all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 2.79 MiB | / January 09 2014 | |||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | Attestation Statements | |||||||
1 | External Photos | / January 09 2014 | ||||||
1 | Internal Photos | / January 09 2014 | ||||||
1 | ID Label/Location Info | |||||||
1 | Attestation Statements | |||||||
1 | Attestation Statements | |||||||
1 | Attestation Statements | |||||||
1 | Attestation Statements | |||||||
1 | RF Exposure Info | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | User Manual | Users Manual | 2.79 MiB | / January 09 2014 |
OPERATING INSTRUCTIONS INTRODUCTION VHF DIGITAL TRANSCEIVERS iF5360D UHF DIGITAL TRANSCEIVERS iF6360D 1 PANEL DESCRIPTION 2 BASIC OPERATION 3 ADVANCED OPERATION 4 SCAN OPERATION 5 MENU SCREEN 6 NXDN OPERATION <COMMON>
7 NXDN OPERATION <TRUNKING MODE>
8 NXDN OPERATION <CONVENTIONAL MODE>
INTRODUCTION FOREWORD Thank you for purchasing this Icom transceiver. The IDAS NXDN system operation is built into your IC-F5360D vhf digital transceivers and IC-F6360D uhf digital transceivers. IMPORTANT FIRST, CAREFULLY READ INSTRUCTIONS q PRECAUTIONS and w INSTRUCTIONS that are provided with the transceiver. SAVE THIS OPERATING INSTRUCTIONS This operating instructions contain additional important operating instructions for the IC-F5360D vhf digital transceivers and IC-F6360D uhf digital transceiv-
ers. NOTE The display contents, and the hold down time period of some keys, may vary from the description in this manu-
al, depending on the transceivers presetting. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/
or other countries. IDAS is trademark of Icom Incorporated (Japan). NXDN is a trademark of Icom Incorporated and JVC KEN-
WOOD Corporation. All other products or brands are registered trademarks or trademarks of their respective holders. i Section 1 PANEL DESCRIPTION D Microphone Front, top and side panels ......................................................1-2
..............................................................................1-2 Function display ......................................................................1-3 Programmable function keys .................................................1-4 1-1 1 PANEL DESCRIPTION Front, top and side panels q LED INDICATOR w FUNCTION DISPLAY e DEALER PROGRAMMABLE KEYS
[UP], [DOWN]
u AF VOLUME CONTROL KNOB [VOL]
y MICROPHONE CONNECTOR SPEAKER t DEALER-PROGRAMMABLE KEYS
[R], [P0], [P1], [P2], [P3]
r POWER KEY [
]
q LED INDICATOR Lights red while transmitting. Lights green while receiving a signal, or when the squelch is open. w FUNCTION DISPLAY (p. 1-3) Displays a variety of information. e DEALER-PROGRAMMABLE KEYS
[UP] and [DOWN]
(p. 1-5) Desired functions can be preset. r POWER KEY [
Push and hold for 1 second to turn the power ON
]
and OFF. t DEALER-PROGRAMMABLE KEYS
[R], [P0], [P1], [P2], [P3]
Microphone D The supplied or optional microphone has a PTT switch and a hanger hook. The following functions are available when the micro-
phone is on or off hook (depending on the presetting):
- Pauses scan when it is off-hook.
- Switches to the Inaudible mode (mute mode) when it is on-hook.
- Switches to the Audible mode (unmute mode) when it is off-hook.
(p. 1-5) Desired functions can be preset. y MICROPHONE CONNECTOR Connect the supplied or optional microphone. NEVER connect non-specified microphones. The pin assignments may be different and the trans-
ceiver may be damaged. u AF VOLUME CONTROL KNOB [VOL]
Rotate to adjust the audio output level. 1-2 1 PANEL DESCRIPTION Function display q w e r t y u i o !0 IC-F5360D
!3 !4
!5 !6 !7 !8
!1
!2 o HORN ALERT ICON Displayed when the Horn Alert function is ON.
!0 PUBLIC ADDRESS ICON Displayed when the Public Address function is ON.
!1 ALPHANUMERIC READOUT Displays the operating channel number, channel name, menu contents, DTMF code, and so on. The display mode automatically switches between one line and two lines.
!2 KEY ICONS Display the assigned function of the [P0], [P1], [P2]
and [P3] dealer assignable keys. Displayed when the scan target zone is selected.
!3 SCAN TARGET ZONE ICON
!4 PA SPEAKER ICON Displayed when the External speaker function is ON. When the External speaker function is ON, the PA speaker that is connected to the D-Sub 15-pin will activate. Displayed when the AUX B port is activate. Displayed when the AUX A port is activate.
!5 AUX A ICON
!6 AUX B ICON
!7 SCAN TARGET CHANNEL ICON
!8 OPERATOR SELECTABLE TONE ICON Displayed when the scan target channel is selected. Displayed when the OST (Operator Selectable Tone) function is ON. Displays the relative receive signal strength. q SIGNAL STRENGTH INDICATOR w LOW OUTPUT POWER ICON Displayed when low output power is selected. e AUDIBLE ICON 5219 200%
150%
Displayed when the channel is in the audible (un-
mute) mode. Displayed when the Voice Scrambler function is ON. r SCRAMBLER ICON t SCAN ICON y MESSAGE ICON Displayed while scanning. Displayed when a received message (Short Data Message or Status Message) is stored in the memory stack. Blinks when an unread message is in the memory stack. u BELL ICON Blinks when a matched signal is received, depend-
ing on the presetting. i GPS ICON Displayed when position data is received. 1-3 1 PANEL DESCRIPTION Programmable function keys The programmable key functions can be assigned to the following keys:
[R], [P0], [P1], [P2], [P3], [UP], [DOWN] and to the key-
pad keys of the optional DTMF microphone.
[UP], [DOWN]
[R], [P0], [P1], [P2], [P3]
1-4 1 PANEL DESCRIPTION Programmable function keys (Continued) For [R], [P0], [P1], [P2], [P3], [UP] and [DOWN]
The key names that are in quotation marks in the fol-
lowing explanations are displayed on the Function Dis-
play, and indicate the assigned function of [P0], [P1],
[P2] and [P3]. None No function CH/GID Down CH D Selects the next or previous channel or GID number. CH/GID Recall CHRC In the Analog mode or NXDN Conventional system Selects the last used channel during a scan. Autodial ADAL (p. 3-2) Opens the DTMF Autodial code selection screen. In the NXDN Trunking system Selects the last called GID during a scan. Autodial Programming ADPG (p. 3-3) Enters the DTMF code programming mode. CH/GID Up CH U Selects the next or previous channel or GID number. AUX A AUXA Turns the AUX A port ON or OFF. AUX B AUXB Turns the AUX B port ON or OFF. Broadcast BCST Toggles between Broadcast Call and Conference Call. This key can also be used to make a Broadcast Group Call. Call 1 CAL1 Sends the NXDN Status, NXDN Individual or the DTMF code that is set to Call 1. Call 2 CAL2 Sends the NXDN Status, NXDN Individual or the DTMF code that is set to Call 2. Call 3 CAL3 Sends the NXDN Status, NXDN Individual or the DTMF code that is set to Call 3. Call 4 CAL4 Sends the NXDN Status, NXDN Individual or the DTMF code that is set to Call 4. Call 5 CAL5 Sends the NXDN Status, NXDN Individual or the DTMF code that is set to Call 5. Call 6 CAL6 Sends the NXDN Status, NXDN Individual or the DTMF code that is set to Call 6. Channel Entry CHEN (p. 2-4) Enters the Channel Entry mode. CW Message CWMS Sends a preset CW Message on a very narrow chan-
nel. You can use this function when a CW message is pre-
set. Direct CH/GID 1 DR 1 (pp. 2-4, 7-3) Selects the channel or GID that is set to Direct CH/
GID 1. Direct CH/GID 2 DR 2 (pp. 2-4, 7-3) Selects the channel or GID that is set to the Direct CH/
GID 2. Direct CH/GID 3 DR 3 (pp. 2-4, 7-3) Selects the channel or GID that is set to Direct CH/
GID 3. Direct CH/GID 4 DR 4 (pp. 2-4, 7-3) Selects the channel or GID that is set to Direct CH/
GID 4. Direct CH/GID 5 DR 5 (pp. 2-4, 7-3) Selects the channel or GID that is set to Direct CH/
GID 5. Direct CH/GID 1 Select This function is for the hold down operation of [Direct CH/GID 1]. Sets the selected channel or GID to Direct CH/GID 1. 1-5 1 PANEL DESCRIPTION Programmable function keys For [R], [P0], [P1], [P2], [P3], [UP] and [DOWN] (Continued) Direct CH/GID 2 Select This function is for the hold down operation of [Direct CH/GID 2]. Sets the selected channel or GID to Direct CH/GID 2. Function FUNC Activates a secondary function that is assigned to a key. This function cannot be assigned as a secondary func-
tion. Direct CH/GID 3 Select This function is for the hold down operation of [Direct CH/GID 3]. Sets the selected channel or GID to Direct CH/GID 3. Direct CH/GID 4 Select This function is for the hold down operation of [Direct CH/GID 4]. Sets the selected channel or GID to Direct CH/GID 4. Direct CH/GID 5 Select This function is for the hold down operation of [Direct CH/GID 5]. Sets the selected channel or GID to Direct CH/GID 5. Display Format DISP In the Analog mode or NXDN Conventional system Toggles the display format between the channel name and the zone and channel number. In the NXDN Trunking system Toggles the display format between the GID name and the GID number. Emergency (p. 3-5) This function can be assigned only for [R]. Enters the Emergency mode. External Speaker EXSP Turns the External speaker function ON or OFF. When the External speaker function is ON, the PA speaker that is connected to the D-Sub 15-pin will be activated. Fixed Volume FIXV Toggles the tone level between High and Low, or turns OFF the tone. Forced Search FORS Displays the site number of the current site for 2 sec-
onds. Forced Search Function This function is for the hold down operation of [Forced Search]. Activates a Control Channel Hunt. 1-6 GPS Position Display GPSP Enters the GPS Position Display mode. In the GPS Position Display mode, you can check your latitude and longitude position. Group ID/Channel Entry GIDE (pp. 2-4, 7-3) In the Analog mode or NXDN Conventional system Enters the Channel Entry mode. In the NXDN Trunking system Enters the GID Entry mode. Group (NXDN) GRP (pp. 7-4, 8-3) In the NXDN Conventional system or the NXDN Trunking system Enters the Group Call mode. In the NXDN Conventional system, this function is used for Group Call by recalling GID list. In the NXDN Trunking system, the GID List is displayed, but the transceiver cannot make a call. Group + SDM (NXDN) GSMS In the NXDN Conventional system or the NXDN Trunking system Enters the Group Call mode. If you push [P1](ENT) while in the Group Call mode, the transceiver enters the Short Data Message Entry mode. See page 7-4 or 8-3 for details. Group + Status (NXDN) GSTA In the NXDN Conventional system or the NXDN Trunking system Enters the Group Call mode. If you push [P1](ENT) while in the Group Call mode, the transceiver enters the Status Message Entry mode. See page 7-4 or 8-3 for details. High Transmit Power HIPW In the NXDN Trunking system Toggles the transmit power level between High and Auto, if Auto is set as the default. Toggles the transmit power level between High and Low, if Low is set as the default. 1 PANEL DESCRIPTION Programmable function keys For [R], [P0], [P1], [P2], [P3], [UP] and [DOWN] (Continued) Home CH/GID HOME (pp. 2-4, 7-3) In the Analog mode or Low Transmit Power LOPW In the Analog mode or NXDN Conventional system Selects the Home Channel. In the NXDN Trunking system Selects the Home GID. Home CH/GID Select (pp. 2-4, 7-3) This function is for the hold down operation of [Home CH/GID]. In the Analog mode or NXDN Conventional system Sets the selected channel as the Home Channel. NXDN Conventional system Toggles the transmit power between High and Low, if High is set as the default. In the NXDN Trunking system Toggles the transmit power level between Low and Auto, if Auto is set as the default. Toggles the transmit power level between High and Low, if High is set as the default. Maintenance MANT Enters the Maintenance Display mode. In the NXDN Trunking system Sets the selected GID as the Home GID. Menu MENU (p. 5-2) Displays the Menu screen. Horn Alert HORN Turns the Horn Alert function ON or OFF. When this function is ON, the horn alert port will be ac-
tivated for a preset time period after receiving a call. Individual (NXDN) INDV (pp. 7-5, 7-6, 8-4) In the NXDN Conventional system or the NXDN Trunking system Enters the Individual Call mode. Individual + SDM (NXDN) ISMS In the NXDN Conventional system or the NXDN Trunking system Enters the Individual Call mode. If you push [P1](ENT) while in the Individual Call mode, the transceiver enters the Short Data Message Entry mode. See page 7-5 or 8-4 for details. Individual + Status (NXDN) ISTA In the NXDN Conventional system or the NXDN Trunking system Enters the Individual Call mode. If you push [P1](ENT) while in the Individual Call mode, the transceiver enters the Status Message Entry mode. See page 7-5 or 8-4 for details. LCD Brightness BRIT Selects the brightness of the function display and keys backlight. Select High, Low or OFF to meet your needs. The function display and keys can be backlit for better visibility under low light conditions. Lone Worker LONE (p. 3-5) Turns the Lone Worker function ON or OFF. Monitor MONI In the Analog mode Turns the Monitor ON or OFF. When the Monitor is ON, the transceiver releases the CTCSS or DTCS mute. In the NXDN Conventional system Turns the Monitor ON or OFF. When the Monitor is ON, the transceiver releases the RAN code mute. Monitor Momentary MONI In the Analog mode While holding down, the transceiver releases the CTC-
SS mute. In the NXDN Conventional system While holding down, the transceiver releases the RAN code mute. Operator Selectable Tone OST Turns the OST (Operator Selectable Tone) mode ON or OFF. When the OST mode is ON, the selected tone in the OST list is enabled. OST List This function is for the hold down operation of [Opera-
tor Selectable Tone]. Displays the OST (Operator Selectable Tone) list. Priority-channel Select PRIO Enters the Priority channel Select mode for a Priority scan. 1-7 1 PANEL DESCRIPTION Programmable function keys For [R], [P0], [P1], [P2], [P3], [UP] and [DOWN] (Continued) Public Address PUBA Turns the Public Address function ON or OFF. When this function is ON, you can make announce-
ment through a PA speaker. Transmitting is disabled while in the PA mode. Scan SCAN Starts or stops a scan. Scan Delete/Add SCNE Sets or cancels the selected channel or GID as a scan target. Scrambler/Encryption SCRM In the Analog mode Turns the Scrambler function ON or OFF. In the NXDN Conventional system or the NXDN Trunking system Turns the Encryption function ON or OFF. Scrambler/Encryption Code This function is for the hold down operation of [Scram-
bler/Encryption]. In the Analog mode Enters the Scrambler Code mode. In the NXDN Conventional system or the NXDN Trunking system Enters the Encryption Code mode. SDM (NXDN) SMSG In the NXDN Conventional system or the NXDN Trunking system Directly enters the Short Message mode. Push [PTT] to send a Short Message to a Base ID. Send the GPS data GPSD In the NXDN Conventional system or the NXDN Trunking system Sends the position data that is received from the GPS receiver to a Base station. Site Down SIDN In the NXDN Trunking system Selects the previous site number. If the site name is not entered, [Site Down] does not function. Site Lock SILK In the NXDN Trunking system Turns the Site Lock function ON or OFF. Site Select This function is for the hold down operation of [Site Lock]. In the NXDN Trunking system Enters the Site Select mode. If the site name is not entered, [Site Select] does not function. Site Up SITU In the NXDN Trunking system Selects the next site number. If the site name is not entered, [Site Up] does not func-
tion. Squelch Level SQLL In the Analog mode Enters the Squelch Level Adjustment mode. Squelch Off SQLO In the Analog mode or NXDN Conventional system Opens the squelch, and releases the mute. Squelch Off Momentary SQLM In the Analog mode or NXDN Conventional system While holding down, opens the squelch, and releases the mute. Stack STAK (p. 6-3) Enters the Memory Stack mode. Status (NXDN) STAT Enters the Status Message mode. Push [PTT] to send a Status to a Base ID. Talk Around TLKA Turns the Talk around function ON or OFF. The Talk around function equalizes the transmit frequency to the receive frequency for transceiver-to-transceiver com-
munication. Transceiver Password PSWD (p. 2-2) Enters the password entry mode. The transceiver cannot be used until you enter a cor-
rect password. Zone Delete/Add ZODE Sets or cancels the selected zone as a scan target. Zone Down ZNDN Selects the previous zone number. Zone Up ZNUP Selects the next zone number. 1-8 Individual + Status (NXDN) In the NXDN Conventional system In the NXDN Trunking system Enters the Individual Call mode, and selects the unit ID to transmit an Individual Call to. If you push [P1](ENT) while in the Individual Call mode, the transceiver enters the Status Message mode. Individual + SDM (NXDN) In the NXDN Conventional system In the NXDN Trunking system Enters the Individual Call mode, and selects the unit ID to transmit an Individual Call to. If you push [P1](ENT) while in the Individual Call mode, the transceiver enters the Short Data Message mode. Group (NXDN) In the NXDN Conventional system Enters the Group Call mode, and selects the GID to send a Group Call to. In the NXDN Trunking system Displays the GID List, but the transceiver cannot make a call. Group + Status (NXDN) In the NXDN Conventional system In the NXDN Trunking system Enters the Group Call mode, and selects the GID to transmit a Group Call to. If you push [P1](ENT) while in the Group Call mode, the transceiver enters the Status Message mode. Group + SDM (NXDN) In the NXDN Conventional system In the NXDN Trunking system Enters the Group Call mode, and selects the GID to transmit a Group Call to. If you push [P1](ENT) while in the Group Call mode, the transceiver enters the Short Data Message mode. 1 PANEL DESCRIPTION Programmable function keys (Continued) For Keypad Operation (Microphone) Channel Entry (p. 2-4) Enters the channel number. Group ID/Channel Entry (pp. 2-4, 7-3) In the Analog mode In the NXDN Conventional system Enters the channel number. In the NXDN Trunking system Enters the GID. OST (Operator Selectable Tone) Hold down [1] to [9] to select a tone that is preset in the OST list. Hold down [0] to turn OFF the OST tone. Hold down [
When the OST mode is OFF, the selected channels pre-
M] to turn OFF the OST mode. set tone is used. Hold down [#], and then push the [0] to [9] digit keys to enter the OST List number 1 to 40 to select a pre-
set tone. Autodial Selects the DTMF Code that is preset in the Autodial List. After selecting, push [PTT] to send. Keypad Auto PTT Transmits DTMF tones. This function is enabled only when Manual Dialing is enabled. Status (NXDN) In the NXDN Conventional system In the NXDN Trunking system Enters the Status Message mode, and selects the Sta-
tus number. SDM (NXDN) In the NXDN Conventional system In the NXDN Trunking system Enter an SDM message. Individual (NXDN) In the NXDN Conventional system In the NXDN Trunking system Enters the Individual Call mode, and selects the unit ID to send an Individual Call to. 1-9 Section 2 BASIC OPERATION D D D Selecting a zone Adjusting the audio level Inputting the password Turning power ON ....................................................................2-2
..........................................................2-2
............................................................2-2 Selecting a zone ......................................................................2-3
......................................................................2-3 Selecting a channel .................................................................2-4
.................................................................2-4
......................................................2-4
......................................................2-4 Receiving ..................................................................................2-5
..........................................................2-5 Transmitting .............................................................................2-6
...................................................................2-6 Selecting a channel Selecting a Home channel Directly entering a channel Setting the squelch level Transmitting notes D D D D D 2-1 2 BASIC OPERATION Turning power ON Hold down [
] for 1 second to turn ON the power. D Adjusting the audio level When receiving a call, rotate [VOL] to adjust the au-
dio output volume level. Inputting the password D If the transceiver is preset for a start up password, en-
ter the digit codes. q w e While in the Password Entry mode, PASSWORD is displayed. Push [UP] or [DOWN] to enter a digit code, and then push [P1] to set. Goes to the next digit entry position. Repeat step then push [P1]. w until you enter the password, and When using the DTMF microphone:
Push the [0] to [9] digit keys on the microphone to enter the password, and then push [#]. NOTE: If PASSWORD does not disappear after pushing [P1], the password code you entered may be incorrect. In this case, enter the correct pass-
word. For your reference:
When [Transceiver Password] is assigned to any key, or the Transceiver Password item is preset in the Menu screen and [Menu] is assigned to any key, the start up password does not appear, even if the Trans-
ceiver Password is programmed. In this case, push [Transceiver Password], or select Transceiver Password in the Menu screen to enter the Password Entry mode, then enter the password as described above. 2-2
[VOL]
[
]
[P1]
[UP] [DOWN]
PASSWORD 12345 Channel 1 2 BASIC OPERATION Selecting a zone D To select a desired zone (Conventional group or NXDN Trunking system). Selecting a zone Push [Zone Up] or [Zone Down]. For your reference: What is zone?
Certain channels are grouped together and assigned to a zone according to their intended use. For example, Staff A and Staff B are assigned to a Business zone, and John and Cindy are assigned to a Private zone. NOTE:
When you select the Conventional group zone, see the page 2-4 for details of the channel selection. When you select the NXDN Trunking system zone, see page 7-3 for details of the GID (Group ID) selec-
tion. 2-3 2 BASIC OPERATION Selecting a channel Selecting a channel D To select a desired operating channel:
Push [CH/GID Up] or [CH/GID Down]. Push one of the direct channel select keys, [Direct CH/GID 1] to [Direct CH/GID 5]. You can change the channel by pushing [Direct CH/GID 1] to [Direct CH/GID 5], as described below. Changing the Direct channel setting:
q w Select a desired channel. Hold down one of the [Direct CH/GID 1] to [Direct CH/GID 5] keys for 3 seconds to set the selected channel to the Direct channel 1 to 5. Selecting a Home channel D The Home channel is an often-used Memory channel you can preset in the transceiver. Push [Home CH/GID]. To change the Home channel, see the description below. Changing the Home channel setting:
q w Select a desired channel. Hold down [Home CH/GID Select] for 3 seconds to set the selected channel as the Home channel. Directly entering a channel D You can select a channel by pushing [UP] or [DOWN] or the [0] to [9] digit keys on the microphone, after pushing
[Channel Entry]. Or, when the Channel Entry function is assigned to the keypad, you can select a channel by pushing [0] to [9]
digit keys on the microphone. q Push [Channel Entry] to enter the Channel Entry mode. CH ENTER MOD CH No. _ _ w Push [UP] or [DOWN] to select the channel number, and then push [P1](SEL). Push [P0](BACK) to cancel the entry, and return to the screen that you selected before entering the Channel En-
try mode. You can use the digit keys on the microphone. Channel 1 When using the DTMF microphone:
q Push the [0] to [9] digit keys to enter the Channel Entry mode. CH ENTER MOD CH No. _ 1 w Enter the channel number, and then push [#]. Push [M] to delete the entered number. Push [M] again to cancel the entry, and return to the screen that you selected before entering the Channel Entry mode. Channel 1 When the channel name is not programmed, the selected zone and channel number are displayed.
(example: 1- 1) When the programmed channel is less than 10, you can select a channel without pushing [#]. For your reference:
You may be able to select a channel in the Menu screen, depending on the presetting. See section 5 for details. 2-4 2 BASIC OPERATION Receiving q Select a channel. (p. 2-4) Push [CH/GID Up] or [CH/GID Down]. Push one of the direct channel select keys, [Direct CH/GID 1] to [Direct CH/GID 5]. Push the [0] to [9] digit keys of the optional DTMF microphone to enter the channel number when the Channel Entry function is assigned to the key-
pad, or after pushing [Channel Entry]. w When receiving a call, rotate [VOL] to adjust the au-
dio output volume level. Setting the squelch level D The squelch circuit mutes the received audio, depend-
ing on the signal strength. q w Push [MENU]. Opens the Menu screen. Push [P2](
has the SQL LEVEL item. (Default: UTILITY)
) or [P3]() to select the category that UTILITY e r Push [P1](ENT). Enters the Menu Item Select mode. Push [P2](
item.
) or [P3]() to select the SQL LEVEL UTILITY SQL LEVEL t y Push [P1](ENT). Enters the Squelch Level Adjustment mode. Push [UP] to increase the squelch level up to 9 (tight squelch) or push [DOWN] to decrease the squelch level down to 0 (loose squelch). Push [P0](BACK) to return to the previous screen. LEVEL 9 u After setting, push [P1](EXIT). Closes the Menu screen. 2-5 2 BASIC OPERATION Transmitting Wait until the channel is clear to avoid interference. q w e Take the microphone off-hook. While scanning, the scan stops. Wait for the channel to become clear. The channel is busy when the LED indicator lights green. While holding down [PTT], speak at a normal voice level. Release [PTT] to receive. r NOTE:
To maximize the readability of your signal:
1. After pushing [PTT], pause briefly before you start speaking. 2. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak at your normal voice level. D Transmitting notes Transmit inhibit function The transceiver has several inhibit functions which re-
strict transmission under the following conditions:
- The channel is busy.
- An unmatched CTCSS tone or DTCS code is re-
ceived, depending on the presetting.
- An unmatched or matched RAN code is received, depending on the presetting.
- The selected channel is a receive only channel. Time-out timer (TOT) After continuous transmission for a preset time pe-
riod, the time-out timer causes the transceiver to stop transmitting. TOT Rekey timer Once transmission is cut OFF, it is further inhibited for a period determined by the TOT Rekey timer. MDC 1200 system operation The MDC 1200 signaling system enhances your trans-
ceivers capabilities. It allows PTT ID signaling. When you push or release [PTT], the transceiver sends your unit ID, if preset. ID 0001 When receiving a PTTID from unit ID 0001. 2-6 Section 3 ADVANCED OPERATION D D D D D Manual Dialing Autodial Stun function Editing the Autodial list Adding an entry to the Autodial list DTMF Calls ...............................................................................3-2
.........................................................................3-2
...................................................................................3-2
...........................................................................3-2
............................................................3-3
..........................................3-4 Emergency Calls ......................................................................3-5
.....................................................................3-5
..................................................3-5 Scrambler .................................................................................3-6 Radio Access Number (RAN) .................................................3-7 Emergency Calls Lone Worker Emergency Call D D 3-1 3 ADVANCED OPERATION DTMF Calls D Manual Dialing While holding down [PTT], push the keys on the 10-keypad to send the desired DTMF tones. When [Keypad Auto PTT] is assigned to the keypad, you can send the DTMF tones using the DTMF keypad with-
out pushing [PTT]. Autodial D Autodial allows you to quickly send DTMF tones that have been pre-entered onto your transceiver.
[UP] [DOWN]
q w e Push [Autodial]. The first entry in the Autodial list appears. Push [UP] or [DOWN] to select your desired num-
ber. Push [P3](TX) or [PTT] to send. For your reference:
When the Store & Send function is enabled, you can sequentially send up to 30 of DTMF tones at one time.
[P0], [P1], [P2], [P3]
q w e r Push [Autodial]. CODE? appears. Push [UP] or [DOWN] to enter a digit, and then push [P1](SEL) to set. Goes to the next digit entry position. You can use the 10-keypad keys of the optional DTMF microphone to enter a digit. Repeat step Push [P0](DEL) to delete the entered digit. Push [P1](EXIT) to exit the DTMF Code Entry mode. Push [P2](MODE) to toggle between the DTMF Code Entry mode and the DTMF Autodial code selection mode. Push [P3](TX) or [PTT] to send. w until you enter up to 30 digits. Stun function D When the transceiver receives a stun code over the air, the stun function is activated and the transceiver opera-
tion is inhibited. In this case, receiving a revive code is necessary to operate the transceiver again. This function is used when a transceiver is stolen or lost. 3-2 3 ADVANCED OPERATION DTMF Calls (Continued) D q Editing the Autodial list Push [Autodial Programming]. AUTDIAL PRGM AUTODIAL 1 w e Push [UP] or [DOWN] to select the number you want to edit. Push [P1](ENT). Enters the Name Entry mode. o Push [P1](ENT) to set. OVERWRITE? appears. OVERWRITE?
!0 Push [P1](OK) to overwrite. Push [P0](BACK) to return to the DTMF Code Entry mode. AUTODIAL 1 AUTDIAL PRGM AUTODIAL 2 r t Push [UP] or [DOWN] to enter a character, and then push [P1](SEL) to set. Goes to the next character entry position. You can use the 10-keypad keys of the optional DTMF microphone to enter a character. Repeat step characters. Push [P0](DEL) to delete a character. Push [P2]() or [P3]() left or right to select a charac-
r until you enter a name of up to 12 ter. AUTODIAL 2 y Push [P1](ENT) to save. Enters the DTMF Code Entry mode. 11111 u i Push [UP] or [DOWN] to enter a digit, and then push
[P1](SEL) to set. Goes to the next digit entry position. You can use the 10-keypad keys of the optional DTMF microphone to enter a digit. Repeat step to 16 digits. Push [P0](DEL) to delete a digit. u until you enter a DTMF number of up 11112 3-3 3 ADVANCED OPERATION DTMF Calls (Continued) D q Adding an entry to the Autodial list Push [Autodial Programming]. AUTDIAL PRGM AUTODIAL 1 w Push [UP] or [DOWN] to select a blank number. AUTDIAL PRGM BLANK 04 u i Push [UP] or [DOWN] to enter a digit, and then push
[P1](SEL) to set. Goes to the next digit entry position. You can use the 10-keypad keys of the optional DTMF microphone to enter a digit. Repeat step to 16 digits. Push [P0](DEL) to delete a digit. u until you enter a DTMF number of up 12345 e Push [P1](ENT). Enters the Name Entry mode. NAME? appears. o Push [P1](ENT) to set. STORE? appears. NAME?
STORE?
!0 Push [P1](OK) to store. Push [P0](BACK) to return to the DTMF Code Entry mode. AUTDIAL PRGM AUTODIAL 4 r t Push [UP] or [DOWN] to enter a character, and then push [P1](SEL) to set. Goes to the next character entry position. You can use the 10-keypad keys of the optional DTMF microphone to enter a character. Repeat step characters. Push [P0](DEL) to delete a character. Push [P2]() or [P3]() left or right to select a charac-
r until you enter a name of up to 12 ter. AUTODIAL 4 y Push [P1](ENT) to set. Enters the DTMF Code Entry mode. CODE? appears. CODE?
3-4 3 ADVANCED OPERATION Emergency Calls Emergency Calls D When [Emergency] is assigned to [R], you can manu-
ally make an Emergency call. q w R] for 1 second. Hold down [
Enters the Emergency mode. When the transceiver enters the Emergency mode, it will change to the Emergency channel and begin transmit-
ting, according to the presetting. To exit from the Emergency mode, hold down [
again, or turn OFF the power. If the Emergency mode completes a preset number of call cycles, the transceiver will automatically exit the mode and return to the zone and channel that was in use before you entered the Emergency mode. R]
NOTE:
The Emergency Mode Type can be set to Silent or Audible by using the optional cloning software. When Audible is set, the transceiver sounds a beep when transmitting in the Emergency mode. Lone Worker Emergency Call D When the Lone Worker function is activated, the Emer-
gency function is automatically turned ON, after the preset time period has passed with no operation per-
formed. Push [Lone Worker] to turn the function ON or OFF.
[R]
3-5 3 ADVANCED OPERATION Scrambler The Voice Scrambler function provides private commu-
nication between stations. All transceiver versions have a built-in scrambler. Push [Scrambler/Encryption] to turn the function ON or OFF. After turning ON the function, push [PTT] to make an appears when the Scrambler function is ON. encrypted call. q Changing the Scrambler code setting:
Hold down [Scrambler/Encryption Code] to enter the Scrambler Code Setting mode. The length of time you hold down [Scrambler/Encryption w e Code] may differ, depending on the presetting. Push [UP] or [DOWN] to select a desired code. Push [P1](EXIT) to save and exit. Even if the Scrambler function is OFF in step q, it auto-
matically turns ON after exiting the Scrambler Code set-
ting mode. 3-6 3 ADVANCED OPERATION Radio Access Number (RAN) RAN is a signaling system designed for digital radio communications. When a channel is set up with a RAN, the squelch will open only when a call containing a matching RAN is received. If a call containing a different RAN is made on the same channel you are using, you will not hear the call. 3-7 Section 4 SCAN OPERATION Scan operation .........................................................................4-2 Temporary channel lockout ....................................................4-3 Priority scan .............................................................................4-4
........................................................4-4 Scan Revert channel ...............................................................4-5 Scan delete/add .......................................................................4-6 Setting a Priority channel D 4-1 4 SCAN OPERATION Scan operation A scan monitors for signals on the transceiver channels. While scanning, the transceiver checks for a signal on each channel and stops when a signal is received. appears while scanning. Push [Scan] each time to start or stop a scan. When the transceiver detects a signal, the scan pauses on the channel. The transceiver remains on the busy channel until the signal disappears, and then the scan resumes. SCAN While scanning NOTE: Two or more channels must be programmed to start a scan. For your reference:
Before starting a scan, set the following items:
Set 3 scan types in the transceiver: Single, Multi or List. Set the scan type in both the conventional and trunk-
ing zones. Set Priority channels, but only in conventional type zones. When you select a conventional zone, trunking zones are not scanned. When you select a trunking zone, conventional zones are not scanned. Select the desired zone to start scanning. Single: The transceiver scans the preset target channels or GIDs in only the selected zone. For a Priority scan, all Priority channels will also be scanned, even if they are in other conventional type zones. Multi: The transceiver scans the preset target channels or GIDs in only the preset target zones. For a Priority scan, all Priority channels will also be scanned, even if they are in other conventional type zones. The transceiver scans the preset target channels or GIDs in only the zones that are preset on the Scan List. For a Priority scan, all Priority channels will also be scanned, even if they are in conven-
tional type zones that are not on the List. List:
NOTE:
When the scan starts in the Conventional group zone, the NXDN Trunking system zone is not scanned. When the scan starts in the NXDN Trunking system zone, the Conventional group zone is not scanned. 4-2 4 SCAN OPERATION Temporary channel lockout During a scan, you can temporarily delete a channel from a scanning sequence. This function speeds up scanning by skipping unwant-
ed channels. q w Start the scan. (p. 4-2) When a signal is received, the scan pauses. While the scan is paused, and if you want to skip the frequency, push [Scan Delete/Add].
(scan target channel icon) disappears when the se-
lected channel is deleted from the scanning sequence. The channel is no longer scanned. However, depending on the presetting, the deleted channel may be added to the scan group again after the scan is cancelled. See also: Scan delete/add on page 4-6 4-3 4 SCAN OPERATION Priority scan The Priority scan scans all scan target channels or GIDs in the zone while also monitoring the Priority 1 and Priority 2 channels. When the scan is paused on the Priority 1 channel, the other channels are not monitored. Setting a Priority channel D Depending on the presetting, you can manually set a Priority channel (Priority 1, Priority 2 or Priority 1 & 2). q Select a channel that you want to set as a Priority channel. Channel 1 w Push [Priority-channel Select]. Enters the Priority Channel Setting mode. PRI CH SEL NORMAL e Push [UP] or [DOWN] to select PRIORITY 1, PRIORITY 2 or PRIORITY 1 & 2. PRI CH SEL PRIORITY 1 r Push [P1](OK). The selected channel is set as a Priority channel. NOTE: When PRIORITY 1 & 2 is selected, the same channel is set as both Priority 1 and Priority 2 channels. 4-4 4 SCAN OPERATION Scan Revert channel The Scan Revert channel is automatically selected when you push [PTT] to make a call during a scan. The Scan Revert channel can be set to the transceiver using the optional cloning software. Last Called + Selected:
The transceiver makes a call on the last channel or GID that you received a call on. However, if you push [PTT] while the scan is paused, the transceiver makes a call on the chan-
nel or to the GID that the scan is paused on. When you change the channel or GID before starting a scan, the transceiver makes a call on the selected channel or to the GID until the trans-
ceiver receives another call. Selected:
The transceiver makes a call on the channel or to the GID selected before a scan. Selected + Talkback:
The transceiver makes a call on the channel or to the GID selected before a scan. However, if you push [PTT] when the scan is paused, the transceiver makes a call on the chan-
nel or to the GID that the scan is paused on. Priority 1:
The transceiver makes a call on the Priority 1 channel. Priority 1 + Talkback:
The transceiver makes a call on the Priority 1 channel. However, if you push [PTT] when the scan is paused, the transceiver makes a call on the chan-
nel or to the GID that the scan is paused on. Priority 2:
The transceiver makes a call on the Priority 2 channel. Priority 2 + Talkback:
The transceiver makes a call on the Priority 2 channel. However, if you push [PTT] when the scan is paused, the transceiver makes a call on the chan-
nel or to the GID that the scan is paused on. 4-5 4 SCAN OPERATION Scan delete/add During scan, you can temporarily delete a channel or zone from the scanning sequence. q w Select a channel, GID or zone that you want to de-
lete from the sequence. Push [Scan Delete/Add]. disappears when the selected channel, GID or zone is deleted from the scanning sequence. Channel 1 To manually add a channel, GID or zone to the scan-
ning sequence, repeat steps q and w. appears when the selected channel is added to the sequence. 4-6 Section 5 MENU SCREEN Menu screen description ........................................................5-2
.......................................................5-2 Menu functions ........................................................................5-3 Entering the Menu screen D 5-1 5 MENU SCREEN Menu screen description When [Menu] is assigned, you can open the Menu screen. In the Menu screen, the items are categorized. Depending on the presetting, you can select various functions and adjust the transceiver settings in the Menu screen. CONTACT Menu screen (Sample) Entering the Menu screen D Example: Setting the squelch level q w Push [MENU]. Opens the Menu screen. Push [P2](
has the SQL LEVEL item. (Default: UTILITY)
) or [P3]() to select the category that UTILITY e r Push [P1](ENT). Enters the Menu Item Select mode. Push [P2](
item.
) or [P3]() to select the SQL LEVEL UTILITY SQL LEVEL t y Push [P1](ENT). Enters the Squelch Level Adjustment mode. Push [UP] to increase the squelch level up to 9 (tight squelch), or push [DOWN] to decrease the squelch level down to 0 (loose squelch). Push [P0](BACK) to return to the previous screen. LEVEL 9 u After setting, push [P1](EXIT). Closes the Menu screen. For your reference:
You can close the Menu screen by pushing [R], even if an item is selected. 5-2 5 MENU SCREEN Menu functions Autodial AUTO DIAL Opens the DTMF Autodial code selection screen. q w e When the Store & Send function is enabled:
q w When AUTO DIAL is displayed, push [P1](ENT). The first entry in the Autodial list appears. Push [UP] or [DOWN] to select a desired number. Push [P3](TX) to send. When AUTO DIAL is displayed, push [P1](ENT). CODE? appears. Push [UP] or [DOWN] to enter a digit, and then push
[P1](SEL) to set. Goes to the next digit entry position. You can use the 10-keypad keys on the optional DTMF microphone. Repeat step Push [P0](DEL) to delete the entered digit. Push [P1](EXIT) to exit the DTMF Code Entry mode. Push [P2](MODE) to toggle between the DTMF Code En-
w until you enter up to 30 digits. e try mode and the DTMF Autodial code selection mode. Push [P3](TX) to send. r Autodial Programming AUTDIAL PRGM Enters the DTMF Code Programming mode. q w e When AUTDIAL PRGM is displayed, push [P1](ENT). The first entry in the Autodial list appears. Push [UP] or [DOWN] to select a desired number. Push [P1](ENT). Enters the Name Entry mode. (p. 3-3) AUX A AUX A Turns the AUX A port ON or OFF. q w e When AUX A is displayed, push [P1](ENT). Push [UP] or [DOWN] to select ON or OFF. Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. AUX B AUX B Turns the AUX B port ON or OFF. q w e When AUX B is displayed, push [P1](ENT). Push [UP] or [DOWN] to select ON or OFF. Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. Broadcast BROADCAST In the NXDN Trunking system Turns the Broadcast Call ON or OFF. This item can also be used to make a Broadcast Group Call. q w e When BROADCAST is displayed, push [P1](ENT). Push [UP] or [DOWN] to select ON or OFF. Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. When ON is selected in step w, push [PTT] to send the Broadcast Group Call. Direct CH/GID 1 Select to Direct CH/GID 5 Select DIRECT CHGD1 to DIRECT CHGD5 Sets the selected channel or GID to a Direct CH/GID between 1 and 5. q w e Select a desired channel. (p. 2-4) Push [MENU]. Opens the Menu screen. When a channel between DIRECT CHGD1 and DIRECT CHGD5 is displayed, push [P1](ENT). Sets the selected channel to a Direct channel between 1 and 5. Display Format DISP FORMAT In the Analog mode or NXDN Conventional system Toggles the display format between the channel name and the zone and channel number. In the NXDN Trunking system Toggles the display format between the GID name and the GID number. q When DISP FORMAT is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select CH NAME or ZONE-CH No. Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. e w External Speaker EXT SPEAKER Turns the External speaker function ON or OFF. When the External speaker function is ON, the PA speaker that is connected to the D-Sub 15-pin will ac-
tivate. q w e When EXT SPEAKER is displayed, push [P1](ENT). Push [UP] or [DOWN] to select ON or OFF. Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. 5-3 Group + SDM (NXDN) GROUP+SDM In the NXDN Conventional system or the NXDN Trunking system Enters the Group Call mode, and then the Short Data Message Entry mode. q w e r When GROUP+SDM is displayed, push [P1](ENT). Push [UP] or [DOWN] to select a desired GID. Push [P1](ENT). Enters the Short Data Message Entry mode. Push [UP] or [DOWN] to enter a character, and then push [P1](SET) to set. Goes to the next character entry position. You can use the 10-keypad keys on the optional DTMF microphone. Repeat step 100 characters. Push [P0](DEL) to delete a character. Push [P2]() or [P3]() left or right to select a charac-
r until you enter a message of up to t y ter. Push [PTT] to send the message to the selected GID. Group + Status (NXDN) GROUP+STATUS In the NXDN Conventional system or the NXDN Trunking system w Enters the Group Call mode, and then the Status Mes-
sage Entry mode. q When GROUP+STATUS is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select a desired GID, and then push [P1](ENT). Enters the Status Message Selection mode. Push [UP] or [DOWN] to select the status message that you want to send. If you want to directly enter a status message, push [P2]
e
(MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. You can use the 10-keypad keys on the optional DTMF microphone. Push [P3](TX) to send the message to the selected GID. r 5 MENU SCREEN Menu functions (Continued) Fixed Volume FIXED VOLUME Toggles the tone level between High and Low, or turns OFF the tone. q When FIXED VOLUME is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select LOW, HIGH or OFF. Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. e w Forced Search FORCE SEARCH In the NXDN Trunking system Starts to search for a site. When FORCE SEARCH is displayed, push [P1]
(ENT). Displays SEARCHING. GPS Position Display GPS POS DISP Enters the GPS Position Display mode. In the GPS Position Display mode, you can check your latitude and longitude position. q When GPS POS DISP is displayed, push [P1]
(ENT). You can check your latitude and longitude position. Push [UP] or [DOWN] to toggle between the latitude and longitude position display. Push [P0](BACK) to return to the previous screen. Push [P1](EXIT) to the GPS Position Display mode. Push [P2](DISP) to automatically switch the latitude and w longitude position display. Group (NXDN) GROUP MODE In the NXDN Conventional system or the NXDN Trunking system Enters the Group Call mode. In the NXDN Conventional system, this function is used for Group Calls. In the NXDN Trunking system, the Group ID List is dis-
played, but the transceiver cannot make Group calls. q When GROUP MODE is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select a desired GID. Push [PTT] to call the selected GID. w e 5-4 5 MENU SCREEN Menu functions (Continued) High Transmit Power HI TX POWER In the NXDN Trunking system Toggles the transmit power level. When Auto is set as the default:
q w When HI TX POWER is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select ON (High) or OFF
(Auto). Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. e When Low is set as the default:
q When HI TX POWER is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select ON (High) or OFF
(Low). Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. See page 5-6 about [Low Transmit Power]. w e Home CH/GID Select HOME CHANNEL Sets the selected channel or GID as the Home Chan-
nel. q w e Select a desired channel. (p. 2-4) Push [MENU]. Opens the Menu screen. When HOME CHANNEL is displayed, push [P1]
(ENT). Sets the selected channel or GID as the Home Channel. Horn Alert HORN ALERT Turns the Horn Alert function ON or OFF. When this function is ON, the horn alert port will be ac-
tivated for a preset time period after receiving a call. q w e When Push [UP] or [DOWN] to select ON or OFF. Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. HORN ALERT is displayed, push [P1](ENT). Individual (NXDN) INDIVIDUAL Enters the Individual Call mode. q w When INDIVIDUAL is displayed, push [P1](ENT). Push [UP] or [DOWN] to select a desired unit ID. If you want to directly enter an unit ID, push [P2](MODE) to select the Unit ID Entry mode. e You can enter an unit ID between 1 and 65519. Push [P3](TX) to call to the selected unit ID. 5-5 Individual + SDM (NXDN) INDIV+SDM Enters the Individual Call mode, and then the Short Data Message Entry mode. q w When INDIV+SDM is displayed, push [P1](ENT). Push [UP] or [DOWN] to select a desired unit ID. If you want to directly enter an unit ID, push [P2](MODE) to select the Unit ID Entry mode. e r t You can enter an unit ID between 1 and 65519. Push [P1](ENT). Enters the Short Data Message Entry mode. Push [UP] or [DOWN] to enter a character, and then push [P1](SET) to set. Goes to the next character entry position. You can use the 10-keypad keys on the optional DTMF microphone. Repeat step 100 characters. Push [P0](DEL) to delete a character. Push [P2]() or [P3]() left or right to select a charac-
r until you enter a message of up to y ter. Push [PTT] to send the message to the selected unit ID. Individual + Status (NXDN) INDIV+STATUS Enters the Individual Call mode, and then the Status Message Entry mode. q w When INDIV+STATUS is displayed, push [P1](ENT). Push [UP] or [DOWN] to select a desired unit ID. If you want to directly enter an unit ID, push [P2](MODE) to select the Unit ID Entry mode. e e You can enter an unit ID between 1 and 65519. Push [P1](ENT). Enters the Status Message Selection mode. Push [UP] or [DOWN] to select a status message that you want to send. If you want to directly enter a status message, push [P2]
(MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. You can use the 10-keypad keys on the optional DTMF microphone. Push [P3](TX) to send the message to the selected unit ID. r LCD Brightness LCD BRIGHT Selects the brightness of the function display and keys backlight. Select High, Low or OFF to meet your needs. The function display and keys can be backlit for better visibility under low light conditions. q w When LCD BRIGHT is displayed, push [P1](ENT). Push [UP] or [DOWN] to select LOW, HIGH or OFF. Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. e 5 MENU SCREEN Menu functions (Continued) Lone Worker LONE WORKER Turns the Lone Worker function ON or OFF. (p. 3-5) q When LONE WORKER is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select ON or OFF. Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. w e Low Transmit Power LOW TX POWER In the Analog mode or NXDN Conventional system Toggles the transmit power between High and Low, if High is set as the default. q When LOW TX POWER is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select ON (Low) or OFF
(High). Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. e w w In the NXDN Trunking system Toggles the transmit power level. When the transmit power level is set to Auto as the default:
q When LOW TX POWER is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select ON (Low) or OFF
(Auto). Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. e When the transmit power level is set to High as the default:
q When LOW TX POWER is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select ON (Low) or OFF
(High). Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. See page 5-5 about [High Transmit Power]. e w Maintenance MAINTENANCE Enters the Maintenance Display mode. In the Maintenance Display mode, you can check the RSSI level of the selected channel for installation or maintenance of the system. q w When MAINTENANCE is displayed, push [P1](ENT). Displays the RSSI level. Push [P0](BACK) to return to the previous screen. Push [P1](EXIT) to exit. 5-6 Monitor MONITOR In the Analog mode Turns the Monitor ON or OFF. When the Monitor is ON, the transceiver releases the CTCSS mute. In the NXDN Conventional system Turns the Monitor ON or OFF. When the Monitor is ON, the transceiver releases the RAN code mute. q w e When MONITOR is displayed, push [P1](ENT). Push [UP] or [DOWN] to select ON or OFF. Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. Operator Selectable Tone OST Turns the OST (Operator Selectable Tone) mode ON or OFF. When the OST mode is ON, the selected tone in the OST list is enabled. q w e When OST is displayed, push [P1](ENT). Push [UP] or [DOWN] to select ON or OFF. Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. OST List OST LIST Displays the OST (Operator Selectable Tone) list. q When OST LIST is displayed, push [P1](ENT). Push [UP] or [DOWN] to select a desired OST tone w or turn OFF the OST tone. Push [P0](BACK) to return to the previous screen. Push [P1](EXIT) to exit. e Priority-channel Select PRI CH SEL Enters the Priority Channel Select mode for a Priority scan. q w e r Select a desired channel. (p. 2-4) Push [MENU]. Opens the Menu screen. When PRI CH SEL is displayed, push [P1](ENT). Push [UP] or [DOWN] to select PRIORITY 1, PRI-
ORITY 2, PRIORITY 1 & 2 or NORMAL. Push [P0](BACK) to return to the previous screen. Push [P1](OK). Sets the selected channel to Priority 1, Priority 2, Priority t 1 and 2 or a Normal channel. NOTE: When PRIORITY 1 & 2 is selected, the same channel is set as both Priority 1 and Priority 2 channels. 5 MENU SCREEN Menu functions (Continued) Public Address PUB ADDRESS Turns the Public Address function ON or OFF. When this function is ON, you can make announce-
ments through a PA speaker. Transmitting is disabled while in the PA mode. q When PUB ADDRESS is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select ON or OFF. Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. w e RX Audio Equalizer RX AUDIO EQ This function sets the audio characteristics type to ap-
ply to the received audio. q When RX AUDIO EQ is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select the option. Push [P0](BACK) to return to the previous screen. FLAT:
HIGH BOOST:
LOW BOOST:
Selects the standard audio characteristics. Suppresses the treble range and boosts the bass range. Emphasizes the treble range. w e Push [P1](EXIT) to save. RX Auto Gain Control RX AUTO GAIN This function automatically adjusts the received audio volume to an appropriate level so that you can clearly hear the audio. q When RX AUTO GAIN is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select the option. Push [P0](BACK) to return to the previous screen. OFF: Disables the Auto Gain Control. The received w audio level is only adjusted by [VOL]. HIGH: Enables the Auto Gain Control. The received audio level will be automatically adjusted to an appropriate constant level, according to the [VOL] setting. However, the background noise will be boosted, and howling may oc-
cur, depending on your operating environ-
ment. LOW: Enables the Auto Gain Control. The received audio level will be automatically adjusted to an appropriate constant level, according to the [VOL] setting. However, the adjust-
able gain is smaller than the HIGH setting. Therefore, background noise boosting will also be smaller, and howling may not occur. e Push [P1](EXIT) to save. 5-7 RX Low Cut RX LOW CUT While receiving a digital signal, this function cuts the frequency components at 300 Hz or below. q w e When RX LOW CUT is displayed, push [P1](ENT). Push [UP] or [DOWN] to select ON or OFF. Push [P0](BACK) to return to the previous screen. Push [P1](EXIT) to save. Scan SCAN Starts or stops a scan. q w e When SCAN is displayed, push [P1](ENT). Push [UP] or [DOWN] to select ON or OFF. Push [P0](BACK) to return to the previous screen. Push [P1](OK). A scan starts when ON is selected in step w. A scan stops when OFF is selected in step w. Scan Delete/Add SCAN DEL/ADD Sets or cancels the selected channel or GID as the scan target. q w e Select a desired channel. (p. 2-4) Push [MENU]. Opens the Menu screen. When SCAN DEL/ADD is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select DELETE or ADD. Push [P0](BACK) to return to the previous screen. Push [P1](OK). The selected channel is canceled as a scan target when r t DELETE is selected in step r. The selected channel is set as a scan target when ADD is selected in step r. Scrambler/Encryption SCRAM/ENCRYP In the Analog mode Turns the Scrambler function ON or OFF. In the NXDN Conventional system or the NXDN Trunking system Turns the Encryption function ON or OFF. q When SCRAM/ENCRYP is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select ON or OFF. Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. w e 5 MENU SCREEN Menu functions (Continued) Scrambler/Encryption Code SCRAM CODE In the Analog mode Enters the Scrambler Code Selection mode. In the NXDN Conventional system or the NXDN Trunking system Enters the Encryption Key Selection mode. q When SCRAM CODE is displayed, push [P1]
(ENT). The Scrambler or the Encryption function automatically turns ON. Push [UP] or [DOWN] to select a desired Scrambler code or Encryption key. Push [P0](BACK) to return to the previous screen. Push [P1](EXIT) to save. w e SDM (NXDN) SHRT MSG MOD In the NXDN Conventional system or the NXDN Trunking system w Directly enters the Short Message mode. q When SHRT MSG MOD is displayed, push [P1]
(ENT). MESSAGE? appears. Push [UP] or [DOWN] to enter a character, and then push [P1](SEL) to set. Goes to the next character entry position. You can use the 10-keypad keys on the optional DTMF microphone. Repeat step 100 characters. Push [P0](DEL) to delete a character. Push [P2]() or [P3]() left or right to select a charac-
w until you enter a message of up to e ter. Push [PTT] to send the message to the Base ID. Push [P1](EXIT) to exit. r t Send the GPS Data SND GPS DATA In the NXDN Conventional system or the NXDN Trunking system Sends the position data that is received from the GPS receiver to a Base station. q w When SND GPS DATA is displayed, push [P1](ENT). Push [P1](ENT) to send. Site Lock SITE LOCK In the NXDN Trunking system Turns the Site Lock function ON or OFF. q w e When SITE LOCK is displayed, push [P1](ENT). Push [UP] or [DOWN] to select ON or OFF. Push [P0](BACK) to return to the previous screen. Push [P1](OK) to save. 5-8 Site Number SITE No. In the NXDN Trunking system Display the current Site number. When SITE No. is displayed, push [P1](ENT). Displays the current Site number for 3 seconds, and then exits the Menu screen. Site Select SITE In the NXDN Trunking system Enters the Site Select mode. q w e When SITE is displayed, push [P1](ENT). Push [UP] or [DOWN] to select a desired site. Push [P0](BACK) to return to the previous screen. Push [P1](SEL) to save. Squelch Level SQL LEVEL In the Analog mode Enters the Squelch Level Adjustment mode. q w When SQL LEVEL is displayed, push [P1](ENT). Push [DOWN] to decrease the squelch level down to 0 (loose squelch), or push [UP] to increase the squelch level up to 9 (tight squelch). Push [P0](BACK) to return to the previous screen. Push [P1](EXIT) to exit. e Squelch Off SQL OFF In the Analog mode or the NXDN Conventional system Opens the squelch, and releases the mute. q w e When SQL OFF is displayed, push [P1](ENT). Push [UP] or [DOWN] to select ON or OFF. Push [P0](BACK) to return to the previous screen. Push [P1](OK) to exit. Stack STACK Enters the Memory Stack mode. q w When STACK is displayed, push [P1](ENT). Push [P0](BACK) to return to the previous screen. Push [UP] or [DOWN] to select a desired message. Push [P0](DEL) to delete the selected message. Push [P2](DISP) to change the display item between re-
ceived ID, message contents and channel number. Push [P1](EXIT) to exit. e 5 MENU SCREEN Menu functions (Continued) Status (NXDN) STATUS Directly enters the Status Message mode. q w When STATUS is displayed, push [P1](ENT). Push [UP] or [DOWN] to select a status message. If you want to directly enter a status message, push [P2]
(MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. You can use the 10-keypad keys on the optional DTMF microphone. Push [P3](TX) to send the message to the Base ID. Push [P1](EXIT) to exit. e r Talk Around TALK AROUND In the Analog mode Turns the talk around function ON or OFF. q When TALK AROUND is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select ON or OFF. Push [P1](OK) to save. w e Transceiver Password PASSWORD Enters the Password Entry mode. The transceiver cannot be used until you enter a cor-
rect password. q w When PASSWORD is displayed, push [P1](ENT). Enters the Password Entry mode. Push [UP] or [DOWN] to enter a digit code, and push [P1] to set. Goes to the next digit entry position. Repeat step then push [P1]. w until you enter the password, and e then When using the DTMF microphone:
Push the [0] to [9] digit keys on the microphone to enter the password, and then push [#]. NOTE: If PASSWORD does not disappear after pushing [P1], the password code you entered may be incorrect. In this case, enter the correct pass-
word. TX Audio Equalizer TX AUDIO EQ This function sets the audio characteristics type to ap-
ply to the transmit audio. q w When TX AUDIO EQ is displayed, push [P1](ENT). Push [UP] or [DOWN] to select the option. Push [P0](BACK) to return to the previous screen. FLAT:
HIGH BOOST:
Selects the standard audio characteristics. Selects the audio characteristics emphasizing the treble range. LOW BOOST:
Suppresses the treble range and boosts the bass range. e Push [P1](EXIT) to save. TX Auto Gain Control TX AUTO GAIN This function automatically adjusts the transmit audio level to an appropriate constant level so that the called station can hear the audio clearly. q w When TX AUTO GAIN is displayed, push [P1](ENT). Push [UP] or [DOWN] to select ON or OFF. Push [P0](BACK) to return to the previous screen. ON:
Enables the Auto Gain Control. The transmit audio level will be adjusted to an appropriate constant level. e OFF: Disables the Auto Gain Control. Push [P1](EXIT) to save. TX Noise Suppressor TX NOISE SUP This function enables transmitting while in the digital mode and reducing or eliminating the noise component in the background noise. q When TX NOISE SUP is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select ON or OFF. Push [P0](BACK) to return to the previous screen. Push [P1](EXIT) to save. w e Zone Delete/Add ZONE DEL/ADD Sets or cancels the selected zone as a scan target. q w e Select a desired zone. (p. 2-3) Push [MENU]. Opens the Menu screen. When ZONE DEL/ADD is displayed, push [P1]
(ENT). Push [UP] or [DOWN] to select DELETE or ADD. Push [P0](BACK) to return to the previous screen. Push [P1](OK). The selected zone is canceled as a scan target when DELETE is selected in step r. r t The selected zone is set as a scan target when ADD is selected in step r. 5-9 Section 6 NXDN OPERATION <COMMON>
NXDN system operation ..........................................................6-2 Memory Stack ..........................................................................6-3
......................................................6-3
....................................................6-4
..................................................6-4 Viewing a stored message Deleting a desired message Deleting all stored messages D D D 6-1 6 NXDN OPERATION <COMMON>
NXDN system operation NXDN is a Common Air Interface (CAI), the name for over-the-air methods by which transceivers and repeat-
ers communicate. NXDN defines the next-generation digital protocol. The NXDN system has two operating modes, conven-
tional and trunking. In an NXDN conventional system, you should manually search for a clear channel. In an NXDN trunking system, the repeater automati-
cally searches for a clear channel, and sends the infor-
mation to the transceivers. In addition, Type-C requires a Control Channel repeat-
er. If you use an NXDN transceiver, you can transmit and receive Individual Calls, Group Calls, Status Messages, Short Messages, and so on. 6-2 6 NXDN OPERATION <COMMON>
Memory Stack The transceiver has a Memory Stack. When the trans-
ceiver receives a Status Message or a Short Message, the received content is stored in the transceivers Mem-
ory Stack. If you turn OFF the transceivers power, the contents will be cleared. The stored messages are displayed using the following indication. Message type Information Caller ID Stack Status Message Short Message Stored number Stored number Display items Caller ID Message contents Received channel or GID Indication ID ST SM 01 to 15 ID MSG CH 6-3 D q Viewing a stored message When a transceiver receives data:
Displays DATA RCVD, COMPLETE, the received mes-
sage, the callers unit ID and GID*. w e r blinks.
*Displays only when the received call is a Group call. Push [Stack]. Enters the Memory Stack mode. Displays STACK. Push [UP] or [DOWN] to select a desired message. Push [P2](DISP) to change the displayed item be-
tween received ID, message contents and channel number. STACK SM01 ID STACK UID 0001 Received ID STACK SM01 MSG STACK SHORT MESSAG Message contents Scrolls STACK SM01 CH STACK CH CH01 Channel number t Push [P1](EXIT). Exits the Memory Stack mode. 6 NXDN OPERATION <COMMON>
Memory Stack (Continued) D q w e r Deleting a desired message Push [Stack]. Enters the Memory Stack mode. Displays STACK. Push [UP] or [DOWN] to select a desired message. Push [P0](DEL). Displays DELETE?. Push [P1](OK). Deletes the selected message. Push [P0](BACK) to return to the previous screen. Push [R] to exit the Memory Stack mode. D q w e Deleting all stored messages Push [Stack]. Enters the Memory Stack mode. Displays STACK. Hold down [P0](DEL) for 1 second. Displays ALL DELETE?. Push [P1](OK). Deletes all messages. Push [P0](BACK) to return to the previous screen. Push [R] to exit the Memory Stack mode. 6-4 Section 7 NXDN OPERATION <TRUNKING MODE>
D D D Selecting a GID Selecting a Home GID Directly entering a GID NXDN trunking operation ........................................................7-2 Selecting a GID (Group ID) .....................................................7-3
......................................................................7-3
.............................................................7-3
............................................................7-3 Transmitting a call ...................................................................7-4
..........................................7-4
.....................................7-5
................................................7-6
...........................................7-6
...............................................................7-7
................................................................................7-7
.........................................................................7-8
.........................................................................7-8
.........................................................................7-9 Group call (Transmission Trunked) Individual call (Transmission Trunked) Group call (Message Trunked) Individual call (Message Trunked) Broadcast Group call Status call Short Data call Long Data call Telephone call D D D D D D D D D Receiving a call ........................................................................7-10
................................................................................7-10
...........................................................................7-10
...............................................................7-11
................................................................................7-11
.........................................................................7-12
.........................................................................7-12
.........................................................................7-13 Forced Search ..........................................................................7-14 Group call Individual call Broadcast Group call Status call Short Data call Long Data call Telephone call D D D D D D D 7-1 7 NXDN OPERATION <TRUNKING MODE>
NXDN trunking operation When you select the NXDN Trunking system mode, your transceiver automatically searches for, and se-
lects a clear channel. To use the NXDN Trunking system mode, your trans-
ceiver must register to a Control Channel repeater. Before operating in the NXDN Trunking system mode, select the NXDN Trunking System zone. (p. 2-3) 7-2 7 NXDN OPERATION <TRUNKING MODE>
Selecting a GID Selecting a GID (Group ID) D To select a desired GID, do one of the following:
Push [CH/GID Up] or [CH/GID Down]. Push one of the direct GID select keys, [Direct CH/
GID 1] to [Direct CH/GID 5]. You can change the GID that is selected by push-
ing [Direct CH/GID 1] to [Direct CH/GID 5], as de-
scribed below. Changing the Direct GID setting:
q w Select a desired GID. Hold down one of the [Direct CH/GID 1] to [Direct CH/GID 5] keys for 3 seconds to set the selected GID to the Direct GID 1 to 5. Selecting a Home GID D The Home GID is the most often-used ID, and you can preset it into the transceiver. Push [Home CH/GID]. You can change the Home GID, as described be-
low. Changing the Home GID setting:
q w Select a desired GID. Hold down [Home CH/GID Select] for 3 seconds to set the selected GID to the Home GID. Directly entering a GID D You can select a GID by pushing [UP] or [DOWN], or the [0] to [9] digit keys on the microphone, after pushing
[Channel Entry]. Or, when the Channel Entry function is assigned to the keypad, you can select a GID by pushing the [0] to [9]
digit keys. q Push [Channel Entry] to enter the GID Entry mode. CH ENTER MOD CH No. _ _ w Push [UP] or [DOWN] to select the GID, and then push [P1](SEL). Push [P0](BACK) to cancel the entry, and return to the screen that you selected before entering the GID Entry mode. GR 1 When the GID name is not programmed, the select-
ed zone and channel number are displayed.
(example: 1- 1) When using the DTMF microphone:
q Push the [0] to [9] digit keys to enter the GID Entry mode. CH ENTER MOD CH No. _ 1 w Enter the GID number, and then push [#]. Push [M] to delete the entered number. Push [M] again to cancel the entry, and return to the screen that you selected before entering the GID Entry mode. GR 1 When the GID name is not programmed, the se-
lected zone and channel number are displayed.
(example: 1- 1) When less than 9 GIDs are programmed in the zone, you can select a GID without pushing [#] in step w. 7-3 7 NXDN OPERATION <TRUNKING MODE>
Group call (Transmission Trunked) Transmitting a call D When you select an NXDN Trunking System zone and a desired GID, you can transmit a Group call by simply pushing [PTT]. When you set GID to ALL, you can call all transceiv-
ers. Push [PTT] to make a Group call. For your reference:
When [Group + SDM (NXDN)] or [Group + Status
(NXDN)] is assigned, you can also send a message along with a Group call. w e r To send a Short Data Message along with a Group call. q Push [Group + SDM (NXDN)] to enter the GID Se-
lect mode. Displays SELCALL. Push [UP] or [DOWN] to select a desired GID. Push [P1](ENT). Enters the Short Data Message Entry mode. Push [UP] or [DOWN] to enter a character, and then push [P1](SET) to set. Goes to the next character entry position. You can use the 10-keypad keys on the microphone. Repeat step 100 characters. Push [P0](DEL) to delete a character. Push [P2]() or [P3]() left or right to select a charac-
r until you enter a message of up to t ter. SHORT MESSAG y u Push [PTT] to send the message to the selected GID. Push [P1](EXIT) to exit. To send a Status Message with a Group call. q Push [Group + Status (NXDN)] to enter the GID Se-
lect mode. Displays SELCALL. Push [UP] or [DOWN] to select a desired GID. Push [P1](ENT). Enters the Status Message Entry mode. Push [UP] or [DOWN] to select a desired status message. If you want to directly enter a status message, push [P2]
w e r
(MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. You can use the 10-keypad keys on the microphone. STATUS STATUS 001 t y Push [P3](TX) or [PTT] to send the message to the selected GID. Push [P1](EXIT) to exit. 7-4 7 NXDN OPERATION <TRUNKING MODE>
Transmitting a call (Continued) Individual call (Transmission Trunked) D You can call a specified station that is set to the same unit ID by using the Individual call function. q Push [Individual (NXDN)] to enter the Unit ID Select mode. Displays SELCALL. SELCALL UID 0001 w Push [UP] or [DOWN] to select a desired unit ID. If you want to directly enter an unit ID, push [P2](MODE) to select the Unit ID Entry mode. e r You can enter an unit ID between 1 and 65519. Push [P3](TX) or [PTT] to make an Individual call. Push [P1](EXIT) to exit. For your reference:
When [Individual + SDM (NXDN)] or [Individual + Sta-
tus (NXDN)] is assigned, you can also send a mes-
sage along with an Individual call. w e r To send a Short Data Message along with an Individ-
ual call. q Push [Individual + SDM (NXDN)] to enter the unit ID Select mode. Displays SELCALL. Push [UP] or [DOWN] to select a desired unit ID. Push [P1](ENT). Enters the Short Data Message Entry mode. Push [UP] or [DOWN] to enter a character, and then push [P1](SET) to set. Goes to the next character entry position. You can use the 10-keypad keys on the microphone. Repeat step 100 characters. Push [P0](DEL) to delete a character. Push [P2]() or [P3]() left or right to select a charac-
r until you enter a message of up to t ter. SHORT MESSAG y u Push [PTT] to send the message to the selected unit ID. Push [P1](EXIT) to exit. To send a Status Message with an Individual call. q Push [Individual + Status (NXDN)] to enter the unit ID Select mode. Displays SELCALL. Push [UP] or [DOWN] to select a desired unit ID. Push [P1](ENT). Enters the Status Message Entry mode. Push [UP] or [DOWN] to select a desired status message. If you want to directly enter a status message, push [P2]
w e r
(MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. You can use the 10-keypad keys on the microphone. STATUS STATUS 001 t y Push [P3](TX) or [PTT] to send the message to the selected unit ID. Push [P1](EXIT) to exit. 7-5 7 NXDN OPERATION <TRUNKING MODE>
Transmitting a call (Continued) Group call (Message Trunked) D When the Trunking type is set to Message Trunked, and after making a Group call, the transceiver contin-
ues to be linked to the traffic channel for a preset time period. While linked, the transceivers occupy the traffic chan-
nel, and you can call by simply pushing [PTT]. Individual call (Message Trunked) D When the Trunking type is set to Message Trunked, and after making an Individual call, the transceiver con-
tinues to be linked to the traffic channel for a preset time period. While linked, the transceivers occupy the traffic chan-
nel, and you can call by simply pushing [PTT]. When you select the NXDN Trunking System zone and a desired GID, you can transmit a Group call by simply pushing [PTT]. When you set GID to ALL, you can call all transceiv-
ers. Push [PTT] to make a Group call. q Push [Individual (NXDN)] to enter the Unit ID Select mode. Displays SELCALL. SELCALL UID 0001 w Push [UP] or [DOWN] to select the desired unit ID. If you want to directly enter an unit ID, push [P2](MODE) to select the Unit ID Entry mode. e r You can enter an unit ID between 1 and 65519. Push [P3](TX) or [PTT] to make an Individual call. Push [P1](EXIT). For your reference:
When [Group + SDM (NXDN)] or [Group + Status
(NXDN)] is assigned, you can send a message along with a Group call. See page 7-4 for details. For your reference:
When [Individual + SDM (NXDN)] or [Individual + Sta-
tus (NXDN)] is assigned, you can send a message along with an Individual call. See page 7-5 for details. 7-6 7 NXDN OPERATION <TRUNKING MODE>
Transmitting a call (Continued) Broadcast Group call D When you use the Broadcast Group call function, you can transmit a signal to transceivers that are set to the same Group ID. When you set GID to ALL, you can make the Broad-
cast Group call to all transceivers. q w Select a desired GID. (p. 7-3) Push [Broadcast] once or twice to select BRDCAST ON. BRDCAST ON e Push [PTT] to make a Broadcast Group call. Status call D The Status call is a simple message function to trans-
mit and receive a status message. A transceiver can display the status message quickly. You cannot transmit a voice signal at the same time. q w Push [Status (NXDN)] to enter the Status Message Select mode. Displays STATUS. Push [UP] or [DOWN] to select a desired status message. If you want to directly enter a status message, push [P2]
(MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. You can use the 10-keypad keys on the microphone. STATUS STATUS 001 e Push [P3](TX) or [PTT] to send the selected Status Message. Displays SEND DATA and then COMPLETE. 7-7 7 NXDN OPERATION <TRUNKING MODE>
Transmitting a call (Continued) Short Data call D You can send a Short Data message of up to 100 char-
acters. If you turn OFF the transceivers power, the message is cleared. Long Data call D You can send a Long Data message of up to 4,096 characters only by using an external device, such as a PC. You cannot send a Long Data message by pushing
[PTT]. q Push [SDM (NXDN)] to enter the Short Data Mes-
sage Entry mode. Displays MESSAGE?. MESSAGE?
w e Push [UP] or [DOWN] to enter a character, and then push [P1](SET) to set. Goes to the next character entry position. You can use the 10-keypad keys on the microphone. Repeat step 100 characters. Push [P0](DEL) to delete a character. Push [P2]() or [P3]() left or right to select a charac-
w until you enter a message of up to ter. SHORT MESSAG e r Push [PTT] to send. Displays SEND DATA and then COMPLETE. Push [P1](EXIT) to exit. If you exit from the Short Data Message Entry mode, and then you want to send the message again, do the following steps. q Push [SDM (NXDN)] to enter the Short Data Mes-
sage Entry mode. Displays the entered message. Displays the last part of the message if the message is over 12 characters. HORT MESSAGE w e Push [PTT] to send. Displays SEND DATA and then COMPLETE. Push [P1](EXIT) to exit. 7-8 7 NXDN OPERATION <TRUNKING MODE>
Transmitting a call (Continued) Telephone call D If you use the Telephone Call function, you can com-
municate with a telephone through the telephone lines
(PSTN, PABX, and so on). You can call from a transceiver to a telephone, or call from a telephone to a transceiver. q w e Push [Autodial]. The first entry in the Autodial list appears. Push [UP] or [DOWN] to select your desired tele-
phone number. Push [P3](TX) or [PTT] to start a Telephone call Displays CALLING. Displays PHONE CALL when the transceiver connects to the telephone line. r t Displays INVALID when the transceiver cannot connect to the line. Hold down [PTT] to talk. The telephone line will disconnect when you push
[R] or microphones [M], or when the microphone is on-hook (depending on the presetting). 7-9 7 NXDN OPERATION <TRUNKING MODE>
Group call Receiving a call D When you receive a Group call that includes a matched GID, your transceiver informs you of the call by sound-
ing beeps and blinking on the function display. In addition, you can easily call back to the calling station. Individual call D When you receive an Individual call that includes your unit ID, your transceiver informs you of the call by sounding beeps and blinking on the function dis-
play. In addition, you can easily call back to the calling station. q When you receive a Group call that includes a matched GID:
Beeps sound. Displays the callers unit ID and GID. blinks for about 10 seconds. UID 0001 GID 0002 q When you receive an Individual call that includes your unit ID:
Beeps sound. Displays the callers unit ID.*
* Alternately displays the callers unit ID and INCOMING, when you receive a Message Trunked type call, and the Automatic Response function is OFF. blinks for about 10 seconds. w To call back to the caller station, push [PTT] while is blinking. UID 0001 w To call back to the caller station, push [PTT] while is blinking. 7-10 7 NXDN OPERATION <TRUNKING MODE>
Receiving a call (Continued) Broadcast Group call D When a Broadcast Group Call is made, the transceiv-
ers with the same selected Group ID will receive the call. You cannot transmit a reply to the calling transceiver. When your transceiver receives a Broadcast Group Call, beeps sound. While your transceiver is receiving the call, the musical tone icon blinks on the function display. Status call D When you receive a Status call, your transceiver dis-
plays a received status message on the function display. The received message is stored in the Memory Stack, and you can view the message contents in the memory.
(p. 6-3) When you receive a Status call:
Beeps sound. Displays DATA RCVD, COMPLETE, the received mes-
sage, the callers unit ID and GID*.
*Displayed only when the received call is a Group call. The message is stored in the Memory Stack. blinks on the function display. COMPLETE STATUS 001 UID 0001 GID 0002 7-11 Long Data call D You can receive a Long Data message of up to 4,096 characters. The message can be output to a PC or ex-
ternal device from your transceiver. 7 NXDN OPERATION <TRUNKING MODE>
Receiving a call (Continued) Short Data call D When you receive a Short Data message, your trans-
ceiver displays the message on the function display. The message is stored in the Memory Stack, and you can view the message in the memory. (p. 6-3) When you receive a Short Data message:
Beeps sound. Displays DATA RCVD, COMPLETE, the received mes-
sage, the callers unit ID and GID*.
*Displayed only when the received call is the Group call. The message is stored in the Memory Stack. blinks on the function display. DATA RCVD COMPLETE SHORT MESSAG Scrolls when the re-
ceived message is over 12 characters. UID 0001 GID 0002 7-12 7 NXDN OPERATION <TRUNKING MODE>
Receiving a call (Continued) Telephone call D When you receive a call from a telephone, you can com-
municate with it through the telephone lines (PSTN, PABX, and so on). When a telephone calls your transceiver, the transceiv-
er sounds beeps, and then PHONE is displayed on the function display. Hold down [PTT] to talk to the telephone. 7-13 7 NXDN OPERATION <TRUNKING MODE>
Forced Search If you use the Forced Search function, the transceiver searches for other Control channels using the following hunt sequences. Hunt sequence Explanation Preferential Hunt Sequence Normal Hunt Sequence System Add Channel Sequence Site Hunt Sequence Comprehensive Hunt Sequence The transceiver searches for a Control channel that is set as the Preferential Hunt Control channel. The transceiver selects this Control channel with a high priority. The transceiver searches for a Control channel that is set as the Normal Hunt Control channel. The transceiver searches for up to 8 Control channels that are added by the system. The transceiver searches for a Control channel that is set as the Site Hunt Control channel in each site. The transceiver searches for a Control channel that is set in the network frequency table. q w e Hold down [Forced Search Function] for 2 seconds to turn ON the Forced Search Function. Displays the current site number. The transceiver starts to search for a Control chan-
nel signal. Displays SEARCHING. When the transceiver finds and registers to a control channel, the normal screen is displayed on the func-
tion display. 7-14 Section 8 NXDN OPERATION <CONVENTIONAL MODE>
D D D D D D Group call Individual call Individual Call Acknowledge Request call Status call Short Data call Long Data call NXDN Conventional operation ...............................................8-2 Transmitting a call ...................................................................8-3
................................................................................8-3
...........................................................................8-4
...............................8-4
................................................................................8-5
.........................................................................8-5
.........................................................................8-5 Receiving a call ........................................................................8-6
................................................................................8-6
...........................................................................8-6
...............................8-7
................................................................................8-7
.........................................................................8-8
.........................................................................8-8 Mixed Mode ..............................................................................8-9 Group call Individual call Individual Call Acknowledge Request call Status call Short Data call Long Data Call D D D D D D 8-1 8 NXDN OPERATION <CONVENTIONAL MODE>
NXDN Conventional operation When you select the NXDN Conventional system mode, you must manually search for and select a clear channel. The system setup is easier than the Trunking mode. 8-2 8 NXDN OPERATION <CONVENTIONAL MODE>
Group call Transmitting a call D When you select the NXDN Conventional System zone, you can make a Group call by using the Group Call function. Set GID to ALL, to call all transceivers. q Push [Group (NXDN)] to enter the GID Select mode. Displays SELCALL. SELCALL GID 0001
) or [P3]() to select the desired GID. w e r Push [P2](
Push [PTT] to make a Group call. Push [P1](EXIT). For your reference:
When [Group + SDM (NXDN)] or [Group + Status
(NXDN)] is assigned, you can send a message along with a Group call. w e r To send a Short Data Message with a Group call. q Push [Group + SDM (NXDN)] to enter the GID Se-
lect mode. Displays SELCALL. Push [UP] or [DOWN] to select a desired GID. Push [P1](ENT). Enters the Short Data Message Entry mode. Push [UP] or [DOWN] to enter a character, and then push [P1](SET) to set. Goes to the next character entry position. You can use the 10-keypad keys on the microphone. Repeat step 100 characters. Push [P0](DEL) to delete a character. Push [P2]() or [P3]() left or right to select a charac-
r until you enter a message of up to t ter. SHORT MESSAG y u Push [PTT] to send the message to the selected GID. Push [P1](EXIT) to exit. To send a Status Message with a Group call. q Push [Group + Status (NXDN)] to enter the GID Se-
lect mode. Displays SELCALL. Push [UP] or [DOWN] to select a desired GID. Push [P1](ENT). Enters the Status Message Entry mode. Push [UP] or [DOWN] to select a desired status message. If you want to directly enter a status message, push [P2]
w e r
(MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. You can use the 10-keypad keys on the microphone. STATUS STATUS 001 t y Push [P3](TX) or [PTT] to send the message to the selected GID. Push [P1](EXIT) to exit. 8-3 8 NXDN OPERATION <CONVENTIONAL MODE>
Transmitting a call (Continued) Individual call D You can call a specified station that is set to the same unit ID by using the Individual call function. q Push [Individual (NXDN)] to enter the Unit ID Select mode. Displays SELCALL. SELCALL UID 0001 w Push [UP] or [DOWN] to select a desired unit ID. If you want to directly enter an unit ID, push [P2](MODE) to select the Unit ID Entry mode. e r You can enter an unit ID between 1 and 65519. Push [P3](TX) or [PTT] to make the Individual call. Push [P1](EXIT). For your reference:
When [Individual + SDM (NXDN)] or [Individual + Sta-
tus (NXDN)] is assigned, you can send a message along with an Individual call. D Individual Call Acknowledge Request call When the Individual Call Acknowledge Request func-
tion is set, you can transmit an acknowledgement re-
quest signal with the Individual call. Therefore, you can confirm whether the transceiver is located in the communication range or not. q w e r Push [Individual (NXDN)] to enter the Unit ID Select mode. Displays SELCALL. Push [UP] or [DOWN] to select a desired unit ID. If you want to directly enter an unit ID, push [P2](MODE) to select the Unit ID Entry mode. You can enter an unit ID between 1 and 65519. Push [P3](TX) or [PTT] to make the Individual call with an acknowledgement request signal. Displays CALLING, and then after receiving an acknowl-
edgement, displays HOLDING. When the called station calls back, the transceiver displays the called stations unit ID. Displays NO REPLY and sounds error beeps when your transceiver does not receive an acknowledgement within the preset time period. w e r To send a Short Data Message with an Individual call. Push [Individual + SDM (NXDN)] to enter the unit ID q Select mode. Displays SELCALL. Push [UP] or [DOWN] to select a desired unit ID. Push [P1](ENT). Enters the Short Data Message Entry mode. Push [UP] or [DOWN] to enter a character, and then push [P1](SET) to set. Goes to the next character entry position. You can use the 10-keypad keys on the microphone. Repeat step 100 characters. Push [P0](DEL) to delete a character. Push [P2]() or [P3]() left or right to select a charac-
r until you enter a message of up to t ter. SHORT MESSAG y u Push [PTT] to send the message to the selected unit ID. Push [P1](EXIT) to exit. To send a Status Message with an Individual call. q Push [Individual + Status (NXDN)] to enter the unit ID Select mode. Displays SELCALL. Push [UP] or [DOWN] to select a desired unit ID. Push [P1](ENT). Enters the Status Message Entry mode. Push [UP] or [DOWN] to select a desired status message. If you want to directly enter a status message, push [P2]
w e r
(MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. You can use the 10-keypad keys on the microphone. STATUS STATUS 001 t y Push [P3](TX) or [PTT] to send the message to the selected unit ID. Push [P1](EXIT) to exit. 8-4 8 NXDN OPERATION <CONVENTIONAL MODE>
Transmitting a call (Continued) Status call D The status call is a simple message function to transmit and receive a status message. A transceiver can dis-
play the status message quickly. You cannot transmit a voice signal at the same time. Short Data call D You can send a Short Data message of up to 100 char-
acters. If you turn OFF the transceivers power, the message is cleared. q w Push [Status (NXDN)] to enter the Status Message Select mode. Displays STATUS. Push [UP] or [DOWN] to select a desired status message. If you want to directly enter a status message, push [P2]
(MODE) to select the Status Message Entry mode. You can enter a status message between 1 and 207. You can use the 10-keypad keys on the microphone. STATUS STATUS 001 e Push [P3](TX) or [PTT] to send the selected Status Message. Displays SEND DATA and then COMPLETE. q Push [SDM (NXDN)] to enter the Short Data Mes-
sage Entry mode. Displays MESSAGE?. MESSAGE?
w e Push [UP] or [DOWN] to enter a character, and then push [P1](SET) to set. Goes to the next character entry position. You can use the 10-keypad keys on the microphone. Repeat step 100 characters. Push [P0](DEL) to delete a character. Push [P2]() or [P3]() left or right to select a charac-
w until you enter a message of up to ter. SHORT MESSAG r t Push [PTT] to send. Displays SEND DATA and then COMPLETE. Push [P1](EXIT) to exit. If you exit from the Short Data Message Entry mode, and then you want to transmit the message again, do the following steps. q Push [SDM (NXDN)] to enter the Short Data Mes-
sage Entry mode. Displays the entered message. Displays the last part of the message if the message is over 12 characters. HORT MESSAGE w e Push [PTT] to send. Displays SEND DATA and then COMPLETE. Push [P1](EXIT) to exit. Long Data call D You can send a Long Data message of up to 4,096 characters only by using an external device, such as a PC. You cannot send a message by pushing [PTT]. 8-5 8 NXDN OPERATION <CONVENTIONAL MODE>
Group call Receiving a call D When you receive a Group call that includes a matched GID, your transceiver informs you the calling by sound-
ing beeps and blinking on the function display. In addition, you can easily call back to the calling station. Individual call D When you receive an Individual call that includes your unit ID, your transceiver informs you the calling by sounding beeps and blinking on the function dis-
play. In addition, you can easily call back to the calling station. q When you receive a Group call that includes a matched GID:
Beeps sound. Displays the callers unit ID and GID. blinks for about 10 seconds. q When you receive an Individual call that includes your unit ID:
Beeps sound. Displays the callers unit ID. blinks for about 10 seconds. UID 0001 GID 0002 UID 0001 w To call back to the caller station, push [PTT] while is blinking. To call back to the caller station, push [PTT] while w is blinking. 8-6 8 NXDN OPERATION <CONVENTIONAL MODE>
Receiving a call (Continued) D Individual Call Acknowledge Request call When you receive an Individual Call with an acknowl-
edgement request which includes your own Individual ID, your transceiver automatically transmits a acknowl-
edgement signal, and informs you the calling by beep sounds and bell mark blinks on the function display. In addition, you can easily call back to the calling trans-
ceiver. q When you receive an Individual call with an acknowl-
edgement request signal that includes your unit ID:
Beeps sound. Alternately displays the callers unit ID and INCOMING. To call back to the caller station, push [PTT] while w blinks for about 30 seconds. is blinking. Status call D When you receive a Status call, your transceiver dis-
plays a received status message on the function display. The received message is stored in the Memory Stack, and you can view the message contents in the memory.
(p. 6-3) When you receive a Status call:
Beeps sound. Displays DATA RCVD, COMPLETE, the received mes-
sage, the callers unit ID and GID*.
*Displayed only when the received call is the Group call. The message is stored in the Memory Stack. blinks on the function display. COMPLETE STATUS 001 UID 0001 GID 0002 8-7 Long Data Call D You can receive a Long Data message of up to 4,096 characters. The message can be output to a PC or ex-
ternal device from your transceiver. 8 NXDN OPERATION <CONVENTIONAL MODE>
Receiving a call (Continued) Short Data call D When you receive a Short Data message, your trans-
ceiver displays the message on the function display. The message is also stored in the Memory Stack, and you can view the message in the memory. (p. 6-3) When you receive a Short Data message:
Beeps sound. Displays DATA RCVD, COMPLETE, the received mes-
sage, the callers unit ID and GID*.
*Displayed only when the received call is the Group call. The message is stored in the Memory Stack. blinks on the function display. DATA RCVD COMPLETE SHORT MESSAG Scrolls when the re-
ceived message is over 12 characters. UID 0001 GID 0002 8-8 8 NXDN OPERATION <CONVENTIONAL MODE>
Mixed Mode If you set your transceiver to the Mixed mode, you can receive both digital and analog signals. You can use a digital transceiver on analog channels, therefore you can easy switch from an analog system to a digital sys-
tem. 8-9 A-7148-3EX 2014 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2014-07-16 | 136 ~ 174 | TNB - Licensed Non-Broadcast Station Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2014-07-16
|
||||
1 | Applicant's complete, legal business name |
ICOM Incorporated
|
||||
1 | FCC Registration Number (FRN) |
0005855366
|
||||
1 | Physical Address |
1-1-32 Kamiminami
|
||||
1 |
Osaka, N/A 547-0003
|
|||||
1 |
Japan
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
v******@ultratech-labs.com
|
||||
1 | TCB Scope |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
AFJ
|
||||
1 | Equipment Product Code |
366400
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
A******** T******
|
||||
1 | Title |
General Manager
|
||||
1 | Telephone Number |
+8166********
|
||||
1 | Fax Number |
+8166********
|
||||
1 |
w******@icom.co.jp
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 09/01/2014 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | TNB - Licensed Non-Broadcast Station Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | VHF Digital Transceiver | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power output listed is at the antenna connector. This device must be restricted to work related operations in an occupational/controlled RF exposure environment. The antenna used for this transmitter must not exceed 0 dBi in gain, and is required to be located outside of a vehicle and kept at a distance of 45 cm or more between the transmitting antenna of this device and any persons during operation. The device only transmit when people outside the vehicle are at least the recommended minimum distance of 100 cm away from the properly installed antenna. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
UltraTech Engineering Labs Inc.
|
||||
1 | Name |
T**** L********
|
||||
1 | Telephone Number |
905-8********
|
||||
1 | Fax Number |
905-8********
|
||||
1 |
t******@ultratech-labs.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 22,74,80,9 | EF | 136 | 174 | 50 | 1 ppm | 11K0F3E | |||||||||||||||||||||||||||||||||
1 | 2 | 22,74,80,9 | EF | 136 | 174 | 5 | 1 ppm | 11K0F3E | |||||||||||||||||||||||||||||||||
1 | 3 | 22,74,80,9 | EF | 136 | 174 | 50 | 1 ppm | 8K30F1E | |||||||||||||||||||||||||||||||||
1 | 4 | 22,74,80,9 | EF | 136 | 174 | 5 | 1 ppm | 8K30F1E | |||||||||||||||||||||||||||||||||
1 | 5 | 22,74,80,9 | EF | 136 | 174 | 50 | 1 ppm | 8K30F1D | |||||||||||||||||||||||||||||||||
1 | 6 | 22,74,80,9 | EF | 136 | 174 | 5 | 1 ppm | 8K30F1D | |||||||||||||||||||||||||||||||||
1 | 7 | 22,74,80,9 | EF | 136 | 174 | 50 | 1 ppm | 4K00F1E | |||||||||||||||||||||||||||||||||
1 | 8 | 22,74,80,9 | EF | 136 | 174 | 5 | 1 ppm | 4K00F1E | |||||||||||||||||||||||||||||||||
1 | 9 | 22,74,80,9 | EF | 136 | 174 | 50 | 1 ppm | 4K00F1D | |||||||||||||||||||||||||||||||||
1 | 1 | 22,74,80,9 | EF | 136 | 174 | 5 | 1 ppm | 4K00F1D | |||||||||||||||||||||||||||||||||
1 | 11 | 22,74,8 | EF | 136 | 174 | 50 | 1 ppm | 16K0F3E | |||||||||||||||||||||||||||||||||
1 | 12 | 22,74,8 | EF | 136 | 174 | 5 | 1 ppm | 16K0F3E |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC