FCC ID: AFJ332902 UHF Transceiver

Limited functions only Limited functions only INSTRUCTION MANUAL VHF TRANSCEIVERS iF3100D Series UHF TRANSCEIVERS iF4100D Series This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. FOREWORD READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL This instruc-

tion manual contains important operating instructions for the IC-

F3101D/IC-F3103D/IC-F3106D VHF TRANSCEIVERS and the IC-F4101D/IC-F4103D/IC-F4106D UHF TRANSCEIVERS. EXPLICIT DEFINITIONS WORD RDANGER!

RWARNING!

CAUTION NOTE DEFINITION Personal death, serious injury or an explo-

sion may occur. Personal injury, fire hazard or electric shock may occur. Equipment damage may occur. If disregarded, inconvenience only. No risk of personal injury, fire or electric shock. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorpo-

rated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. i FCC INFORMATION FOR CLASS B UNINTENTIONAL RADIATORS:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION: Changes or modifications to this device, not expressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations. ii PRECAUTIONS R DANGER! NEVER short the terminals of the battery pack. R DANGER! Use and charge only specified Icom battery packs with Icom radios or Icom chargers. Only Icom battery packs are tested and approved for use with Icom radios or charged with Icom chargers. Using third-party or counterfeit battery packs or chargers may cause smoke, fire, or cause the battery to burst. R WARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 inches) away from the lips and the transceiver is vertical. R WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. Hearing experts advise against continuous high volume operation. If you experience a ringing in your ears, reduce the volume level or discontinue use. R WARNING! NEVER operate the transceiver while driving a vehicle. Safe driving requires your full attentionanything less may result in an accident. CAUTION: MAKE SURE the flexible antenna and battery pack are securely attached to the transceiver, and that the antenna and battery pack are dry before attachment. Exposing the inside of the transceiver to water will result in serious damage to the trans-

ceiver. DO NOT operate the transceiver near unshielded electrical blast-

ing caps or in an explosive atmosphere. DO NOT push [PTT] when not actually intending to transmit. DO NOT use or place the transceiver in direct sunlight or in areas with temperatures below 30C (+22F) or above +60C (+140F). iii DO NOT modify the transceiver. The transceiver warranty does not cover any problems caused by unauthorized modification. DO NOT use harsh solvents such as benzine or alcohol when cleaning, as they will damage the transceiver surfaces. BE CAREFUL! The transceiver will become hot when operating it continuously for long periods of time. KEEP the transceiver away from heavy rain, and never immerse it in the water. The transceiver meets IP54* requirements for dust-

protection and splash resistance. However, once the transceiver has been dropped, dust-protection and splash resistance cannot be guaranteed because of possible damage to the transceivers case or the waterproof seal.

* Only when the battery pack/case and jack cover are attached. Even when the transceiver power is OFF, a slight current still flows in the circuits. Remove the battery pack or batteries from the trans-

ceiver when not using it for a long time. Otherwise, the installed battery pack or batteries will become exhausted, and will need to be recharged or replaced. MAKE SURE to turn the transceiver power OFF before connect-

ing the supplied/optional equipment. iv VOICE CODING TECHNOLOGY The AMBE+2 voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Com-

munications Equipment. The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Patent Nos.

#5,870,405, #5,826,222, #5,754,974, #5,701,390, #5,715,365,

#5,649,050, #5,630,011, #5,581,656, #5,517,511, #5,491,772,

#5,247,579, #5,226,084 and #5,195,166. v SUPPLIED ACCESSORIES The following accessories are supplied with the transceiver. Battery pack*

Flexible antenna

(This illustration is for the VHF type.) Battery charger*

AC adapter*

Belt clip*

Jack cover

(with screws)

* Not supplied, or the shape is different, depending on the version. vi TABLE OF CONTENTS FOREWORD ........................................................................................ i EXPLICIT DEFINITIONS ...................................................................... i FCC INFORMATION ........................................................................... ii PRECAUTIONS .............................................................................. iii, iv VOICE CODING TECHNOLOGY ........................................................ v SUPPLIED ACCESSORIES ............................................................... vi TABLE OF CONTENTS ................................................................ vii, vii 1 ACCESSORIES ......................................................................... 14 Accessory attachments .............................................................. 1 2 PANEL DESCRIPTION ............................................................ 511 Front, top and side panels .......................................................... 5 LED indicator .............................................................................. 7 Programmable function keys ...................................................... 8 3 BASIC OPERATION .............................................................. 1224 Turning power ON ..................................................................... 12 Channel selection ..................................................................... 13 Call procedure .......................................................................... 14 Receiving and transmitting ....................................................... 15 Setting the microphone gain ..................................................... 18 Setting the squelch level ........................................................... 19 Setting the Beep level ............................................................... 20 Setting the Ringer level ............................................................. 21 Output power level selection ..................................................... 22 Priority A channel selection ...................................................... 22 MDC 1200 system operation .................................................... 23 Lone Worker Emergency Call ................................................... 23 Emergency Call ........................................................................ 24 4 IDAS OPERATION ................................................................. 2530 IDAS operation ......................................................................... 25 IDAS-Trunk operation ............................................................... 25 Receiving a call......................................................................... 26 vii Transmitting a call ..................................................................... 28 Position data transmission ........................................................ 30 Status message transmission ................................................... 30 Encryption function ................................................................... 30 5 BATTERY CHARGING .......................................................... 3141 Caution (for the BP-264 ni-mh battery) .................................... 31 Caution (for the BP-265 Li-ion battery) .................................... 33 Battery chargers ....................................................................... 36 6 BATTERY CASE .......................................................................... 42 Optional battery case (BP-263) ................................................ 42 7 OPTIONS ............................................................................... 4348 VOX function ............................................................................. 46 8 SAFETY TRAINING INFORMATION ..................................... 4950 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 viii 1 ACCESSORIES Accessory attachments D Flexible antenna Connect the flexible antenna to the antenna connector. CAUTION:

NEVER HOLD just the antenna when carrying the transceiver. Transmitting without an antenna will damage the transceiver. 1 ACCESSORIES 1 D Belt clip To attach the belt clip:

Slide the belt clip in the direction of the arrow until the belt clip locks in place, and makes a click sound. Belt clip Battery pack To detach the belt clip:

q Remove the battery pack from the transceiver, if it is attached.

(p. 3) w Lift the tab up (q), and slide the belt clip in the direction of the arrow (w). q Tab w 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 2 1 ACCESSORIES D Battery pack or case To attach the battery pack or case:

q Fit the battery pack/case in the direction of the arrow, then close it. w Hook the latch until it makes a click sound. q Battery pack/case w Latch To remove the battery pack/case:

Be careful! The latch is tightly locked, so use caution when re-

leasing it. DO NOT use your finger nail. Use the edge of a coin or screwdriver tip to carefully release it. q Unhook the latch. w Lift up the battery pack/case in the direction of the arrow. w q 3 ACCESSORIES 1 NEVER remove or attach the battery pack/case when the trans-

ceiver is wet or soiled. This may result in water or dust getting into the transceiver, battery pack/case, and may result in them being damaged. NOTE: Keep the battery terminals clean. Its a good idea to clean the battery terminals once a week. D Jack cover Attach the jack cover when the optional equipment is not used. To attach the jack cover:

q Attach the jack cover to the To detach the jack cover:

q Remove the screws with a

[SP MIC] jack. w Tighten the screws. phillips screwdriver. w Detach the jack cover to con-

nect the optional equipment. q w w q q w 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 4 2 PANEL DESCRIPTION Front, top and side panels i ANTENNA CONNECTOR u PTT SWITCH y UPPER KEY t LOWER KEY q ROTARY SELECTOR w e VOLUME CONTROL LED INDICATOR Speaker r SPEAKER-

MICROPHONE JACK Microphone q ROTARY SELECTOR Rotate to select the pre-programmed memory channels or scan lists, depending on the pre-programming. w VOLUME CONTROL [VOL]

Rotate to turn the power ON or OFF, and adjust the audio level. 5 PANEL DESCRIPTION 2 e LED INDICATOR (p. 7) Lights red* while transmitting.

* When the optional battery case is attached, the LED indicator lights orange. Lights green while receiving a signal, or when the squelch is open. Lights/blinks orange when the matched 2/5-tone code is re-

ceived, depending on the pre-programming. r SPEAKER-MICROPHONE JACK [SP MIC]

Connect the optional speaker-microphone or VOX adapter cable. Jack cover NOTE: Attach the jack cover when the optional equipment is not used. (p. 4) t LOWER KEY [Lower]

y UPPER KEY [Upper]

The desired function can be assigned by your dealer. (p. 8) u PTT SWITCH [PTT]

Hold down to transmit; release to receive. i ANTENNA CONNECTOR Connect the antenna. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 6 2 PANEL DESCRIPTION LED indicator The LED indicator indicates the status of various parameters of the transceiver as follows;

(Ref.; R=Red, G=Green, O=Orange) TX: Lights Red while transmitting a signal. R *

RX: Lights Green while receiving a signal. G Call LED (ON): Turns ON while receiving a matched 2/5-tone. Call LED ON O Call LED (Blink): Blinks while receiving a matched 2/5-tone. Call LED Blink O O Fast/Slow scan: Blinks when the Fast/Slow scan is activated. F/S Scan G G Low Battery 1: You should charge the battery. (blinks slowly) G G Low BATT1 Low BATT2 Low Battery 2: You must charge the battery. (blinks fast) G G TX low Battery 1: Low Battery was detected during TX mode. G G TX Low BATT1 R*

R*

TX low Battery 2: Very Low Battery was detected during TX mode. TX Low BATT2 R*

R*

R*

R*

Channel Error: A non-programmed channel is selected. R O R O R O R O R O R O R O R O

* Lights (or blinks) orange when the optional battery case is attached. 7 PANEL DESCRIPTION 2 Programmable function keys The following functions can be assigned to the [Upper] and [Lower]

programmable function keys. Consult your Icom dealer or system operator for details concerning your transceivers programming. SCAN Push to start and cancel the scanning operation. When the scan started with the Power ON Scan or Auto Scan func-

tion, push to pause the scanning operation. The paused scan re-

sumes after the specified time period has passed. PRIORITY A CHANNEL, PRIORITY B CHANNEL Push to select the Priority A or Priority B channel. PRIORITY A CHANNEL (REWRITE), PRIORITY B CHANNEL (REWRITE) Push to select the Priority A or Priority B channel. Hold down [Prio A (Rewrite)] or [Prio B (Rewrite)] for 1 second to assign the operating channel to Priority A or Priority B channel, respectively. MEMORY CHANNELS 1, 2, 3, 4 Push to directly select memory channel 1, 2, 3 or 4, if programmed. Consult your dealer for details. LONE WORKER (p. 24) Push to turn the Lone Worker function OFF. Hold down to turn the Lone Worker function ON. When the Lone Worker function is turned ON, and no operation is performed for the specified time period, the Emergency function is automatically turned ON. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 8 2 PANEL DESCRIPTION MONITOR, MONITOR (AUDIBLE) Push to turn the CTCSS (DTCS) or 2/5-tone squelch Mute ON or OFF. Only during LMR operation, push to open any squelch func-

tions, or deactivate any mute functions. Only during PMR operation, push to activate one or two of the following functions* on each channel.

- Hold down to un-mute the channel (Audible mode).

- Push to mute the channel (Inaudible mode).

- Push to send a reset code after the communication is finished.

*Ask your dealer for details. NOTE: The un-mute condition may automatically return to the mute condition, after a specified time period. Depending on the presetting, holding down this key for 1 sec-

ond cancels a scan. LOCK Hold down to electronically lock all programmable keys except

[Moni(Audi)], [Call] (including Call A and Call B), [Emergency], Surveillance] and [Lone Worker]. HIGH/LOW (p. 22) Select the transmit output power level temporarily or permanently, depending on the presetting. Ask your dealer for the output power level for each selection. TALK AROUND Push to turn the Talk Around function OFF. Hold down to turn the Talk Around function ON. The Talk Around function equalizes the transmit frequency to the receive frequency for transceiver-to-transceiver communication. DTMF AUTODIAL Push to transmit a programmed DTMF code. 9 PANEL DESCRIPTION 2 WIDE/NARROW Push to switch the IF bandwidth to Wide. The wide passband width can be selected from 20 or 25 kHz using the optional cloning software (PMR operation only). Ask your dealer for details. Hold down to switch the IF bandwidth to Narrow. CALL, CALL A, CALL B Push to transmit a 2/5-tone code. Tone call transmission may be necessary before you call another sta-

tion, depending on your signalling system.

[Call A] and/or [Call B] keys may be available when your system em-

ploys selective Individual/Group calls. Ask your dealer which call is assigned to each key. EMERGENCY Hold down for specified time period to transmit an emergency call. The emergency call transmits with beeps, and the LED lights red. The transceiver can transmit an emergency call without the beep sounding and the LED indicator lighting. Ask your dealer for details. If you want to cancel the emergency call, hold down the key again before transmitting the call. The emergency call is transmitted one time only, or repeatedly until re-

ceiving an acknowledgement signal, or until the power is turned OFF. When a matched 5-tone code signal is received, the emergency func-

When a matched 5-tone code signal is received, the emergency func-

tion can be cancelled depending on the presetting. (PMR operation only) SURVEILLANCE Push to turn the Surveillance function OFF. Hold down to turn the Surveillance function ON. When this function is turned ON, the beep is not heard and the LED does not light when a signal is received, or a key is pushed. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 10 2 PANEL DESCRIPTION SIREN Hold down for 1 second to emit a siren sound. This function can be used for situations other than an emergency alert, such as a security alarm for example. The transceiver emits the siren sound until the power is turned OFF. ENCRYPTION Push to turn the Voice Encryption function ON or OFF while operat-

ing in the digital mode. ANNOUNCE Push to turn the Channel Announce function ON or OFF. When this function is turned ON, the transceiver announces the posi-

tion of [ROTARY SELECTOR] between 1 and 16 when rotating [RO-

TARY SELECTOR] to a desired scale. 11 BASIC OPERATION Turning power ON 3 Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. (p. 31) Rotate [VOL] to turn power ON.

[VOL]

D Battery type selection The battery type must be selected according to the battery pack or case when it is changed, but only the first time it is used. Check the battery type before you begin the selection procedure. One to three beep(s) sound in sequence, so you must repeat the steps until the number of beeps matches your battery type. For example, if your battery type is a Li-ion battery pack, you must repeat the procedure until one beep is heard. q Set [ROTARY SELECTOR] to any channel other than Channel 16. w Rotate [VOL] to turn OFF the trans-

ceivers power. e While holding down [PTT], rotate

[VOL] to turn ON the power. You should hold [PTT] until the beep sounds. (It takes approximately 5 second.) One beep sounds when the Li-ion battery is selected.

[ROTARY SELECTOR]

[VOL]

[PTT]

Two beeps sound when the battery case is selected. Three beeps sound when the Ni-MH battery is selected. r After the beep sounds, release [PTT]. t Repeat steps w to r until you select the attached battery type. NOTE: This operation may not be available, depending on the presetting. Ask your dealer for details. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 12 3 BASIC OPERATION Channel selection Several types of channel selecting methods are available. They may differ, according to your system set up. To select a desired operating channel, do one of the following. Rotate [ROTARY SELECTOR]. Push one of memory channel keys, [MR-CH 1] to [MR-CH 4]. Push one of these keys, [Prio A], [Prio B], [Prio A (Rewrite)] and

[Prio B (Rewrite)]. AUTOMATIC SCAN TYPE:

Selecting a channel is not necessary for this type. When turning ON the power, the transceiver automatically starts scanning. Scanning stops when a call is received. NOTE: If the Move to Priority A channel at Power ON function

(p. 22) is turned ON, the transceiver does not start scanning at power ON. 13 BASIC OPERATION 3 Call procedure When your system employs tone signalling (excluding CTCSS and DTCS), the tone call procedure may be necessary prior to voice transmission. The tone signalling that is employed in the transceiver may be a selective calling system, which allows you to call only specific station(s), and prevent unwanted stations from contacting you. q Select a desired TX code channel or 2/5-tone code, according to your System Operators instructions. This may not be necessary, depending on programming. w Push [Call] (assigned to one of the dealer programmable keys.)

(p. 10) e After transmitting a 2/5-tone code, the remainder of your com-

munication can be carried out normally. Selective calling Non-selective calling 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 14 3 BASIC OPERATION Receiving and transmitting CAUTION: Transmitting without an antenna will damage the transceiver. See page 1 for antenna attachment. Receiving:

q Rotate [VOL] to turn ON the power. w Rotate [ROTARY SELECTOR], or push one of the memory chan-

nel keys, [MR-CH 1] to [MR-CH 4], to select a channel. e When receiving a call, adjust the audio output to a comfortable listening level. NOTE: When a matched RX code signal is received, audio from the microphone is automatically transmitted for a specified time period.*

* Depending on the presetting. Ask your dealer for details. Transmitting:

Wait for the channel to become clear to avoid interference. q While holding down [PTT], speak into the microphone at a nor-

mal voice level. w Release [PTT] to return to receive. IMPORTANT: To maximize the readability of your signal;

1. Pause briefly after pushing [PTT]. 2. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak into the microphone at a normal voice level. 15 BASIC OPERATION 3 D Transmitting notes Transmit inhibit function The transceiver has several inhibit functions, which restrict trans-

mission under the following conditions:

- The channel is muted. (PMR operation only)

- The channel is busy.

- A signal with the un-matched (or matched) CTCSS (or DTCS) tone is received.

- The selected channel is a receive only channel. Time-out timer After continuously transmitting longer than the pre-programmed time period, the time-out timer activates, and stops further transmitting. Penalty timer Once the time-out timer activates, transmitting is further inhibited for a time period determined by the penalty timer. PTTID call The transceiver automatically sends the ID code (5-tone, DTMF, BIIS, MDC system or IDAS operations) when [PTT] is pushed (be-

ginning of the transmission) and/or released (end of transmission), depending on the presetting. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 16 3 BASIC OPERATION D DTMF transmission If the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is usable. Push [DTMF Autodial] to transmit the DTMF code. D Receiving a Stun, Kill and Revive command The dispatcher can send a 2/5-tone signal that will stun, kill or re-

vive your transceiver. When the Stun command is received, a beep sounds*, and the transceiver becomes unusable. Receiving a Revive command is necessary to operate the transceiver again in this case. When the Kill command is received, a beep sounds*, and the trans-

ceiver becomes unusable (the transceiver switches to the cloning required condition). Cloning the transceiver is necessary to operate the transceiver again in this case.

* Depending on the presetting. Ask your dealer for details. 17 Setting the microphone gain Adjusts the microphone gain. BASIC OPERATION 3 q Rotate [VOL] to turn the trans-

ceiver power OFF. w Set [ROTARY SELECTOR] to Channel 16. e While holding down [Upper], ro-

tate [VOL] to turn ON the power and enter the microphone gain adjustment mode. r Push [Upper] to increase, or push [Lower] to decrease the microphone gain. The adjustable range is 1 (mini-

[ROTARY SELECTOR]

[VOL]

[Upper]

mum) to 4 (maximum). A beep sounds after pushing

[Upper] or [Lower]. An error beep sounds if you try to decrease more than 1 or try to increase more than 4. Therefore, you can determine the current level setting by the type of beep that sounds. t Rotate [VOL] to turn the power OFF, then ON again to exit the microphone gain adjustment mode. NOTE:

This operation may not be available, depending on the preset-

ting. Ask your dealer for details. When using the VOX function, we recommend setting the mi-

crophone gain to 3. However, you can adjust it to suit your op-

erating environment (including your headset performance). 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 18 3 BASIC OPERATION Setting the squelch level The squelch circuit mutes the received audio signal, depending on the signal strength. q Rotate [VOL] to turn the trans-

ceiver power OFF. w Set [ROTARY SELECTOR] to any channel other than Chan-

nel 16. e While holding down [Upper], ro-

tate [VOL] to turn ON the power and enter the squelch level ad-

justment mode. r Push [Upper] to increase the squelch level (tight squelch), or push [Lower] to decrease the squelch level (loose squelch). The adjustable range is 0 (loose

[ROTARY SELECTOR]

[VOL]

[Upper]

squelch) to 9 (tight squelch). A beep sounds after pushing

[Upper] or [Lower]. An error beep sounds if you try to decrease more than 0 or try to increase more than 9. Therefore, you can determine the current level setting by the type of beep that sounds. t Rotate [VOL] to turn the power OFF, then ON again to exit the squelch level adjustment mode. NOTE: This operation may not be available, depending on the presetting. Ask your dealer for details. 19 BASIC OPERATION 3 Setting the Beep level The beep function can be turned ON or OFF, and its level can be adjusted between 1 and 5, or 1 (linked) and 5 (linked). When a Linked option is selected, the beep level is adjustable with [VOL]. q Rotate [VOL] to turn the trans-

ceiver power OFF. w Set [ROTARY SELECTOR] to any channel other than Chan-

nel 16. e While holding down [Lower], ro-

tate [VOL] to turn ON the power and enter the beep level adjust-

ment mode. r Push [Upper] to change the beep level, or push [Lower] to turn the beep function ON or OFF. The adjustable range is 1 to 5 or

[ROTARY SELECTOR]

[VOL]

[Lower]

1 (Linked) to 5 (Linked). If the level is set on 1 to 4 or 1

(Linked) to 4 (Linked), pushing

[Upper] increases the level. If the level is 5 or 5 (Linked), 1 (Linked) or 1 is selected after push-

ing [Upper], respectively. A beep sounds after pushing [Upper]. Therefore, you can deter-

mine the current level setting by the type of beep that sounds. One beep sounds when the beep function is turned ON after push-

ing [Lower]. t Rotate [VOL] to turn the power OFF, then ON again to exit the beep level adjustment mode. NOTE: This operation may not be available, depending on the presetting. Ask your dealer for details. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 20 3 BASIC OPERATION Setting the Ringer level The Ringer level can be adjusted between 1 and 5, or 1 (Linked) and 5 (Linked). When a Linked option is selected, the Ringer level is adjustable with [VOL]. q Rotate [VOL] to turn the trans-

ceiver power OFF. w Set [ROTARY SELECTOR] to Channel 16. e While holding down [Lower], ro-

tate [VOL] to turn ON the power and enter the Ringer level ad-

justment mode. r Push [Upper] to increase, or push [Lower] to decrease the Ringer level. The adjustable range is 1 to 5 or

[ROTARY SELECTOR]

[VOL]

[Lower]

1 (Linked) to 5 (Linked). If the level is set on 5 or 5

(Linked), pushing [Upper] selects 1 (Linked) or 1, respectively. If the level is 1 or 1 (Linked), pushing

[Lower] selects 5 (Linked) or 5, respectively. A beep sounds after pushing [Upper] or [Lower]. Therefore, you can determine the current level setting by the type of beep that sounds. t Rotate [VOL] to turn the power OFF, then ON again to exit the beep level adjustment mode. NOTE: This operation may not be available, depending on the presetting. Ask your dealer for details. 21 BASIC OPERATION 3 Output power level selection If the transceiver has [High/Low] assigned to it, the transmit output power level can be selected, depending on the presetting. When the battery case is selected as the battery type, or the bat-

tery voltage drops to a low power level and the LED indicator sta-

tus is Low Battery 2, the output power automatically switches to Low 1. (pp. 7, 12) Push [High/Low] to select the transmit output power level. One beep sounds when Low 1 is selected. Two beeps sound when Low 2 is selected. Three beeps sound when High is selected. Priority A channel selection When one of the following operations is performed, the transceiver automatically selects the Priority A channel. Turning the power ON The Priority A channel is selected each time the transceiver pow-

er is turned ON. Auto reset The Priority A channel is selected when the Auto Reset timer ends. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 22 3 BASIC OPERATION MDC 1200 system operation The MDC 1200 signaling system enhances your transceivers capa-

bilities. It allows PTT ID* and Emergency signaling.

* When [PTT] is pushed and/or released, the transceiver transmits your station ID. D Transmitting an Emergency Call The MDC 1200 systems Emergency feature can be accessed using the [Emergency] key. The transceiver will send an Emergency MDC 1200 system command once, or repeatedly for a programmed number of times until it receives an acknowledgement signal. The emergency call can be transmitted without a beep sound, de-

pending on how the emergency function is programmed. Ask your dealer for details. Lone Worker Emergency Call When the Lone Worker function is turned ON, and no operation is performed for the specified time period*, the transceiver enters the emergency mode, and then the countdown for the emergency call transmission starts. After the specified time period* has passed, an emergency call is automatically transmitted once, or repeatedly*. If someone operates the transceiver before the call is transmitted, the transceiver exits the emergency mode, and the emergency call is can-

celled.

* Depending on the presetting. Ask your dealer for details. q Hold down [Lone Worker] to turn ON the Lone Worker function. w Push [Lone Worker] to turn OFF the Lone Worker function. 23 BASIC OPERATION 3 Emergency Call When [Emergency] is held down for the specified time period*, the emergency signal is transmitted once, or repeatedly, on the speci-

fied emergency channel. A repeat emergency signal is automatically transmitted until you turn the power OFF. Depending on the pre-programmed settings, receiving a matching 5-tone code cancels the transmission. When no emergency channel is specified, the signal is transmitted on the previously selected channel. If you want to cancel the emergency call, hold down [Emergency]

again before transmitting the call. If your transceiver is programmed for Silent operation, you can transmit an Emergency call without the beep sounding and the LED indicator lighting. IMPORTANT: It is recommended to set an emergency channel individually to provide the certain emergency call operation. D NOTES Depending on the presetting, the following functions are automati-

cally activated. Ask your dealer for details. Auto TX function After the emergency call transmission, audio from the microphone is automatically transmitted for a specified time period.*

Auto RX function After the emergency call transmission, the transceiver stands by in the audible mode for the specified time period.*

* Depending on the presetting. Ask your dealer for details. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 24 4 IDAS OPERATION IDAS operation The IC-F3100D series and IC-F4100D series provide Icom Digital Advanced System (IDAS) that meets the 6.25 kHz emission mask requirements for narrow banding, and increases efficiency of chan-

nel allocation and use of spectrum. NOTE: During IDAS operation, BIIS 1200 and MDC 1200 sys-

tem operations are not available. IDAS-Trunk operation The IDAS-Trunk system enables further effective channel manage-

ment by sharing a minimum of channels with a large number of users. Rotate [ROTARY SELECTOR] to select the memory channel that is programmed in the IDAS-Trunk zone. NOTE: During IDAS-Trunk operation, you can receive and trans-

mit digital calls in the same way with the following IDAS opera-

tion. 25 IDAS OPERATION 4 Receiving a call D Receiving a Call Alert q When a Call Alert is received;

w Hold down [PTT], then speak into the microphone. e Release [PTT] to receive a response. The transceiver will automatically transmit the acknowledgement. The LED indicator blinks orange. Beeps sound. NOTE: The LED indicator or Beeps may differ, depending on the presetting. Ask your dealer for details. D Receiving a Stun, Kill or Revive If an individual call with Stun or Kill command is received (RAN code matching is not necessary depending on the presetting), the transceiver will automatically transmit the acknowledgement, and then you cannot receive* or transmit.

* Depending on the received Stun command setting. When a Stun command is received;

The transceiver cannot be operated until the individual call with Revive command is received (RAN code matching is not nec-

essary depending on the presetting) or until the data cloning is performed. Even if [ROTARY SELECTOR] is changed, the transceiver will keep the same channel as the Stun command is received. When a Kill command is received;

The LED indicator alternately blinks red and green. The transceiver cannot be operated until the data cloning is performed. Ask your dealer for details. NOTE: Depending on the presetting, the transceiver ignores the Stun, Revive and Kill commands, which are from a non-specified station. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 26 4 IDAS OPERATION D Receiving a Remote Monitor or Radio Check Call If an individual call with Remote monitor or Radio check command is received (RAN code matching is not necessary depending on the presetting), the transceiver will automatically transmit. When a Remote monitor command is received;

The transceiver will automatically transmit the acknowledge-

ment, and then it transmits the microphone audio for the set time period. When a Radio check command is received;

The transceiver will automatically transmit the acknowledge-

ment. 27 IDAS OPERATION 4 Transmitting a call IDAS operation allows you to make a call to a specific station (In-

dividual call) or to a particular group (Talkgroup call). Other digital mode transceivers on the channel will not receive a call that does not match their individual or talkgroup ID and/or RAN (Radio Ac-

cess Number) code. D Transmitting an Emergency Call When [Emergency] is held down for the specified time period, the emergency signal (digital command) is transmitted once or repeat-

edly* on the specified emergency channel. When no emergency chan-

nel is specified, the signal is transmitted on the operating channel.

* When the Repeat Cancel function is ON, the transceiver cancels repeating after receiving an acknowledgement. When the Repeat Cancel function is OFF, the transceiver repeats calling according to the number of repeat cycles, even after re-

ceiving an acknowledgement. Individual or Talkgroup call types of emergency calls can be pre-

fixed. If the call type is not pre-fixed, the default or selected call type is used. If you want to cancel the emergency call, hold down [Emergency]

again before transmitting the call. If your transceiver is programmed for Silent operation, you can transmit an Emergency call without the beep sounding and the LED indicator lighting. The transceiver can also be programmed to keep the microphone open during an emergency call, allowing monitoring of the situation. Ask your dealer for details. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 28 4 IDAS OPERATION IMPORTANT: It is recommended to set an emergency channel individually to provide the certain emergency call operation. NOTE: The Digital Request Ack function is activated, the trans-

ceiver transmits the emergency call with the request to send back an acknowledgment. 29 IDAS OPERATION 4 Position data transmission When an optional HM-171GP or any other GPS receiver is con-

nected to the transceiver, the position (longitude and latitude) data can be transmitted automatically when;

After sending a Status Call

- Set the Send with Status Call item as Enable. After sending an Emergency Call

- Set the Send with Emergency item as Enable. After sending a Voice Call

- Set the Send with Voice Call item as Enable. Ask your dealer or system operator for connection details. Status message transmission The status message can be transmitted automatically. The status message is transmitted when the transceiver is turned ON or OFF.

- Select a status message to be transmitted in Power ON Status or Power OFF Status item, respectively.

- Select a target station ID in Power Status ID. Encryption function The encryption function enables voice scrambling, which provides private digital communication between stations. Push [Encryption] to turn the encryption function ON or OFF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 30 5 BATTERY CHARGING Caution (for the BP-264 ni-mh battery) R DANGER! NEVER short terminals (or charging terminals) of the battery pack. Also, current may flow into nearby metal objects such as a necklace, so be careful when placing battery packs (or the transceiver) in handbags, etc. Simply carrying with or placing near metal objects such as a neck-

lace, etc. may cause shorting. This may damage not only the bat-

tery pack, but also the transceiver. R DANGER! NEVER incinerate used battery packs. Internal bat-

tery gas may cause an explosion. R DANGER! NEVER immerse the battery pack in water. If the bat-

tery pack becomes wet, be sure to wipe it dry BEFORE attaching it to the transceiver. CAUTION: Always use the battery within the specified temperature range, 5C to +60C (+23F to +140F). Using the battery out of its specified temperature range will reduce the batterys performance and battery life. CAUTION: Shorter battery life could occur if the battery is left com-

pletely discharged, or in an excessive temperature environment

(above +55C; +131F) for an extended period of time. If the battery must be left unused for a long time, it must be detached from the radio after charging. Keep it safely in a cool dry place at the follow-

ing temperature range:

20C to +45C (4F to +113F) 20C to +35C (4F to +95F) 20C to +25C (4F to +77F)

* We recommend charging the battery pack every 6 months. Clean the battery terminals to avoid rust or misscontact. Keep the battery terminals clean. Its a good idea to clean the bat-

tery terminals once a week.

(up to a month)

(up to six months)

(up to a year*) 31 BATTERY CHARGING 5 If your Ni-MH battery pack seems to have no capacity, even after being charged, completely discharge it by leaving the power ON overnight. Then, fully charge the battery pack again. If the battery pack still does not retain a charge (or only very little charge), a new battery pack must be purchased. (p. 43) Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. Recommended temperature range for charging:

between +10C and +40C (rapid charge: with BC-191) or between 0C and +45C (regular charge: with BC-192) Use the supplied charger or optional charger (BC-191 for rapid charging, BC-192 for regular charging) only. NEVER use other manufacturers chargers. The battery pack contains a rechargable battery. Charge the battery pack before first operating the transceiver, or when the battery pack becomes exhausted. If you want to prolong the battery life, the following points should be observed:

Avoid over charging. The charging time period by the BC-192 should be less than 48 hours. Use the battery pack until it becomes almost completely ex-

hausted, under normal conditions. We recommend battery charg-

ing after transmitting becomes impossible. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 32 5 BATTERY CHARGING Caution (for the BP-265 Li-ion battery) Misuse of Li-ion batteries may result in the following hazards:

smoke, fire, or the battery may rupture. Misuse can also cause damage to the battery or degradation of battery performance. R DANGER! NEVER short terminals (or charging terminals) of the battery pack. Also, current may flow into nearby metal objects such as a necklace, so be careful when placing battery packs (or the transceiver) in handbags, etc. Simply carrying with or placing near metal objects such as a neck-

lace, etc. may cause shorting. This may damage not only the bat-

tery pack, but also the transceiver. D Battery caution R DANGER! DO NOT hammer or otherwise impact the battery. Do not use the battery if it has been severely impacted or dropped, or if the battery has been subjected to heavy pressure. Battery damage may not be visible on the outside of the case. Even if the surface of the battery does not show cracks or any other damage, the cells inside the battery may rupture or catch fire. R DANGER! NEVER use or leave battery packs in areas with temperatures above +60C (+140F). High temperature buildup in the battery, such as could occur near fires or stoves, inside a sun heated car, or in direct sunlight may cause the battery to rupture or catch fire. Excessive temperatures may also degrade battery per-

formance or shorten battery life. R DANGER! DO NOT expose the battery to rain, snow, seawater, or any other liquids. Do not charge or use a wet battery. If the bat-

tery gets wet, be sure to wipe it dry before using. The battery is not waterproof. 33 BATTERY CHARGING 5 R DANGER! NEVER incinerate used battery packs, since internal battery gas may cause them to rupture, or may cause an explosion. R DANGER! NEVER solder the battery terminals or NEVER mod-

ify the battery pack. This may cause heat generation, and the bat-

tery may rupture, emit smoke or catch fire. R DANGER! Use the battery only with the transceiver for which it is specified. Never use a battery with any other equipment, or for any purpose that is not specified in this instruction manual. R DANGER! If fluid from inside the battery gets in your eyes, blind-

ness can result. Rinse your eyes with clean water, without rubbing them, and see a doctor immediately. R WARNING! Immediately stop using the battery if it emits an ab-

normal odor, heats up, or is discolored or deformed. If any of these conditions occur, contact your Icom dealer or distributor. R WARNING! Immediately wash, using clean water, any part of the body that comes into contact with fluid from inside the battery. R WARNING! NEVER put the battery in a microwave oven, high-

pressure container, or in an induction heating cooker. This could cause a fire, overheating, or cause the battery to rupture. CAUTION: Always use the battery within the specified temperature range, 20C to +60C (4F to +140F). Using the battery out of its specified temperature range will reduce the batterys performance and battery life. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 34 5 BATTERY CHARGING CAUTION: Shorter battery life could occur if the battery is left fully charged, completely discharged, or in an excessive temperature environment (above +50C; +122F) for an extended period of time. If the battery must be left unused for a long time, it must be de-

tached from the radio after discharging. You may use the battery until the remaining capacity is about half, then keep it safely in a cool dry place within the temperature range as shown below:

20C to +50C (4F to +122F) 20C to +35C (4F to +95F) 20C to +20C (4F to +68F)

(up to a month)

(up to three months)

(up to a year) D Charging caution R DANGER! NEVER charge the battery pack in areas with ex-

tremely high temperatures, such as near fires or stoves, inside a sun heated car, or in direct sunlight. In such environments, the safety/protection circuit in the battery will activate, causing the bat-

tery to stop charging. R WARNING! DO NOT charge or leave the battery in the battery charger beyond the specified time for charging. If the battery is not completely charged by the specified time, stop charging and re-

move the battery from the battery charger. Continuing to charge the battery beyond the specified time limit may cause a fire, overheat-

ing, or the battery may rupture. R WARNING! NEVER insert the transceiver (battery attached to the transceiver) into the charger if it is wet or soiled. This could corrode the battery charger terminals or damage the charger. The charger is not waterproof. CAUTION: DO NOT charge the battery outside of the specified temperature range: BC-193 (+10C to +40C; +50F to +104F). Icom recommends charging the battery at +20C (+68F). The bat-

tery may heat up or rupture if charged out of the specified tempera-

ture range. Additionally, battery performance or battery life may be reduced. 35 BATTERY CHARGING 5 Battery chargers D Using the BC-191 to rapid charge the BP-264 The BC-191 provides rapid charging of the Ni-MH battery pack

(BP-264 only). Never use for any other battery pack. Charging time period: Approximately 2 hours (for the BP-264) The following item is additionally required:

An AC adapter (not supplied with some versions) or the DC power cable (OPC-515L/CP-23L). Battery pack Transceiver Turn power OFF AC adapter

(A different type, or no AC adapt-

er is supplied, depending on the version.) Optional OPC-515L*

(for power source) or CP-23L (for 12 V cig-

arette lighter socket) can be used instead of the AC adapter.

About OPC-515L White line:

Black line :

CAUTION: NEVER connect the OPC-515L to a power source using reverse polarity. This will ruin the battery charger. Screws*

( Self tapping screw:

M3.5 at least 30 mm)

*Purchase separately. Using screws is recom-

mended to secure the charger. Status indicator Lights orange:

While charging. Lights green:

Charging is completed. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 36 5 BATTERY CHARGING D Using the BC-192 to regular charge the BP-264 The BC-192 provides regular charging of the Ni-MH battery pack

(BP-264 only). Never use for any other battery pack. Charging time period (with BC-147S): Approximately 16 hours (for the BP-264) The following item is additionally required:

An AC adapter (not supplied with some versions) or the DC power cable (OPC-515L). Battery pack Transceiver Turn power OFF AC adapter

(A different type, or no AC adapt-

er is supplied, depending on the version.) Optional OPC-515L*

(for power source) can be used instead of the AC adapter.

About OPC-515L White line:

Black line :

CAUTION: NEVER connect the OPC-515L to a power source using reverse polarity. This will ruin the battery charger. Charging time period differs depending on the input voltage. 12 V 13.8 V 16 V

: Approx. 36 hours

: Approx. 21 hours

: Approx. 16 hours 37 Screws*

( Self tapping screw:

M3.5 at least 30 mm)

*Purchase separately. Using screws is recom-

mended to secure the charger. Status indicator Lights green while charging. NOTE:

The status indicator will not go out even after a battery pack is fully charged. BATTERY CHARGING 5 D Using the BC-193 to rapid charge the BP-265 The BC-193 provides rapid charging of the Li-ion battery pack

(BP-265 only). Never use for any other battery pack. Charging time period: Approximately 2.5 hours (for the BP-265) The following item is additionally required:

An AC adapter (not supplied with some versions) or the DC power cable (OPC-515L/CP-23L). Battery pack Transceiver Turn power OFF AC adapter

(A different type, or no AC adapt-

er is supplied, depending on the version.) Optional OPC-515L*

(for power source) or CP-23L (for 12 V cig-

arette lighter socket) can be used instead of the AC adapter.

About OPC-515L White line:

Black line :

CAUTION: NEVER connect the OPC-515L to a power source using reverse polarity. This will ruin the battery charger. Screws*

( Self tapping screw:

M3.5 at least 30 mm)

*Purchase separately. Using screws is recom-

mended to secure the charger. Status indicator Lights orange:

While charging. Lights green:

Charging is completed. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 38 5 BATTERY CHARGING D Using the BC-197 to rapid charge the BP-264 or BP-265 The BC-197 rapidly charges up to six battery packs. Charging time for BP-264: Approximately 2 hours Charging time for BP-265: Approximately 2.5 hours The following additional item is required:

An AC adapter (not supplied with some versions) or the DC power cable (OPC-656) Battery pack Transceiver Turn OFF the power Charger adapters* are installed in each slot.

The shape of charger adapter depends on the version of the BC-197. AC adapter

(An AC adapter is not supplied with some versions.) Status indicator

(each indicator independently functions) DC power cable (OPC-656)

(Connect to a DC power supply;

12 to 16 V/at least 7 A) Red line : + Black line : _ 39 BATTERY CHARGING 5 There are two types of BC-197 chargers for the IC-F3100D series or IC-F4100D series; one is for Ni-MH batteries, and the other is for Li-ion batteries. Before you purchase a BC-197, check the type of battery you are using, and then be sure to choose the suitable charger. BC-197 Charger Type Chargeable Battery With AD-120* charger adapters BP-264 Ni-MH battery With AD-121* charger adapters BP-265 Li-ion battery

* The type of the charger adapter, AD-120 or AD-121 is printed on the inside bottom of the charger adapter, and the type of battery it holds is printed on the top right corner of the adapter. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 40 5 BATTERY CHARGING IMPORTANT:

Ensure the tabs on the battery pack are correctly aligned with the guide rails inside the charger. Tabs BC-191, BC-192, BC-193 Guide rail 41 BATTERY CASE Optional battery case (BP-263) When using the optional battery case, install 6 AA (LR6) size alkaline batteries, as illustrated below. 6 q Remove the battery case, if it is attached. (pp. 3, 4) w Install 6 AA (LR6) size alkaline batteries. Install only alkaline batteries. Be sure to observe the correct polarity. Be careful! The negative terminals of the battery case protrude from the body, so pay attention not to injure your fingers when inserting the batteries. e Attach the battery case. (pp. 3, 4) CAUTION:

When installing batteries, make sure they are all the same brand, type and capacity. Also, do not mix new and old batter-

ies together. Keep the battery terminals clean. Its a good idea to clean the battery terminals once a week. Never incinerate used battery cells since internal battery gas may cause them to rupture. Never expose a detached battery case to water. If the battery case gets wet, be sure to wipe it dry before using it. Never use batteries whose insulated cover is damaged. NOTE: When the optional battery case is attached, the battery type must be selected as Battery case operation when turning the transceiver ON. Ask your dealer for details. (p. 12) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 42 7 OPTIONS D BATTERY PACK Battery pack Voltage BP-263 Capacity Battery case for AA (LR6) 6 alkaline BP-264 7.2 V 1400 mAh (typ.) BP-265 7.4 V 1900 mAh (min.) 2000 mAh (typ.) Battery life*1

*2 VHF UHF VHF UHF 12 hrs. 11.3 hrs. 17.5 hrs. 16.1 hrs.

*1 When the power save function is turned ON, and the operating time is calculated under the following conditions;

TX : RX : standby = 5 : 5 : 90

*2 The average operating time depends on the alkaline cells used. D BELT CLIPS MB-124 beLt cLip Exclusive alligator-type belt clip. D CHARGERS BC-191 desktop charger + BC-123S ac adapter For rapid charging of the Ni-MH battery pack. An AC adapter is supplied with the charger, depending on the version. Charging time period: approximately 2 hours for the BP-264. BC-192 desktop charger + BC-147S ac adapter For regular charging of the Ni-MH battery pack. An AC adapter is supplied with the charger, depending on the version. Charging time period: approximately 16 hours for the BP-264. BC-193 desktop charger + BC-123S ac adapter For rapid charging of the Li-ion battery pack. An AC adapter is supplied with the charger, depending on the version. Charging time period: approximately 2.5 hours for the BP-265. 43 OPTIONS 7 BC-197 muLti-charger For rapid simultaneously charging of up to six battery packs. An AC adapter may be supplied with the charger, depending on the version. There are two types of BC-197 chargers for the IC-F3100D/

IC-F4100D series. BC-197 Charger Type Chargeable Battery Charging time Approx. 2 hrs. BP-264 Ni-MH battery BP-265 Li-ion battery Approx. 2.5 hrs. With AD-120*

With AD-121*

* Either AD-120 or AD-121 charger adapters are installed in the BC-

197, depending on the chargeable battery pack. D DC POWER CABLES CP-23L cigarette Lighter cabLe Allows charging of the battery pack through a 12 V cigarette lighter socket. (For BC-191/BC-193) OPC-515L/OPC-656 dc power cabLe For charging of the battery packs using a 12 V DC power source instead of the AC adapter.

(OPC-515L for BC-191/BC-192/BC-193: OPC-656 for BC-197) D ANTENNAS FA-SC73US/FA-SC56VS/FA-SC57VS stubby antennas FA-SC73US : 450490 MHz FA-SC57VS : 160174 MHz FA-SC25U/FA-SC57U/FA-SC72U/

FA-SC56VS : 150162 MHz FA-SC25V/FA-SC55V antennas

: 400430 MHz

: 470520 MHz

: 146174 MHz FA-SC25U FA-SC72U FA-SC55V FA-SC61VC/FA-SC61UC cut antennas FA-SC61VC : 136174 MHz FA-SC57U FA-SC25V

: 430470 MHz

: 136155 MHz FA-SC61UC : 380520 MHz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 44 7 OPTIONS D OTHER OPTIONS AD-98FSC antenna connector converter Allows you to connect an external antenna with a BNC connector. HM-158L/HM-159L speaker-microphone Combination speaker-microphone that provides convenient op-

eration while hanging the transceiver on your belt.

: Ear hook type

: Neck-arm type

: Throat microphone HM-171GP speaker-microphone GPS speaker-microphone for BIIS and Digital modes operation. HS-94/HS-95/HS-97 headset + OPC-2004 pLug adapter cabLe HS-94 HS-95 HS-97 OPC-2004 : Allows you to connect the HS-94/HS-95/HS-97 to the transceiver. After connection, the VOX function can be used. SP-27 tube earphone Provides clear audio in noisy environments. Approved Icom optional equipment is designed for optimal performance when used with an Icom transceiver. Icom is not responsible for the destruction or damage to an Icom trans-

ceiver in the event the Icom transceiver is used with equipment that is not manufactured or approved by Icom. Some options may not be available in some countries. Please ask your dealer for details. 45 OPTIONS 7 VOX function The transceiver has a VOX function, which allows you hands-free operation. An optional headset (HS-94/HS-95/HS-97) and a plug adapter cable (OPC-2004) are additionally required for operation. The VOX (voice operated transmission) function starts transmitting when you speak into the microphone, without needing to push the PTT switch; then, automatically returns to receive when you stop speak-

ing. D Optional unit connection q Rotate [VOL] to turn the transceiver power OFF. w Remove the jack cover. (p. 4) e Connect the optional headset (HS-94, HS-95 or HS-97) and OPC-2004 as described below. OPC-2004

[VOL]

HS-94 w q e 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 46 7 OPTIONS D Turning the VOX function ON or OFF The VOX function can be turned ON or OFF when turning the trans-

ceiver power ON. q Rotate [VOL] to turn the trans-

ceiver power OFF. w Set [ROTARY SELECTOR] to any channel other than Chan-

nel 16. e While holding down [PTT] and

[Upper], rotate [VOL] to turn ON the power to switch the VOX function ON or OFF. One beep sounds when the VOX function is turned OFF. Two beeps sound when the VOX function is turned ON.

[ROTARY SELECTOR]

[VOL]

[PTT]

[Upper]

NOTE: This operation may not be available, depending on the presetting. Ask your dealer for details. 47 D Setting the VOX gain The VOX sensitivity level can be adjusted from 1 (minimum) to 10

(maximum). OPTIONS 7

[ROTARY SELECTOR]

[VOL]

[PTT]

[Upper]

q Connect the optional headset

(HS-94, HS-95 or HS-97) and OPC-2004. (p. 46) w Rotate [VOL] to turn the trans-

ceiver power OFF. e Set [ROTARY SELECTOR] to Channel 16. r While holding down [PTT] and

[Upper], rotate [VOL] to turn ON the power and enter the VOX gain adjustment mode. t Push [Upper] to increase, or push [Lower] to decrease the VOX gain while speaking into the optional headset. The adjustable range is 1 (mini-

mum) to 10 (maximum). A beep sounds after pushing [Upper] or [Lower]. If the level is set on 1 or 10, an error beep sounds after pushing. Therefore, you can determine the current level setting by the type of beep that sounds. y Rotate [VOL] to turn the power OFF, then ON to exit the VOX gain adjustment mode. NOTE:

This operation may not be available, depending on the preset-

ting. Ask your dealer for details. Set the microphone gain before setting the VOX gain. (p. 18) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 48 8 SAFETY TRAINING INFORMATION W ARNING Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as Occupational Use Only, meaning it must be used only during the course of employment by indi-

viduals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the General Population in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for Occupational Use Only. In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans:

FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Fre-

quency Electromagnetic Fields, 3 kHz to 300 GHz. American National Standards Institute (C95.3-1992), IEEE Recom-

mended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields RF and Microwave. The accessories (antennas, batteries, belt clips, speaker-micro-

phone, etc. that is listed on pages 4345) are authorized for use with this product. Use of accessories other than those specified may result in RF exposure levels exceeding the FCC requirements for wireless RF exposure. To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occu-

pational use, always adhere to the following guide-

lines:

CAU TION 49 SAFETY TRAINING INFORMATION 8 DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio. DO NOT transmit for more than 50% of total radio use time (50%

duty cycle). 50% duty cycle is also applicable to VOX/PTT mode. Transmitting more than 50% of the time can cause FCC RF expo-

sure compliance requirements to be exceeded. The radio is trans-

mitting when the LED indicator lights red. You can cause the radio to transmit by pressing the PTT switch or VOX function. ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the Icom belt-clip which is listed on page 43 when attaching the radio to your belt, etc., to en-

sure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound qual-

ity, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to as-

sure that this radio operates with the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electro-

magnetic radiation such as hospitals, aircraft, and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 50 MEMO MEMO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 MEMO MEMO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 A-6884D-1EX Printed in Japan 2010 Icom Inc. Printed on recycled paper with soy ink. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan