FCC ID: AFJ325100 VHF Amateur Transceiver

 

INSTRUCTION MANUAL VHF TRANSCEIVER This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FOREWORD Thank you for purchasing this Icom radio. The IC-2300H VHF TRANSCEIVER is designed and built with Icoms state of the art technology and craftsmanship. With proper care this radio should provide you with years of trouble-free operation. D FEATURES 65 W* high transmit output power

(*except Korea/Taiwan versions) Tone squelch, DTCS squelch standard Three color (amber, yellow & green) back-

light LCD screen Remote control microphone available IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL This instruction manual contains important operating instructions for the IC-2300H. EXPLICIT DEFINITIONS WORD DEFINITION R WARNING! Personal injury, re hazard or electric CAUTION NOTE shock may occur. Equipment damage may occur. Recommended, only inconvenience. No risk of personal injury, re or elec-

tric shock. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United King-

dom, Germany, France, Spain, Russia and/or other countries. SUPPLIED ACCESSORIES q Microphone (HM-133V) . 1 w Fuse (20 A) . 1 e DC power cable (3 m) . 1 r Mobile mounting bracket . 1 t Mounting screws, nuts and washers . 1 set y Microphone hanger . 1 Not supplied, depending on the version. q w e r t y OPTIONS HM-133V REMOTE-CONTROL MICROPHONE HM-154 HAND MICROPHONE SP-10 EXTERNAL SPEAKER OPC-440A MIC EXTENSION CABLE OPC-589 ADAPTER CABLE OPC-1132A/OPC-347 DC POWER CABLES CS-2300H CLONING SOFTWARE OPC-478/OPC-478UC CLONING CABLES OPC-474 CLONING CABLE FCC INFORMATION FOR CLASS B UNINTENTIONAL RADIATORS:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-

stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television recep-

tion, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dif-

ferent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. i Approved Icom optional equipment is designed for optimal per-

formance when used with an Icom transceiver. Icom is not responsible for the destruction or damage to an Icom transceiver in the event the Icom transceiver is used with equip-

ment that is not manufactured or approved by Icom. For only U.S.A. CAUTION: Changes or modi cations to this device, not express-

ly approved by Icom Inc., could void your authority to operate this device under FCC regulations. PRECAUTIONS RWARNING RF EXPOSURE! This device emits RadioFrequency (RF) energy. Extreme caution should be ob-

served when operating this device. If you have any questions regarding RF exposure and safety standards, please refer to the Federal Communications Commission Of ce of Engineering and Technologys report on Evaluating Compliance with FCC Guide-

lines for Human Radio frequency Electromagnetic Fields (OET Bulletin 65). RWARNING! NEVER connect the transceiver to an AC outlet. This may pose a re hazard or result in an electric shock. RWARNING! NEVER cut the DC power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting, the transceiver may be damaged. RWARNING! NEVER operate the transceiver while driving a vehicle. Safe driving requires your full attentionany-

thing less may result in an accident. RWARNING! NEVER connect the transceiver to a power source of more than 16 V DC or use reverse polarity. This could cause a re or damage the transceiver. CAUTION: NEVER expose the transceiver to rain, snow or any liquids. The transceiver may be damaged. RWARNING! NEVER operate or touch the transceiver with wet hands. This may result in an electric shock or damage the transceiver. RWARNING! NEVER place the transceiver where nor-

mal operation of the vehicle may be hindered or where it could cause bodily injury. RWARNING! NEVER let metal, wire or other objects touch any internal part of the transceiver. This may result in an electric shock. DO NOT push the PTT when not actually intending to trans-

mit. KEEP the transceiver out of the reach of children. During mobile operation, DO NOT operate the transceiver without running the vehicles engine. When the transceivers pow-

er is ON and your vehicles engine is OFF, the vehicles battery will soon become exhausted. BE CAREFUL! The transceiver will become hot when op-

erating it continuously for long periods of time. DO NOT set the transceiver in a place without adequate ventilation. Heat dissipation may be affected, and the transceiver may be damaged. DO NOT use or place the transceiver in direct sunlight or in areas with temperatures below 10C (+14F) or above +60C

(+140F). DO NOT use harsh solvents such as benzine or alcohol when cleaning, as they will damage the transceivers surfaces. USE only Icom microphones (supplied or optional). Other man-

ufacturers microphones have different pin assignments and may damage the transceiver if attached. ii TABLE OF CONTENTS FOREWORD ......................................................................................... i IMPORTANT .......................................................................................... i EXPLICIT DEFINITIONS ....................................................................... i SUPPLIED ACCESSORIES .................................................................. i OPTIONS .............................................................................................. i FCC INFORMATION ............................................................................. i PRECAUTION ...................................................................................... ii TABLE OF CONTENTS ....................................................................... iii QUICK REFERENCE GUIDE ...................................................... IVVII Installation ................................................................................... iv Your rst contact .......................................................................... vi Repeater operation ..................................................................... vi Programming memory channels ................................................ vii 1 PANEL DESCRIPTION ............................................................... 14 Front panel ................................................................................... 1 Function display ........................................................................... 2 Rear panel ................................................................................... 3 Microphone (HM-133V) ................................................................ 3 Microphone keypad ...................................................................... 4 2 SETTING A FREQUENCY .......................................................... 57 Preparation .................................................................................. 5 Using the tuning dial .................................................................... 5 Using the keypad ......................................................................... 5 Using the [Y] or [Z] keys ............................................................. 5 Tuning step selection .................................................................... 6 Lock functions .............................................................................. 7 3 BASIC OPERATION .................................................................. 814 Receiving ..................................................................................... 8 Monitor function ........................................................................... 8 Audio mute function ..................................................................... 9 Squelch attenuator ....................................................................... 9 S-meter squelch ........................................................................... 9 Transmitting ................................................................................ 10 Selecting output power ............................................................... 11 One-touch PTT function ............................................................. 11 Accessing a repeater ................................................................. 12 Subaudible tones ....................................................................... 13 4 REPEATER SETTING ............................................................. 1516 Frequency offset ......................................................................... 15 Repeater lockout ........................................................................ 15 Reversed duplex function ........................................................... 16 Auto repeater ............................................................................. 16 5 MEMORY OPERATION ........................................................... 1726 General description .................................................................... 17 Programming a memory channel ............................................... 17 Memory channel selection ......................................................... 18 Copying memory contents ......................................................... 19 Programming channel names ..................................................... 21 Memory clearing ........................................................................ 22 Memory bank setting .................................................................. 23 Memory bank selection .............................................................. 24 Transferring bank links ............................................................... 25 Erasing bank links ...................................................................... 26 6 CALL CHANNEL OPERATION ............................................... 2728 Call channel selection ................................................................ 27 Copying Call channel contents ................................................... 27 Programming a Call channel ...................................................... 28 7 SCAN OPERATION ................................................................. 2933 Scan types ................................................................................. 29 Scan start/stop ........................................................................... 30 Scan edges programming .......................................................... 31 Skip channel setting ................................................................... 32 Scan Resume function ............................................................... 33 8 PRIORITY WATCH .................................................................. 3435 Priority watch types .................................................................... 34 Priority watch operation ............................................................. 35 9 DTMF MEMORY ENCODER ................................................... 3638 Programming a DTMF code ....................................................... 36 Transmitting a DTMF code ......................................................... 37 DTMF TX speed ......................................................................... 38 10 POCKET BEEP AND TONE SQUELCH ................................. 3942 Pocket beep operation ............................................................... 39 Tone/DTCS squelch operation ................................................... 41 Tone scan ................................................................................... 42 11 OTHER FUNCTIONS .............................................................. 4353 Set mode .................................................................................... 43 Initial Set mode .......................................................................... 47 Weather channel operation ........................................................ 50 Microphone keys ........................................................................ 51 Partial reset ................................................................................ 52 All reset ...................................................................................... 52 Data cloning ............................................................................... 53 12 SPECIFICATIONS ......................................................................... 54 13 MAINTENANCE ............................................................................ 55 Troubleshooting .......................................................................... 55 Fuse replacement ...................................................................... 55 1 2 3 4 5 6 7 8 9 10 11 12 13 iii QUICK REFERENCE GUIDE Installation D Location Select a location which can support the weight of the transceiver and does not interfere with driving in any way. We recommend the locations shown in the dia-

gram below. RWARNING! NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury. RWARNING! NEVER place the transceiver where air bag deployment may be obstructed. DO NOT place the transceiver where hot or cold air blows directly onto it. DO NOT place the transceiver in direct sunlight. D Battery connection RWARNING! NEVER connect the transceiver di-

rectly to a 24 V battery. DO NOT use the cigarette lighter socket for a power connection. When passing the DC power cable through metal mate-

rial, use a rubber grommet to prevent short circuiting. CONNECTING TO A DC POWER SUPPLY

(See page 55 for fuse replacement.) Grommet IC-2300H red+

black Fuses 20 A _ black

+ red 12 V 12 V battery NOTE:

Use terminals for the cable connections. Crimp Supplied DC power cable Solder D DC power supply connection Use a 13.8 V DC power supply with a capacity of at least 20 Amps. Make sure the ground terminal of the DC power supply is connected to a secure earth. CONNECTING TO A DC POWER SOURCE D Using the mounting bracket Drill 4 holes where the mounting bracket is to be in-

stalled. Approx. 5.56 mm (0.25 inch) when using nuts; ap-

proximately 23 mm (0.13 inch) when using self-

tapping screws. Insert the supplied screws, nuts and washers through the mounting bracket and tighten. Adjust the angle for the clearest view of the function display. Nut Spring washer Flat washer When using self-tapping screws Insulating sheet Spring washer Mounting bracket Mounting bolt IC-2300H DC power supply 13.8 V

to an AC outlet IMPORTANT!

Detailed installation notes for Icom mobile transceiv-

ers are available. Contact your Icom dealer or dis-

tributor. Fuses 20 A

black red

(See page 55 for fuse replacement.) iv D Antenna installation Antenna location To obtain maximum performance from the transceiv-

er, select a high-quality antenna and mount it in a good location. When you use a magnetic mount, use a non-radial antenna. Roof-mount antenna

(Drill a hole or use a magnetic mount.) Trunk-mount antenna Gutter-mount antenna to the antenna Installing the antenna connector PL-259 CONNECTOR The antenna uses a PL-259 connector. 30 mm Coupling ring 10 mm (Tin) 10 mm (Tin) 12 mm solder solder q Slide the coupling ring down. Strip the cable jacket and tin the ground shield. w Strip the cable as shown at left. Tin the center conduc-

tor. e Slide the connector body on and solder it. r Screw the coupling ring onto the connector body.

(10 mm=0.4 inch) NOTE: There are many publications covering proper antennas and their installation. Check with your local dealer for more information and recommendations. QUICK REFERENCE GUIDE D Connecting the microphone Connect the microphone to the eight-pin modular sock-

et on the front panel of the transceiver.

*HM-133V; A different microphone may be supplied with some versions. v QUICK REFERENCE GUIDE Your rst contact Now that you have your IC-2300H installed in your car or shack, you are probably excited to get on the air. We would like to take you through a few basic operation steps. 1. Turning ON the transceiver Before turning ON your IC-2300H, make sure the au-

dio volume and squelch level controls are set to 910 oclock. Repeater operation 1. Setting duplex Hold down [DUP] (LOW) for 1 second one or more times to select minus duplex or plus duplex. The USA version has an Auto Repeater function, therefore, setting duplex is not required. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz

[VOL]

[SQL]

Set both [VOL] and [SQL] to the 910 oclock position. Although you have purchased a brand new transceiver, some settings may have changed from the factory de-

faults because of the QC process. The Partial Rest is recommended to start with factory default settings.

[SCAN] (V/MHz) While holding down [V/MHz], hold down [

] for 1 sec-

ond to reset the CPU. 2. Tune the desired frequency

[DIAL] will allow you to set the frequency you want to op-

erate on. Page 6 explains how to set the tuning speed. 2. Repeater tone If accessing the repeater, requires a subaudible tone, push [TONE] one or more times until appears. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Using the HM-133V Plus or minus duplex selection and the repeater tone setting can easily be made using the HM-133V. Push [DUP] for minus duplex; [DUP+]

duplex selection, then push [FUNC]

[DUP] to turn ON the repeater tone. for plus

, and then Push Push MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz

[DIAL]

Push , then Using the HM-133V You can directly enter the frequency with the HM-133V keypad.

[i.e.]: Setting the frequency to 145.3625 MHz. Push Push Push Push MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz vi Programming memory channels The IC-2300H has a total of 207 memory channels for storing often used operating frequencies, repeater set-

tings, and so on. Memories include 6 scan edges and 1 Call channel. 1. Setting the frequency In the VFO mode, set the desired operating frequency, repeater, tone and tuning steps, and so on. 2. Selecting the memory channel Push [S.MW], and then rotate [DIAL] to select the de-

sired memory channel. The icon and memory channel number blink. 3. Writing a memory channel Hold down [MW] (S.MW) for 1 second to program. 3 beeps sound The memory channel number automatically increases when continuing to hold down [MW] (S.MW) after pro-

gramming. Using the HM-133V q In the VFO mode, set the desired operating frequen-

cy, offset and direction, tone settings, and so on. w Push [FUNC]

e Push [Y] or [Z] to select the desired memory chan-

icon and memory channel number blink. then [MW]

The

. nel. r Push [FUNC]

then hold down [MW]

for 1 sec-

ond to save the setting. 3 beeps sound The memory channel number automatically increas-

es when you continuing to hold down [MW]

after programming. QUICK REFERENCE GUIDE MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz

[S.MW] (MW)

[DIAL]

Push , then MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Vii 1 PANEL DESCRIPTION Function display (p. 2)

!3 Front panel q w e MW S.MW VOL SQL r t y u i o

!0

!1

!2 BANK OPT

q POWER KEY [

Hold down for 1 second to turn power ON or OFF. w MEMORY WRITE KEY [S.MW MW] (p. 17) Push to enter the memory write mode. Hold down for 1 second to program a selected memory channel. Continue to hold down the key to automatically increment the memory channels. e MICROPHONE CONNECTOR Connect the supplied microphone here. r VOLUME CONTROL [VOL] (p. 8) Rotate to adjust the audio level. t SQUELCH CONTROL [SQL] (p. 8) Rotate to adjust the squelch level. The S-meter squelch or attenuator squelch is ac-

tivated, when you rotate [SQL] clockwise from the center position. (p. 9) Noise squelch Squelch threshold Squelch is open. Squelch attenuator or S-meter squelch Shallow Deep y SETLOCK KEY [SET LOCK]

Push to enter to the Set mode. (p. 43) Hold down for 1 second to turn the Lock function ON or OFF. (p. 7) u MONITORCHANNEL NAME KEY [MONI ANM]

Push to turn the monitor function ON or OFF. (p. 8) Push to turn the channel names or number ON or OFF, in the memory and Call channel modes.

(p. 21) 1 i OUTPUT POWERDUPLEX KEY [LOW DUP]

Push to toggle the output power. (p. 11) Hold down for 1 second to select the minus du-

plex, plus duplex or simplex operation. (p. 12) o TONETONE SCAN KEY [TONE T-SCAN]

Push to select the tone function. (pp. 39, 41) Hold down for 1 second to start the Tone Scan.

(p. 42)

!0 MEMORY/CALLPRIORITY KEY [M/CALL PRIO]

Push to select and toggle memory, Call and weather channel* modes. (pp. 18, 27, 50)

*For only USA versions. Hold down for 1 second to start the priority watch.

(p. 34)

!1 VFO/MHz TUNINGSCAN KEY [V/MH z SCAN]

Push to select the VFO mode. (p. 5) In the VFO mode, push to select the tuning step.

(p. 5) Push to cancel the scan while scanning. Hold down for 1 second to start a scan. (p. 29)

!2 BANKOPTION KEY [BANK OPT]

Push to select the memory bank while in the memory mode. (p. 23) Hold down for 1 second to enter the Option Set mode. (p. 36)

!3 TUNING DIAL [DIAL]

Sets the operating frequency (p. 5), memory channel. (p. 18) Sets the item in the Set mode. (p. 43) Changes the scanning direction. (p. 30) D Microphone connector (front panel view) q i q +8 V DC output (Max. 35 mA) w Channel up/down e 8 V control IN r PTT t GND (microphone ground) y MIC (microphone input) u GND i Data IN PANEL DESCRIPTION 1 Function display

!8

!7

!6

!5

!4

!3

!2

!1 q w e r t y q FREQUENCY READOUT Shows the operating frequency, channel name, Set mode contents, and so on. The frequency decimal point blinks during a scan.

(p. 30) While the DTMF memory function is in use, d ap-

pears in the 100 MHz digit. (p. 36) w TRANSMIT ICON Appears while transmitting. (p. 10) Blinks while transmitting with the One-Touch PTT function. (p. 11) e AUDIO MUTE ICON (p. 9) Appears when the Audio Mute function is activated. r NARROW MODE ICON (p. 43) Appears when the narrow FM mode is selected. t OUTPUT POWER ICONS (p. 11) Displays the selected transmit output power level. The Mid-Low power is not selectable in the Taiwan version. y KEY ICONS Displays the function(s) of the front panel keys di-

rectly below the function display. u SKIP ICON (p. 32) Appears when the selected memory channel is set as a skip channel. i MEMORY CHANNEL NUMBER READOUT Displays the selected memory channel number.

(p. 18) C appears when the Call channel is selected.

(p. 27) o MEMORY ICON (p. 17) Appears when the Memory mode is selected.

!0 S/RF INDICATOR Shows the relative signal strength, while receiving signals. (p. 8) Shows the output power level, while transmitting.

(p. 10)

!0 o i u

!1 BUSY ICON (p. 8) Appears when receiving a signal, or the squelch is open. Blinks while the monitor function is turned ON.

!2 S-METER SQUELCH ICON (p. 9) Appears while the S-meter Squelch function is turned ON.

!3 SQUELCH ATTENUATOR ICON (p. 9) Appears while the Squelch Attenuator function is turned ON.

!4 PRIORITY WATCH ICON (p. 35) Appears during Priority Watch.

!5 AUTO POWER OFF ICON (p. 47) Appears when the Auto Power OFF function is turned ON.

!6 TONE ICONS The and icons appear while the subaudible tone encoder is in use. (p. 13) The and icons appear while the DTCS en-

coder is in use. (p. 13) The icon appears while the Tone Squelch

(CTCSS) function is in use. (p. 41) The and icons appear while the Reverse Tone Squelch (CTCSS) function is in use. (p. 41) The icon appears while the Tone Squelch

(DTCS) function is in use. (p. 41) The and icons appear while the Reverse Tone Squelch (DTCS) function is in use. (p. 41) The icon appears with the icon, while the pocket beep function (CTCSS or DTCS) is in use.

(p. 39) or

!7 DUPLEX ICONS (p. 12) The + icon appears in the plus duplex mode, and the icon appears in the minus duplex mode.

!8 LOCK ICON (p. 7) Appears while the Lock function is turned ON. 00 1 2 3 4 5 6 7 8 9 10 11 12 13 2 1 PANEL DESCRIPTION Rear panel q e w q ANTENNA CONNECTOR [ANT]

Connect a 50 : antenna with a PL-259 connector, through a 50 : coaxial cable. e SPEAKER JACK [SP]

Connect a 4 : speaker here. Audio output power is more than 3.5 W. w POWER RECEPTACLE [DC13.8V]

Connect a 13.8 V DC 15% power source with the supplied DC power cable. NOTE: DO NOT use a cigarette lighter socket as a power source, when operating in a vehicle. The plug may cause voltage drops and ignition noise may be superimposed onto the transmit or receive audio. Microphone (HM-133V) q w e r t

!1

!0 o i u y Mic element q VFO/LOCK KEY [VFO/LOCK]

Push to select the VFO mode. (p. 5) Hold down for 1 second to turn the Lock function ON or OFF. (p. 7) w PTT SWITCH Hold down to transmit; release to receive. Toggles between transmitting and receiving while the One-Touch PTT function is in use. (p. 11) e UP/DOWN KEYS [Y] or [Z]

Push either key to change the operating frequen-

cy, memory channel, mode setting, and so on.

(pp. 5, 18, 43) Hold down either key for 1 second to start scan-

3 ning. (p. 30) r ACTIVITY INDICATOR Lights red while any key, except [FUNC]

and

[DTMF-S]

, is pushed, or while transmitting. Lights orange while the Microphone Keypad Lock function is activated. Lights green while the One-Touch PTT function is in use. t KEYPAD (p. 4) Push to activate various functions. y FUNCTION INDICATOR Lights orange while [FUNC]

is activated indicating the secondary function of keys can be accessed. Lights green when [DTMF-S]

is activated DTMF signals can be transmitted using the key-

pad. u FUNCTION KEY [FUNC] (p. 4) i DTMF MEMORY SELECT KEY [DTMF-S] (p. 37) o FUNCTION KEYS [F-1] or [F-2] (p. 51) Program and re-call your desired transceiver set-

ting.

!0 BANK/OPTION KEY [BANK/OPTION]

Push to select the memory bank option, when in the memory mode. (p. 24) Hold down for 1 second to enter the Option Set mode.

!1 MEMORY/CALL KEY [MR/CALL]

Push to select the memory mode. (p. 18) Hold down for 1 second to select the Call channel.

(p. 27) PANEL DESCRIPTION 1 Microphone keypad KEY FUNCTION SECONDARY FUNCTION (

+key) OTHER FUNCTION Opens and closes the squelch. (p. 8) Starts and stops scanning. (p. 30) Turns the channel names or number display ON or OFF, in the memory mode. (p. 21) Starts and stops tone scanning. (p. 42) Starts and stops priority watch. (p. 35) Selects high output power. (p. 11) Turns the One-Touch PTT function ON or OFF.

(p. 11) Turns the DTCS squelch ON. (p. 41) After pushing [DTMF-S]

, transmits the appropriate DTMF code. (pp. 14, 37) When the DTMF memory encoder is activated, push [0] to [9] to transmit the appropriate DTMF memory contents.

(p. 37) Selects mid output power. (p. 11) Turns ON the DTCS pocket beep function. (p. 39) Selects low output power. (p. 11) Selects the minus duplex mode. (p. 12) Selects the plus duplex mode. (p. 12) Selects the simplex mode. (p. 12) Adjusts the audio level. (p. 8) Cancels frequency entry. (p. 5) Cancels the scan or priority watch.

(pp. 30, 35) Exit the Set mode. (p. 43) Enters the Set mode. (p. 43) Selects the next item in the Set mode.

(p. 43) Sets the keypad for numeral input.

(p. 5) Selects the previous item in the Set

(p. 43) mode. Adjusts the squelch level. (p. 8) Adjusts the audio level. (p. 8) Adjusts the squelch level. (p. 8) Turns ON the DTMF memory encoder function.

(p. 37) Turns ON the subaudible tone encoder. (p. 13) Turns ON the CTCSS pocket beep function.

(p. 39) Turns the Tone Squelch function ON. (p. 41) Sends a 1750 Hz tone signal while held down.

(p. 14) Selects a memory channel programming mode.

(p. 17) Advances the memory channel number when continuously held down after programming is completed. (p. 17) Turn OFF the DTMF memory mode. (p. 37) Turns OFF the subaudible tone encoder, pocket beep or CTCSS/DTCS tone squelch. (pp. 13, 39, 41) Mutes the audio. (p. 9) The Mute function is released when any opera-

tion is performed. Sends a 1750 Hz tone signal for 1 second. (p. 14) Locks the digit keys on the keypad (including the

[A] to [D], [#] and [M] keys. (p. 7) Lights orange while the Microphone Keypad Lock function is activated. 00 1 2 3 4 5 6 7 8 9 10 11 12 13 4 2 SETTING A FREQUENCY Preparation D Turning power ON/OFF Hold down [

] for 1 second to turn the power ON or OFF. D VFO mode selection The IC-2300H has 2 basic operating modes; VFO mode and memory mode. Push [V/MH z] to select the VFO mode. Push [M/CALL] to select the memory mode. Using the HM-133V Push [VFO]

to select the VFO mode. Hold down [ ] for 1 second. Push [V/MHz]

to select the VFO mode. Push [M/CALL]

to select the memory mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz VFO mode MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Memory mode Using the dial Rotate [DIAL] to set the frequency. If necessary, push [V/MH z] to select the VFO mode. The frequency changes according to the selected tuning step. (p. 6) Push [V/MH z] one or more times, to toggle the frequency step between 1 MHz and 10 MHz, if de-

sired. If the scan starts:

Holding down [SCAN] (V/MHz) for 1 second will start a scan. Push [V/MH z] again to cancel it. Rotate [DIAL] to set the frequency. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz In the VFO mode Push [V/MHz] to toggle the tuning step. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz The 1 MHz tuning step is selected Using the keypad on the HM-133V z If necessary, push [VFO]

to select the VFO

[EXAMPLE]: Setting the frequency to 145.3625 MHz. mode. x Push [ENT]

to activate the keypad for numerical input. c Push 6 keys to input the frequency. When a digit is mistakenly input, push [ENT]

to clear the input, and then re-enter from the 1st digit. Push [CLR]

to clear the input digits and recall the previous frequency. Using

[Y] or [Z] on the HM-133V Push [Y] or [Z] to select the desired frequency. Holding down [Y] or [Z] for 1 second activates a scan. If a scan has started, push [Y] or [Z] again or push [CLR]

to cancel it. 5 Push Push Push Push MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz SETTING A FREQUENCY 2 Tuning step selection The tuning step is the smallest selectable frequency increment you can set the operating frequency. The fol-

lowing tuning steps are selectable. 5 kHz 6.25 kHz 10 kHz 12.5 kHz 15 kHz 20 kHz 25 kHz 30 kHz 50 kHz NOTE: For convenience, select the tuning step that matches the frequency intervals of the repeaters in your area. q If necessary, push [V/MH z] to select the VFO mode. w Push [SET] to enter the Set mode. e Push [SET] or [MONI] one or more times, until TS appears, as shown to the right. r Rotate [DIAL] to select the desired tuning step. t Push any key, other than [SET] or [MONI], to save the entry and exit the Set mode. Using the HM-133V z If necessary, push [VFO]

to select the VFO mode. x Push [SET]

c Push [SET]

TS appears. to enter the Set mode. or [ENT]

one or more times until v Push [Y] or [Z] to select the desired tuning step. b Push [MW]

to save the entry and exit the Set mode. 15 kHz tuning step MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz 00 1 2 3 4 5 6 7 8 9 10 11 12 13 6 2 SETTING A FREQUENCY Lock functions Use the Lock function to prevent accidental channel changes and unnecessary function access. The IC-

2300H has two different lock functions. D Lock function This function electronically locks [DIAL] and the key-

pad. This function can be used together with the Micro-

phone Lock function. Hold down [LOCK] (SET) for 1 second to turn the Lock function ON or OFF.

[PTT], [MONI], [VOL] and [SQL] can be used, even while the Frequency Lock function is ON. TONE-1, TONE-2, DTMF tones or DTMF memory contents can also be transmitted from the micro-

phone. Hold down [LOCK] (SET) for 1 second. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Appears Using the HM-133V Hold down [LOCK]

function ON or OFF. for 1 second to turn the Lock Hold down for 1 second. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Appears Push , then . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz D Microphone Keypad Lock This function electronically locks the microphone key-

pad. Push [FUNC]

then [16KEY-L]

to turn the Microphone Keypad Lock function ON or OFF. The activity indicator lights orange, while the Micro-

phone Keypad Lock function is activated.

[PTT], [VFO/LOCK]

[BANK/OPTION]

[DTMF-S]

can be used. All keys on the transceiver can be used. When the transceiver's power is turned OFF, the

, on the microphone

, [MR/CALL]

, [F-2]

, [Y], [Z], [F-1]

and [FUNC]

Keypad Lock function is also turned ON. 7 3 BASIC OPERATION Receiving q Hold down [

w Rotate [VOL] to adjust the audio level. Push [MONI] to open the squelch, and then rotate

] for 1 second to turn ON the power.

[VOL] to adjust the audio level. e Set the squelch level. First, rotate [SQL] fully counterclockwise, and then rotate [SQL] clockwise until the noise just disappears. r Set the operating frequency. (p. 5) t When you receive a signal, the squelch opens and audio can be heard. The BUSY icon appears, and the S/RF indicator shows the relative strength of the received signal. Using the HM-133V The audio level can also be adjusted by pushing

[VOLY]

or [VOLZ]

. The squelch level can also be adjusted by pushing

[SQLY]

or [SQLZ]

. Monitor function This function is used to listen to weak signals without disturbing the squelch setting, or to manually open the squelch, even when the tone squelch is in use. Push [MONI] to open the squelch. The BUSY icon blinks. Push [MONI] again to cancel the function. Using the HM-133V Push [MONI]

Push [MONI]

to open the squelch. again to cancel the function. NOTE: When the squelch adjustment is set to too far clockwise (12 17 oclock position), the S-meter squelch or squelch attenuator is activated. To moni-

tor weak signals, deactivate the S-meter squelch or squelch attenuator function. See page 9 for details. 8 Appears when receiving a signal. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push / to adjust the audio level. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Audio level Push / to adjust the squelch level. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Squelch level Push [MONI] to open the squelch. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to open the squelch. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz BASIC OPERATION 3 Audio mute function This function temporarily mutes the audio without dis-

turbing the volume setting. then [SQLY D(MUTE)]

Push [FUNC]

mute the audio. The MUTE icon appears. Push [CLR]

to cancel the function. to Push then . Appears MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Mute Squelch attenuator The transceiver has an RF attenuator related to the squelch level setting. Approximately 20 dB of attenua-

tion is obtained at the maximum setting.

] to turn OFF the power. Turn ON the Squelch Attenuator function:

q Push [

w While holding down [LOCK] (SET), hold down [

] for 1 second to turn ON the power and enter the Initial Set mode. MUTE NAR MID LOW LOCK SET NAR MID LOW LOCK SET DIGITAL PRIO AO ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz ATT AO Appears ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz While the squelch attenuator is turned ON.

([DIAL] is set between the 12 oclock and fully clockwise positions.) e Push [SET] or [MONI] one or more times, to select the SQL item. r Rotate [DIAL] to select AT (Attenuator). t Push [

y Rotate [SQL] clockwise further than the 12 oclock

] to exit the Initial Set mode. position, to activate the squelch attenuator. The attenuation level can be adjusted up to 20 dB

(approximately), between the 12 oclock and fully clockwise positions. When setting the squelch from the microphone, the level greater than 18 activates the squelch attenuator. NOTE: When using with the Monitor function. The squelch attenuator functions even when the Monitor function is in use. It is recommended to set

[SQL] between 10 and 12 oclock (7 to 17 level when it is set using the HM-133V). S-meter squelch The transceiver has an S-meter squelch. The S-meter squelch allows you to set minimum signal level needed to open the squelch. 00 1 2 3 4 5 6 7 8 9 10 11 12 13

] to turn OFF the power. Turn ON the S-meter Squelch function:

q Push [

w While holding down [LOCK] (SET), hold down [

] for 1 second to turn ON the power and enter the Initial Set mode. e Push [SET] or [MONI] one or more times, to select the SQL item. r Rotate [DIAL] to select SS (S-meter squelch). t Push [

y Rotate [SQL] clockwise further than the 12 oclock

] to exit the Initial Set mode. position, to activate the S-meter squelch. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz S-meter squelch S SQL Appears NAR MID LOW LOCK SET ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz While the S-meter squelch is turned ON.

([DIAL] is set between the 12 oclock and fully clockwise positions.) 9 Appears Output power level Selected output power MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz 3 BASIC OPERATION Transmitting CAUTION: Transmitting without an antenna will dam-

age the transceiver. NOTE: To prevent interference, listen on the channel before transmitting by opening the squelch. To open the squelch, rotate [DIAL] counterclockwise or push

[SQLZ]

on the microphone. q Set the operating frequency. (p. 5) Adjust the output power if desired. See below for the details. w Hold down [PTT] to transmit. The $ icon appears. The S/RF indicator shows the output power level. The One-Touch PTT function can be used. See page 11 for details. e Speak into the microphone at your normal voice level. DO NOT hold the microphone too close to your mouth, or speak too loudly. This may distort the signal. r Release [PTT] to receive. IMPORTANT! (for 65 W transmission):

The IC-2300H has a built-in current detector circuit which protects the power ampli er from excessive cur-

rent ow. When excessive current ow is detected, the circuit automatically reduces the transmit output power to approximately 25 watts. The IC-2300H has a thermal detector circuit too, which protects the power ampli er from excessive heat. As the temperature increases, the circuit automatically re-

duces the transmit output power to approximately 10 to 20 watts. 10 BASIC OPERATION 3 Selecting output power The IC-2300H has 4* output power levels to suit your operating requirements. Lower output powers during short-distance communications may reduce the pos-

sibility of interference to other stations and will reduce current consumption.

*The Taiwan version has only 3 output power level options. Push [LOW] one or more times to select the output power. The output power can be changed even while transmitting. OUTPUT POWER (approximately) High:

Mid:

Mid-Low:

Low:

USA, Export Taiwan Korea 65 W 25 W 10 W 5 W 24 W 50 W 10 W 5 W 25 W 10 W 5 W MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz The selected output power is displayed here.

(If High is selected, no icon is displayed.) Using the HM-133V Push [HIGH]

for high output power; [MID]

for mid-low output power (push again for mid output power); and [LOW]

When using the microphone, output power can be for low output power. changed only while receiving. One-touch PTT function The PTT switch can be operated as a one-touch PTT switch (each push switches between transmit and re-

ceive). Using this function you can transmit without holding down the PTT switch. To prevent accidental continuous transmissions with this function, the transceiver has a time-out timer. See page 48 for details. z Push [FUNC]

then [PTT-M]

to turn ON the One-Touch PTT function. The activity indicator lights green. x Push [PTT] to transmit and push again to receive. Two beeps sound when transmit starts, and a long beep sounds when returning to receive. The $ icon blinks while the One-Touch PTT function is ON. c Push [FUNC]

then [PTT-M]

to turn OFF the One-Touch PTT function. The activity indicator goes out. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz 00 1 2 3 4 5 6 7 8 9 10 11 12 13 11 3 BASIC OPERATION Accessing a repeater q Set the receive frequency (repeater output frequen-

cy). (p. 5) w Set the frequency offset in the Set mode. (p. 15) e Hold down [DUP] (LOW) for 1 second, once or twice, to select the minus duplex or the plus duplex mode. The or + icon appears to represent the fre-

quency offset direction. For only USA versions:

When the Auto Repeater function is ON (p. 16), steps w and e are not necessary. r Push [TONE] one or more times to turn ON the sub-

audible tone encoder, depending on the repeater requirements. The The 88.5 Hz tone frequency is set as the default. But some repeaters may require a different tone frequency to access. Refer to page 13 for setting the tone frequency. icon appears t Hold down [PTT] to transmit. The displayed frequency automatically changes to the transmit frequency (repeater input frequency). If OFF appears, con rm that the frequency offset is correctly set. (p. 15) y Release [PTT] to receive. u Push [MONI] to check whether you can directly re-

ceive the signal from the other station. i To return to the simplex mode, hold down [DUP]

(LOW) for 1 second, once or twice, to clear the or

+ icon. o To turn OFF the subaudible tone encoder, push

[TONE] one or more times until no tone icon ap-

pears. Using the HM-133V z Set the receive frequency (repeater output frequen-

cy). (p. 5) or push [DUP+]

v Push [FUNC]

x Set the frequency offset in the Set mode. (p. 15) c Push [DUP]

to select the minus duplex mode, to select the plus duplex mode. to turn ON the subaudible tone encoder, depending on the repeat-

er requirements. Refer to page 13 for setting the tone frequency. When the repeater requires a different tone sys-

then [TONE]

tem, see page 14. b Hold down [PTT] to transmit. n Release [PTT] to receive. m Push [MONI]

to check whether you can directly receive the signal from the other station.

, Push [SIMP]

. To turn OFF the subaudible tone encoder, push The + or icon disappears. to return to the simplex mode.

[FUNC]

then [T-OFF]

. 12

[i.e.]: Select the minus duplex mode, and then turn ON the subaudible tone encoder. Appears. DIGITAL PRIO AO BUSY Push [DUP] (LOW) to select the duplex mode. ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Appears DIGITAL PRIO AO BUSY Push [TONE] to turn ON the subaudible tone encoder. ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET While transmitting

(The displayed frequency changes to the transmit frequency) MUTE NAR MID LOW LOCK SET DIGITAL PRIOAO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz While receiving

[i.e.]: Select the plus duplex mode, and then turn ON the subaudible tone encoder. Appears MUTE NAR MID LOW LOCK SET Push DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push , then . MUTE NAR MID LOW LOCK SET Appears DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Subaudible tones (Encoder function) D Subaudible tones q Select the channel that you want to set the subaudible tone to, such as the VFO, memory or Call channel. The subaudible tone frequency or code is indepen-

dently programmed into each mode or channel. w Push [SET] to enter the Set mode. e Push [SET] or [MONI] one or more times until the icon and Ct (for the CTCSS), the

(for the DTCS) or the peater tone) appear. icon and dt icon and rt (for the re-

r Rotate [DIAL] to select the desired subaudible fre-

quency or code. t Push any key other than [SET] or [MONI], to save the entry and exit the Set mode. NOTE: The subaudible tone encoder frequency can be temporarily set in a memory or Call channel. However, when another memory channel or VFO mode is select-

ed, the set frequency is cleared. To store the tone fre-

quency permanently, overwrite the channel information. Using the HM-133V z Select the mode or channel that you want to set the subaudible tones to, such as the VFO, memory or Call channel. The subaudible tone frequency or code is indepen-

dently programmed into each mode and channel. x Push [SET]

c Push [SET]

to enter the Set mode. or [ENT]

icon and Ct (for the CTCSS), the the and dt (for the DTCS) or the the repeater tone) appear. one or more times until icon icon and rt (for v Push [Y] or [Z] to select and set the desired subau-

dible tone frequency or code. Push and hold [Y] or [Z] to sequentially change the tones or codes. b Push [CLR]

to save the entry and exit the Set mode. Subaudible tone frequency list

(unit: Hz) 67.0 69.3 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 97.4 100.0 103.5 107.2 110.9 114.8 118.8 123.0 127.3 131.8 136.5 141.3 146.2 151.4 156.7 159.8 162.2 165.5 167.9 171.3 173.8 177.3 179.9 183.5 186.2 189.9 192.8 196.6 199.5 203.5 206.5 210.7 218.1 225.7 229.1 233.6 241.8 250.3 254.1 BASIC OPERATION 3 Setting the tone frequency MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Setting the DTCS code MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Setting the repeater tone frequency MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz 00 1 2 3 4 5 6 7 8 9 10 11 12 13 13 Push , then push the desired keys. Push , then or . 3 BASIC OPERATION D DTMF tones q When d is displayed in the 100 MHz digit, rst can-

cel the DTMF memory encoder. (p. 37) w Push [DTMF-S]

, then push the keys of the de-

sired DTMF digits. The function indicator lights green. 09, AD, M(E) and #(F) are selectable. Push [DTMF-S]

again to return to the normal keypad mode. The transceiver has ten DTMF memory channels for autopatch operation. See page 36 for details. The function indicator lights orange. D 1750 Hz tone The microphone has 1750 Hz tone capability, used as a ring tone when calling, and so on. z Push [FUNC]

x Push [TONE-1]

to transmit a 1750 Hz tone call signal for 1 second (approximately); hold down

[TONE-2]

to continuously transmit a 1750 Hz tone call signal. The function indicator automatically goes out. 14 4 REPEATER SETTING Frequency Offset When communicating through a repeater, the transmit frequency is shifted up or down from the receive fre-

quency. q Push [SET] to enter the Set mode. w Push [SET] or [MONI] until the icon and the fre-

quency offset appear. e Rotate [DIAL] to set the desired frequency offset. Push [V/MHz] one or more times, to toggle the fre-

quency step between 1 kHz and 1 MHz. r Push any key other than [SET] or [MONI], to save the selection and exit the Set mode. Using the HM-133V z Push [SET]

x Hold down [SET]

or [ENT]

and the frequency offset appear. to enter the Set mode. until the icon c Push [Y] or [Z] to set the desired offset. The frequency cannot be directly entered using the keypad. v Push [CLR]

to save the selection and exit the Set mode. Repeater Lockout This function helps prevent interference to other sta-

tions by inhibiting transmitting when a signal is re-

ceived. The transceiver has two inhibiting conditions, repeater and busy. q Push [

w While holding down [SET], push [

] to turn OFF the power.

] to turn ON the power and enter the Initial Set mode. e Push [SET] or [MONI] until RLO appears. r Rotate [DIAL] to select the Repeater Lockout func-

tion option of RP, BU or OFF. OF: The Repeater Lockout function is OFF. RP: Transmit is inhibited when a signal with an un-matched subaudible tone is received. BU: Transmit is inhibited when a signal is re-

ceived.

] to save the selection and exit the Initial Set t Push [

mode. 15 MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to enter the Set mode, MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz

MUTE NAR MID LOW LOCK SET

[SET]

DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz The Repeater Lockout function OFF (default) REPEATER OPERATION 4 Reversed Duplex function When the reversed duplex function is ON, the receive frequency shifts. (The transmit frequency shifts in normal duplex mode.) An example receive and transmit frequency is shown in the table below with the following settings:

Input frequency : 145.30 MHz Offset direction

: (Negative) Offset frequency : 0.6 MHz Reversed Rx frequency Tx frequency 145.30 MHz 144.70 MHz OFF ON 144.70 MHz 145.30 MHz q Push [SET] to enter the Set mode. w Push [SET] or [MONI] one or more times until REV appears. e Rotate [DIAL] to turn the reversed duplex mode ON or OFF. r Push any key other than [SET] or [MONI], to save the selection and exit the Set mode. Using the HM-133V z Push [SET]

x Push [SET]

c Push [Y] or [Z] to turn the reversed duplex mode to enter the Set mode. or [ENT]

until REV appears. ON or OFF. v Push [CLR]

Set mode. to save the selection and exit the Auto repeater (Only USA versions) The USA version automatically activates the repeater settings (DUP or DUP+ and tone encoder ON/OFF), when the operating frequency falls within the general repeater output frequency range, and deactivates them when outside of the range. D Setting the Auto Repeater function ON/OFF q Push [

w While holding down [LOCK] (SET), hold down [

] to turn OFF power.

] to turn ON the power and enter the Initial Set mode. e Push [SET] until RPT appears as shown below. r Rotate [DIAL] to turn the Auto Repeater function to R1, R2 or OFF. R1: auto repeater is ON, tone encoder is OFF. R2: auto repeater is ON, tone encoder is ON. t Push [

] to exit the Initial Set mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz The reversed duplex mode: OFF The reversed duplex mode: ON MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz The duplex icon blinks while the Reversed Duplex function is turned ON. Push to enter the Set mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Auto repeater function is turned OFF. Auto repeater function is ON, tone encoder is ON. Frequency range and offset direction Frequency range Duplex direction D 145.200145.495 MHz 146.610146.995 MHz 147.000147.395 MHz appears

+ appears 00 1 2 3 4 5 6 7 8 9 10 11 12 13 16 5 MEMORY OPERATION General description The transceiver has 207 memory channels including 6 scan edge memory channels (3 pairs), and 1 Call chan-

nel. These channels can be individually programmed with:

Operating frequency (p. 5) Duplex direction (p. 12) and offset (p. 15) Subaudible tone or tone squelch and tone frequency

(pp. 13, 3941) Skip setting* (p. 32)

[i.e.]: Programming 145.870 MHz into memory chan-

nel 20 via the front panel. Push [V/MHz]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate [DIAL] to set the frequency. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push [S.MW]. In addition, a total of 10 memory banks; A to J, are se-

lectable for use by groups, and so on.

*except for scan edge memory channels. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Programming a memory channel The VFO settings, including the Set mode contents such as subaudible tone frequency, and so on, can be programmed into a memory channel. q Set the desired frequency in the VFO mode. w Push [S.MW]. e Rotate [DIAL] to select the memory channel to be icon and the memory channel number blink. The programmed. If the selected channel is blank, only the memory channel number is displayed. r Hold down [MW] (S.MW) for 1 second to program. 3 beeps sound. The memory channel number increases, when continuing to hold down [MW] (S.MW) after pro-

gramming. CONVENIENT Memory programming can be performed in several ways. Example; Programming the memory channel to the same (or different) memory channel, memory chan-

nel to the Call channel, and so on. Using the HM-133V z Set the desired frequency in the VFO mode. x Push [FUNC]

. c Push [Y] or [Z] to select the memory channel to be icon and the memory channel number blink.

, and then push [MW]

The programmed. (direct numeric input cannot be used.) v Push [FUNC]

, and then hold down [MW]

for 1 second to program. 3 beeps sound and the VFO contents (including the subaudible tone frequency, and so on.) are programmed. The memory channel number increases, when after program-

continuing to hold down [MW]

ming. 17 Rotate [DIAL] to select the memory channel to be programmed. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Hold down [S.MW] for 1 second. MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Beep Beep Beep DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz

[i.e.]: Programming 145.870 MHz into the memory channel 20, using the microphone. Push . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push , and then . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push / . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push , and then hold down for 1 second. MUTE DIGITAL PRIO AO BUSY LOCK SET ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Beep Beep Beep DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET Memory channel selection D q Push [M/CALL] once or twice to select the memory Using the tuning dial mode. The icon appears. w Rotate [DIAL] to select the desired memory channel. Only programmed memory channels can be se-

lected. D Using [Y] or [Z] on the HM-133V z Push [MR]

x Push [Y] or [Z] to select and set the desired mem-

to select the memory mode. ory channel. Pushing [Y] or [Z] for 1 second activates a scan. If a scan starts, push [CLR]

to stop it. D Using the keypad on the HM-133V z Push [MR]

x Push [ENT]

to select the memory mode. to activate the keypad for numerical input. c Push three appropriate numeric keys to input a channel number. Push only 1 appropriate digit key, [1]

, and then push [M]

or

[3]

to select the scan edge channels. M and # can be used for A and B respectively. or [#]

, [2]

MEMORY OPERATION 5

[i.e.]: Selecting memory channel 2. Push [M/CALL] to select the memory mode. Appears MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Memory channel number Rotate [DIAL] to select the desired memory channel. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Selected memory channel

[i.e.]: Selecting memory channel 2. Push to select the memory mode. Appears MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Memory channel number Push to select the desired memory channel.

MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Selected memory channel

[i.e.]: Selecting memory channel 2. Push to select the memory mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY Appears ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Memory channel number Push , and then push . MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Selected memory channel 00 1 2 3 4 5 6 7 8 9 10 11 12 13 18 5 MEMORY OPERATION Copying memory contents This function copys a memory channels contents to the VFO, another memory or Call channel. This function is useful when searching for signals around the memory channel frequency, and for easy recalling the frequency offset, subaudible tone frequency, and so on. D Memory/Call channelVFO q Select the memory or Call channel to be copied. w Hold down [MW] (S.MW) for 1 second to copy the selected memory or Call channel contents to the VFO. The VFO mode is automatically selected. Using the HM-133V z Select the memory or Call channel to be copied. x Push [FUNC]

for 1 second, to copy the contents of selected memory or Call channel to the VFO. The VFO mode is automatically selected.

, and then hold down [MW]

19

[i.e.]: Copying memory channel 30 contents to the VFO. Push [M/CALL] to select the memory mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate [DIAL] to select the memory channel. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Hold down [MW] (S.MW) for 1 second. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz VFO mode

[i.e.]: Copying memory channel 30 contents to the VFO. Push to select the memory mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Select the memory channel. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push , and then hold down for 1 second. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz VFO mode D Memory/Call channelCall/memory channel q Select the memory or Call channel to be copied. w Push [S.MW]. e Rotate [DIAL] to select the target memory channel. C blinks when the Call channel is selected. Scan edge channels; 1A/1b, 2A/2b, 3A/3b, are also icon and indication blink. The selectable. r Hold down [MW] (S.MW) for 1 second, to copy the contents of selected memory or Call channel to the target memory. The targeted memory and copied contents are dis-

played. Using the HM-133V z Select the memory or Call channel to be copied. x Push [FUNC]

icon and indication blink, and the

, and then push [MW]

The VFO frequency is displayed. c Push [Y] or [Z] to select the target memory channel. C blinks when the Call channel is selected. Scan edge channels can also be selected. The keypad cannot be used for setting the chan-

nel. v Push [FUNC]

, and then hold down [MW]

for 1 second to copy the contents of selected memory or Call channel to the target memory. The targeted memory and copied contents are dis-

played. MEMORY OPERATION 5

[i.e.]: Copying memory channel 30 contents to chan-

nel 31. Select the memory channel. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push [S.MW]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate [DIAL] to select the target channel. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Hold down [MW] (S.MW) for 1 second. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz

[i.e.]: Copying memory channel 30 contents to chan-

nel 31. Select the memory channel. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push , and then push . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push / to select the target channel. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push , and then hold down for 1 second. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz 00 1 2 3 4 5 6 7 8 9 10 11 12 13 20 5 MEMORY OPERATION Programming channel names Each memory channel and the Call channel can be programmed with an alphanumeric channel name, for easy recognition. Names can be a maximum of 6 char-

acters see the table to the right, for the selectable characters.

(A)

(K)

(U)

(5) q Push [M/CALL] to select the memory mode. w Rotate [DIAL] to select the desired memory channel. e Hold down [ANM] (MONI) for 1 second to switch the channel name display. Two beeps sound. The name is displayed, if programmed. r Push [SET] to enter the channel name programming mode. t Rotate [DIAL] to select a character. y Push [SET] or [MONI] to move the cursor to the left The selected character blinks. or right. u Repeat steps t and y, until the desired channel name is completed. i Push any key other than [SET] or [MONI], to pro-

gram the name and exit the channel name program-

ming mode. To switch to the frequency display, hold down

[MONI] (ANM) for 1 second again. IMPORTANT!: While the channel name display mode is selected, and when [SET] is pushed, the channel name programming mode is always ac-

cessed. To access the Set mode, cancel the channel name display by holding down [MONI] (ANM) for 1 second. Using the HM-133V z Select the memory or Call channel to be assigned the memory name.

, and then push [ANM]

The name is displayed, if programmed. x Push [FUNC]

c Push [SET]

v Push [Y] or [Z] to select the desired character. b Push [SET]

The selected character blinks. or [ENT]

. to move the cursor to the left or right. n Repeat steps v and b until the desired channel names are completed. m Push [MW]

to program the name and exit the channel name programming mode.

, If desired, push [FUNC]

, and then push [ANM]

to return to the frequency display. 21

(B)

(L)

(C)

(M)

(D)

(E)

(N)

(O)

(F)

(P)

(V)

(W)

(X)

(Y)

(Z)

(6)

(7)

(8)

(9)

(space)

(0)

(G)

(H)

(I)

(J)

(Q)

(1)

(R)

(2)

(S)

(3)

(T)

(4)

[i.e.]: Programming CLUB into memory channel 5. Select memory channel 5, and then hold down [ANM] (MONI) for 1 second. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AOBUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push [SET]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AOBUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Channel name display

(The name is displayed, if programmed.) Rotate [DIAL] to select the character, and then push [SET] or [MONI] to move the cursor. PRIO AO BUSY SET ANM MONI DUP LOW PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET PRIO AO BUSY ANM MONI DUP LOW PRIO M/CALL SCAN V/MHz Repeat until the name is complete. Push any other keys than [SET] or [MONI]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz

[i.e.]: Programming CLUB into memory channel 5. Select memory channel 5, push then . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AOBUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AOBUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Channel name display

(The name is displayed, if programmed.) Push / to select the character, and then push or to move the cursor. PRIO AO BUSY SET ANM MONI DUP LOW PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET PRIO AO BUSY ANM MONI DUP LOW PRIO M/CALL SCAN V/MHz Push . Repeat until the name is complete. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Memory clearing Contents of programmed memories can be cleared

(blanked). q Push [V/MH z] to select the VFO mode. w Push [S.MW]. icon and the memory channel number The blink. e Rotate [DIAL] to select the memory channel to be cleared. Memory channels not yet programmed are blank. r Push [S.MW], and then sequentially hold down

[MW] (S.MW) again for 1 second This operation must be performed within 1.5 seconds. 3 beeps sound, and then the memory channel is cleared. icon and memory channel number blink. The When clearing the Call channel, the current VFO contents are automatically re-programmed into the Call channel. t Push any key other than [S.MW], to return to the VFO mode. NOTE: Be careful! the contents of cleared memo-

ries CANNOT be recalled. Using the HM-133V z Push [VFO] to select the VFO mode. x Push [FUNC]

c Push [Y] or [Z] to select the memory channel to be

, and then push [MW]

. cleared. The Memory channels not yet programmed are blank. icon and channel number blink. v Push [FUNC]

, and then push for 1 second. This operation must be performed within then hold down [MW]

then [MW]

[FUNC]

1.5 seconds. 3 beeps sound, and then the memory channel is cleared. icon and memory channel number blink. The When clearing the Call channel, the current VFO conditions are automatically re-programmed into the Call channel. b Push [CLR]

, to return to the VFO mode. MEMORY OPERATION 5

[i.e.]: Clearing memory channel 20. Push [V/MHz] to select the VFO mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push [S.MW]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate [DIAL] to select the memory channel. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push [S.MW], and within 1.5 seconds, hold down [MW] (S.MW) for 1 second again. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push any key other than [S.MW]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz

[i.e.]: Clearing memory channel 20. Push to select the VFO mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push then . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate to select the memory channel.

MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push then , and within 1.5 seconds, push then hold down for 1 second again. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz 00 1 2 3 4 5 6 7 8 9 10 11 12 13 22

[i.e.]: Setting memory channel 1 to bank A."

Push [SET]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push [SET] or [MONI] to select the BAK item. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate [DIAL] to select the desired bank. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz

[i.e.]: Setting memory channel 1 to bank A."

Push . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push or to select the BAK item. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate to select the desired bank.

MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz 5 MEMORY OPERATION Memory bank setting q Push [M/CALL] to select the memory mode, and then rotate [DIAL] to select the desired memory channel. indication blinks. w Push [SET] to enter the Set mode. e Push [SET] or [MONI] until BAK appears. r Rotate [DIAL] to select the desired bank to be set. t Push any key other than [SET] or [MONI] to assign the channel into the selected bank and exit the Set mode. Using the HM-133V z Push [MR]

, and then select the desired memory channel using [Y], [Z] or keypad. x Push [SET]

c Push [SET]

v Push [Y] or [Z] to select the desired bank to be to enter the Set mode. or [ENT]

indication blinks. until BAK appears. set. b Push [MW]

to assign the channel into the se-

lected bank and exit the Set mode. 23 Memory bank selection The IC-2300H has a total of 10 banks (A to J). Regular memory channels; 0 to 199, and scan edges; 1A to 3B can be assigned into the desired bank for easy memory management. q Push [M/CALL] to select the memory mode. w Push [BANK] to select the memory bank mode. e Rotate [DIAL] to select the desired bank, A to J."

Banks that contain no memory channels are icon and the bank letter blink. The skipped. r Push [BANK] to set the bank. The bank letter stops blinking. t Rotate [DIAL] to select the desired memory channel. The channel number is not displayed in the memory bank mode. y To return to the regular memory mode, push [BANK]

twice. Using the HM-133V z Push [MR]

x Push [BANK]

to select the memory mode. to select the memory bank mode. The icon and the bank letter blink. c Push [Y] or [Z] to select the desired bank, A to J. Banks that contain no memory channels are skipped. to set the bank. The bank letter stops blinking. v Push [MW]

b Push [Y] or [Z] to select the desired memory chan-

nel. The channel number is not displayed in the memory bank mode. n To return to the regular memory mode, push

[BANK]

, and then push [CLR]

. MEMORY OPERATION 5

[i.e.]: Selecting the memory bank A."

Push [BANK] to select the memory bank mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate [DIAL] to select the desired bank. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push [BANK] again to set the bank. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz

[i.e.]: Selecting the memory bank A."

Push to select the memory bank mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to select the desired bank.

MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to set the bank. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz 00 1 2 3 4 5 6 7 8 9 10 11 12 13 24 5 MEMORY OPERATION Transferring bank links The link between a memory channels and it's assigned bank can be transferred to another bank. q Push [M/CALL] to select the normal memory mode. The icon and the channel number appear. w Push [BANK] to select the memory bank mode. e Rotate [DIAL] to select the desired bank, A to J. Banks that contain no memory channels are icon and the bank letter blink. The skipped. r Push [BANK] to set the bank. The bank letter stops blinking. t Rotate [DIAL] to select the desired memory channel to transfer. y Push [SET] to enter the Set mode. u Push [SET] or [MONI] until BAK appears. i Rotate [DIAL] to select the destination bank. o Push any key other than [SET] or [MONI] to transfer Bank initial appears. and exit the Set mode. Using the HM-133V z Push [MR]

x Push [BANK]

to select the memory mode. desired memory bank, and then push [CLR]

select the bank.

, push [Y] or [Z] to select the to c Push [Y] or [Z] to select the desired bank link to be transferred. v Push [SET]

b Push [SET]

n Push [Y] or [Z] to select the destination bank. m Push [CLR]

to enter the Set mode. or [ENT]

Bank initial appears. to transfer and exit the Set mode. until BAK appears. 25

[i.e.]: Transffering the link of bank A to bank C. Push [BANK] to select the memory bank mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate [DIAL] to select the desired bank. DIGITAL PRIO AO BUSY Push [SET] to enter the Set mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push [SET] or [MONI] to select the BAK item. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate [DIAL] to select the bank to be transffered.

(Or, select - - to erase.) MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push any key other than [SET] or [MONI]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz

[i.e.]: Transffering the contents of bank A to bank C. Push to select the memory bank mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to select the desired bank.

DIGITAL PRIO AO BUSY Push to enter the Set mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to select the BAK item.

MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to select the bank to be transffered.

(Or, select - - to erase.)

MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MEMORY OPERATION 5 Erasing bank links The link between a memory channel and it's assigned bank can be erased. INFORMATION: Even if the memory bank links are erased, the memory channel contents remain pro-

grammed. q Push [M/CALL] to select the normal memory

[i.e.]: Erasing the link of bank A."

Push [BANK] to select the memory bank mode MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate [DIAL] to select the desired bank. DIGITAL PRIO AO BUSY mode. The icon and the channel number appear. w Push [BANK] to select the memory bank mode. e Rotate [DIAL] to select the desired bank, A to J."

Banks that contain no memory channels are icon and the bank letter blink. The skipped. r Push [BANK] to set the bank. t Rotate [DIAL] to select the desired memory channel icon and bank letter stop blinking. The to delete. The bank letter also appears. y Push [SET] to enter the Set mode. u Push [SET] or [MONI] until BAK appears. i Rotate [DIAL] to select . o Push any key other than [SET] or [MONI] to erase the selected memory channel link and then exit the Set mode. Using the HM-133V z Push [MR]

x Push [BANK]

to select the memory mode.

, push [Y] or [Z] to select the de-

sired memory bank, and then push [CLR]

. c Push [Y] or [Z] to select the desired bank link to be erased. to enter the Set mode. or [ENT]

v Push [SET]

b Push [SET]

n Push [Y] or [Z] to select . m Push [CLR]

Bank initial appears. to erase and exit the Set mode. until BAK appears. Push [SET] to enter the Set mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push [SET] or [MONI] to select the BAK item. DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN Rotate [DIAL] to select . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz

[i.e.]: Erasing the link of bank A. Push to select the memory bank mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to select the desired bank.

DIGITAL PRIO AO BUSY Push to enter the Set mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to select the BAK item.

MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to select .

MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz 00 1 2 3 4 5 6 7 8 9 10 11 12 13 26 6 CALL CHANNEL OPERATION Call channel selection Push [M/CALL] once or twice to select the Call channel. C appears instead of a memory channel number. Push [M/CALL] to return to the memory mode, or push

[V/MH z] to select the VFO mode. INFORMATION When the VFO mode is selected from the Call channel, a small c appears instead of memory channel number. Push [M/CALL] once or twice to select the Call channel. MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY Appears ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Using the HM-133V Hold down [CALL]

for 1 second to select the Hold down for 1 second to select the Call channel. Call channel. Push [MR]

to select the memory mode, or push [VFO] to select the VFO mode. MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY Appears ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Copying Call channel contents The contents of Call channel can be copied to another channel or to the VFO. q Push [M/CALL] one or more times to select the Call channel. C appears. w To copy the Call channel contents to a Memory channel, push [MW] (S.MW), and then rotate [DIAL]

to select the memory channel to be copied. The icon and memory channel number blink. e Hold down [MW] (S.MW) for 1 second to copy. If channel names have been programmed into the Call channel, the names are also copied. To copy to the VFO, hold down [MW] (S.MW) for 1 second. Using the HM-133V z Hold down [CALL]

Call channel. for 1 second to select the x Push [FUNC]

, and then push

[Y] or [Z] to select the memory channel to copy the contents.

, then [MW]

c Push [FUNC]

, then hold down [MW]

for 1 second to copy when a momentary push was used in the previous step. If channel names have been programmed into the Call channel, the names are also copied. To copy to the VFO, push [FUNC]

hold down [MW]

for 1 second.

, and then 27

[i.e.]: Copying the Call channel (145.000 MHz) to memory channel 2. Push [S.MW]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate [DIAL] to select the memory channel. The selected memory channel. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Hold down [S.MW] for 1 second. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz

[i.e.]: Copying the Call channel (145.000 MHz) to memory channel 2. Push then . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to select the memory channel.

MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz The selected memory channel. Push , then hold down for 1 second. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Programming a Call channel Operating frequency, duplex setting, subaudible tone setting (tone encoder or tone squelch ON/OFF and its frequency) and channel names can be also pro-

grammed into the Call channel. q Push [V/MH z] to select the VFO mode, and set the desired frequency. w Push [MW] (S.MW). e Rotate [DIAL] to select the Call channel r Hold down [MW] (S.MW) for 1 second icon and C blink. The 3 beeps sound, and then the transceiver automati-

cally returns to the VFO mode. Using the HM-133V z Set the desired frequency in the VFO mode. Push [VFO] to select the VFO mode. Set the frequency. Set other data as desired. x Push [FUNC]

c Push [Y] or [Z] to select the Call channel. v Push [FUNC]

, and then [MW]

then [MW]

. for 1 second to pro-

gram. 3 beeps sound, and then the transceiver automati-

cally returns to the VFO mode. CALL CHANNEL OPERATION 6

[i.e.]: Programming 145.120 MHz into the Call channel. Push [V/MHz] to select the VFO mode. 00 MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate [DIAL] to set the frequency. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push [M/CALL], and then push [S.MW]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate [DIAL] until large C appears. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Hold down [MW] (S.MW) for 1 second. MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Beep Beep Beep DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz

[i.e.]: Programming 145.120 MHz into the Call channel using the microphone. Push to select the VFO mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to set the frequency. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push , and then push . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push / until large C appears. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push then hold down for 1 second. MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Beep Beep Beep DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz 1 2 3 4 5 6 7 8 9 10 11 12 13 28 7 SCAN OPERATION Scan types Scanning automatically searches for signals making it easier to locate new stations for contact or listening pur-

poses. FULL SCAN Band edge Band edge Scan Jump Repeatedly scans all fre-

quencies over the entire band. Used as the simplest scan without any prelimi-

nary settings. There are 3 scan types and 4 resume conditions to suit your operating needs. PROGRAMMED SCAN Band edge Scan edges Band edge Scan Jump Repeatedly scans between two programmed frequen-

cies. Used to checking for frequencies within a speci-

ed range, such as re-

peater output frequencies, and so on. 3 pairs of scan edges are programmable. MEMORY SCAN SKIP M 2 M 3 M 1 M 0 M 199 M 6 M 5 M 4 SKIP Repeatedly scans memory channels, except those set as skip channels. Used for often-called channels and for bypassing normally busy channels such as re-

peater frequencies. SCAN RESUME FUNCTION (p. 33) Receiving a signal Pause scan Timer scan Resume time Pausing 11 resume options are selectable; 7 timer scans and a pause scan. When receiving a signal, the pause scan pauses un-

til the signal disappears;

timer scans pause for the speci c period of time. NOTE: A tone scan function is selectable to search for subaudible tones (Example: When you want to nd a sub-

audible tone frequency that is necessary to open a repeater). See page 42 for details. 29 Preparation Scan start/stop D If desired, set the scan resume option (p. 33), program the scan edges (p. 31), program 2 or more memory channels (p. 17), set the skip channels (p. 32). Operation For full/programmed scan:

D q Select the mode or bank. Push [V/MH z] to select the VFO mode. For memory scan:

Push [M/CALL] to select the memory mode. For bank scan:

Push [BANK], and then rotate [DIAL] to select the desired bank. w Set the squelch to the point where the noise is just muted. e Hold down [SCAN] (V/MHz) for 1 second to start the scan. Rotate [DIAL] to change the scanning direction. The scan type blinks in the memory channel read-

out. r Push [SET] to switch between a full scan and a pro-

grammed scan (P1, P2 and P3). Push [V/MH z] to cancel the scan. For a full/programmed scan:

Using the HM-133V z Select the mode or bank. Push [VFO]

For a memory scan:

Push [MR]

For a bank scan:

Push [BANK]

to select the VFO mode. to select the memory mode.

, and then push[Y] or [Z] to select the desired bank. x Set the squelch to the point where noise is just mut-

ed. to start the scan. c Push [SCAN]

Hold down [Y] or [Z] for 1 second also starts the scan. v Push [SET]

to switch between a full scan and programmed scan (P1, P2 and P3). b Push [SCAN]

or [CLR]

to stop the scan. SCAN OPERATION 7

[i.e.]: Starting a memory scan. Push [M/CALL]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Hold down [SCAN] (V/MHz) for 1 second. MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz During memory scan During a full scan MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push [SET] to select a full, band or programmed scan (P1, P2 and P3) in sequence. During a programmed scan MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Scan edge channel display. P1 stands for 1A/1b P1 to P3 are selectable when they are programmed, and switched with [SET]. During a memory or bank scan MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz

[i.e.]: Starting a memory scan. Push . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push . MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz During memory scan 00 1 2 3 4 5 6 7 8 9 10 11 12 13 30 7 SCAN OPERATION Scan edges programming Scan edges can be programmed in the same manner as memory channels. Scan edges are programmed into scan edges, 1A/1b to 3A/3b, in memory channel sheet. q Set the desired edge frequency in the VFO mode:

w Push [MW] (S.MW). e Rotate [DIAL] to select one of scan edge channels, icon and channel number blink. The 1A, 2A or 3A. r Hold down [MW] (S.MW) for 1 second to store it. 3 beeps sound and the transceiver automatically returns to the VFO mode. Scan edge 1b, 2b or 3b is automatically selected when continuing to hold down [MW] (S.MW) after programming. t To program a frequency for the other pair of scan edges, the 1b, 2b or 3b, repeat steps q through r. If the same frequency is programmed into a pair of scan edges, the programmed scan cannot start. Using the HM-133V z Set the desired frequency in the VFO mode. x Push [FUNC]

c Push [Y] or [Z] to select the scan edge channels,

, and then [MW]

. 1A, 2A or 3A. v Push [FUNC]

, and then hold down [MW]

for 1 second to program. 3 beeps sound and the VFO mode is automatically selected.

[i.e.]: Programming 145.300 MHz into scan edge 1A. Push [V/MHz]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate [DIAL] to set the frequency. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push [S.MW]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate [DIAL] to select the scan edge channel. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Hold down [MW] (S.MW) for 1 second. MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Beep Beep Beep DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz

[i.e.]: Programming 145.800 MHz into scan edge 1b. Push . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push . The memory channel number advances to the next scan edge channel, 1b, 2b or 3b, when continuing to push [MW]

after programming. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz b To program a frequency for the other scan edge channels, repeat steps z to v. Push then . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push / . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push then hold down for 1 second. MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Beep Beep Beep DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz 31 Skip channel setting The memory skip function speeds up scanning by not scanning those memory channels set as skip channels. Set skip channels as follows. q Push [M/CALL] to select the memory mode, and then select the memory channel to be skipped. w Push [SET] to enter the Set mode. e Push [SET] or [MONI] until CHS appears. r Rotate [DIAL] to select ON."

~ appears : The channel is skipped while scan-

ning. t Push any key other than [SET] or [MONI], to exit the Set mode. Using the HM-133V z Push [MR]

to select the memory mode, and then push [Y] or [Z] to select the channel to be skipped. x Push [SET]

c Push [SET]

v Push [Y] or [Z] to select ON."

b Push [CLR]

to enter the Set mode. or [ENT]

until CHS appears. to save the selection and exit the Set mode. NOTES:

The Set mode cannot be accessed when memory names are displayed. To set the skip option, return to the frequency display by holding down [MONI] (ANM) on the front panel for 1 second, or push [FUNC]

then [MONI]

(on the HM-133V) to cancel the channel name display, and then set the Skip function as described above. SCAN OPERATION 7

[i.e.]: Setting memory channel 20 as the skip channel. Push [SET] to enter the Set mode. 00 MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push [SET] or [MONI] to select the CHS item. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate [DIAL] to select ON. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz The memory channel 20 is set as a skip channel.

[i.e.]: Setting memory channel 20 as the skip channel, using the HM-133V. Push to enter the Set mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to select the CHS item.

MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to select ON.

MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz The memory channel 20 is set as a skip channel. 1 2 3 4 5 6 7 8 9 10 11 12 13 32 7 SCAN OPERATION Scan Resume function Various pause and timer options can be selected with the Scan Resume function. The selected resume op-

tion is also used for Priority Watch. (p. 35) q Push [SET] to enter the Set mode. w Push [SET] or [MONI] until SCT or SCP ap-

pears. e Rotate [DIAL] to set the desired timer:

SCP-HO SCP-2"SCP-20 : The scan pauses for 2 to 20 seconds, when a signal is received.

: When a signal is received, the scan pauses until it disappears.

: The scan pauses, then re-

sumes 0 to 5 seconds after the signal disappears.

: The scan continues to pause, even if the signal disappears. SCT-0"SCT-5 SCT-HO r Push any keys other than [SET] or [MONI] to exit the Set mode. DIGITAL PRIO AO BUSY When a signal is received, the scan pauses until it disappears. ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY The scan will resume 5 seconds after the signal disappears. ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET Using the HM-133V z Push [SET]

x Push [SET]

to enter the Set mode. or [ENT]

until SCT or SCP appears. c Push [Y] or [Z] to select the scan resume option. v Push [CLR]

See step e above for details. to exit the Set mode. NOTE: The Set mode cannot be accessed when memory names are displayed. To set the scan re-

sume option, return to the frequency display by hold-

ing down [MONI] (ANM) on the front panel for 1 sec-

ond, or push [FUNC]

(on the HM-133V) to cancel the channel name display, and then set the option as described on above. then [MONI]

33 MEMORY CHANNEL WATCH While operating on a VFO frequency, Priority Watch checks for a signal on the selected memory channel every 5 seconds. 5 seconds VFO frequency MEMORY SCAN WATCH While operating on a VFO frequency, Priority Watch sequentially checks for signals on each memory channel. The memory skip func-

tion is useful to speed up the scan. CALL CHANNEL WATCH While operating on a VFO frequency, Priority Watch checks for signals on the Call channel every 5 sec-

onds. 125 milliseconds Memory channel 125 milliseconds 5 seconds SKIP VFO frequency Mch 1 Mch 2 Mch 3 Mch 199 5 seconds 125 milliseconds VFO frequency Call channel 8 PRIORITY WATCH Priority Watch types IC-2300H has three types of Priority Watch, to suit your needs. You can transmit on the VFO frequency, even while Priority Watch is functioning. The watch resumes, depending on the selected scan resume function. See the page 33 for details. NOTE: If the pocket beep function is activated, the transceiver automatically turns ON the Tone Squelch function, when Priority Watch starts. 34 Priority watch operation q Select the VFO mode, and then set the operating frequency. w Set the watching channel. For a memory channel watch:

Push [M/CALL] to select the memory mode, and then rotate [DIAL] to select the desired memory channel. For a memory scan watch:

Select the memory mode, and then hold down

[SCAN] (V/MHz) for 1 second to start the memory scan. For a Call channel watch:

Push [M/CALL] once or twice, to select the Call channel. e Hold down [M/CALL] (PRIO) for 1 second to start the priority watch. The PRIO icon appears. The transceiver checks the memory channel or Call channel every 5 seconds. When a signal is received on the priority channel, the watch pauses. The watch resumes depending on the selected scan resume condition. (p. 33) When the watch is paused, push [M/CALL] to man-

ually resume it. r Push [M/CALL] to cancel the Priority Watch. The transceiver automatically returns to the VFO mode. Using the HM-133V z Select the VFO mode, and then set the operating frequency. x Set the watching channel. For a memory channel watch:

Push [MR]

memory channel. then [Y] or [Z], to select the desired For a memory scan watch:

Push [MR]

memory scan.

, and then push [SCAN] to start the for 1 second to select the For a call channel watch:

Hold down [CALL]

Call channel. c Push [PRIO]

to start the watch. The transceiver checks the memory or Call channel every 5 seconds. The watch resumes depending on the selected scan resume option. (p. 33) When the watch is paused, push [PRIO]

[CLR]

, to manually resume it. or v Push [CLR]

to cancel the watch. PRIORITY WATCH 8

[i.e.]: The memory channel watch on memory channel 20. Push [M/CALL]. 00 MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate [DIAL] to select the desired memory channel. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Hold down [PRIO] (M/CALL) for 1 second. MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz The watch checks for a signal on memory channel 20, every 5 seconds.

[i.e.]: The memory channel watch on memory channel 20. Push . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to select the desired memory channel.

MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push . MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz The watch checks for a signal on memory channel 20, every 5 seconds. 1 2 3 4 5 6 7 8 9 10 11 12 13 35 9 DTMF MEMORY ENCODER Programming a DTMF code DTMF codes are used for autopatching, controlling other equipment, and so on. IC-2300H has up to 16 DTMF memory channels (d0dF) for up to 24 digits often-used DTMF codes . q Hold down [OPT] (BANK) for 1 second to enter the Option Set mode. w If necessary, push [SET] or [MONI] to select DTM."

e Rotate [DIAL] to turn ON the DTMF encoder. r Push [BANK] to enter the DTMF memory mode. The DTMF memory channel display blinks. If desired, push [BANK] again to return to the Op-

tion Set mode. t Rotate [DIAL] to select a desired blank DTMF mem-

ory channel. The DTMF memory channel display blinks. y Push [SET] or [MONI] to enter the DTMF memory programming mode. The rst digit ( ) blinks. u Rotate [DIAL] to select the desired character. i Push [MONI] to set the character and select the next digit. Push [SET] to move the cursor to the left, push

[MONI] to move the cursor to the right. o Repeat steps u and i, to set the desired DTMF code sequence. When the 6th character is set, the indicator displays the next blank digit group.

!0 Push any key other than [SET] or [MONI], to save the channel and exit the DTMF memory program-

ming mode. Using the HM-133V z Hold down [OPTION]

Option Set mode. for 1 second to enter the x If necessary, push [MR]

c Push [Y] to turn ON the DTMF encoder. v Push [SET]

If desired, push [OPTION]

to select DTM. to enter the DTMF memory mode. to return to the Op-

tion Set mode. b Push [Y] or [Z] to select a desired blank DTMF memory channel. The DTMF memory channel display blinks. n Sequentially push the keys (09 or A to F), to set the desired DTMF code sequence. A: [A]

C: [C]

E: [M]

B: [B]

D: [D]

F: [#]

When the 6th character is set, the indicator displays the next blank digit group. m Push [Y] or [Z] to save the channel.

, Push [VFO]

ming mode. to exit the DTMF memory program-

36

[i.e.]: Programming 5428AB453 into the DTMF mem-

ory channel d4. Hold down [OPT] (BANK) for 1 second. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN Rotate [DIAL] to turn ON the DTMF encoder. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN Push [BANK]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN Rotate [DIAL]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN Push [SET], and then rotate [DIAL]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN Repeat until the code is complete. Push any key other than [SET] or [MONI]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz

[i.e.]: Programming 54A2F into the DTMF memory channel d4. Push once or twice. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN Push to turn ON the DTMF encoder. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN Push . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN Push to select the desired blank channel.

MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN Sequentially push . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN Push . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Transmitting a DTMF code Automatic transmission (DTMF memory) D q Hold down [OPT] (BANK) for 1 second to enter the Option Set mode. w If necessary, push [SET] or [MONI] to select DTM. e Rotate [DIAL] to turn ON the DTMF encoder. r Push [BANK] to enter the DTMF memory mode. The DTMF memory channel display blinks. If desired, push [BANK] again to return to the Op-

tion Set mode. t Rotate [DIAL] to select a desired blank DTMF mem-

ory channel. The DTMF memory channel display blinks. y Push any key other than [SET] or [MONI], to save the selection and exit the DTMF memory mode. d appears in the 100 MHz digit. u Push [PTT]. The selected DTMF code is transmitted. D Transmitting a DTMF memory using the HM-133V z Push [FUNC]

then [DTMF]

to turn ON the DTMF memory encoder. d appears in the 100 MHz digit. x Push [DTMF-S]

direct selection. The function LED on the microphone lights green. to turn ON the DTMF memory c Push a desired DTMF channel number. The selected DTMF code is automatically transmit-

ted without pushing [PTT]. NOTE: When the pushed channel number is not as-

signed a DTMF code, the previously transmitted DTMF memory code is transmitted. v Push [DTMF-S]

again to turn OFF the DTMF memory direct selection. The function LED on the microphone goes out. b Push [FUNC]

DTMF MEMORY ENCODER 9

[i.e.]: Transmitting the DTMF code in the DTMF mem-

ory channel d4. Hold down [OPT] (BANK) for 1 second. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Rotate [DIAL] to turn ON the DTMF encoder, and then push [BANK]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN Rotate [DIAL], and then push any key other than [SET] or [MONI]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push [PTT]. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Transmitting the DTMF code. Beep Beep Beep

[i.e.]: Transmitting the DTMF code in the DTMF mem-

ory channel d4. Push then . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push , and then push a desired DTMF channel number. MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Beep Beep Beep then [D-OFF]

to turn OFF the Transmitting the DTMF code. DTMF memory encoder. D Manual transmission using the HM-133V z If necessary, push [FUNC]

then [D-OFF]

to turn OFF the DTMF memory encoder. x Push [DTMF-S]

to turn ON the DTMF direct se-

lection. The function LED on the microphone lights green. c Push one of A to F keys, and then push the desired DTMF keys; 09 or A to F.

[i.e.]: Transmitting the DTMF code 54A2F. Push and then, sequentially push . MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Transmitting the DTMF code. Beep Beep Beep B: [B]

D: [D]

F: [#]

A: [A]

C: [C]

E: [M]

Automatically transmits without pushing [PTT]. The rst code entered may not be transmitted because transmitting takes 400 milliseconds to start. Then the DTMF code transmission starts from the 2nd code. v Push [DTMF-S]

direct selection. The function LED on the microphone goes out. again to turn OFF the DTMF 00 1 2 3 4 5 6 7 8 9 10 11 12 13 37 9 DTMF MEMORY ENCODER DTMF TX speed The transmitting speed of DTMF code can be set to ac-

commodate your operating needs.

] for 1 second to turn OFF the power. q Hold down [

w While holding down [LOCK] (SET) and [

] for 1 second, to turn ON the power to enter the Initial Set mode. e Push [SET] or [MONI] until DTD appears. r Rotate [DIAL] to select the desired transmitting speed, as shown in the table below.

] to exit the Initial Set mode. t Push [

MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz The display shows the fastest DTMF speed is selected. DISPLAY DTD- 1 DTD- 2 DTD- 3 DTD- 5 INTERVAL 100 milliseconds 200 milliseconds 300 milliseconds 500 milliseconds SPEED 5.0 cps 2.5 cps 1.6 cps 1.0 cps cps=characters/second 38 POCKET BEEP AND TONE SQUELCH 10 Pocket beep operation This function uses subaudible tones as calling, and can be used as a common pager to inform you that some-

one has called while you were away from the trans-

ceiver. D Waiting for a call from the speci c station q Set the operating frequency. w Push [SET] to enter the Set mode. e Set the tone frequency, or DTCS code and DTCS polarity. r Push any key other than [SET] or [MONI] to exit the Set mode. t Push [TONE] one or more times until is displayed, to respectively turn ON the pocket beep with tone squelch or DTCS squelch. or y When a signal with the matched tone is received, icon blinks. beep tones and the The beeps sound for 30 seconds and the icon blinks. To manually stop the beeps and blinking, push any key. When the beep tones are not manu-

icon continues blinking until ally stopped, the

[PTT] is pushed. u Push [PTT] to answer. The the pocket beep function. icon disappears and automatically cancels i Push [TONE] one or more times until the icon or icon disappears, to cancel the tone or the the DTCS Squelch function. Using the HM-133V z Set the operating frequency. x Push [SET]

c Set the tone frequency, or DTCS code and DTCS to enter the Set mode. polarity. Push [CLR]

v Push [FUNC]

[DTCSS]

beep with tone squelch or DTCS squelch. to exit the Set mode.

, and then push [TSQLS]

or

, to respectively turn ON the pocket b When the matched tone is received, the transceiver emits the beep tones for 30 seconds and the icon blinks. n Push [PTT] to replay, or push [CLR]

to stop the beeps and ashing. The icon automatically disappears and cancels the pocket beep function. Push [SET] to enter the Set mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push [SET] or [MONI] to select the item, and then rotate [DIAL] to set the option or value. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Setting the tone frequency Setting the DTCS code MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Setting the DTCS polarity Push any key other than [SET] or

[MONI] to exit the Set mode. Push [TONE] one or more times to turn ON the Pocket Beep function. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Appears when the pocket beep with tone squelch is activated. Appears when the pocket beep with DTCS squelch is activated. When a signal with the matched tone is received... MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY Beep Beep Beep ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to enter the Set mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to select the item, and then push to set the option or value.

MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Setting the tone frequency Setting the DTCS code MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz m To cancel the tone squelch or DTCS Squelch func-

Setting the DTCS polarity Push to exit the Set mode. tion, push [FUNC]

The icon or then [T-OFF]

icon disappears

. Push then or to turn ON the Pocket Beep function. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Appears when the pocket beep with tone squelch is activated. Appears when the pocket beep with DTCS squelch is activated. 00 1 2 3 4 5 6 7 8 9 10 11 12 13 39 10 POCKET BEEP AND TONE SQUELCH Waiting for a call from the speci c station (continued) D Selectable tone frequencies 131.8 136.5 141.3 146.2 151.4 110.9 114.8 118.8 123.0 127.3 94.8 97.4 100.0 103.5 107.2 79.7 82.5 85.4 88.5 91.5 67.0 69.3 71.9 74.4 77.0 156.7 159.8 162.2 165.5 167.9 171.3 173.8 177.3 179.9 183.5 186.2 189.9 192.8 196.6 199.5

(unit: Hz) 229.1 233.6 241.8 250.3 254.1 203.5 206.5 210.7 218.1 225.7 NOTE: IC-2300H has 50 tone frequencies and their spacing is consequently narrow, compared to units hav-

ing 38 tones. Therefore, some tone frequencies may re-

ceive interference from adjacent tone frequencies. D Calling a waiting station using pocket beep A subaudible tone matched with the stations CTCSS tone frequency or 3-digit DTCS code with polarity is necessary. Use the tone squelch on the next page or a subaudible tone encoder. (pp. 13, 41) 40 Tone/DTCS squelch operation The tone squelch or DTCS squelch opens when a sig-

nal with the same pre-programmed subaudible tone or DTCS code is received. The reverse tone or DTCS squelch is convenient when you want to ignore the speci c signal. The transceiver closes the squelch when a signal with the same pre-

programmed subaudible tone or code is received. q Set the operating frequency. w Push [SET] to enter the Set mode. e Set the tone frequency, or DTCS code and DTCS polarity. r Push any key other than [SET] or [MONI] to exit the Set mode. t Push [TONE] one or more times to select the de-

sired tone or code. y Operate the transceiver in the normal way; push

: Tone squelch

: DTCS squelch

: Reverse tone squelch

: Reverse DTCS squelch

[PTT] to transmit; release [PTT] to receive. To manually open the squelch, push [MONI]. When the tone or DTCS is in use:

When a matched tone is received, the squelch opens and audio is heard. If the signal includes an unmatched tone, the squelch does not open. However, the S/RF meter shows the signal strength. When the reverse tone or DTCS is in use:

When a matched tone is received, the squelch re-

mains closing. If the signal includes a matched tone, the squelch does not open. However, the S/RF meter shows the signal strength. u To cancel the tone or DTCS squelch, push [TONE]

one or more times, until the tone icon disappears. Using the HM-133V z Set the operating frequency. x Program the CTCSS tone frequency or DTCS code in the Set mode. (p. 46) c Push [FUNC]

then [TSQL]

or DTCS]

, to turn ON the tone squelch or DTCS squelch. v When a matched tone is received, the squelch opens and audio is heard. If the signal includes an unmatched tone, the squelch does not open. However, the S/RF meter shows the signal strength. To manually open the squelch, push [MONI]

b Operate the transceiver in the normal way ;push

[PTT] to transmit; release [PTT] to receive. n To cancel the tone squelch, push [FUNC]

then

[T-OFF]

The

. icon or icon disappears POCKET BEEP AND TONE SQUELCH 10 Push [SET] to enter the Set mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push [SET] or [MONI] to select the item, and then rotate [DIAL] to set the option or value. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Setting the tone frequency Setting the DTCS code MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Setting the DTCS polarity Push any key other than [SET] or

[MONI] to exit the Set mode. Push [TONE] one or more times to turn ON the tone squelch or DTCS. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Appears when the tone squelch is activated. Appears when the DTCS squelch is activated. Push to enter the Set mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push to select the item, and then push to set the option or value.

MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Setting the tone frequency Setting the DTCS code MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Setting the DTCS polarity Push to exit the Set mode. Push then or to turn ON the tone squelch or DTCS. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Appears when the tone squelch is activated. Appears when the DTCS squelch is activated. 00 1 2 3 4 5 6 7 8 9 10 11 12 13 41 10 POCKET BEEP AND TONE SQUELCH Tone scan By monitoring a signal that is being operated with the pocket beep, tone or DTCS Squelch function turned ON, you can determine the tone frequency or DTCS code necessary to open the squelch. q Set the channel to be checked for a tone frequency or code. w Push [TONE] one or more times to select the tone type to be checked. One of the icons e Hold down [T-SCAN] (TONE) for 1 second to start appear. or

, the tone scan. Rotate [DIAL] to change the scanning direction. r When the CTCSS tone frequency or DTCS code is detected, the squelch opens and the detected tone frequency is temporarily programmed into the mem-

ory or Call channel. The scan pauses when a CTCSS tone frequency or DTCS code is detected. The detected CTCSS tone frequency or DTCS code is used for the tone encoder or decoder, depending on the tone condition or type selected in step w.

: CTCSS tone encoder

- No icon : Cannot be used for operation.

t Push [V/MH z] to cancel the scan.

: CTCSS tone encoder/decoder

: DTCS tone encoder/decoder

: DTCS tone encoder

Using the HM-133V z Set the channel to be checked for a tone frequency. x Select the tone type to be checked. then push; [TONE]

Push [FUNC]

for tone squelch; [DTCS]

for repeat-

for er tone; [TSQL]

DTCS squelch. c Push [FUNC]

then [T-SCAN]

to start the tone scan. v When the tone frequency is matched, the squelch opens and the tone frequency is programmed into the selected memory or Call channel. b Push [CLR]

to cancel the scan. NOTE: The detected tone frequency is temporarily programmed when a memory or Call channel is se-

lected. However, this will be cleared when the memory or Call channel is re-selected. 42

[i.e.]: Checking for 145.680 MHz. the tone frequency on the MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push [TONE] one or more times to select the tone type. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY Appears ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Hold down [T-SCAN] (TONE) for 1 second. MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz During CTCSS tone scan

[i.e.]: Checking for 145.680 MHz. the tone frequency on the MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push then to select the tone type. Appears DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK SET ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Push then . MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz During CTCSS tone scan Set mode Set mode operation q Push [SET] to enter the Set mode. w Push [SET] or [MONI] to select the desired item. e Rotate [DIAL] to set the option or value. r Push any key other than [SET] or [MONI], to exit the Set mode. Set mode items

: [MONI]

: [SET]

Repeater tone frequency Tone squelch frequency DTCS code DTCS polarity Frequency offset Reverse mode Tuning step Scan stop timer Scan resume timer Display dimmer Auto dimmer SET MONI SET MONI SET MONI SET MONI SET MONI SET MONI SET MONI SET MONI SET MONI SET MONI SET MONI OTHER FUNCTIONS 11 Using the HM-133V z Push [SET]

x Push [SET]

to enter the Set mode. or [ENT]

, to select the desired item. c Push [Y] or [Z] to select the option or value. v Push [CLR]

to exit the Set mode. Appears only when accessing the Set mode from the memory mode. Select the subaudible tone needed to access the repeater. Select the CTCSS tone frequency for the tone squelch function. p. 46 p. 46 Set the DTCS code for DTCS squelch operation. p. 46 1 2 3 4 5 6 7 8 9 10 11 12 13 Set the Transmit and Receive DTCS polarity. Set the duplex frequency offset. Turn the Reverse Duplex function ON or OFF Set the VFO tuning step. Select the scan pause timer option. Select the scan resume options of a pause. Set the backlight brightness. Set the Auto Dimmer brightness. p. 46 p. 46 p. 46 p. 46 p. 46 p. 46 p. 45 p. 45

(Continued on page 44) 43 11 OTHER FUNCTIONS Set mode (continued)

: [MONI]

: [SET]

Display color Display contrast Transmit permission Channel skip setting Bank setting Bank link function Wide/Narrow SET MONI SET MONI SET MONI SET MONI SET MONI SET MONI SET MONI Appears only when accessing the Set mode from the memory mode. Select the display backlight color. Adjust the LCD contrast. Turns the TX inhibit function ON or OFF. Turns the Skip function ON or OFF. p. 45 p. 45 p. 45 p. 45 Assign the desired memory and scan edge channels. p. 45 Assign the desired banks for a continuous banks scan. p. 45 Set both the transmission and reception passband. p. 45 Weather alert (For only the USA version.) MIC gain SET MONI SET MONI Turn the weather Alert function ON or OFF. Set the microphone sensitivity. p. 46 p. 46 44 Display dimmer D Set the backlight brightness to between 1 (Dark) and 4 (Bright; default). MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Auto dimmer D Set the Auto Dimmer brightness. The Auto Dimmer function automatically reduces the backlight brightness if no operation has been performed for 5 seconds. ATD OF (default) : Auto Dimmer function is turned OFF. The backlight is continuously ON, while the transceiver is turned ON.

: The backlight automatically turns OFF if no operation has been per-

formed for 5 seconds. AT OF AT D1 AT D3 : The backlight lights with the level 1 (Dark) to 3 (Bright), if no opera-

tion has been performed for 5 sec-

onds. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Display color D Select the display backlight color from Amber (default), Yellow or Green. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Amber (default) Yellow OTHER FUNCTIONS 11 Channel skip setting D Turns the Skip function ON (skip) or OFF. This item appears only when the Set mode is accessed from the memory mode. 00 MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Scans the memory channel during memory or bank scan. (default) Skips the memory channel during a memory or bank scan. Memory bank setting D Assign the desired memory channels and scan edge channels to the memory bank, for easy memory man-

agement. 10 banks, Bank-A to Bank-J, are selectable. This item appears only when the Set mode is accessed from the memory mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Not assigned (default) Assigned to the bank A Memory bank link function D The transceiver has 10 banks, A to J. Regular memory channels 0 to 199, and scan edge channels 1A to 3B, can be assigned into the desired bank for easy memory management. The link function has a continuous banks scan that scans all contents in the selected banks during the scan. This item appears only when the Set mode is accessed from the memory mode. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Bank link OFF (default) Bank link ON 1 2 3 4 5 6 7 8 9 10 11 12 13 LCD contrast D Adjust the LCD contrast. Adjustable level: 1 (the lowest contrast) to 4 (the high-

est contrast). Setting the Bank link q Rotate [DIAL] to turn ON the Memory Bank Link function. w Push [SET] or [MONI] to select the desired bank to DIGITAL PRIO AO BUSY be linked. MUTE NAR MID LOW LOCK SET ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Contrast level 2 (default) Transmit permission D Select OFF to inhibit transmitting on the channel. This function can be independently set for each memo-

ry channel, Call channel and VFO. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Transmit is permitted. (default) Transmit is inhibited. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz e Rotate [DIAL] to select ON to link the bank. r Repeat steps w and e, to set the links. Wide/Narrow setting D Set both the transmission and reception passband width to wide or narrow. This setting can be independently set for each memory channel, Call channel and VFO. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Wide (default) Narrow 45 11 OTHER FUNCTIONS Microphone sensitivity D Set the microphone sensitivity to High (HI) or Low (LO) to suit your preference. Higher value makes the microphone more sensitive to your voice.

(default: Depending on the transceiver versions) MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz High sensitivity Low sensitivity Repeater tone D Select the subaudible tone needed to access the re-

peater. A total of 50 tone frequencies (67.0254.1 Hz) are selectable. (default: 88.5 Hz) MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Tone squelch frequency D Select the CTCSS tone frequency to use for the Tone Squelch function. A total of 50 tone frequencies (67.0254.1 Hz) are se-

lectable. (default: 88.5 Hz) Frequency offset D Set the duplex frequency offset between 0 and 20 MHz. In the duplex mode, the transmit frequency shifts up or down from the receive frequency by the offset amount.

(default: Depending on the transceiver versions) MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Reverse function D Turn the Reverse Duplex function ON or OFF (default). When the Reverse Duplex function is ON, the receive and transmit frequencies are reversed. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz OFF: Normal duplex (default) ON: Reversed duplex Tuning step D Set the VFO tuning step to 5, 6.25, 10, 12.5, 15, 20, 25, 30 or 50 kHz.

(default: Depending on the transceiver versions) MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Selectable subaudible tone frequencies 67.0 69.3 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 97.4 100.0 103.5 107.2 110.9 114.8 118.8 123.0 127.3 131.8 136.5 141.3 146.2 151.4 156.7 159.8 162.2 165.5 167.9 171.3 173.8 177.3 179.9 183.5 186.2 189.9 192.8 196.6 199.5 203.5 206.5 210.7 218.1 225.7 229.1 233.6 241.8 250.3 254.1 DTCS code D Set the DTCS code (both encoder and decoder) for DTCS squelch operation. A total of 104 codes are se-

lectable. (default: 023) MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Weather alert function D Turn the Weather Alert function ON or OFF. U.S.A. versions only MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz SCT-1SCT-5 Weather alert OFF (default) Weather alert ON SCT-HO DTCS polarity D Set the Transmit and Receive DTCS polarity to NN, NR, RN or RR. (default: NN) MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz 46 D Scan pause timer D Select the scan pause timer option. When receiving a signal, the scan pauses according to the scan Pause Timer. (default: SCP-10) SCP-2SCP-20 : When receiving a signal, the scan pauses for 2 to 20 seconds

(set in 2 seconds steps).

: When a signal is received, the scan pauses until it disappears. SCP-HO MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Scan resume timer D Set the scan resume options of a pause after the re-

ceived signal disappears. (default: SCT-2) SCT-0

: The scan resumes immediately after the signal disappears.

: The scan resumes 1 to 5 sec-

onds after the signal disappears.

: The scan remains paused ac-

cording to the Pause Timer, even if the signal disappears. Rotate

[DIAL] to resume the scan. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz OTHER FUNCTIONS 11 Initial Set mode The Initial Set mode is accessed at power ON, and al-

lows you to set seldom-changed settings. In this way, you can customize the transceiver to suit your prefer-

ence and operating style. Entering the Initial Set mode D q While holding down [SET], hold down [

ond to enter the Initial Set mode.

] for 1 sec-

w Push [SET] or [MONI] to select the desired item. e Rotate [DIAL] to set the option or value. r Push [

] to exit the Initial Set mode.

[SET]

Initial Set mode items Key-touch beep

: [MONI]

: [SET]

Time-out timer MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL ANM MONI DUP LOW T-SCAN TONE DIGITAL ANM MONI DUP LOW T-SCAN TONE Turn the confirmation beeps ON (default) or OFF. p. 48 Inhibit continuous transmissions longer than the set time period. p. 48 Auto repeater (For only the USA version.) MUTE NAR MID LOW LOCK SET DIGITAL ANM MONI DUP LOW T-SCAN TONE Auto power OFF Repeater lockout MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL ANM MONI DUP LOW T-SCAN TONE DIGITAL ANM MONI DUP LOW T-SCAN TONE Turns the Auto Repeater function ON or OFF. Automatically turns the transceivers power OFF. Set the transmission lockout capability. Squelch delay Squelch type MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL ANM MONI DUP LOW T-SCAN TONE Set the squelch delay. DIGITAL Set the squelch type. ANM MONI DUP LOW T-SCAN TONE Tone burst MUTE NAR MID LOW LOCK SET DIGITAL ANM MONI DUP LOW T-SCAN TONE DTMF speed Display type MUTE NAR MID LOW LOCK SET MUTE NAR MID LOW LOCK SET DIGITAL ANM MONI DUP LOW T-SCAN TONE DIGITAL ANM MONI DUP LOW T-SCAN TONE Voltage display MUTE NAR MID LOW LOCK SET DIGITAL ANM MONI DUP LOW T-SCAN TONE Turn the Tone Burst function ON or OFF. Set the DTMF sending rate. Set the display type for memory mode operation. Turn the Voltage display function ON or OFF. p. 48 p. 48 p. 48 p. 48 p. 48 p. 49 p. 49 p. 49 p. 49 00 1 2 3 4 5 6 7 8 9 10 11 12 13 47 Repeater lockout D Set the transmission lockout (temporary transmission inhibit) capability. OF : No lockout is activated. (default) RP : The repeater lockout is turned ON. BU : The busy lockout is turned ON. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Busy lock-out setting Repeater lock-out setting Squelch delay D Set the squelch delay to short or long. The delay pre-

vents the squelch from repeatedly opening and closing, while receiving the same signal. S L

: Short squelch delay. (default)

: Long squelch delay. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Short squelch delay setting Long squelch delay setting Squelch type D Set the squelch type to OFF (Noise squelch), S-meter Squelch or Squelch Attenuator. OF : Noise squelch (default) SS : S-meter squelch The S-meter squelch allows you to set a mini-

mum signal level needed to open the squelch. Rotate [SQL] to adjust the S-meter squelch lev-

el. The S-meter is automatically activated when

[SQL] is rotated further than the 12 o'clock posi-

tion. AT : Squelch Attenuator The attenuator is automatically activated when

[SQL] is rotated further than the 12 o'clock posi-

tion. Approximately 20 dB of attenuation is ob-

tained at the maximum setting. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Noise squelch (default) S-meter squelch 11 OTHER FUNCTIONS Key-touch beep D Turn the con rmation beeps ON (default) or OFF. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Time-out timer D To prevent accidental prolonged transmission, the transceiver has a time-out timer. The function inhibits continuous transmissions longer than the set time pe-

riod (130 minutes). TOT-OF TOT-130

: Turns OFF the function. (default)

: The transmission is cut OFF after the set time period ends. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Auto repeater U.S.A. version only D The Auto Repeater function automatically turns the duplex setting and tone encoder ON or OFF when the operating frequency falls within or outside of the general repeater output frequency range (145.200 145.495 MHz, 146.610146.995 MHz and 147.000 147.395 MHz). The offset and repeater tone frequencies are not changed by the Auto Repeater function; reset these frequencies, if necessary. OF : The Auto Repeater function is OFF. R1 : Activates for duplex only. (default) R2 : Activates for duplex and tone. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Auto power OFF D The transceiver can be automatically turned OFF, when no key operation is performed for the speci ed time pe-

riod. 30 min., 1 hour, 2 hours and OFF (default) are se-

lectable. The time period is retained, even if the transceiver is turned OFF by the auto power OFF function. To cancel the function, select OF (OFF). MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET AO DIGITAL PRIO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz 48 OTHER FUNCTIONS 11 Tone burst D Turn the Tone Burst function ON or OFF. OF : When you transmit a signal that superimposes the CTCSS tone or subaudible tone, the squelch tail noise may be audible on the RX side. ON : When you transmit a signal which superimposes the CTCSS tone or subaudible tone, the squelch tail noise is suppressed on the RX side. Tone burst OFF (default) DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK SET ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz DTMF speed D Set the rate at which DTMF memories send individual DTMF characters to accommodate your operating needs.

: 100 milliseconds interval; 5.0 cps speed (default) 1 2

: 200 milliseconds interval; 2.5 cps speed

: 300 milliseconds interval; 1.6 cps speed 3 5

: 500 milliseconds interval; 1.0 cps speed MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Display type D Set the display type for memory mode operation. FR : Displays the programmed frequency. (default) CH : Displays the memory channel number.*

NM : Displays the channel name (if programmed)

*Only programmed memory channels can be selected. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Frequency Memory channel number Voltage display D Turn the Voltage display function ON or OFF. OF : OFF. ON : The supplied voltage is displayed, when turning ON the power. (default) MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz 00 1 2 3 4 5 6 7 8 9 10 11 12 13 49

(Only USA versions) MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY Weather channel number ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz When the weather alert is detected:

MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz Alternately displays above indications. 11 OTHER FUNCTIONS Weather channel operation Weather channel selection D q Push [M/CALL] one or more times to select the weather channel group. w Rotate [DIAL] to select the desired weather chan-

nel. e Push [M/CALL] to select the memory mode, or push

[V/MH z] to select the VFO mode. Weather Alert function D NOAA broadcast stations transmit weather alert tones before important weather announcements. When the Weather Alert function is turned ON, the transceiver checks the selected weather channel every 5 seconds. for an announcement. When the alert signal is detect-

ed, the AL.T and the WX channel are displayed al-

ternately and a beep tone sounds until the transceiver is operated. The selected (used) weather channel is checked periodically during standby or while scanning. q Select the desired weather channel. w Push [SET] to enter the Set mode. e Push [SET] or [MONI] to select the weather alert item, and then rotate [DIAL] to select ON."

r Push any key other than [SET] or [MONI] to save the selection and exit the Set mode. t Set the desired stand-by mode. Select the VFO, memory channel or Call channel. Scan or priority watch operation can be also se-

lected. y When the alert is detected, a beep sounds and the following will be displayed. NOTE: While receiving a signal on a frequency other than the weather channel, the receiving audio will be momentarily interrupted approximately every 5 sec-

onds, when the alert function is turned ON. This is caused by the WX alert function. To cancel these in-

terruptions, turn OFF the Wweather Alert function in the Set mode. 50 and [F-2]

Microphone keys

[F-1]

memorize the transceiver settings. The [UP] and [DOWN] keys on the standard or optional mi-

crophone (other than the HM-133V) can be assigned func-

tions like the function keys on the transceivers front panel. on the supplied HM-133V

[F-1] and [F-2] keys on HM-133V D The following functions can be assigned to the micro-

phone's [F-1]

and [F-2]

keys. Operating conditions:

Operating frequency Repeater settings

(offset direction and offset, tone ON/OFF and frequency) Tone/DTCS squelch

(ON/OFF, frequency/code and polarity) Transmit output power setting Programming the function Set the desired function, and then hold down [F-1]

or [F-2]

3 beeps sound. for 1 second. Re-calling the function Push [F-1]

or [F-2]

. Set mode items:

Setting the Set mode items Setting the Initial Set mode items (except Display Type) Programming the function q Set the desired item in the Set mode, and then exit the mode. w Push [FUNC]

, and then hold down [F-1]

for 1 second. or [F-2]

3 beeps sound. Re-calling the function Push [FUNC]

, then [F-1]

or [F-2]

[UP] and [DN] keys on a microphones other than the HM-133V D When turning ON the transceiver's power, the following functions are pre-assigned to [UP] or [DN] on micro-

phones other than HM-133V.

[UP] : Channel up; hold down for 1 second to start the scan, push again to stop it.

[DN] : Channel down; hold down for 1 second to start the scan, push again to stop it. Assigning a function q Turn OFF the power. w While holding down the desired key on the trans-

ceiver and either [UP] or [DN] keys on the micro-

phone, turn ON the power. The function is assigned to the key. Clearing an assignment q Turn OFF the power. w While holding down the desired [UP] or [DN] key on the microphone, turn ON the power. OTHER FUNCTIONS 11 00 1 2 3 4 5 6 7 8 9 10 11 12 13 51 11 OTHER FUNCTIONS Partial reset If you want to reset the VFO frequency, VFO settings and Set mode items to their default values, without clearing the memory contents, you can do a partial reset of the transceiver's CPU. While holding down [V/MHz], hold down [

] for 1 sec-

ond to turn ON the power. The CPU is partially reset. All Reset The function display may, at rare times, display errone-

ous information (for example when rst applying pow-

er). This may be externally caused by static electricity or other factors. In such case, rst turn OFF the power, wait a few sec-

onds, then turn ON the power again. If the problem persists, perform the following proce-

dure. IMPORTANT!:

All Rest CLEARS all memory contents and resets all values in the CPU to default. A Partial Reset can also be done that will not clear memory content, but may not solve the problem.

[SCAN] (V/MHz) q Turn OFF the power, if the transceiver is ON. w While holding down [SET] and [S.MW], hold down

] for 1 second to turn ON the power.

The transceiver is totally reset.

[LOCK] (SET)

[MW] (S.MW) 52 Data cloning Cloning allows you to quickly and easily transfer the programmed contents from one transceiver to another, or data from a personal computer to a transceiver, us-

ing the optional CS-2300H CLONING SOFTWARE. D Cloning between two transceivers q Connect the master and sub-transceivers using the OPC-474 cloning cable through the speaker jack. The master transceiver is used to send data to the sub-transceiver. w Enter the cloning mode as following. For the master transceiver:

While holding down [M/CALL] (PRIO), hold down [

for 1 second to turn ON the power.

] 1 second to turn ON the power. CLONE appears and the transceivers enter the For the sub-transceiver:

Hold down [

cloning standby mode. e Push [S.MW] on the master transceiver. CL OUT appears on the master transceivers display and the S/RF meter shows that data is being transferred to the sub-transceiver. CL IN appears on the sub-transceivers display and the S/RF meter shows that data is being received from the master transceiver. r When the cloning is nished, turn OFF both trans-

ceiver's power, and then turn ON the power again to exit the cloning mode. OTHER FUNCTIONS 11 While holding down [PRIO] (M/CALL) for 1 second, turn ON the power. Push [S.MW] to start cloning

(master transceiver). MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz During cloning mode MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz While cloning D Cloning using a PC Data can be transferred to and from a PC, using the optional CS-2300H CLONING SOFTWARE and OPC-478

(RS-232C type) or OPC-478UC (USB type) CLON-

ING CABLE. Consult the CS-2300H CLONING SOFTWARE HELP le for details. PC to the RS-232C port OPC-478 or OPC-478UC to the USB port D Cloning error NOTE: DO NOT push any key on the sub-transceiver while cloning. This will cause an error. When the display to the right appears, a cloning error has occurred. In this case, both transceivers automatically return to the clone standby mode. Please follow the cloning pro-

cedures again. MUTE NAR MID LOW LOCK SET DIGITAL PRIO AO BUSY ANM MONI DUP LOW T-SCAN TONE PRIO M/CALL SCAN V/MHz 00 1 2 3 4 5 6 7 8 9 10 11 12 13 53 M TRANSMITTER Modulation system Output power (approximately) :

High:

Mid:

Mid-Low:

Low:

: Variable reactance frequency mod. USA, Export Taiwan Korea 65 W 25 W 10 W 5 W 24 W 50 W 10 W 5 W 25 W 10 W 5 W Max. frequency deviation Spurious emissions Microphone connector

: 5.0 kHz (Wide)/2.5 kHz (Narrow)

: Less than 60 dBc

: 8-pin modular (600 :) M RECEIVER Receive system Intermediate frequencies Sensitivity (at 12 dB SINAD) Squelch sensitivity Selectivity

[Wide]

[Narrow]

: Double-conversion superheterodyne

: 1st: 46.35 MHz, 2nd: 450 kHz

: Less than 0.18 V

: Less than 0.13 V (threshold)

More than 6 kHz/6 dB Less than 14 kHz/60 dB More than 3 kHz/6 dB Less than 9 kHz/55 dB Spurious and image rejection : More than 60 dB AF output power (at 13.8 V DC) : More than 3.5 W (4.5 W typical) External speaker connector

(at 10% distortion with a 4 : load)

: 3-conductor 3.5 (d) mm (1/8 inch)/4 :

12 SPECIFICATIONS

M GENERAL Frequency coverage USA Export Taiwan, Korea Type of emission Number of memory channels : 207 (incl. 6 scan edges and 1 Call) Scan types Tx: 144148/Rx: 136174*

Tx: 136174*/Rx: 136174*

Tx/Rx: 144146

*Guaranteed: 144148 MHz range only.

: FM

(unit: MHz)

: Full, Program, Priority, Memory channel, Bank, Skip, Tone scans

: 5, 6.25, 10, 12.5, 15, 20, 25, 30, 50 kHz Frequency resolution Operating temperature range : 10C to +60C; +14F to +140F Frequency stability Power supply requirement Current drain (at 13.8 V DC: approximately):

: 3 ppm (10C to +60C)

: 13.8 V DC 15%

Transmit 11 A at 65 W

( less than 9 A at 24 W for the Taiwan version) standby 0.4 A max. audio 1.5 A

: SO-239 (50 :) Receive Antenna connector Dimensions (proj. not included) : 140.0(W)40.0(H)118.0(D) mm;

Weight (approximately) 5.5(W)1.6(H)4.6(D) in

: 1.1 kg; 2.4 lb All stated speci cations are subject to change without notice or obligation. 54 MAINTENANCE 13 Troubleshooting If your transceiver seems to be malfunctioning, please check the followings before sending it to the service center. 00 PROBLEM No power comes on. POSSIBLE CAUSE SOLUTION Power connector has a poor contact. Polarity of the power connection is re-

Check the connector pins. Re-connect the power cable observing the REF. p. iv versed. Blown fuse. proper polarity. Replace the fuse if blown. Check the cause, repair it, then replace the No sound comes from the speaker. Sensitivity is low and only strong signals are audible. Volume is too low. The audio mute function is activated. Squelch is set too tight. A selective call or Squelch function is activated such as pocket beep or tone squelch. Antenna feedline or the antenna con-

nector solder has a poor contact or is shorted. Squelch attenuator function is activated. fuse following the instruction below. Rotate [VOL] clockwise. Push any switch or key to deactivate it. Set the squelch level to the threshold. Turn OFF the those functions. p. 8 p. 9 p. 8 pp. 39, 41 Check, and if necessary, replace the feedline p. v or re-solder the antenna connector. Set [SQL] to between the 10 and 12 oclock position. Turn OFF the S-meter squelch or squelch at-

tenuator. Set the appropriate tone frequency or code, and then turn ON the tone or DTCS squelch. p. 8 p. 9 p. 41 p. 12 p. 15 p. 13 p. 7 p. 35 p. 7 p. 35 No direct contact possible with other stations. Repeater cannot be ac-

cessed. The other station is using tone squelch. The transceiver is set to duplex. Wrong frequency offset is programmed. Wrong subaudible tone frequency is pro-

Select the simplex mode. Correct the frequency offset. Correct the subaudible tone frequency. grammed. Frequency cannot be set. The frequency lock function is activated. Priority watch is paused on the watching Turn the function OFF. Cancel the watch. frequency. Frequency cannot be set using the microphone. The frequency lock function is activated. Priority watch is paused on the watching Turn the function OFF. Cancel the watch. frequency. Some memory channels cannot be selected using the microphone keypad. Scan does not start. The input channel number has not yet Rotate [DIAL] to check whether the channel been programmed. has been programmed or not. The squelch is open. Only one memory channel is programmed or other channels are set as skip channels. Set the squelch to the threshold point. Program other memory channels or cancel the memory skip function in the desired chan-

nels. p. 8 pp. 17, 32 Transmission is automatically cut off. Transmission continues even when the PTT is released. The function display shows erroneous information. Priority watch is activated. Time-out timer is activated. Cancel the watch. Turn OFF the timer. One-touch PTT function is activated. Turn OFF the function. The CPU is malfunctioning. Reset the CPU. p. 35 p. 48 p. 11 p. 52 Fuse replacement If the fuse is blown or the transceiver stops functioning, nd the source of the problem if possible, repair the problem and then replace the damaged fuse with a new rated one (FGB 20 A), as shown at right. 20 A fuse 1 2 3 4 5 6 7 8 9 10 11 12 13 55 A-6966-1EX Printed in Japan 2011 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan