FCC ID: AFJ352201 UHF Transeiver

FA-SC61UC Antenna Cutting Chart Antenna cap 360 MHz 380 MHz 400 MHz 420 MHz 440 MHz 460 MHz 480 MHz 500 MHz 520 MHz Thank you for purchasing the FA-SC61UC UHF ANTENNA. Please read these instructions thoroughly before using the FA-SC61UC. FA-SC61UC The optimum bandwidth is 8%

of the tuned frequency. For optimum performance tune to the center transmit frequency of the radio. Cutting Instructions q Align the bottom of the anten-

na onto the 0 position of the cutting guide diagram at left. w Mark the antenna at the length corresponding to the desired to be tuned. frequency e Cut the antenna to the marked length. Use a wire cutter that can cut at least 1.2 mm (d) of piano wire. r Apply adhesive to the top of the antenna and attach the supplied antenna cap. Use of Cemedine Co. Super-X No. 8008 black

(Icom number:

8950002910) or similar is recommended. parts NOTE:

Antenna cap must be inser ted after cutting the element otherwise water immersion makes the element damaged. Center frequency

(MHz) 360 380 400 420 440 460 480 500 520 Length

(mm) 185 175 165 156 148 142 136 129 125 0 CAUTION:

Making antenna cuts at other than the prescribed lengths specified could void the user's authority to operate the equipment. A-6532K-1EX-w Printed in Japan 2006-2009 Icom Inc.

INSTRUCTION MANUAL VHF TRANSCEIVERS iF3230D Series UHF TRANSCEIVERS iF4230D Series This device complies with Part 15 of the FCC Rules. Opera-

tion is subject to the condition that this device does not cause harmful interference. The photo shows the VHF transceiver (S type) IMPORTANT READ ALL INSTRUCTIONS carefully and com-

pletely before using the transceiver. SAVE THIS INSTRUCTION MANUAL This instruction manual contains important oper ating instructions for the IC-F3230DT, IC-F3230DS VHF TRANSCEIVERS and the IC-F4230DT, IC-F4230DS UHF TRANSCEIVERS. See the operating guide for details of IDAS (ICOM Digital Advanced System) system operations. Ask your dealer for details. EXPLICIT DEFINITIONS WORD RDANGER!

RWARNING!

CAUTION NOTE DEFINITION Personal death, serious injury or an ex-

plosion may occur. Personal injury, fire hazard or electric shock may occur. Equipment damage may occur. If disregarded, inconvenience only. No risk of personal injury, fire or electric shock. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incor-

porated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. i PRECAUTIONS R DANGER! NEVER short the terminals of the bat-

tery pack. R DANGER! Use and charge only specified Icom bat-

tery packs with Icom radios or Icom chargers. Only Icom bat-

tery packs are tested and approved for use with Icom radios or charged with Icom chargers. Using third-party or coun-

terfeit battery packs or chargers may cause smoke, fire, or cause the battery to burst. R WARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 inches) away from the lips and the transceiver is vertical. R WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. Hearing experts advise against continuous high volume op-

eration. If you experience a ringing in your ears, reduce the volume level or discontinue use. R WARNING! NEVER operate the transceiver while driving a vehicle. Safe driving requires your full attention anything less may result in an accident. CAUTION: MAKE SURE the flexible antenna, bat-

tery pack and jack cover are securely attached to the trans-

ceiver, and that the antenna and battery pack are dry before attachment. Exposing the inside of the transceiver to dust or water will result in serious damage to the transceiver. DO NOT operate the transceiver near unshielded electri-

cal blast ing caps or in an explosive atmosphere. DO NOT push [PTT] when not actually intending to transmit. DO NOT use or place the transceiver in direct sunlight or in areas with temperatures below 30C (22F) or above

+60C (+140F). The basic operations, transmission and reception of the trans-

ceiver are guaranteed within the specified operating tempera-

ture range. However, the LCD display may not be operate correctly, or show an indication in the case of long hours of operation, or after being placed in extremely cold areas. DO NOT modify the transceiver. The transceiver warranty does not cover any problems caused by unauthorized modi-

fication. DO NOT use harsh solvents such as benzine or alcohol when cleaning, as they will damage the transceiver surfaces. BE CAREFUL! The transceiver will become hot when operating it continuously for long periods of time. ii PRECAUTIONS (Continued) BE CAREFUL! The transceiver meet IP67* require-

ments for dust-tight and waterproof protection. However, once the transceiver has been dropped, dust-tight and waterproof protection cannot be guaranteed because of possible dam-

age to the transceivers case or the waterproof seal.

* Only when the jack cover or the optional HM-168LWP is attached. Even when the transceiver power is OFF, a slight current still flows in the circuits. Remove the battery pack or batteries from the trans ceiver when not using it for a long time. Otherwise, the installed battery pack or batteries will become exhausted, and will need to be recharged or replaced. MAKE SURE to turn the transceiver power OFF before connect ing the supplied/optional equipment. FCC INFORMATION FOR CLASS A UNINTENTIONAL RADIATORS:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communi-

cations. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAUTION: Changes or modifications to this transceiver, not expressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations. iii TABLE OF CONTENTS IMPORTANT .......................................................................... i EXPLICIT DEFINITIONS ....................................................... i PRECAUTIONS .................................................................... ii FCC INFORMATION ........................................................... iii TABLE OF CONTENTS ....................................................... iv 1 ACCESSORIES ...........................................................12

...................................................1

................................................1 Supplied accessories Accessory attachments 2 PANEL DESCRIPTION ................................................37

...................................................................3

...........................................................4

........................................5 Front panel Function display Programmable function keys 3 BASIC OPERATION ..................................................811

........................................................8

........................................................9

.........................................10

............................................................11

........................................11 Turning power ON Channel selection Receiving and transmitting User set mode Priority A channel selection 4 BATTERY CHARGING ............................................1216

.......................................................................12

.........................................................13 Caution Battery chargers 5 BATTERY CASE ......................................................1719

.....................................17

.....................................18 BP-240 optional battery case BP-261 optional battery case 6 SPEAKER MICROPHONE ............................................20

..............................20

....................................................................20 Optional HM-168LWP description Attaching 7 OPTIONAL SWIVEL BELT CLIP ............................2122

..........................................................21

....................................................................21

...................................................................22 MB-93 contents Attaching Detaching 8 OPTIONS .................................................................2324 9 SAFETY TRAINING INFORMATION .......................2526 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 iv 1 ACCESSORIES Supplied accessories NOTE: Some accessories are not supplied, depending on the transceiver version. Battery pack Battery charger*

Belt clip AC adapter*

(for the battery charger) Flexible antenna*

(This illustration is of the VHF type.)

*Not supplied, or the shape is different, depending on the trans-

ceiver version. Accessory attachments Flexible antenna D Connect the supplied flexible antenna to the antenna connector. CAUTION:

NEVER carry the transceiver by holding only the antenna. DO NOT connect an antenna other than those listed on page 24. Transmitting without an antenna may damage the transceiver. 1 Battery pack D To attach the battery pack:

Slide the battery pack in the direction of the arrow (q) until the battery release button makes a click sound. NOTE: Push on the bottom of the pack to make sure the release button is firmly locked. To release the battery pack:

Slide the battery release button in the direction of the arrow

(w) as shown below. The battery pack is then released. NEVER release or attach the battery pack when the trans-

ceiver is wet or soiled. This may result water or dust getting into the transceiver/battery pack and may result in the transceiver being damaged. q w Battery release button NOTE: Keep battery terminals clean. Its a good idea to occasionally clean them. Belt clip D To attach the belt clip:

q w Slide the belt clip in the direction of the arrow until the belt Remove the battery pack if it is attached. clip is locked and makes a click sound. To detach the belt clip:

q w Remove the battery pack if it is attached. Pinch the clip (

the arrow (w). q), and slide the belt clip in the direction of w q ACCESSORIES 1 Jack cover D To attach the jack cover:

q w Attach the jack cover to the [MIC/SP] jack. (

Tighten the screws. (

w) q)

[MIC/SP] jack q w Jack cover CAUTION:

Attach the jack cover when the optional equipment is not used. Use only the supplied screws. To detach the jack cover:

q Unscrew the screws using a phillips screwdriver. (q) Detach the jack cover to connect the optional equipment. (w) w q q w 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 2 2 PANEL DESCRIPTION Front panel q w e r t o i Speaker Microphone u y y DEALER-PROGRAMMABLE KEYS [P0] to [P3]

Desired functions can be independently programmed by your dealer. (p. 5) u FUNCTION DISPLAY (p. 4) Displays a variety of information such as an operating channel number, channel name, User Set mode contents, and so on. i EXTERNAL MICROPHONE/SPEAKER JACK Connect an optional equipment. NOTE: Connect or disconnect the optional equipment after the transceiver is turned OFF. q ANTENNA CONNECTOR Connects the supplied antenna. w DEALER-PROGRAMMABLE KEY [Emer]

A desired function can be programmed by your dealer. (p. 5) e DEALER-PROGRAMMABLE KEY [Side1]

A desired function can be programmed by your dealer. (p. 5) r PTT SWITCH [PTT]

Hold down to transmit, release to receive. t DEALER-PROGRAMMABLE KEYS [Side2]/[Side3]

Desired functions can be independently programmed by your dealer. (p. 5) 3 Jack cover NOTE: Attach the jack cover when optional equipment is not used. See (p. 2) for details. o VOLUME CONTROL [VOL]

Rotate to turn the power ON or OFF and to adjust the au-

dio level. Function display q trew y u i t AUDIBLE ICON PANEL DESCRIPTION 2 o

!0 In the analog mode, appears when the CTCSS (DTCS) squelch mute is released while holding down [Monitor]. In the digital mode, appears while holding down [Moni-

tor]. y ENCRYPTION ICON In the digital mode, appears when the encryption function is activated. u BELL ICON In the digital mode, appears/blinks when an SDM (Short Data Message), Status Call or Call Alert is received, de-

pending on the preprogramming. i KEY LOCK ICON Appears when the Key lock function is ON. o BATTERY ICON Appears or blinks when the battery power decreases to a specified level.

!0 ALPHANUMERIC DISPLAY Displays an operating channel number, channel name, User Set mode contents, and so on. q TRANSMIT ICON Appears while transmitting. w BUSY ICON Appears while the channel is busy (receiving). e SIGNAL STRENGTH ICON Shows the relative receive signal strength level. Weak Receive Signal level Strong About icon for the Trunking mode Disappears while in a no service area. Blinks while registering to a repeater. Appears when registration is completed. r LOW POWER ICON Appears when low output power is selected. When the battery power decreases to a specified level, low power is automatically selected. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 4 2 PANEL DESCRIPTION Programmable function keys The following functions can be assigned to [Emer], [Side1],

[Side2], [Side3], [P0], [P1], [P2] and [P3] programmable function keys. Consult your Icom dealer or system operator for details con-

cerning your transceivers programming. CH UP AND DOWN As described in the following topics, after pushing a pro-

grammed key, push [CH Up] or [CH Down] to select an op-

tion, setting, and so on. ZONE Push this key, then select the desired zone using [CH Up]/

[CH Down]. What is a zone? Certain channels are grouped to-

gether and assigned to a zone, according to their intended use. For example, Staff A and Staff B are assigned to a Business zone, and John and Cindy are assigned to a Private zone. 5 SCAN START/STOP Push to start and cancel a scan. When a scan is started with the Power ON Scan or Automatic scan function, push this key to cancel it. The cancelled scan re-

sumes after a preprogrammed time period. Hold down this key for 1 second to display the scan group, then push [CH Up] or [CH Down] to select the desired group. SCAN ADD/DEL (TAG) Push to add the channel to, or delete it from, the current scan group. 1. Push to display the scan group, then push [CH Up] or [CH Down]

to select the desired one. 2. Push to add the channel to, or delete it from, the selected scan group. 3. Hold down for 1 second to exit the scan list selection mode. While a scan is paused on a non-priority channel, push this key to delete the selected channel from the scan group. Depending on the setting, the cleared channel may be automatically added to the scan group again after the scan is cancelled. PANEL DESCRIPTION 2 PRIORITY A CHANNEL, PRIORITY B CHANNEL Push to select the Priority A or Priority B channel. LOCK PRIORITY A CHANNEL (REWRITE), PRIORITY B CHANNEL (REWRITE) Push to select the Priority A or Priority B channel. Hold down [Prio A (Rewrite)] or [Prio B (Rewrite)] for 1 second to assign the operating channel to Priority A or Priority B channel, respectively. Hold down this key until LOCK ON is displayed to elec-

tronically lock all programmable keys except the following:

[Moni], [Lock], [Emergency]*, [Surveillance], [Siren], [Lone Worker]*, [Light] and [Shift].

* For digital operation. See the operating guide for details To turn OFF the Key Lock function, hold down this key until LOCK OFF is displayed. MEMORY CHANNELS 1, 2, 3, 4 Push to directly select memory channel 1, 2, 3 or 4, if pro-

grammed. Consult your dealer for details. MONITOR Push to turn the CTCSS (DTCS) squelch mute ON or OFF. LIGHT Push to turn ON the backlight for about 5 seconds, when the backlight function is set to OFF in the User Set mode. HIGH/LOW Push to select the transmit output power temporarily or per-

manently, depending on the preprogramming. Ask your dealer for the output power level for each selection. TALK AROUND Push to turn the Talk Around function ON or OFF. The Talk Around function equalizes the transmit frequency to the receive frequency for transceiver-to-transceiver communication. WIDE/NARROW Push to toggle the IF bandwidth between wide and narrow. SURVEILLANCE Push to turn the surveillance function ON or OFF. When this function is turned ON and a signal is received, the beep is not heard and the LED does not light, even if a key is pushed. 2 6 SHIFT Push to toggle the Normal mode key functions and the Shift mode key functions. When the Shift mode is selected, the display briefly shows SHIFT ON. When the Normal mode is selected, the display briefly shows SHIFT OFF. 2 PANEL DESCRIPTION Programmable function keys (Continued) SIREN Hold down for 1 second to sound the siren. This function can be used for situations other than an emer-

gency alert, such as a security alarm for example. The siren can be stopped only by turning OFF the transceiver power. USER SET MODE Hold down for 1 second to enter the User Set mode. While in the User Set mode, push this key to select an item*, and change the value or setting by pushing [CH Up] or [CH Down].

* Selectable items may differ, depending on the preprogram-

ming. Hold down this key for 1 second again to exit the User Set mode. ANNOUNCE Push to turn the Channel Announce function ON or OFF. When this function is turned ON, the transceiver announces the channel number when it is selected. RESET Push to return to the normal operating mode. While in the audible mode, push to return to the inaudible mode. NOTE: See the operating guide for the [Reset] key opera-

tion in the digital mode. 7 Turning power ON Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation.

(p. 12) Rotate [VOL] to turn ON the power. q w If the transceiver is programmed for a start up password, input the digit codes as directed by your dealer. The 10-keypad may be used for password input, depending on the transceivers version:

The keys in the table below can be used for password input. The transceiver detects numbers in the same block as identical. Therefore 01234 and 56789 are the same. BASIC OPERATION 3 Battery type selection D The battery type must be selected according to the attached battery type when turning ON the transceiver. Ask your dealer for details. q w Turn OFF the power. While pushing and holding [Emer] and [PTT], turn ON the power by rotating [VOL] to toggle the attached battery type. After the display appears, release [Emer] and [PTT]. DRY BATT is displayed for about 3 seconds then L appears when the battery case use is selected. In this case, the transmit output power is low. LI-ION is displayed for about 3 seconds when the Lithium-ion battery use is selected.

[VOL]

[Side3]

[P0]/[P1]/

[P2]/[P3]

KEY Side3 NUMBER 0 5 1 6 2 7 3 8 4 9

[VOL]

[Emer]

[PTT]

Appears Dry battery mode e When the PASSWORD indication does not clear after in-

putting 4 digits, the input code number may be incorrect. Turn the power off and start over in this case. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 8 AUTOMATIC SCAN TYPE:

Channel setting is not necessary for this type. When turning ON the power, the transceiver automatically starts scanning. Scanning stops when a signal is received. NOTE: If the Move to Priority A channel at Power ON func-

tion is turned ON, the transceiver selects the Priority A channel at Power ON, and then starts scanning. (p. 11) 3 BASIC OPERATION Channel selection Several types of channel selections are available. Methods may differ, depending on your system set up. NON-ZONE TYPE:

To select the desired operating channel:

Push [CH Up] or [CH Down]. Push one of [MR-CH 1] to [MR-CH 4]. Push one of these keys, [Prio A], [Prio B], [Prio A (Re-

write)] or [Prio B (Rewrite)]. ZONE TYPE:

To select the desired operating channel:

Push [Zone], then push [CH Up] or [CH Down]. VOTING OPERATION:

The transceiver automatically starts scanning when a zone, specified for the voting operation, is selected. The voting scan detects the S-meter of the repeater and au-

tomatically selects the strongest station. 9 Receiving and transmitting CAUTION: Transmitting without an antenna may damage the transceiver. See page 1 for accessory attachments. Receiving:

q w Rotate [VOL] to turn ON the power. Push [CH Up] or [CH Down] to sequentially select the con-

ventional system channel. e When receiving a call, adjust the audio output level to a comfortable listening level. Transmitting:

Wait for the channel to become clear to avoid interference. q While pushing and holding [PTT], speak into the micro-

phone at a normal voice level. Release [PTT] to return to receive. w IMPORTANT: To maximize the readability of your signal;

1. Pause briefly after pushing [PTT]. 2. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak at a normal voice level. BASIC OPERATION 3 Transmitting notes D Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions:

- The channel is busy. However, depending on the pre-

programmed settings, you can transmit when the call includes an unmatching (or matching) CTCSS (DTCS), RAN code*, or Individual or Talkgroup ID*.

* Digital operation only

- The selected channel is a receive only channel. Time-out timer If continuous transmission exceeds the preprogrammed time-out timer limit, the transmission is cut off. Penalty timer After the transmission is cut off by the time-out timer, trans-

mission is further inhibited for the preprogrammed penalty timer period. 3 10 3 BASIC OPERATION User set mode The User Set mode allows you to set seldom-changed set-

tings. If the transceiver has [User Set Mode] assigned to it, you can customize the transceiver operation to suit your preferences and operating style. Entering the User Set mode:

q Hold down [User Set Mode] for 1 second to enter the User Set mode. Push [User Set Mode] several times to select the appro-

priate item. Then push [CH Up] or [CH Down] to set the desired level or condition. Selectable Set mode items are Backlight, Beep ON/OFF, Beep Level, Ringer Level, SQL Level, AF Min Level, Mic Gain, Battery Voltage, Signal Moni, Lone Worker and System Info. Hold down [User Set Mode] for 1 second again to exit the User Set mode. w e Priority A channel selection When one of the following operations is performed, the trans-

ceiver automatically selects Priority A channel. Turning ON the power Priority A channel is selected each time the transceivers power is turned ON. Auto Reset Priority A channel is selected when the Auto Reset timer ends. OFF hook Priority A channel is selected when you take the micro-

phone OFF hook. 11 Caution Misuse of Lithium-ion batteries may result in the following hazards: smoke, fire, or the battery may rupture. Misuse can also cause damage to the battery or degradation of battery performance. R DANGER! Use and charge only specified Icom battery packs with Icom radios or Icom charger. Only Icom battery packs are tested and approved for use and charge with Icom radios or Icom charger. Using third-party or counterfeit battery packs or charger may cause smoke, fire, or cause the battery to burst. Battery caution D R DANGER! DO NOT hammer or otherwise impact the battery. Do not use the battery if it has been severely impacted or dropped, or if the battery has been subjected to heavy pressure. Battery damage may not be visible on the outside of the case. Even if the surface of the battery does not show cracks or any other damage, the cells inside the battery may rupture or catch fire. R DANGER! NEVER use or leave battery packs in areas with temperatures above +60C (+140F). High temperature buildup in the battery, such as could occur near fires or stoves, inside a sun heated car, or in direct sunlight may cause the battery to rupture or catch fire. Excessive temperatures may also degrade battery performance or shorten battery life. R DANGER! DO NOT expose the battery to rain, snow, seawa-

ter, or any other liquids. Never charge or use a wet battery. If the battery gets wet, be sure to wipe it dry before using. BATTERY CHARGING 4 R DANGER! NEVER incinerate used battery packs since inter-

nal battery gas may cause them to rupture, or may cause an explosion. R DANGER! NEVER solder the battery terminals or NEVER modify the battery pack. This may cause heat generation, and the battery may rupture, emit smoke or catch fire. R DANGER! Use the battery only with the transceiver for which it is specified. Never use a battery with any other equipment, or for any purpose that is not specified in this instruction manual. R DANGER! If fluid from inside the battery gets in your eyes, blindness can result. Rinse your eyes with clean water, without rubbing them, and see a doctor immediately. R WARNING! Immediately stop using the battery if it emits an abnormal odor, heats up, or is discolored or deformed. If any of these conditions occur, contact your Icom dealer or distributor. R WARNING! Immediately wash, using clean water, any part of the body that comes into contact with fluid from inside the battery. R WARNING! NEVER put the battery in a microwave oven, high-

pressure container, or in an induction heating cooker. This could cause a fire, overheating, or cause the battery to rupture. CAUTION: Always use the battery within the specified tempera-

ture range, 20C to +60C (4F to +140F). Using the battery out of its specified temperature range will reduce the batterys performance and battery life. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 12 4 BATTERY CHARGING CAUTION: Shorter battery life could occur if the battery is left fully charged, completely discharged, or in an excessive temper-

ature environment (above +50C; +122F) for an extended period of time. If the battery must be left unused for a long time, it must be detached from the radio after discharging. You may use the battery until the remaining capacity is about half, then keep it safely in a cool dry place with the temperature range as below:

20C to +50C (4F to +122F) 20C to +35C (4F to +95F)

(within a month)

(within three months) Charging caution D R DANGER! NEVER charge the battery pack in areas with extremely high temperatures, such as near fires or stoves, inside a sun heated car, or in direct sunlight. In such environments, the safety/protection circuit in the battery will activate, causing the battery to stop charging. R WARNING! NEVER charge or leave the battery in the bat-

tery charger beyond the specified time for charging. If the battery is not completely charged by the specified time, stop charging and remove the battery from the battery charger. Continuing to charge the battery beyond the specified time limit may cause a fire, overheating, or the battery may rupture. R WARNING! NEVER insert the transceiver (battery attached to the transceiver) into the charger if it is wet or soiled. This could corrode the battery charger terminals or damage the charger. The charger is not waterproof. CAUTION: NEVER charge the battery outside of the specified tem-

perature range: BC-160/BC-171 (0C to +45C; +32F to +113F). BC-

119N/BC121N/BC-197 (+10C to +40C; +50F to +104F). Icom rec-

ommends charging the battery at +20C (+68F). The battery may heat up or rupture if charged out of the specified temperature range. Additionally, battery performance or battery life may be reduced. 13 Battery chargers Rapid charging with the BC-160 D The optional BC-160 rapidly charges the Li-ion battery pack. An AC adapter (may be supplied with BC-160, depending on the version) or the DC power cable (OPC-515L/CP-23L) is additionally required. Battery pack Transceiver Turn power OFF AC adapter

(Not supplied with some versions.)

Optional OPC-515L

(for 13.8 V power source) or CP-23L

(for 12 V cigarette lighter socket) can be used instead of the AC adapter.

CAUTION: NEVER connect the OPC-

515L to a power source using reverse polarity. This will ruin the battery charger. White line: Black line :

BATTERY CHARGING 4 AD-106 installation D The AD-106 charger adapter must be installed into the BC-

119N or BC-121N before battery charging. Connect the AD-106 charger adapter and the BC-119N/

BC-121N as ahown below, then install the AD-106 into the holder space of the BC-119N or BC-121N with the sup-

plied screws. Turn power OFF AD-106 Connectors Screws supplied with the charger adapter Plugs Regular charging with the BC-171 D The optional BC-171 regularly charges the Li-ion battery pack. An AC adapter (may be supplied with BC-171, depending on the version) or the DC power cable (OPC-515L/CP-23L) is additionally required. Transceiver Battery pack AC adapter

(Not supplied with some versions.)

Optional OPC-515L

(for 13.8 V power source) or CP-23L

(for 12 V cigarette lighter socket) can be used instead of the AC adapter.

CAUTION: NEVER connect the OPC-

515L to a power source using reverse polarity. This will ruin the battery charger. White line: Black line :

* This illustration is of the BC-119N. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 14 4 BATTERY CHARGING Rapid charging with the BC-119N+AD-106 D The optional BC-119N rapidly charges the Li-ion battery pack. The following items are additionally required. AD-106 charger adapter An AC adapter (may be supplied with the BC-119N, de-

pending on the version) or the DC power cable (OPC-515L/

CP-23L). Transceiver Turn power OFF AC adapter

(Not supplied with some versions.) Battery pack Rapid charging with the BC-121N+AD-106 D The optional BC-121N can simultaneously charge up to 6 Li-ion battery packs. The following items are additionally re-

quired. Six AD-106 charger adapters An optional AC adapter or the DC power cable (OPC-656) Transceiver Turn power OFF Battery pack AC adapter

(Purchased separately) AD-106 charger adapters are installed in each slot. AD-106 charger adapter is installed in BC-119N.

Optional OPC-515L

(for 13.8 V power source) or CP-23L

(for 12 V cigarette lighter socket) can be used instead of the AC adapter.

CAUTION: NEVER connect the OPC-

515L to a power source using reverse polarity. This will ruin the battery charger. White line: Black line :

15 DC power cable (OPC-656)

(Connect with the DC power supply; 13.8 V/at least 7 A)

*Abou the OPC-656 Red line : Black line :

Rapid charging with the BC-197 D The optional BC-197 can simultaneously charge up to 6 Li-ion battery packs. The following items are additionally required. An optional AC adapter (not supplied with some versions) or the DC power cable (OPC-656) IMPORTANT: Battery charging caution Ensure the guide tabs on the battery pack are correctly aligned with the guide rails inside the charger adapter.

(This illustration is of the BC-160.) BATTERY CHARGING 4 Battery pack Turn OFF the power Transceiver The charger adapters are in-

stalled in each slot. The shape of charger adapter depends on the version of the BC-197. AC adapter

(No AC adapt-

er is supplied, depending on the version.) Tabs Status indicator

(each indicator independently functions) Guide rail OPC-656 (DC power cable)

(Connect to a DC power supply;

12 to 16 V/at least 7 A) Red line : + Black line : _ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 16 5 BATTERY CASE BP-240 optional battery case When using the BP-240 battery case, install six AAA (LR03) size alkaline batteries, as illustrated to the right. The BP-240 is constructed to the IPX4 waterproof standard. q w e q), and open the Unhook the battery cover release hook (

cover in the direction of the arrow (w). (Fig.1) Install six AAA (LR03) size alkaline batteries. (Fig.2) Install only alkaline batteries. Be sure to observe the correct polarity. Replace the cover in the direction of the arrow (

e), then close (r). Push the battery cover release hook until it makes a click sound (t). (Fig.3) CAUTION:

When installing the batteries, make sure they are all the same brand, type and capacity. Also, do not mix new and old batteries together. Keep battery terminals clean. Its a good idea to occa-

sionally clean them. Never incinerate used battery cells since internal battery gas may cause them to rupture. Never expose a detached battery case to water. If the bat-

tery case gets wet, be sure to wipe it dry before using it. NOTE: When the optional battery case is attached, the battery type must be set to DRY BATT when turning ON the transceiver. (p. 8) 17 Fig.1 Fig.2 Fig.3 w BP-240 q e r t BP-261 optional battery case Alkaline batteries installation D Install six AA (LR6) size alkaline batteries as described below. The BP-261 is constructed to the IPX4 waterproof standard. q w e q), and open the Unhook the battery cover release hook (

cover in the direction of the arrow (w). (Fig.1) Install six AA (LR6) size alkaline batteries. (Fig.2) Install only alkaline batteries. Be sure to observe the correct polarity. Replace the cover in the direction of the arrow (

e), then close (r). Push the battery cover release hook until it makes a click sound (t). (Fig.3) CAUTION:

When installing the batteries, make sure they are all the same brand, type and capacity. Also, do not mix new and old batteries together. Keep battery terminals clean. Its a good idea to occa-

sionally clean them. Never incinerate used battery cells since internal battery gas may cause them to rupture. Never expose a detached battery case to water. If the bat-

tery case gets wet, be sure to wipe it dry before using it. NOTE: When the optional battery case is attached, the battery type must be set to DRY BATT when turning ON the transceiver. (p. 8) BATTERY CASE 5 BP-261 w q Fig.1 Fig.2 e r Fig.3 t 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 18 5 BATTERY CASE BP-261 optional battery case (Continued) Attaching D Slide the battery pack in the direction of the arrow until the battery release button makes a click sound. Detaching D Slide the battery cases battery release button in the direction of the arrow (q), and then push the release button in the di-

rection of the arrow (w). The battery pack is then released. w q NEVER release or attach the battery case when the trans-

ceiver is wet or soiled. This may result water or dust getting into the transceiver or battery case and may result in the transceiver being damaged. 19 SPEAKER MICROPHONE 6 Optional HM-168LWP description Alligator type clip To attach the speaker-mic. to your shirt or collar, etc. Attaching Attach the connector of the speaker-microphone into the [SP MIC] jack on the transceiver and tighten the screws with your fingers. PTT switch Transmits while pushed Receives while released Microphone Speaker Turn the transceiver power OFF when connecting the HM-168LWP. NEVER immerse the connector in water. If the connector becomes wet, be sure to dry it BEFORE attaching it to the transceiver. NOTE: The microphone is located as shown in the dia-

gram above. To maximize the readability of your transmit-

ted signal (voice), hold the microphone approximately 5 to 10 cm (2 to 4 inches) from your mouth, and speak in a normal voice level. NOTE: Use only your fingers instead of tools to tighten the screws. CAUTION: Attach the con-

nector snugly. A loose connection will al-

low water intrusion into the connector. Hand tighten IMPORTANT: Keep the [SP MIC] jack cover attached to the transceiver when the speaker-microphone is not in use. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 20 7 OPTIONAL SWIVEL BELT CLIP MB-93 contents Qty. q Belt clip ...........................................................................1 w Base clip .........................................................................1 q w r Clip the belt clip to a part of your belt. And insert the trans-

ceiver into the belt clip until the base clip inserted fully into the groove. Attaching Release the battery pack if it is attached. (p. 1) q w Slide the base clip in the direction of the arrow until the base clip locks and makes a click sound. t Once the transceiver is locked in place, it swivels as illus-

trated below. e Attach the battery pack. (p. 1) 21 Once the transceiver is locked in place, it will swivel 360 degrees. OPTIONAL SWIVEL BELT CLIP 7 Detaching q Turn the transceiver upside down in the direction of the arrow and pull it out of the belt clip. Release the battery pack if it is attached. (p. 1) w e Pinch the clip (q), and slide the base clip in the direction of the arrow (w). q w CAUTION:

HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR DETACHING THE TRANSCEIVER FROM THE BELT CLIP. Otherwise the transceiver may not be attached to the holder or swivel properly if the transceiver is accidentally dropped and the base clip is scratched or damaged. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 22 8 OPTIONS D BATTERY PACK Battery pack Voltage BP-232WP 7.4 V Capacity Battery life*

2250 mAh (min.) 2300 mAh (typ.) 20 hrs.

* When the power save function is turned ON, and the operating peri-

ods are calculated under the following conditions;

TX : RX : standby = 5 : 5 : 90 BP-240/BP-261 battery case BP-240: Battery case for 6 AAA (LR03) alkaline batteries BP-261: Battery case for 6 AA (LR6) alkaline batteries BP-240 and BP-261 have IPX4 waterproof protection. When in use, the transceivers waterproof rating meets IPX4. Operating period depends on the alkaline cells used. CHARGERS D BC-119N desktop charger + AD-106 charger adapter

+ BC-145S ac adapter For rapid charging of battery packs. An AC adapter may supplied with the charger, depending on the versions. Charging time: Approximately 3 hours for the BP-232WP. BC-121N multi-charger + AD-106 charger adapter (6 pcs.)

+ BC-157S ac adapter For rapid charging of up to 6 battery packs (six AD-106s are required) simultaneously. An AC adapter should be pur-

chased separately. Charging time: Approximately 3 hours for the BP-232WP. 23 BC-160 desktop charger + BC-145S ac adapter For rapid charging of battery packs. An AC adapter may be supplied with the charger, depending on the versions. Charging time: Approximately 3 hours for the BP-232WP. BC-171 desktop charger + BC-147S ac adapter An AC adapter may supplied with the charger, depending on the versions. Charging time: Approximately 10 hours for the BC-232WP. BC-197 multi-charger For rapid simultaneously charging of up to six battery packs. An AC adapter may be supplied with the charger, depending on the version. Charging time: Approximately 3 hours for the BP-232WP. DC CABLES D CP-23L cigarette lighter cable Allows charging of the battery pack through a 12 V cigarette lighter socket. (For BC-160/BC-171/BC-119N) OPC-515L/OPC-656 dc power cables Allows charging of the battery pack using a 13.8 V power source instead of the AC adapter. OPC-515L: For BC-119N/BC-160/BC-171 OPC-656: For BC-121N/BC-197 BELT CLIPS D MB-93 swivel belt clip MB-94/94R belt clip Exclusive alligator-type belt clip. MB-96N/96F leather belt hanger OPTIONS 8 Some options may not be available in some countries. Ask your dealer for details. Approved Icom optional equipment is designed for optimal performance when used with an Icom transceiver. Icom is not responsible for the destruction or damage to an Icom transceiver in the event the Icom transceiver is used with equipment that is not manufactured or approved by Icom. OTHER OPTIONS D HM-158LA/HM-159LA/HM-168LWP speaker-microphone Combination speaker-microphone that provides convenient operation while hanging the transceiver on your belt. HM-153LA/HM-166LA earphone-microphone Ideal for hands-free operation: clip the HM-153LA/HM-

166LA (with integrated PTT switch) to your lapel or breast pocket. Allows you to operate in rainy conditions. FA-SC25V/FA-SC55V/FA-SC25U/

FA-SC57U/FA-SC72U/FA-SC62V/

FA-SC63V/FA-SC03U antennas FA-SC55V: 150174 MHz FA-SC25V: 136150 MHz FA-SC57U: 430470 MHz FA-SC25U: 400430 MHz FA-SC62V: 150160 MHz FA-SC72U: 470520 MHz FA-SC63V: 155165 MHz FA-SC03U: 380430 MHz FA-SC56VS/FA-SC57VS/FA-SC73US stubby antennas FA-SC56VS: 150162 MHz FA-SC57VS: 160174 MHz FA-SC73US: 450490 MHz FA-SC61VC/FA-SC61UC cut antennas FA-SC61VC: 136174 MHz FA-SC61UC: 380520 MHz MB-130 vehicle charger bracket Mounts the BC-160 desktop charger onto variety of plac-

es in a vehicle. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 24 9 SAFETY TRAINING INFORMATION Your Icom radio generates RF electromagnetic ener-

gy during transmit mode. This radio is designed for and classified as Occupational Use Only, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for W ARNING use by the General Population in an uncontrolled environment. This radio has been tested and complies with the FCC and IC RF exposure limits for Occupational Use Only. In addition, your Icom radio complies with the following Standards and Guidelines with re-

gard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans:

FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. American National Standards Institute (C95.3-1992), IEEE Rec-

ommended Practice for the Measurement of Potentially Hazard-

ous Electromagnetic Fields RF and Microwave. The following accessories are authorized for use with this prod-

uct. Use of accessories other than those specified may result in RF exposure levels exceeding the FCC and IC requirements for wireless RF exposure.; Belt Clip (MB-93, MB-94/R and MB-

96N/F), Rechargeable Li-ion Battery Pack (BP-232WP) and Speaker-microphone (HM-158LA/HM-159LA/HM-168LWP). To ensure that your expose to RF electromagnetic energy is within the FCC and IC allowable limits for occupational use, always adhere to the follow-

ing guidelines:

CAU TION 25 DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC and IC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifi-

cally authorized by the manufacturer for use with this radio. DO NOT transmit for more than 50% of total radio use time (50%

duty cycle). Transmitting more than 50% of the time can cause FCC and IC RF exposure compliance requirements to be exceed-

ed. The radio is transmitting when the TX indicator lights red. You can cause the radio to transmit by pressing the PTT switch. ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the Icom belt-clips listed on page 23 when attaching the radio to your belt, etc., to ensure FCC and IC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound quality, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to assure that this radio operates with the FCC and IC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electro-

magnetic radiation such as hospitals, aircraft, and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are ex-

posed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Votre radio Icom produit une nergie lectromagntique de radiofrquences (RF), en mode de transmission. Cette radio est conue pour un usage professionnel seulement et classe comme tel, ce qui signifie quelle doit tre utilise uniquement dans le cadre d'un travail par des personnes conscientes des dangers et des me-

sures visant minimiser ces dangers. Elle NEST PAS conue pour une utilisation grand public, dans un environnement non contrl. Cet appareil a t valu et jug conforme, aux limites dexposition aux RF de la FCC et dIC, pour une utilisation grand public. En outre, votre radio Icom satisfait les normes et directives qui suivent en matire de niveaux d'nergie et dnergie lectromagntique de RF et dvaluation de tels niveaux en ce qui concerne lexposition humaine:

Supplment C, dition 97-01, du Bulletin OET n 65 de la FCC, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. Norme de lAmerican National Standards Institute (ANSI): IEEE C95.1-1992 sur les niveaux de scurit compatibles avec lexposition humaine aux champs lectromagntiques de radiofrquences (3 kHz 300 GHz). Norme de lANSI: IEEE C95.3-1992 sur la mthode dvaluation re-

commande du champ magntique potentiellement dangereux des radiofrquences et des micro-ondes. Les accessoires illustrs la p. 23-24 sont approuvs pour une utilisa-

tion avec ce produit. Lutilisation daccessoires autres que ceux prciss peut entraner des niveaux dexposition aux RF suprieures aux limites tablies par la FCC et dIC en matire dexposition aux RF sans fil. Afin de vous assurer que votre exposition une nergie lectromagntique de RF se situe dans les limites permises par la FCC et dIC pour une utilisation grand public, veuillez en tout temps respecter les directives suivantes:

SAFETY TRAINING INFORMATION 9 NE PAS faire fonctionner la radio sans quune antenne approprie y soit fixe, car ceci risque dendommager la radio et causer une exposition suprieure aux limites tablies par la FCC et dIC. Lantenne approprie est celle qui est fournie avec cette radio par le fabricant ou une antenne spcialement autorise par le fabricant pour tre utilise avec cette radio. NE PAS mettre pendant plus de 50 % du temps total dutilisation de lappareil (50 % du facteur d'utilisation). La notion 50% du facteur dutilisation sapplique galement au mode VOX/PTT. mettre pen-

dant plus de 50 % du temps total dutilisation peut causer une exposi-

tion aux RF suprieure aux limites tablies par la FCC et dIC. Lorsque le voyant DEL rouge sallume, cette radio est en train dmettre. La radio mettra si vous appuyez sur le bouton du microphone. TOUJOURS tenir lantenne loigne dau moins 2,5 cm de votre corps au moment dmettre et utiliser uniquement lattache pour ceinture Icom illustre la p. 23, lorsque vous attachez la radio votre ceinture, ou autre chose, de faon vous assurer de ne pas provoquer une exposi-

tion aux RF suprieure aux limites fixes par la FCC et dIC. Pour offrir vos interlocuteurs la meilleure qualit de transmission possible, tenez lantenne au moins 5 cm de votre bouche et lgrement de ct. Les renseignements ci-dessus fournissent lutilisateur toute linformation ncessaire sur lexposition aux RF et sur ce quil faut faire pour assurer que cette radio fonctionne en respectant les limites dexposition aux RF tablies par la FCC et dIC. Interfrence lectromagntique et compatibilit En mode de transmission, votre radio Icom produit de lnergie de RF qui peut provoquer des interfrences avec dautres appareils ou systmes. Pour viter de telles interfrences, mettez la radio hors tension dans les secteurs o une signalisation lexige. NE PAS faire fonctionner lmetteur dans des secteurs sensibles au rayonnement lectromagntique tels que les hpi-

taux, les aronefs et les sites de dynamitage. Usage professionnel/contrl Ce radio metteur est utilis dans des cas o des personnes sont exposes en raison de leur travail, pourvu quelles soient conscientes du risque dex-

position et quelles puissent exercer un contrle sur cette exposition. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 26 A-7082D-1EX-0a Printed in Japan 2013 Icom Inc. Printed on recycled paper with soy ink. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan