5-tone code according to your System Operators instructions. This may not be necessary depending on programming. w Push [Call]. (p. 11) e After transmitting a 2/5-tone code, the remainder of your com-
munication can be carried out in the normal fashion. Selective calling Non-selective calling D Transmitting notes PTTID call The transceiver sends the ID code (5-tone, DTMF or digital ANI) automatically when [PTT] is pushed (beginning of transmission) and released (end of transmission) depends on the setting. 16 SIGNALING OPERATIONS 4 Emergency Call When [Emergency Single] or [Emergency Repeat] (p. 11) is pushed and held for the specified time period, the emergency sig-
nal (5-tone, DTMF or MDC 1200) is transmitted once or repeatedly on the emergency channel. A repeat emergency signal is auto-
matically transmitted until it receives the acknowledgement signal. When no emergency channel is specified, the signal is transmitted on the previously selected channel. If you want to cancel the emergency call, push and hold the key again before transmitting the call. The emergency call can be transmitted without a beep emission, and the LCD indication if [Emergency Single (Silent)] or [Emer-
gency Repeat (Silent)] (p. 11) is pushed. The transceiver can also be programmed to keep the microphone open during an emergency call, allowing monitoring of the situa-
tion. IMPORTANT: It is recommended to set an emergency channel individually to provide the certain emergency call operation. DTMF transmission If the transceiver has [DTMF Autodial] assigned to it, the auto-
matic DTMF transmission function is available. Push [DTMF Autodial] to transmit the DTMF code. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 17 5 BATTERY CHARGING Caution Misuse of Lithium-ion batteries may result in the following hazards: smoke, fire, or the battery may rupture. Misuse can also cause damage to the battery or degradation of battery performance. R DANGER! Use and charge only specified Icom battery packs with Icom radios or Icom charger. Only Icom battery packs are tested and approved for use and charge with Icom radios or Icom charger. Using third-party or counterfeit battery packs or charger may cause smoke, fire, or cause the battery to burst. D Battery caution R DANGER! DO NOT hammer or otherwise impact the battery. Do not use the battery if it has been severely impacted or dropped, or if the battery has been subjected to heavy pressure. Battery damage may not be visible on the outside of the case. Even if the surface of the battery does not show cracks or any other damage, the cells inside the battery may rupture or catch fire. R DANGER! NEVER use or leave battery packs in areas with temperatures above +60C (+140F). High temperature buildup in the battery, such as could occur near fires or stoves, inside a sun heated car, or in direct sunlight may cause the battery to rupture or catch fire. Excessive temperatures may also degrade battery per-
formance or shorten battery life. R DANGER! DO NOT expose the battery to rain, snow, seawater, or any other liquids. Do not charge or use a wet battery. If the bat-
tery gets wet, be sure to wipe it dry before using. The battery is not waterproof. 18 BATTERY CHARGING 5 R DANGER! NEVER incinerate used battery packs since internal battery gas may cause them to rupture, or may cause an explosion. R DANGER! NEVER solder the battery terminals or NEVER mod-
ify the battery pack. This may cause heat generation, and the bat-
tery may rupture, emit smoke or catch fire. R DANGER! Use the battery only with the transceiver for which it is specified. Never use a battery with any other equipment, or for any purpose that is not specified in this instruction manual. R DANGER! If fluid from inside the battery gets in your eyes, blind-
ness can result. Rinse your eyes with clean water, without rubbing them, and see a doctor immediately. WARNING! Immediately stop using the battery if it emits an ab-
normal odor, heats up, or is discolored or deformed. If any of these conditions occur, contact your Icom dealer or distributor. WARNING! Immediately wash, using clean water, any part of the body that comes into contact with fluid from inside the battery. WARNING! NEVER put the battery in a microwave oven, high-
pressure container, or in an induction heating cooker. This could cause a fire, overheating, or cause the battery to rupture. CAUTION! Always use the battery within the specified temperature range for the transceiver (30C to +60C; 22F to +140F) and the battery itself (20C to +60C; 4F to +140F). Using the bat-
tery out of its specified temperature range will reduce the batterys performance and battery life. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 19 5 BATTERY CHARGING CAUTION! Shorter battery life could occur if the battery is left fully charged, completely discharged, or in an excessive temperature environment (above +50C; +122F) for an extended period of time. If the battery must be left unused for a long time, it must be de-
tached from the radio after discharging. You may use the battery until the remaining capacity is about half, then keep it safely in a cool dry place with the temperature range as below:
20C to +50C (4F to +122F) 20C to +35C (4F to +95F) 20C to +20C (4F to +68F)
(within a month)
(within three months)
(within a year) D Charging caution R DANGER! NEVER charge the battery pack in areas with ex-
tremely high temperatures, such as near fires or stoves, inside a sun heated car, or in direct sunlight. In such environments, the safety/protection circuit in the battery will activate, causing the bat-
tery to stop charging. WARNING! DO NOT charge or leave the battery in the battery charger beyond the specified time for charging. If the battery is not completely charged by the specified time, stop charging and re-
move the battery from the battery charger. Continuing to charge the battery beyond the specified time limit may cause a fire, overheat-
ing, or the battery may rupture. WARNING! NEVER insert the transceiver (battery attached to the transceiver) into the charger if it is wet or soiled. This could corrode the battery charger terminals or damage the charger. The charger is not waterproof. CAUTION! DO NOT charge the battery outside of the specified temperature range: BC-160 (0C to +40C; +32F to +104F). Icom recommends charging the battery at +20C (+68F). The battery may heat up or rupture if charged out of the specified temperature range. Additionally, battery performance or battery life may be re-
duced. 20 BATTERY CHARGING 5 Battery chargers D Rapid charging with the BC-160 The optional BC-160 provides rapid charging of the Li-Ion battery pack. Charging period: Approx. 3 hours (with BP-232N) The following items are additionally required:
An AC adapter (not supplied with some versions) or the DC power cable (OPC-515L/CP-17L) is additionally required. AC adapter
(Not supplied with some versions.) Battery pack Transceiver Turn power OFF Optional OPC-515L
(for 13.8 V power source) or CP-17L
(for 12 V cigarette lighter socket) can be used instead of the AC adapter. Lobes IMPORTANT!
Ensure the guide lobes on the battery pack are correctly aligned with the guide rails inside the charger adapter. Guide rail 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 5 BATTERY CHARGING D Regular charging with the BC-171 The optional BC-171 provides regular charging of the Li-Ion battery pack. Charging period: Approx. 10 hours (with BP-232N) The following items are additionally required:
An AC adapter (not supplied with some versions) or the DC power cable (OPC-515L/CP-17L) is additionally required. AC adapter
(Not supplied with some versions.) Battery pack Transceiver Turn power OFF Optional OPC-515L
(for 13.8 V power source) or CP-17L
(for 12 V cigarette lighter socket) can be used instead of the AC adapter. Lobes IMPORTANT!
Ensure the guide lobes on the battery pack are correctly aligned with the guide rails inside the charger adapter. Guide rail 22 BATTERY CHARGING 5 D AD-106 installation The AD-106 charger adapter must be installed into the BC-119N or BC-121N before battery charging. Connect the AD-106 charger adapter and the BC-119N/BC-
121N as below, then install the AD-106 into the holder space of the BC-119N or BC-121N with the supplied screws. Connectors Desktop charger adapter Plugs Screws supplied with the charger adapter This illustration is described with the BC-119N. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 23 5 BATTERY CHARGING D Rapid charging with the BC-119N+AD-106 The optional BC-119N provides rapid charging of the Li-Ion battery pack. Charging period: Approx. 3 hours (with BP-232N) The following items are additionally required:
An AD-106 (purchase separately). An AC adapter (not supplied with some versions) or the DC power cable (OPC-515L/CP-17L). Transceiver Turn power OFF Battery pack AC adapter
(Not supplied with some versions.) AD-106 charger adapter is installed in BC-119N. Lobes Optional OPC-515L
(for 13.8 V power source) or CP-17L
(for 12 V cigarette lighter socket) can be used instead of the AC adapter. 24 IMPORTANT!
Ensure the guide lobes on the bat-
tery pack are correctly aligned with the guide rails inside the charger adapter. Guide rails BATTERY CHARGING D Rapid charging with the BC-121N+AD-106 The optional BC-121N allows up to 6 battery packs to be charged simultaneously. Charging period: Approx. 3 hours (with BP-232N) 5 The following items are additionally required. Six AD-106. An AC adapter (BC-157) or the DC power cable (OPC-656) Transceiver Turn power OFF Battery pack AD-106 charger adapters are installed in each slot. AC adapter
(Purchase separately) DC power cable
(OPC-656)
(Connect with the DC power supply;
13.8 V/at least 7 A) IMPORTANT!
Ensure the guide lobes on the bat-
tery pack are correctly aligned with the guide rails inside the charger adapter. Guide rails Lobes 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 25 6 BATTERY CASE Optional battery case (BP-240) When using the optional battery case, install 6 AAA (LR03) size alkaline batteries as illustrated at right. q Unhook the battery cover release hook (q), and open the cover in the direction of the arrow (w). (Fig.1) Install the alkaline batteries only. Be sure to observe the correct polarity. Do not pin the ribbon under the batteries. w Then, install 6 AAA (LR03) size alkaline batteries. (Fig.2) e Fit the cover in the direction of the arrow (e), then close (r). Hook the battery cover release hook until it makes a click sound
(t). (Fig.3) CAUTION:
When installing batteries, make sure they are all the same brand, type and capacity. Also, do not mix new and old batter-
ies together. Keep battery contacts clean. Its a good idea to clean battery terminals once a week. Never incinerate used battery cells since internal battery gas may cause them to rupture. Never expose a detached battery case to water. If the battery case gets wet, be sure to wipe it dry before using it. NOTE: When the optional battery case is attached, the battery type must be selected to Alkaline battery operation when turn-
ing the transceiver ON. Ask your dealer for details. 26 Fig.1 Fig.2 Fig.3 BATTERY CASE 6 w BP-240 q e r t 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 27 7 SWIVEL BELT CLIP MB-93 contents Qty. q Belt clip .................................................................................... 1 w Base clip .................................................................................. 1 q w To attach q Release the battery pack if it is attached. (p. 3) w Slide the base clip in the direction of the arrow until the base clip is locked and makes a click sound. 28 7 e Clip the belt clip to a part of your belt. And insert the transceiver into the belt clip until the base clip inserted fully into the groove. SWIVEL BELT CLIP r Once the transceiver is locked in place, it swivels as illustrated below. Once the transceiver is locked in place, it will swivel 360 degrees. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 29 7 SWIVEL BELT CLIP To detach q Turn the transceiver upside down in the direction of the arrow and pull out from the belt clip. 30 SWIVEL BELT CLIP 7 w Release the battery pack if it is attached. (p. 3) e Pinch the clip (q), and slide the base clip in the direction of the arrow (w). q w CAUTION:
HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR DETACHING THE TRANSCEIVER FROM THE BELT CLIP. Otherwise the transceiver may not be attached to the holder or swivel properly if the transceiver is accidentally dropped and the base clip is scratched or damaged. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 31 8 OPTIONS D BATTERY PACK Battery pack Voltage Capacity Battery life*1 BP-230N 7.4 V BP-232N 7.4 V 950 mAh (min.) 980 mAh (typ.) 1900 mAh (min.) 2000 mAh (typ.) BP-240 Battery case for AAA
(LR03) 6 alkaline 9 hrs. 18 hrs.
*2
*1 When the power save function is turned ON, and the operating pe-
riods are calculated under the following conditions;
TX : RX : standby = 5 : 5 : 90
*2 Operating period depends on the alkaline cells used. D CHARGERS BC-119N desktop charger + AD-106 charger adapter
+ BC-145S ac adapter For rapid charging of battery packs. An AC adapter is supplied with the charger depending on versions. Charging time: approx. 3 hours when BP-232N is attached. BC-121N multi-charger + AD-106 charger adapter (6 pcs.)
+ BC-157 ac adapter For rapid charging of up to 6 battery packs (six AD-106s are required) simultaneously. An AC adapter should be purchased separately. Charging time: approx. 3 hours when BP-232N is attached. BC-160 desktop charger + BC-145S ac adapter For rapid charging of battery packs. An AC adapter is supplied with the charger depending on versions. Charging time: approx. 3 hours when BP-232N is attached. 32 OPTIONS 8 BC-171 desktop charger + BC-147S ac adapter For regular charging of battery packs. We recommend that the BP-230N charging. An AC adapter is supplied with the charger depending on versions. Charging time: Approx. 10 hours when BP-232N is attached. Approx. 4 hours when BP-230N is attached. D BELT CLIPS MB-93 swivel belt clip MB-94 belt clip Exclusive alligator-type belt clip. MB-96N/96F leather belt hanger D DC CABLES CP-17L cigarette lighter cable Allows charging of the battery pack through a 12 V cigarette lighter socket. (For BC-119N) OPC-515L/OPC-656 dc power cables Allows charging of the battery pack using a 13.8 V power source instead of the AC adapter. OPC-515L: For BC-119N OPC-656 : For BC-121N D ANTENNAS FA-SC73US/FA-SC56VS/FA-SC57VS stubby antennas FA-SC73US: 450490 MHz FA-SC57VS: 160174 MHz FA-SC01U/FA-SC25U/FA-SC57U/FA-SC72U/FA-SC25V/
FA-SC56VS: 150162 MHz FA-SC55V antennas FA-SC01U: 350400 MHz FA-SC57U: 430470 MHz FA-SC25V: 136155 MHz FA-SC61VC/FA-SC61UC cut antennas FA-SC61VC: 136174 MHz FA-SC25U: 400430 MHz FA-SC72U: 470520 MHz FA-SC55V: 146174 MHz FA-SC61UC: 380520 MHz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 33 8 OPTIONS D OTHER OPTIONS SP-13 earphone Provides clear receive audio in noisy environment. HM-153L earphone-microphone HM-131L/158L/159L speaker-microphone Combination speaker-microphone that provides convenient op-
eration while hanging the transceiver from your belt. VS-1L vox/ptt case + HS-94/HS-95/HS-97 headset VS-1L: VOX/PTT switch box for hands-free operation, etc. HS-94: Ear hook type HS-97: Throat microphone HS-95: Neck-arm type Icom optional equipment are designed for optimal performance when used with this transceiver. We are not responsible for the transceiver being damaged or any accident caused when using non-Icom optional equipment. Some options may not be available in some countries. Please ask your dealer for details. 34 OPTIONS 8 D About VS-1L vox/ptt case The VS-1L is a VOX/PTT unit for Icom handheld transceivers, and allows you hands-free operation. An optional headset (HS-94, etc.) is additionally required for opera-
tion. The VOX (voice operated transmission) function starts transmission without pushing PTT switch when you speak into the microphone;
then, automatically returns to receive when you stop speaking. Features Straight type head SP/MIC plug equipped Water resistant construction Durable construction Equipped with a PTT switch and revolving clip. MIC/VOX gain adjustment 1 Remove the water protection cover on the right side of the VS-1L. 2 Adjust the MIC/VOX gain with a thin screw driver. Clockwise rota-
tion increases the MIC/VOX gain. 3 Return the protective cover back to the MIC/VOX gain adjustment hole. Adjusting pot VS-1L PTT switch Water protection cover VOX PTT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 35 9 FCC INFORMATION FOR CLASS B UNINTENTIONAL RADIATORS:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 36 MEMO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 MEMO MEMO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 MEMO MEMO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 A-6768H-1EX-q Printed in Japan 2009 Icom Inc. Printed on recycled paper with soy ink. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
1 2 3 | Users Manual | Users Manual | 841.23 KiB |
!IC-F14_F24.qxd 04.6.17 6:22 PM Page A (1,1) INSTRUCTION MANUAL VHF TRANSCEIVER iF14/S UHF TRANSCEIVER iF24/S This device complies with Part 15 of the FCC rules. Operation is subject to the condition that this device does not cause harmful interfer-
ence.
!IC-F14_F24.qxd 04.6.17 6:22 PM Page i (1,1) SAFETY TRAINING INFORMATION Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and clas-
sified as Occupational Use Only, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such haz-
ards. This radio is NOT intended for use by the General Population in an uncontrolled environment. W ARNING This radio has been tested and complies with the FCC RF exposure lim-
its for Occupational Use Only. In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans:
FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Com-
pliance with FCC Guidelines for Human Exposure to Radio Fre-
quency Electromagnetic Fields. American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Fre-
quency Electromagnetic Fields, 3 kHz to 300 GHz. American National Standards Institute (C95.3-1992), IEEE Recom-
mended Practice for the Measurement of Potentially Hazardous Elec-
tromagnetic Fields RF and Microwave. The following accessories are authorized for use with this product. Use of accessories other than those specied may result in RF ex-
posure levels exceeding the FCC requirements for wireless RF ex-
posure.; Belt Clip (MB-94), Rechargeable Li-Ion Battery Pack
(BP-231) and Speaker-microphone (HM-131L). To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occupa-
tional use, always adhere to the following guidelines:
CAU TION i DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specically authorized by the manufacturer for use with this radio. DO NOT transmit for more than 50% of total radio use time (50%
duty cycle). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the Transmit indicator lights red. You can cause the radio to transmit by pressing the PTT switch. ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the Icom belt-clip which is listed on page 33 when attaching the radio to your belt, etc., to ensure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound quality, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to as-
sure that this radio operates with the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can pos-
sibly cause interference with other devices or systems. To avoid such in-
terference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electro-
magnetic radiation such as hospitals, aircraft, and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. ii
!IC-F14_F24.qxd 04.6.17 6:22 PM Page iii (1,1) FOREWORD READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL This instruction manual contains important operating instructions for the IC-F14/
F14S VHF TRANSCEIVER and IC-F24/F24S UHF TRANSCEIVER. EXPLICIT DEFINITIONS WORD DEFINITION RWARNING Personal injury, fire hazard or electric shock may occur. CAUTION NOTE Equipment damage may occur. If disregarded, inconvenience only. No risk of personal injury, fire or electric shock. OPERATING NOTES When transmitting with a portable radio, hold the radio in a vertical position with its microphone 5 to 10 centimeters (2 to 4 inches) away from your mouth. Keep the antenna at least 2.5 centimeters
(1 inch) from your head and body. If you wear a portable two-way radio on your body, ensure that the antenna is at least 2.5 centimeters (1 inch) from your body when transmitting. iii PRECAUTION R WARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 inches) away from the lips and the transceiver is vertical. R WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. CAUTION! NEVER short the terminals of the battery pack. NEVER connect the transceiver to a power source other than the BP-230, BP-231 or BP-232. Such a connection will ruin the trans-
ceiver. DO NOT push the PTT when not actually desiring to transmit. AVOID using or placing the transceiver in direct sunlight or in areas with temperatures below 22F (30C) or above +140F
(+60C). DO NOT modify the transceiver for any reason. MAKE SURE the exible antenna and battery pack are securely attached to the transceiver, and that the antenna and battery pack are dry before attachment. Exposing the inside of the transceiver to water will result in serious damage to the transceiver. The use of non-Icom battery packs/chargers may impair transceiver performance and invalidate the warranty. FCC caution:
Changes or modications to this device, not expressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations. Icom, Icom Inc. and the logo are registered trademarks of Icom Incorpo-
rated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. iv
!IC-F14_F24.qxd 04.6.17 6:22 PM Page v (1,1) ACCESSORIES 1 TABLE OF CONTENTS SAFETY TRAINING INFORMATION i FOREWORD iii EXPLICIT DEFINITIONS iii OPERATING NOTES iii PRECAUTION iv TABLE OF CONTENTS v 1 ACCESSORIES 15 Supplied accessories 1 Accessory attachments 2 2 PANEL DESCRIPTION 611 Front, top and side panels 6 LED indicator 8 Programmable function keys 9 3 CONVENTIONAL OPERATION 1218 Turning power ON 12 Channel selection 12 Call procedure 13 Receiving and transmitting 14 Scrambler function 16 Setting the squelch level 16 Man Down Emergency Call 17 4 OPTIONAL UNIT INSTALLATION 1819 Optional unit installation 18 Scrambler unit installation 19 5 BATTERY CHARGING 2025 Battery charging 20 Caution 21 Optional battery chargers 22 6 SWIVEL BELT CLIP 2629 MB-93 contents 26 To attach 26 To detach 28 7 SPEAKER-MICROPHONE 3031 Optional HM-75A description 30 To attach 31 8 OPTIONS 3233 v I Supplied accessories The following accessories are supplied:
Qty. q Flexible antenna . 1 w Battery pack . 1 e Belt clip . 1 r Jack cover (with screws) . 1 set q w e r 1 1
!IC-F14_F24.qxd 04.6.17 6:22 PM Page 2 (1,1) 1 ACCESSORIES I Accessory attachments D Flexible antenna Connect the supplied flexible an-
tenna to the antenna connector. CAUTION:
NEVER HOLD by the antenna when carrying the transceiver. Transmitting without an antenna may damage the transceiver. ACCESSORIES 1 1 Battery pack To attach the battery pack:
Slide the battery pack on the back of the transceiver in the direc-
tion of the arrow (q), then lock it with the battery release button. Slide the battery pack until the battery release button makes a click sound. To release the battery pack:
Push the battery release button in the direction of the arrow (w) as shown below. The battery pack is then released. NEVER release or attach the battery pack when the transceiver is wet or soiled. This may result in water or dust getting into the transceiver/battery pack and may result in the transceiver being damaged. q w 2 3
!IC-F14_F24.qxd 04.6.17 6:22 PM Page 4 (1,1) 1 ACCESSORIES Jack cover Attach the jack cover when the optional speaker-microphone is not used. To attach the jack cover:
q Attach the jack cover to the To detach the jack cover:
q Unscrew the screws with a
[SP MIC] connector. w Tighten the screws. phillips screwdriver. w Detach the jack cover for the speaker-microphone connec-
tion. ACCESSORIES 1 D Belt clip To attach the belt clip:
q Release the battery pack if it is attached. w Slide the belt clip in the direction of the arrow until the belt clip is 1 locked and makes a click sound. q w w w q q To detach the belt clip:
q Release the battery pack if it is attached. w Pinch the clip (q), and slide the belt clip in the direction of the arrow (w). w q 4 5
!IC-F14_F24.qxd 04.6.17 6:22 PM Page 6 (1,1) 2 PANEL DESCRIPTION I Front, top and side panels q IC-F14S/F24S IC-F14/F24 i u y t w e Speaker r Microphone q CHANNEL SW/SELECTOR IC-F14S/F24S: Toggle the channel switch to select the pre-pro-
IC-F14/F24 grammed channel 1 or 2.
: Rotate the channel selector to select the pre-
programmed memory channels. w VOLUME CONTROL [VOL]
Rotate to turn the power ON/OFF and adjust the audio level. 6 PANEL DESCRIPTION 2 e LED INDICATOR (p. 8) Lights red while transmitting. Lights green while receiving a signal, or when the squelch is open. Lights/blinks orange when the matched 2/5-tone code is re-
ceived, according to the pre-programming. r SPEAKER-MICROPHONE CONNECTOR [SP MIC]
Connects the optional speaker-microphone. (p. 31)
[SP MIC] jack cover NOTE: Attach the [SP MIC] jack cover when the optional speak-
er-microphone is not used. (p. 4) t DEALER-PROGRAMMABLE KEY [Lower]
The desired function can be assigned by your dealer. (p. 9) y PTT SWITCH [PTT]
Push and hold to transmit; release to receive. u DEALER-PROGRAMMABLE KEY [Upper]
The desired function can be assigned by your dealer. (p. 9) i ANTENNA CONNECTOR Connects the supplied antenna. DD Programmable key reference Upper Mic Up*
Mic A*
Lower Mic Down*
Mic B*
*These functions are available when the optional Speaker-Microphone is connected. (p. 31) 2 7
!IC-F14_F24.qxd 04.6.17 6:22 PM Page 8 (1,1) 2 PANEL DESCRIPTION LED indicator The LED indicator indicates several informa-
tion as follows;
(Ref.; R=Red, G=Green, O=Orange) TX: Turns Red while transmitting a signal. R RX: Turns Green while receiving a signal. G Call LED (ON): When receiving a matched 2/5-tone. O O Call LED (Blink): When receiving a matched 2/5-tone. O O Fast/Slow scan: Blinks while Fast/Slow scan is activated. G G Low BATT1: You should charge the battery. (blinks slowly) R R Low BATT2: You must charge the battery. (blinks fast) R R R R TX low BATT1: Low BATT1 was detected during TX mode. R R TX low BATT2: Low BATT2 was detected during TX mode. R R R R 8 PANEL DESCRIPTION 2 I Programmable function keys The following functions can be assigned to [Upper], [Lower], [Mic Up]*, [Mic Down]*, [Mic A]* and [Mic B]* programmable function keys. Consult your Icom dealer or system operator for details concerning your transceivers programming. If the programmable function names are bracketed in the following explanations, the specic key used to activate the function depends on programming.
*These keys are available when the optional Speaker-Microphone is connected. (p. 31) SCAN A KEY This keys operation depends on the Power ON Scan setting. When the power ON scan function is turned OFF;
Push to start and cancel scanning operation. In case of trans-
mission during scan, cancels scanning. When the power ON scan function is turned ON;
Push to pause scanning. Scanning resumes after passing a specified time period. In case of transmission during scan, pauses scanning. Scanning resumes after passing a specied time period. SCAN B KEY Push to start and cancel scanning operation. In case of transmis-
sion during scan, pauses scanning. Scanning resumes after pass-
ing a specied time period. PRIORITY CHANNEL KEYS Push to select the Priority A or Priority B channel. Push and hold [Prio A (Rewrite)] to rewrite the Prio A channel. MR-CH 1/2/3/4 KEYS Push to select a memory channels 1 to 4 directly. NOTE: The memory channels 3 and 4 are available for IC-
F14S/F24S when [MR-CH 3] and [MR-CH 4] keys are assigned. 2 9
!IC-F14_F24.qxd 04.6.17 6:22 PM Page 10 (1,1) 2 PANEL DESCRIPTION MONITOR KEY Mute and release the CTCSS (DTCS) or 2-tone squelch mute. Open any squelch/deactivate any mute while pushing this key.
(LMR operation only) Activates one of (or two of) the following functions on each chan-
nel independently: (PMR operation only) Push and hold to un-mute the channel (audio is emitted; Audible condition). Push to mute the channel (sets to Inaudible only). Push to un-mute the channel (sets to Audible only). Push after the communication is nished to send a reset code. NOTE: The un-mute condition (Audible condition) may auto-
matically return to the mute condition (Inaudible condition) after a specied period. LOCK KEY Push and hold to electronically lock all programmable keys except the following:
[Call] (incl. Call A and Call B), [Moni(Audi)] and [Emergency] keys. OUTPUT POWER SELECTION KEY Select the transmit output power temporarily or permanently, de-
pending on the pre-setting. Ask your dealer for the output power level for each selection. TALK AROUND KEY Turn the talk around function ON and OFF. The talk around function equalizes the transmit frequency to the re-
ceive frequency for transceiver-to-transceiver communication. WIDE/NARROW KEY Push to select the IF bandwidth to wide. Push and hold to select the IF bandwidth to narrow. The wide passband width can be selected from 25.0 or 20.0 kHz using the CS-F14 CLONING SOFTWARE. (PMR operation only) Ask your dealer for details. 10 PANEL DESCRIPTION 2 DTMF AUTODIAL KEY Push to transmit the programmed DTMF code. CALL KEYS Push to transmit a 2/5-tone code. Call transmission is necessary before you call another station de-
pending on your signalling system.
[Call A] and/or [Call B] keys may be available when your system em-
ploys selective Individual/Group calls. Ask your dealer which call is assigned to each key. EMERGENCY KEYS Push and hold to transmit an emergency call. When [Emergency Single (Silent)] or [Emergency Repeat
(Silent)] is pushed, an emergency call is transmitted without a beep emission. If you want to cancel the emergency call, push (or push and hold) the key again before transmitting the call. The emergency call is transmitted one time only or repeatedly until receiving a control code depending on the pre-setting. VOICE SCRAMBLER FUNCTION KEYS Push to turn the voice scrambler function OFF. Push and hold to turn the voice scrambler function ON. OPT OUT KEYS Push to inactivate the connected output signal level. Push and hold to activate the connected output signal level. SIREN KEY Push to emit a siren. This function can be used for situations other than an emergency alert such as a security alarm for example. 2 11
!IC-F14_F24.qxd 04.6.17 6:22 PM Page 12 (1,1) 3 CONVENTIONAL OPERATION I Turning power ON Rotate [VOL] to turn power ON.
[VOL]
I Channel selection IC-F14S/F24S:
Toggle [CHANNEL SWITCH] to select the channel 1 or 2, or, push one of [MR-
CH 1] to [MR-CH 4] key to select a chan-
nel directly. The memory channels 3 and 4 are avail-
able when [MR-CH 3] and [MR-CH 4]
keys are assigned. IC-F14/F24:
Rotate [CHANNEL SELECTOR] to se-
lect the desired operating channel, in se-
quence; or, push one of [MR-CH 1] to
[MR-CH 4] key to select a channel di-
rectly.
[CHANNEL SWITCH]
[CHANNEL SELECTOR]
AUTOMATIC SCAN TYPE:
Channel setting is not necessary for this type. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call. 12 CONVENTIONAL OPERATION 3 I Call procedure When your system employs tone signalling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice trans-
mission. The tone signalling employed may be a selective calling system which allows you to call specic station(s) only and prevent unwanted stations from contacting you. 3 q Select the desired TX code channel or 2/5-tone code according to your System Operators instructions. This may not be necessary depending on programming. w Push the call key (assigned to one of the dealer programmable keys). (p. 9) e After transmitting a 2/5-tone code, the remainder of your com-
munication can be carried out in the normal fashion. Selective calling Non-selective calling 13
!IC-F14_F24.qxd 04.6.17 6:22 PM Page 14 (1,1) 3 CONVENTIONAL OPERATION I Receiving and transmitting NOTE: Transmitting without an antenna may damage the trans-
ceiver. See p. 2 for antenna attachment. Receiving:
q Rotate [VOL] to turn power ON. w Toggle [CHANNEL SWITCH] (IC-F14S/F24S), rotate [CHAN-
NEL SELECTOR] (IC-F14/F24) or push one of [MR-CH 1] to
[MR-CH 4] key to select a channel. For IC-F14S/F24S:
The memory channels 3 and 4 are available when [MR-CH 3]
and [MR-CH 4] keys are assigned. e When receiving a call, adjust the audio output level to a comfort-
able listening level. Transmitting:
Wait for the channel to become clear to avoid interference. q While pushing and holding [PTT], speak into the microphone at a normal voice level. When a tone signalling system is used, the call procedure de-
scribed on p. 13 may be necessary. w Release [PTT] to return to receive. IMPORTANT!: To maximize the readability of your signal;
1. Pause briey after pushing [PTT]. 2. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak into the microphone at a normal voice level. CONVENTIONAL OPERATION 3 D Transmitting notes Transmit inhibit function The transceiver has several inhibit functions which restrict trans-
mission under the following conditions:
3
- The channel is in mute condition.
- Channel is busy.
- Un-matched (or matched) CTCSS is received.
- The selected channel is a receive only channel. Time-out timer After continuous transmission for the pre-programmed time period, the time-out timer activates, and causes the transceiver to stop transmit-
ting. Penalty timer Once the time-out timer activates, transmission is further inhibited for a period determined by the penalty timer. D DTMF transmission If the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is available. Push [DTMF Autodial] to transmit the DTMF code. 14 15
!IC-F14_F24.qxd 04.6.17 6:22 PM Page 16 (1,1) 3 CONVENTIONAL OPERATION I Scrambler function The optional voice scrambler units UT-109 (#01) and UT-110 (#01) provide high performance private communication between stations with the same scrambler codes. Push and hold [Scrambler] to turn the scrambler function ON. Push [Scrambler] to turn the scrambler function OFF. I Setting the squelch level The squelch circuit mutes the received audio signal depending on the signal strength. CONVENTIONAL OPERATION 3 I Man Down Emergency Call The man down emergency call function transmits an emergency call automatically, after the transceiver laying down in a horizontal position for a pre-set time period. (The optional UT-113 MAN DOWN UNIT is required.) 3 After the emergency call, the transceiver performs transmission and reception alternately with the following conditions:
- Transmits the microphone signals.
- Receives the signal and emits audio. When the emergency cancel code is received, the function is can-
celled.
[VOL]
IMPORTANT!: Set an emergency channel individually, to provide certain emergency call operation is recommended. q While pushing [PTT] and [Lower], rotate [VOL] to turn the power ON to enter the squelch level adjust-
ment mode. w Push [Upper]
to increase the squelch level (tight squelch) or
[Lower] to decrease the squelch level (loose squelch). e Rotate [VOL] to turn the power OFF to x the squelch level.
[Upper]
[PTT]
[Lower]
16 17
!IC-F14_F24.qxd 04.6.17 6:22 PM Page 18 (1,1) 4 OPTIONAL UNIT INSTALLATION I Optional unit installation Install the optional unit as follows:
q Rotate [VOL] to turn the power OFF, and remove the battery pack. (p. 3) w Remove the unit cover. OPTIONAL UNIT INSTALLATION 4 I Scrambler unit installation The following PC board modication is required when installing the optional UT-109 or UT-110. q Rotate [VOL] to turn the power OFF, and remove the battery pack. (p. 3) NOTE: Use a flat head screw driver or a similar flat instru-
ment, and insert into the hollow of the chassis, then lift and take away the unit cover. (The removed cover cannot be used again.) w Remove the unit cover as shown at left (Optional unit installation.) e Cut the pattern on the PCB at the TX mic circuit (MIC) and RX AF circuit (DISC) as shown below. r Install the scrambler unit as shown at left (Optional unit installa-
tion.) t Replace the unit cover and the battery pack, then rotate [VOL] to turn the power ON. e Install the unit as shown below.
*This illustration is described with the UT-110. r Replace the unit cover and the battery pack, then rotate [VOL] to turn the power ON. NOTE: The optional UT-109/UT-110 SCRAMBLER UNITS requires some PC board modications. Please refer to the additional in-
stallation as at right. 18 NOTE: When uninstalling the scrambler unit Be sure to re-solder the discon-
nected points at left, otherwise no TX modulation or AF output is available. 4 19
!IC-F14_F24.qxd 04.6.17 6:22 PM Page 20 (1,1) 5 BATTERY CHARGING I Battery charging Prior to using the transceiver for the rst time, the battery pack must be fully charged for optimum life and operation. CAUTION: To avoid damage to the transceiver, turn it OFF while charging. Recommended temperature range for charging:
+10C to +40C (+50F to +104F)
- The Li-Ion battery functions within 20C to +60C (4F to
+140F) Use the specified chargers (BC-119N, BC-121N and BC-160). NEVER use another manufacturers charger. Use the optional AC adapter. NEVER use another manufacturers AC adapter. Recommendation:
Charge the supplied battery pack for a maximum of up to 10 hours. Li-Ion batteries are different from Ni-Cd batteries in that it is not necessary to completely charge and discharge them to prolong the battery life. Therefore, charging the battery in in-
tervals, and not for extended periods is recommended. 20 BATTERY CHARGING 5 I Caution R DANGER Charge the specied Icom batteries only. Only tested and approved for use with genuine Icom batteries. Fire and/or explosion may occur when a third party battery pack or counterfeit product is charged. CAUTION! NEVER insert battery pack/transceiver (with the bat-
tery pack attached) with wet or soiled into the charger. This may re-
sult in corrosion of the charger terminals or damage to the charger. The charger is not waterproof and water can easily get into it. NEVER incinerate used battery packs. Internal battery gas may cause an explosion. NEVER immerse the battery pack in water. If the battery pack be-
comes wet, be sure to wipe it dry immediately (particularly the bat-
tery terminals) BEFORE attaching it to the transceiver. Otherwise, the terminals will become corroded, or cause connection failure, etc. NEVER short the terminals of the battery pack. Also, current may ow into nearby metal objects, such as a necklace, etc. Therefore, be careful when carrying with, or placing near metal objects, carry-
ing in handbags, etc. AVOID leaving the battery pack in a fully charged, or completely discharged condition for long time. It causes shorter battery life. In case of leaving the battery pack unused for a long time, it must be kept safely after discharge, or use the battery until the battery indi-
cator appears, then remove it from the transceiver. If your battery pack seems to have no capacity even after being charged, fully charge the battery pack again. If the battery pack still does not retain a charge (or very little), a new battery pack must be purchased. 5 21
!IC-F14_F24.qxd 04.6.17 6:22 PM Page 22 (1,1) 5 BATTERY CHARGING I Optional battery chargers D Rapid charging with the BC-160 The optional BC-160 provides rapid charging of optional Li-Ion bat-
tery packs. An AC adapter (may be supplied with BC-160 depending on ver-
sion) or the DC power cable (OPC-515L/CP-17L) is additionally required. AC adapter
(Not supplied with some versions.) BP-231 TRANSCEIVER BATTERY CHARGING 5 AD-106 installation q Install the AD-106 desktop charger adapter into the holder space of the BC-119N/121N. Desktop charger adapter Connectors 5 Plugs w Connect the plugs of the BC-119N/BC-121N to the AD-106 with the connector, then install the adapter into the charger with the supplied screws. Screws supplied with the charger adapter Optional OPC-515L
(for 13.8 V power source) or CP-17L
(for 12 V cigarette lighter socket) can be used instead of the AC adapter. IMPORTANT!:
Ensure the guide lobs on the battery pack are correctly aligned with the guide rails inside the charger adapter. Guide rail Lobs 0
- 1 6 c b 22 23
!IC-F14_F24.qxd 04.6.17 6:22 PM Page 24 (1,1) 5 BATTERY CHARGING D Rapid charging with the BC-119N+AD-106 The optional BC-119N provides rapid charging of optional Li-Ion battery packs. The following items are additionally required:
One AD-106 (purchase separately). An AC adapter (may be supplied with BC-119N depending on ver-
sion) or the DC power cable (OPC-515L/CP-17L). TRANSCEIVER BP-231 AC adapter
(Not supplied with some versions.) BATTERY CHARGING D Rapid charging with the BC-121N+AD-106 The optional BC-121N allows up to 6 battery packs to be charged simultaneously. The following items are additionally required. Six AD-106. An AC adapter (BC-124) or the DC power cable (OPC-656) 5 TRANSCEIVER 5 BP-231 AD-106 charger adapters are installed in each slot. AC adapter
(Purchase separately) AD-106 charger adapter is installed in BC-119N. Lobs Optional OPC-515L
(for 13.8 V power source) or CP-17L
(for 12 V cigarette lighter socket) can be used instead of the AC adapter. 24 IMPORTANT!:
Ensure the guide lobs on the battery pack are correctly aligned with the guide rails inside the charger adapter. Guide rails DC power cable
(OPC-656)
(Connect with the DC power supply;
13.8 V/at least 7 A) IMPORTANT!:
Ensure the guide lobs on the battery pack are correctly aligned with the guide rails inside the charger adapter. Guide rails Lobs 25
!IC-F14_F24.qxd 04.6.17 6:22 PM Page 26 (1,1) 6 SWIVEL BELT CLIP I MB-93 contents Qty. q Belt clip 1 w Base clip 1 q w 6 e Clip the belt clip to a part of your belt. And insert the transceiver into the belt clip until the base clip inserted fully into the groove. SWIVEL BELT CLIP I To attach q Release the battery pack if it is attached. (p. 3) w Slide the base clip in the direction of the arrow until the base clip is locked and makes a click sound. r Once the transceiver is locked in place, it swivels as illustrated below. 26 6 27
!IC-F14_F24.qxd 04.6.17 6:22 PM Page 28 (1,1) 6 SWIVEL BELT CLIP I To detach q Turn the transceiver upside down in the direction of the arrow and pull out from the belt clip. SWIVEL BELT CLIP 6 w Release the battery pack if it is attached. (p. 3) e Pinch the clip (q), and slide the base clip in the direction of the arrow (w). q w CAUTION:
HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR DETACHING THE TRANSCEIVER FROM THE BELT CLIP. Otherwise the transceiver may not be attached to the holder or swivel properly if the transceiver is accidentally dropped and the base clip is scratched or damaged. 28 6 29
!IC-F14_F24.qxd 04.6.17 6:22 PM Page 30 (1,1) 7 SPEAKER-MICROPHONE I Optional HM-75A description
[Mic A]/[Mic B] keys*
PTT switch A B
[Mic Up]/[Mic Down] keys*
Rear OFF ON LOCK Lock switch:
Locks all keys except [PTT].
*The desired function can be assigned independently by your dealer. (p. 9) Earphone jack 30 SPEAKER-MICROPHONE 7 I To attach Attach the connector of the speaker-microphone into the [SP MIC]
connector on the transceiver and tighten the screw. CAUTION: When connecting the speaker-microphone to the transceiver, make sure that power to the transceiver is turned OFF, otherwise the CPU may malfunction. To [SP MIC] connector CAUTION: Attach the speaker-
microphone s connector securely to prevent accidental dropping, or water intrusion in the connector. IMPORTANT!: KEEP the [SP MIC] jack cover attached (trans-
ceiver) when the speaker-microphone is not in use (p. 4). Water will not get into the transceiver even if the cover is not attached, however, the terminals (pins) will become rusty, or the trans-
ceiver will function abnormally if the connector becomes wet. 7 31
!IC-F14_F24.qxd 04.6.17 6:22 PM Page 32 (1,1) 8 OPTIONS D BATTERY PACK BP-230 Li-Ion BATTERY PACK 7.4 V/800 mAh Li-Ion battery pack, allows approx. 5.5 hours* op-
eration. BP-231 Li-Ion BATTERY PACK 7.4 V/1150 mAh Li-Ion battery pack, allows approx. 8 hours* op-
eration. The same as supplied with the transceiver. BP-232 Li-Ion BATTERY PACK 7.4 V/2000 mAh Li-Ion battery pack, allows approx. 14 hours* op-
eration.
*Typical operation; Tx:Rx:Stand-by duty cycle=5:5:90 D CHARGERS BC-119N DESKTOP CHARGER + AD-106 CHARGER ADAPTER
+ BC-145 AC ADAPTER For rapid charging of battery packs. An AC adapter is supplied with the charger depending on versions. Charging time: approx. 2 hours when BP-231 is attached. BC-121N MULTI-CHARGER + AD-106 CHARGER ADAPTER (6 pcs.)
+ BC-124 AC ADAPTER For rapid charging of up to 6 battery packs (six AD-106s are re-
quired) simultaneously. An AC adapter should be purchased sep-
arately. Charging time: approx. 2 hours when BP-231 is attached. BC-160 DESKTOP CHARGER + BC-145 AC ADAPTER For rapid charging of battery packs. An AC adapter is supplied with the charger depending on versions. Charging time: approx. 2 hours when BP-231 is attached. D OPTIONAL UNITS UT-108 DTMF DECODER UNIT Provides pager and code squelch capabilities. UT-109 (#01)/UT-110 (#01) SCRAMBLER UNITS Non-rolling type (UT-109)/Rolling type (UT-110) voice scrambler unit provides higher communication security. UT-113 MAN DOWN UNIT Provides a measure of safety when working in a hazardous envi-
ronment, etc. 32 OPTIONS 8 Exclusive alligator-type belt clip. The same as supplied with the transceiver. D BELT CLIPS MB-93 SWIVEL BELT CLIP MB-94 BELT CLIP MB-96*/96F LEATHER BELT HANGER
*MB-93s base clip is required. D DC CABLES CP-17L CIGARETTE LIGHTER CABLE Allows charging of the battery pack through a 12 V cigarette lighter socket. (For BC-119N) OPC-515L/OPC-656 DC POWER CABLES Allows charging of the battery pack using a 13.8 V power source instead of the AC adapter. OPC-515L: For BC-119N OPC-656 : For BC-121N D OTHER OPTIONS SP-13 EARPHONE Provides clear receive audio in noisy environment. HM-75A/HM-131L SPEAKER-MICROPHONE Combination speaker-microphone that provides convenient oper-
ation while hanging the transceiver from your belt. HM-75A has the programmable function keys, Mic Up, Mic Down, Mic A and Mic B. HM-131L has a moisture proof construction. HS-94/HS-95/HS-97 HEADSET + VS-1L VOX/PTT CASE HS-94: Ear hook type HS-97: Throat microphone VS-1L: VOX/PTT switch box for hands-free operation, etc. FA-SC73US/FA-SC56VS/FA-SC57VS STUBBY ANTENNAS FA-SC73US: 450490 MHz FA-SC57VS: 160174 MHz FA-SC25U/FA-SC57U/FA-SC72U/FA-SC25V/FA-SC55V ANTENNAS FA-SC25U: 400430 MHz FA-SC72U: 470520 MHz FA-SC55V: 146174 MHz (The same as supplied with the transceiver) FA-SC57U: 440470 MHz FA-SC25V: 136155 MHz FA-SC56VS: 150162 MHz HS-95: Neck-arm type 8 33
!IC-F14_F24.qxd 04.6.17 6:22 PM Page 34 (1,1) A-6369D-1EX Printed in Japan 2004 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2012-12-19 | 406.1 ~ 470 | TNF - Licensed Non-Broadcast Transmitter Held to Face | Class II permissive change or modification of presently authorized equipment |
2 | 2009-06-30 | 406.1 ~ 470 | TNF - Licensed Non-Broadcast Transmitter Held to Face | |
3 | 2004-09-17 | 400 ~ 470 | TNF - Licensed Non-Broadcast Transmitter Held to Face | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 3 | Effective |
2012-12-19
|
||||
1 2 3 |
2009-06-30
|
|||||
1 2 3 |
2004-09-17
|
|||||
1 2 3 | Applicant's complete, legal business name |
ICOM Incorporated
|
||||
1 2 3 | FCC Registration Number (FRN) |
0005855366
|
||||
1 2 3 | Physical Address |
1-1-32 Kamiminami
|
||||
1 2 3 |
Osaka, N/A 547-0003
|
|||||
1 2 3 |
Japan
|
|||||
app s | TCB Information | |||||
1 2 3 | TCB Application Email Address |
v******@ultratech-labs.com
|
||||
1 2 3 |
h******@americantcb.com
|
|||||
1 2 3 | TCB Scope |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
||||
app s | FCC ID | |||||
1 2 3 | Grantee Code |
AFJ
|
||||
1 2 3 | Equipment Product Code |
277601
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 3 | Name |
A****** T******
|
||||
1 2 3 | Title |
General Manager
|
||||
1 2 3 | Telephone Number |
+8166********
|
||||
1 2 3 | Fax Number |
+8166********
|
||||
1 2 3 |
w******@icom.co.jp
|
|||||
app s | Technical Contact | |||||
1 2 3 | Firm Name |
UltraTech Engineering Labs Inc.
|
||||
1 2 3 |
Ultratech Engineering Labs Inc.
|
|||||
1 2 3 | Name |
J****** C****
|
||||
1 2 3 |
T**** L********
|
|||||
1 2 3 | Physical Address |
3000 Bristol Circle
|
||||
1 2 3 |
Oakville, ON, L6H6G4
|
|||||
1 2 3 |
Oakville, L6H 6G4
|
|||||
1 2 3 |
Canada
|
|||||
1 2 3 | Telephone Number |
905-8********
|
||||
1 2 3 | Fax Number |
905-8********
|
||||
1 2 3 |
j******@ultratech-labs.com
|
|||||
1 2 3 |
t******@ultratech-labs.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 3 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 2 3 | Yes | |||||
1 2 3 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 3 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 3 | Equipment Class | TNF - Licensed Non-Broadcast Transmitter Held to Face | ||||
1 2 3 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | UHF Transceivers | ||||
1 2 3 | UHF Transceiver | |||||
1 2 3 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 3 | Yes | |||||
1 2 3 | Modular Equipment Type | Does not apply | ||||
1 2 3 | Purpose / Application is for | Class II permissive change or modification of presently authorized equipment | ||||
1 2 3 | Original Equipment | |||||
1 2 3 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 2 3 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 3 | Grant Comments | Note 1: 16K0F3E, 11K0F3E Power listed is conducted. This device must be restricted to work related operations in an Occupational/Controlled RF exposure Environment, not exceeding a maximum transmitting duty factor of 50%. All qualified end-users of this device must have the knowledge to control their exposure conditions and/or duration to comply with the Occupational/Controlled MPE limit and requirements. A label, as described in this filing, must be displayed on the device to direct users to specific training information for meeting Occupational Exposure Requirements. SAR compliance for body-worn operating configurations is limited to the specific belt-clip tested for this filing. End-users must be informed of the body-worn operating requirements for satisfying RF exposure compliance. The highest reported SAR levels are: Face Held: 3.77W/kg for 50% Duty Cycle; Body Worn: 5.73W/kg for 50% Duty Cycle. Class II permissive change: To add new accessories and antenna. The highest reported SAR levels with new antenna (M/N: FA-SC61UC) are: Face Held: 3.70 W/kg for 50% Duty Cycle; Body Worn: 5.75 W/kg for 50% Duty Cycle. Class II Permissive Change to add a new battery pack, model BP-232H (7,4V, 2300 mAh), which is same family but longer life compared to initially certified model BP-232N (7,4V, 2000 mAh). The highest reported SAR levels with new battery are: Body Worn: 4.75 W/kg for 50% Duty Cycle. | ||||
1 2 3 | Power listed is conducted. This device must be restricted to work related operations in an Occupational/Controlled RF exposure Environment, not exceeding a maximum transmitting duty factor of 50%. All qualified end-users of this device must have the knowledge to control their exposure conditions and/or duration to comply with the Occupational/Controlled MPE limit and requirements. A label, as described in this filing, must be displayed on the device to direct users to specific training information for meeting Occupational Exposure Requirements. SAR compliance for body-worn operating configurations is limited to the specific belt-clip tested for this filing. End-users must be informed of the body-worn operating requirements for satisfying RF exposure compliance. The highest reported SAR levels are: Face Held: 3.77W/kg for 50% Duty Cycle; Body Worn: 5.73W/kg for 50% Duty Cycle. Class II permissive change: To add new accessories and antenna. The highest reported SAR levels with new antenna (M/N: FA-SC61UC) are: Face Held: 3.70 W/kg for 50% Duty Cycle; Body Worn: 5.75 W/kg for 50% Duty Cycle. | |||||
1 2 3 | Power listed is conducted. This device must be restricted to work related operations in an Occupational/Controlled RF exposure Environment, not exceeding a maximum transmitting duty factor of 50%. All qualified end-users of this device must have the knowledge to control their exposure conditions and/or duration to comply with the Occupational/Controlled MPE limit and requirements. A label, as described in this filing, must be displayed on the device to direct users to specific training information for meeting Occupational Exposure Requirements. SAR compliance for body-worn operating configurations is limited to the specific belt-clip tested for this filing. End-users must be informed of the body-worn operating requirements for satisfying RF exposure compliance. The highest reported SAR levels are: Face Held: 3.77W/kg for 50% Duty Cycle; Body Worn: 5.73W/kg for 50% Duty Cycle. | |||||
1 2 3 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 3 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 3 | Firm Name |
UltraTech Engineering Labs Inc.
|
||||
1 2 3 | Name |
T******** L******
|
||||
1 2 3 | Telephone Number |
905-8********
|
||||
1 2 3 | Fax Number |
905-8********
|
||||
1 2 3 |
t******@ultratech-labs.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 90.21 | EF | 400 | 406 | 4 | 2.5 ppm | NOTE 1 | |||||||||||||||||||||||||||||||||
1 | 2 | 90.21 | EF | 400 | 406 | 1 | 2.5 ppm | NOTE 1 | |||||||||||||||||||||||||||||||||
1 | 3 | 90.21 | EF | 406.1 | 470 | 4 | 2.5 ppm | NOTE 1 | |||||||||||||||||||||||||||||||||
1 | 4 | 90.21 | EF | 406.1 | 470 | 1 | 2.5 ppm | NOTE 1 | |||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 90.21 | EF | 406.1 | 470 | 4 | 2.5 ppm | 11K0F3E | |||||||||||||||||||||||||||||||||
2 | 2 | 90.21 | EF | 406.1 | 470 | 4 | 2.5 ppm | 16K0F3E | |||||||||||||||||||||||||||||||||
2 | 3 | 90.21 | EF | 406.1 | 470 | 1 | 2.5 ppm | 11K0F3E | |||||||||||||||||||||||||||||||||
2 | 4 | 90.21 | EF | 406.1 | 470 | 1 | 2.5 ppm | 16K0F3E | |||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
3 | 1 | 90.21 | 400 | 470 | 4 | 2.5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
3 | 2 | 90.21 | 400 | 470 | 4 | 2.5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
3 | 3 | 90.21 | 400 | 470 | 1 | 2.5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
3 | 4 | 90.21 | 400 | 470 | 1 | 2.5 ppm | 16K0F3E |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC