OPTIONS 7.2 V DBATTERY PACKS
BP-283 Li-ion BATTERY PACK Voltage:
Capacity: 1910 mAh (minimum), 2010 mAh (typical) Battery life: Approximately 9 hours
(IC-F7010T/IC-F7010S)
BP-284 Li-ion BATTERY PACK Voltage:
Capacity: 3070 mAh (minimum), 3210 mAh (typical) Battery life: Approximately 14 hours*1
*1 When the power save function is set to Short, and the
(IC-F7010T/IC-F7010S) 7.2 V operating periods are calculated under the following conditions:
TX : RX : standby = 5 : 5 : 90 DCHARGERS
BC-219 DESKTOP CHARGER + BC-123S AC ADAPTER For rapidly charging battery packs. Charging time: Approximately 2.8 hours for the BP-283 A power adapter may be supplied, depending on the chargers version.
BC-214 MULTI-CHARGER
+ BC-157S AC ADAPTER, OPC-656 DC POWER CABLE For rapidly charging of up to 6 battery packs simultaneously. Charging time: Approximately 2.8 hours for the BP-283 The AD-132 CHARGER ADAPTER may be needed, depending on The BC-157S AC ADAPTER or OPC-656 DC POWER CABLE must the charger's version. be purchased separately.
BC-225 INTELLIGENT DESKTOP CHARGER + BC-123S AC ADAPTER
+ RS-BC225 READER SOFTWARE For rapidly charging of battery packs. You can check the charging status using the RS-BC225. Charging time: Approximately 2.5 hours for the BP-283 A power adapter may be supplied, depending on the chargers version. An USB (Micro-B) cable is required to connect the BC-225 and a PC with the RS-BC225 installed. DDC CABLES
CP-23L CIGARETTE LIGHTER CABLE Used when charging battery packs through a 12 V cigarette lighter socket. For use with the BC-219.
OPC-515L, OPC-656 DC POWER CABLES Used when charging battery packs using a 13.8 V DC power source instead of the power adapter. OPC-515L: For the BC-219 OPC-656: For the BC-214 FA-S82VS: 150 ~ 162 MHz FA-S81US: 400 ~ 450 MHz DANTENNAS
FA-S81VS, FA-S82VS, FA-S83VS, FA-S81US, FA-S82US STUBBY ANTENNAS Shorter VHF or UHF antennas. FA-S81VS: 136 ~ 150 MHz FA-S83VS: 160 ~ 174 MHz FA-S82US: 450 ~ 490 MHz
FA-S81V, FA-S82V, FA-S83V, FA-S81U, FA-S82U, FA-S83U FLEXIBLE ANTENNAS VHF or UHF antennas. FA-S81V: 136 ~ 150 MHz FA-S83V: 160 ~ 174 MHz FA-S82U: 430 ~ 480 MHz
FA-S67VC, FA-S76UC CUT ANTENNAS FA-S67VC: 136 ~ 174 MHz FA-S76UC: 380 ~ 520 MHz FA-S82V: 148 ~ 160 MHz FA-S81U: 380 ~ 430 MHz FA-S83U: 470 ~ 520 MHz DOTHERS
AD-118 ACC ADAPTER To connect an accessory. See the AD-118 instruction sheet for details of recommended accessories. CAUTION: The AD-118 does not have waterproof protection. When it is connected, NEVER expose the adaptor and the transceiver to rain, snow or any liquids.
LC-184 CARRYING CASE For the Simple key types and Ten-key types.
VS-4MC*2 PTT SWITCH CABLE
+ HS-94, HS-95, HS-97 HEADSET VS-4MC: Used to connect a headset to a transceiver. HS-94: Ear-hook type HS-95: Neck-arm type HS-97: Throat microphone
*2 Non-waterproof.
HM-222 SPEAKER MICROPHONE With an Emergency key. The HM-222 meets IP68 requirements for waterproof protection.
VS-3 Bluetooth HEADSET The Bluetooth headset with a [PTT] switch.
About the third party Bluetooth headsets:
Icom has checked the PTT operation with some 3M Peltor headsets such as the WS Headset XP, WS ProTac XP and WS Alert XP. (Compatibility not guaranteed.) Some options may not be available in some countries. Ask your dealer for details. DBELT CLIPS and BELT HANGERS
MB-133 BELT CLIP
MB-136 BELT CLIP Rotating type.
MB-96F, MB-96FL, MB-96N BELT HANGERS Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incor-
porated (Japan) in Japan, the United States, the United Kingdom, Germa-
ny, France, Spain, Russia, Australia, New Zealand, and/or other countries. The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Icom Inc. is under license. Other trademarks and trade names are those of their respective owners. All other products or brands are registered trademarks or trademarks of their respective holders.
- 4 -
INSTRUCTIONS VHF P25 TRANSCEIVERS I-F7010T/I-F7010S UHF P25 TRANSCEIVERS I-F7020T/I-F7020S IMPORTANT This instruction sheet includes some functions that are usable only when they are preset by your dealer. The transceiver may have other functions and operations that are not described in this instruction sheet. Ask your dealer for preset function details. Thank you for choosing this Icom product. READ ALL INSTRUCTIONS carefully and completely before using this product. SUPPLIED ACCESSORIES Battery pack Belt clip Connector cover
(with a screw)
[Selector]
NOTE: Some accessories are not supplied, or the shape is different, depending on the transceiver version. PANEL DESCRIPTION DAbout the transceiver types There are 2 types of transceivers. IC-F7010S, IC-F7020S: Simple key types IC-F7010T, IC-F7020T: Ten-key types DAbout the Status indicator
Lights blue, then blinks red, yellow, and green when turning ON the transceiver.
Lights red while transmitting.
Lights green while receiving a signal, or when the squelch is open.
Blinks magenta when the battery is exhausted. DAbout the Multi-connector Connects to an optional speaker microphone or headset. CAUTION: DO NOT use the transceiver without the connector cover or the optional equipment attached. The transceiver meets IP68 requirements for dust-tight and waterproof protection only when the connector cover or the optional HM-222 is attached. DAbout the Software key functions NOTE: Your dealers can assign the Software key functions to the keys, keypads, and the Lever switch. Lever Switch
[VOL]
Status indicator Micro-
phone Function Display Multi-
connector
[P1]
[P2]
[Back]
Ten-Key Pad microSD Card Slot Speaker Antenna Connector
[Emer]
[F1]
[PTT]
[OK]
[F2]
[F3]
[Up]/[Down]
[Right]/[Left]
USB
(Micro-B) Connector The illustration is of the Ten-key type transceiver. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-7377H-1EX Printed in Japan 2017 Icom Inc.
- 1 -
FUNCTION DISPLAY q w e Icon Area Text Area Key Display Area NOTE: The screen capture is an example. The displayed position of each icon may differ, depending on the function being used. DIcon Area Indicators q SIGNAL STRENGTH INDICATOR w CLOCK Displays the current time. Displays the relative receive signal strength level. AM or PM is displayed beside the time display when 12 hour display format is selected. e BATTERY INDICATOR Displayed or blinks to indicate the battery status. Indication Battery status Charging required Mid Full Battery exhausted blinks when the battery is exhausted. Icons The following icons are displayed in the Icon Area. POWER ICON
L1 is displayed when the output power is set to Low.
L2 is displayed when the output power is set to Mid.
H is displayed when the output power is set to High. AUDIBLE ICON Displayed when the channel is in the audible (unmute) mode. MESSAGE ICON
Blinks after messages (Message or Status Message) have been received.
Stops blinking when the screen is changed, or any key is pushed, but is displayed if unread messages are still in the Message memory.
Disappears when all messages in the Message memory have been read. BELL ICON Displayed when a matching signal is received, depending on the presetting. SCAN ICON
Displayed when a scan is paused.
Blinks while scanning. SCAN TARGET CHANNEL ICON Displayed when the channel is selected as a scan target channel. SCRAMBLER ICON In the Analog mode:
Displayed when the Voice Scrambler function is ON. GPS ICON
Displayed when valid position data is received.
Blinks when searching for satellites or calculating position data. RECORD ICON
Displayed when the Record function is ON.
Blinks while recording audio. is displayed when there is no microSD card free space and audio cannot be recorded. TALK AROUND ICON Displayed when the Talk Around function is ON. PHONE ICON
Displayed when the transceiver is connected to a telephone network on the selected channel.
Blinks while receiving a phone call. LONE WORKER ICON Displayed when the Lone Worker function is ON. MOTION SENSOR ICON Displayed when the Motion Sensor function is ON. NOISE CANCEL ICON Displayed when the Noise Cancel function is ON. SURVEILLANCE ICON Displayed when the Surveillance function is ON. VIBRATION ICON Displayed when the Vibration function is ON. VOX ICON Displayed when the VOX function is ON. Bluetooth ICON
Displayed when Bluetooth is activated.
Lights Blue when a Bluetooth device is connected.
Does not light when no Bluetooth device is connected. microSD ICON Displayed when a microSD card is inserted into the card slot. is displayed when the microSD card has not been formatted. USB ICON Displayed when a USB device is connected. DText Area Displays the selected Zone number, Channel number, and Channel name, if set. DKey Display Area Displays the names of the function assigned to [P1] and [P2]. Ask your dealer about the assigned Software key functions. BASIC OPERATION Transmitting:
DTurning ON the transceiver NOTE: Before using the transceiver for the rst time, the battery pack must be fully charged for optimum life and operation. See the BATTERY CHARGING section of this sheet. Rotate [VOL] to turn ON the transceiver. DReceiving and Transmitting Receiving:
1. Select a channel.
Rotate [Selector] or push [Up] or [Down], depending on the presetting. When receiving a call, rotate [VOL] to adjust the audio output level to a comfortable listening level. 2. CAUTION: Attach an antenna before transmitting. Transmitting without an antenna may damage the transceiver. 1. Wait until the channel is clear to avoid interference. 2. While holding down [PTT], speak at your normal voice level. 3. Release [PTT] to receive. IMPORTANT:
To maximize the readability of your signal:
1. After pushing [PTT], pause brie y before you start speaking. 2. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak at your normal voice level. BATTERY CHARGING NOTE:
Before detaching or attaching a battery pack, BE SURE to turn OFF the transceiver by rotating [VOL] fully counter clockwise, until it makes a click sound. Otherwise, a transceiver malfunction could occur.
The internal clock will be reset to 00:00 if an exhausted battery is left in the transceiver, or the battery pack is detached, for long periods of time. DRapid charging with the BC-219/BC-225 You can rapidly charge the Li-ion battery pack with the BC-219 or BC-225. To a PC with the RS-BC225 installed.*1 Battery Pack Battery Pack
+ Transceiver Turn OFF Charging time:
BC-219: 2.8 hours for the BP-283 BC-225: 2.5 hours for the BP-283 Additionally needed item (purchase separately):
A power adapter (may be supplied with the charger, depending on the charger version) or the OPC-515L/CP-23L DC POWER CABLES.
A USB cable to connect the PC and BC-225 when using the RS-
BC225. CAUTION: NEVER reverse the polarity when connecting the OPC-515L to a power source. This will ruin the battery charger. White line: +, Black line: _ DRapid charging with the BC-214 You can rapidly charge up to 6 battery packs with the optional BC-214. Charging time:
Approximately 2.8 hours for the BP-283 Additionally needed items (purchase separately):
The BC-157S AC ADAPTER or the OPC-656 DC POWER CABLE
The AD-132 CHARGER ADAPTER (may be supplied with the charger, depending on the charger version) CAUTION: NEVER reverse the polarity when connecting the OPC-656 to a power source. This will ruin the battery charger. Red line: +, Black line: _ Power Adapter*2 The OPC-515L
( for a 13.8 V DC power source) or the CP-23L (for a 12 V cigarette lighter socket) can be used instead of the power adapter.
*1 The RS-BC225 is usable for only with the BC-225.
*2 A different type, or no power adapter is supplied, depending on the charger version. Battery pack
+ Transceiver Turn OFF Battery pack To an AC outlet OPC-656 Connect to a DC power supply:
12 to 16 V, at least 7 A Red line: +
Black line: _ BC-157S BC-214
* Charger adapters shape may differ, depending on the charger version.
- 2 -
- 3 -
FCC INFORMATION
FOR CLASS A UNINTENTIONAL RADIATORS:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAUTION: Changes or modi cations to this transceiver, not expressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations. This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. VOICE CODING TECHNOLOGY The AMBE+2 voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Patent Nos.
#5,870,405, #5,826,222, #5,754,974, #5,701,390,
#5,715,365, #5,649,050, #5,630,011, #5,581,656,
#5,517,511, #5,491,772, #5,247,579, #5,226,084 and
#5,195,166. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand, and/or other countries. AMBE+2 is a trademark and property of Digital Voice Systems Inc. All other products or brands are registered trademarks or trademarks of their respective holders. ABOUT GPS/GLONASS RECEIVER An internal GPS or GLONASS receiver may not work if the transceiver transmits or receives in the frequency ranges as shown below. This problem is made in the internal circuit and does not indicate a transceiver malfunction. For the IC-F7010T/IC-F7010S GPS receiver 142.850 ~ 142.860 157.135 ~ 157.145 146.845 ~ 147.110 Transmit Receive For the IC-F7020T/IC-F7020S GPS receiver Transmit Receive 392.840 ~ 392.865 443.545 ~ 444.065
(Unit: MHz) GLONASS receiver 145.275 ~ 145.945 159.805 ~ 160.540 149.745 ~ 150.790
(Unit: MHz) GLONASS receiver 399.515 ~ 401.343 449.335 ~ 451.425 RECOMMENDATION CLEAN THE TRANSCEIVER THOROUGHLY WITH FRESH WATER after exposure to saltwater, and dry it before operating. Otherwise, the transceiver's keys, switches and controllers may become unusable, due to salt crystallization, and/or the charging terminals of the battery pack may rust. NOTE: If the transceivers waterproof protection appears defective, carefully clean it with a soft, wet (fresh water) cloth, then, dry it before operating. The transceiver may lose its waterproof protection if the case, jack cap, or connector cover is cracked or broken, or the transceiver has been dropped. Icom is not responsible for the destruction or damage to the Icom transceiver, if the malfunction is because of:
Force majeure, including, but not limited to, res, earthquakes, storms, oods, lightning, other natural disasters, disturbances, riots, war, or radioactive contamination.
The use of Icom transceivers with any equipment that is not manufactured or approved by Icom.
- 4 -
PRECAUTIONS VHF P25 TRANSCEIVERS I-F7010T/I-F7010S UHF P25 TRANSCEIVERS I-F7020T/I-F7020S Thank you for choosing this Icom product. READ ALL PRECAUTIONS carefully and completely before using this product. EXPLICIT DEFINITIONS WORD RDANGER!
DEFINITION Personal death, serious injury or an explosion may occur. RWARNING!
Personal injury, re hazard or electric shock may occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No risk of personal injury, re or electric shock. PRECAUTIONS R DANGER! NEVER short terminals of the battery pack. This may damage not only the battery pack, but also the transceiver. R DANGER! NEVER operate the transceiver near unshielded electrical blasting caps or in an explosive atmosphere. R DANGER! Use and charge only speci ed Icom battery packs with Icom transceivers or Icom chargers. Only Icom battery packs are tested and approved for use with Icom transceivers or charged with Icom chargers. Using thirdparty or counterfeit battery packs or chargers may cause smoke, re, or cause the battery to burst. R WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. The continuous high volume operation may cause a ringing in your ears. If you experience the ringing, reduce the volume level or discontinue use. R WARNING! NEVER operate the transceiver while driving a vehicle. Safe driving requires your full attentionanything less may result in an accident. CAUTION: NEVER use harsh solvents such as Benzine or alcohol when cleaning, because they will damage the transceiver surfaces. CAUTION: NEVER carry the transceiver by holding the antenna. CAUTION: CONFIRM the exible antenna, battery pack and jack cover are securely attached to the transceiver, and that the antenna and battery pack are dry before attachment. Exposing the inside of the transceiver to dust or water will result in serious damage to the transceiver.
- 1 -
DO NOT use or place the transceiver in direct sunlight or in places with temperatures below 30C (22F) or above
+60C (+140F). The basic operations of the transceiver are guaranteed within the speci ed operating temperature range. However, the Liquid Crystal Display may not operate correctly, or show an indication in the case of long hours of operation, or after being placed in extremely cold areas. DO NOT modify the transceiver. The speci cations may change and then the transceiver may not comply with the requirements of required regulations. The transceiver warranty does not cover any problems caused by unauthorized modi cation. BE CAREFUL! The trasceiver may become hot when operating it continuously for long periods of time. This may damage the transceiver. BE CAREFUL! The transceiver meets IP68 requirements for dust-tight and waterproof protection. However, once the transceiver has been dropped, dust-tight and waterproof protection cannot be guaranteed because of possible damage to the transceivers case or the waterproof seal. Even when the transceiver power is OFF, a slight current still ows in the circuits. Remove the battery pack from the transceiver when not using it for a long time. Otherwise, the installed battery pack will become exhausted, and will need to be recharged or replaced. ALWAYS turn OFF the transceiver power before connecting any external devices. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-7377H-2EX Printed in Japan 2017 Icom Inc. PRECAUTIONS (continued) SAFETY TRAINING INFORMATION DBattery caution Misuse of Li-ion batteries may result in the following hazards: smoke, re, or the battery may rupture. Misuse can also cause damage to the battery or degradation of battery performance. R DANGER! NEVER solder the battery terminals, or NEVER modify the battery pack. This may cause heat generation, and the battery may burst, emit smoke or catch re. R DANGER! NEVER leave battery pack in places with temperatures above +60C (+140F). High temperature buildup in the battery, such as could occur near res or stoves, inside a sun heated car, or in direct sunlight for long periods of time may cause the battery to rupture or catch re. Excessive temperatures may also degrade battery performance or shorten battery life. R DANGER! DO NOT strike or otherwise impact the battery. Do not use the battery if it has been severely impacted or dropped, or if the battery has been subjected to heavy pressure. Battery damage may not be visible on the outside of the case. Even if the surface of the battery does not show cracks or any other damage, the cells inside the battery may rupture or catch re. R DANGER! DO NOT expose the battery to rain, snow, seawater, or any other liquids. Do not charge or use a wet battery. If the battery gets wet, be sure to wipe it dry before using. R DANGER! KEEP battery packs away from re. Fire or heat may cause them to rupture or explode. Dispose of used battery packs in accordance with local regulations. R DANGER! Use the battery only with the transceiver for which it is speci ed. Never use a battery with any other equipment, or for any purpose that is not speci ed in this instruction manual. R DANGER! If uid from inside the battery gets in your eyes, blindness can result. Rinse your eyes with clean water, without rubbing them, and go to a doctor immediately. R WARNING! NEVER put the battery in a microwave oven, high-pressure container, or in an induction heating cooker. This could cause a re, overheating, or cause the battery to rupture. R WARNING! Immediately stop using the battery if it emits an abnormal odor, heats up, or is discolored or deformed. If any of these conditions occur, contact your Icom dealer or distributor. R WARNING! Immediately wash, using clean water, any part of the body that comes into contact with uid from inside the battery. CAUTION: Always use the battery pack within the speci ed temperature range, for the transceiver, (30C ~ +60C
(22F ~ +140F)), and the battery pack itself (20C ~
+60C (4F ~ +140F)). Using the battery out of its speci ed temperature range will reduce the batterys performance and battery life. Please note that the speci ed temperature range of the battery may exceed that of the transceiver. In such cases, the transceiver may not work properly because it is out of its operating temperature range. CAUTION: Shorter battery life could occur if the battery is left fully charged, completely discharged, or in an excessive temperature environment (above +50C (+122F)) for an extended period of time. If the battery pack must be left unused for a long time, it must be detached from the transceiver after discharging. You may use the battery pack until the remaining capacity is about half, then keep it safely in a cool and dry place at the following temperature range:
20C ~ +50C (4F ~ +122F) (within a month) 20C ~ +40C (4F ~ +104F) (within three months) 20C ~ +20C (4F ~ +68F) BE SURE to replace the battery pack with a new one approximately ve years after manufacturing, even if it still holds a charge. The inside battery material will become weak after a period of time, even with little use. The estimated number of times you can charge the battery is between 300 and 500. Even when the battery appears to be fully charged, the operating time of the transceiver may become short when:
Approximately ve years have passed since the battery was manufactured.
The battery has been repeatedly charged.
(within a year) DCharging caution R DANGER! NEVER charge the battery pack in areas with extremely high temperatures, such as near res or stoves, inside a sun-heated vehicle, or in direct sunlight. In such environments, the safety/protection circuit in the battery will activate, causing the battery to stop charging. R WARNING! NEVER charge the transceiver during a lightning storm. It may result in an electric shock, cause a re or damage the transceiver. Always disconnect the power adapter before a storm. R WARNING! NEVER charge or leave the battery in the battery charger beyond the speci ed time for charging. If the battery is not completely charged by the speci ed time, stop charging and remove the battery from the battery charger. Continuing to charge the battery beyond the speci ed time limit may cause a re, overheating, or the battery may rupture. R WARNING! NEVER insert the transceiver (battery attached to the transceiver) into the charger if it is wet or soiled. This could corrode the battery charger terminals or damage the charger. The charger is not waterproof. NOTE: Charge the battery pack within the speci ed temperature range: BC-214 and BC-219 (+16C ~ +40C
(+60.8F ~ +104F)). Otherwise, the charging time will be longer, but the battery will not reach a full charge. While charging, at a point after the temperature goes out of the speci ed range, the charging will automatically stop. Your Icom radio generates RF electromagnetic energy while transmitting. This radio is designed for and classi ed as for Occupational Use Only. This means it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the General Population in an uncontrolled environment. This radio has been tested and complies with the FCC and IC RF exposure limits for Occupational Use Only. In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans:
W ARNING
FCC KDB Publication 447498 D03, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields.
American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.
American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields RF and Microwave. The antennas, batteries, belt clips, speaker-microphone, and other accessories that are listed in OPTIONS on the INSTRUCTIONS sheet, are authorized for use with this product. Use of accessories other than those speci ed may result in RF exposure levels exceeding the FCC and IC requirements for wireless RF exposure.
Health Canada Safety Code 6 - Limits of Human Exposure to Electromagnetic Energy in the Frequency Range from 3 kHz to 300 GHz. To ensure that your expose to RF electromagnetic energy is within the FCC and IC allowable limits for occupational use, always adhere to the following guidelines:
DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may also cause you to exceed FCC and IC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or an antenna speci cally authorized by the manufacturer for use with this radio. CAU TION DO NOT transmit for more than 50% of the total radio use time (50% duty cycle). Transmitting more than 50% of the time can cause FCC and IC RF exposure compliance requirements to be exceeded. The radio is transmitting when the LED indicator lights red. You can cause the radio to transmit by pushing the PTT switch. ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting, and only use the Icom belt-clips listed in OPTIONS of the INSTRUCTIONS sheet when attaching the radio to your belt, or other place, to ensure FCC and IC RF exposure compliance requirements are not exceeded. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to assure that this radio operates within the FCC and IC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as a consequence of their employment, provided those persons are fully aware of the potential for exposure and can exercise control over their exposure.
- 2 -
- 3 -
INFORMATION FCC POUR LES RAYONNEMENTS NON INTENTIONNELS DE CLASSE A:
Cet quipement a t test et reconnu conforme aux limites fixes pour un appareil numrique de classe A, conformment au point 15 de la rglementation FCC. Ces limites assurent une protection raisonnable contre les interfrences nuisibles lorsque l'quipement est utilis dans un environnement commercial. Cet quipement gnre une nergie de radio frquence, utilise et rayonner et s'il n'est pas install et utilis conformment au manuel d'instruction, peut causer des interfrences nuisibles aux communications radio. Le fonctionnement de cet quipement dans une zone rsidentielle est susceptible de causer des interfrences nuisibles lorsque l'utilisateur doit corriger les interfrences ses propres frais. MISE EN GARDE:
Tout changement ou modification, non expressment ap-
prouv par Icom Inc., peut annuler l'autorisation de l'utili-
sateur utiliser cet appareil conformment la rglemen-
tation FCC. Cet appareil respecte les conditions tablies au paragraphe 15 des rgles de la FCC. Son utilisation est assujettie la condition de ne pas provoquer des interfrences nuisibles. NETTOYEZ ENTIREMENT L'METTEUR-RCEPTEUR AVEC DE L'EAU DOUCE en cas d'exposition l'eau de mer, et le scher avant de l'utiliser. Autrement, les touches de l'metteur-rcepteur, les commutateurs et les contrleurs risquent de devenir inutilisables, cause de la cristallisation du sel, et/ou les bornes de recharge du bloc batterie risquent de rouiller. REMARQUE: Si la protection tanche de l'metteurrcepteur semble dfectueuse, la nettoyer soigneusement avec un tissu mou et humide (d'eau douce), puis la scher avant de l'utiliser. L'metteur-
rcepteur risque de perdre sa protection tanche si le boitier, le capuchon du jack, ou le couvercle du connecteur est fl ou cass, ou en cas de chute de l'metteur-rcepteur. TECHNOLOGIE DE CODAGE DE LA VOIX Le systme de codage AMBE+2 utilis dans ce produit est protg par les rglements de proprit intellectuelle, incluant des droits de proprit, des copyrights et des accords de confidentialit sur les systmes de numrisation de la voix. La licence concernant la technologie de codage de la voix est concde seulement pour tre utilise avec cet quipement de communication. Il est formellement interdit l'utilisateur d'essayer d'extraire, de dcompiler ou de raliser du "reverse engineering" ou tout autre opration ayant pour but de convertir le code objet sous une forme lisible.
#5,870,405, #5,826,222, #5,754,974, #5,701,390,
#5,715,365, #5,649,050, #5,630,011, #5,581,656,
#5,517,511, #5,491,772, #5,247,579, #5,226,084 et
#5,195,166. RCEPTEUR GPS / GLONASS Un GPS interne ou un rcepteur GLONASS peuvent ne pas fonctionner si le l'metteur-rcepteur met ou reoit dans les gammes de frquences comme indiqu ci-dessous. Ce problme est prsent dans le circuit interne et n'indique pas un malfonctionement de l' metteur-rcepteur Pour les IC-F7010T/IC-F7010S Rcepteur GPS 142.850 ~ 142.860 157.135 ~ 157.145 146.845 ~ 147.110 mission Rception
(unite : MHz) Rcepteur GLONASS 145.275 ~ 145.945 159.805 ~ 160.540 149.745 ~ 150.790 Pour les IC-F7020T/IC-F7020S Rcepteur GPS mission Rception 392.840 ~ 392.865 443.545 ~ 444.065
(unite : MHz) Rcepteur GLONASS 399.515 ~ 401.343 449.335 ~ 451.425 Icom, Icom Inc. et le logo Icom sont des marques dposes de Icom Incorporated (Japon) au Japon, aux tats-Unis, au Royaume-
Uni, en Allemagne, en France, en Espagne, en Russie, en Australie, en Nouvelle-Zlande, et/ou dans d'autres pays. AMBE + 2 est une marque dpose et proprit de Digital Voice Systems Inc. Tous les autres produits et toutes les autres marques sont des marques dposes ou non appartenant leur titulaire respectif.
- 4 -
Icom n'est pas responsable de la destruction ou des dommages sur l'metteur-rcepteur Icom, si le dysfonctionnement est caus par:
Force majeure, sans toutefois s'y limiter, les incendies, tremblements de terre, temptes, inondations, la foudre, ou autres catastrophes naturelles, perturbations, meutes, guerre, ou contamination radioactive. L'utilisation de l'metteur-rcepteur Icom avec tout quipement non fabriqu ou approuv par Icom. PRCAUTIONS RADIOS VHF P25 I-F7010T/iF7010S RADIOS UHF P25 I-F7020T/iF7020S Merci davoir choisi un produit Icom. LIRE TOUTES LES PRCAUTIONS soigneuse-
ment et intgralement avant dutiliser la radio. DFINITIONS EXPLICITES DFINITION Risque d'accident mortel, de blessures corporelles graves ou d'explosion. TERME R DANGER!
R AVERTISSEMENT! Risque de blessures corporelles, d'incendie ou de choc lectrique. MISE EN GARDE REMARQUE Risque de dgt matriel. La non prise en compte peut entraner des dsagrments. Absence de risque de blessures corpo-
relles, d'incendie ou de choc lectrique. PRCAUTIONS R DANGER! NE JAMAIS connecter les bornes du pack batterie en court-circuit. R DANGER! NE JAMAIS utiliser la radio prs d'amorces lectriques non blindes ni dans une atmosphre explosive. non blind dtonateur lectrique. R DANGER! Utiliser et charger exclusivement les packs batteries Icom spcifis avec les portatifs Icom ou un chargeurs Icom. Seuls les packs batterie Icom sont tests et homologus pour une utilisation avec les radios Icom ou tre chargs avec les chargeurs Icom. L'utilisation de packs batterie ou de chargeurs tiers ou de contrefaon peut tre l'origine de fumes, d'incendie ou faire clater la batterie. R AVERTISSEMENT! NE JAMAIS utiliser lappareil avec un casque ou dautres accessoires audio rgls sur un niveau sonore lev. Les spcialistes de l'audition mettent en garde contre toute utilisation prolonge niveau sonore lev. Si vous entendez une sonnerie baissez le niveau sonore ou interrompez l'utilisation. R AVERTISSEMENT! NE JAMAIS utiliser la radio en conduisant un vhicule. La scurit de la conduite requiert toute lattention du conducteur toute dfaillance peut tre lorigine dun accident. MISE EN GARDE: NE JAMAIS de nettoyer lappareil avec des produits chimiques telsque lessence ou lalcool susceptibles dendommager la surface de la radio. MISE EN GARDE: NE JAMAIS tenir lmetteur-rcepteur par lantenne pour le transport. MISE EN GARDE: vrifier que l'antenne flexible, batterie et cache de la prise sont solidement fixs la radio, et que l'antenne et la batterie sont secs avant de fixation. Si vous exposez l'intrieur de la radio la poussire ou l'eau, la radio sera remarquablement endommag.
- 1 -
VITER dutiliser ou de laisser la radio en plein soleil ou a une temprature ambiante infrieure a 30C (22F) ou suprieure a
+60C (+140F). Les oprations de base de la radio sont garantis dans la plage de temprature de fonctionnement spcifie. Cependant, l'cran LCD peut ne pas fonctionner correctement aprs avoir t placs dans des zones extrmement froides, ou une icne apparat lors du fonctionnement de la radio pendant une longue priode de temps. NE PAS modifier la radio. Les spcifications peuvent changer et puis ne pas se conformer aux exigences d'un rglement correspondu. La garantie du radio ne couvre pas les problmes rsultant d'une modification non autorise. ATTENTION! La radio chauffe en cas dutilisation continue sur une longue dure. ATTENTION! La radio rpond IP68 exigences de protection tanche la poussire et l'eau. Mais lorsque la radio est tomb vers le bas, tanche la poussire et la protection impermable l'eau ne peuvent pas tre garantis, parce que le cas de la radio ou le joint d'tanchit peuvent tre endommags. Mme lorsque lmetteur-rcepteur est mis hors tension, un courant de trs faible intensit circule dans ses circuits. Retirez la batterie de la radio quand ne pas l'utiliser pendant une longue priode. Sinon, la batterie sera dcharge, et devra tre recharge ou remplace. Assurez-vous de couper l'alimentation de la radio avant de brancher l'quipement fourni ou en option. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-7377H-3US Printed in Japan 2017 Icom Inc. RECOMMENDATION PRCAUTIONS (suite) INFORMATION SUR LA FORMATION LA SCURIT DMise en garde concernant la batterie Un mauvais usage des batteries au Lithium ion peut avoir les consquences suivantes: fume, incendie ou explosion de la batterie. Il peut galement causer des dommages a une autre batterie ou dgrader les performances de la batterie. R DANGER! NE JAMAIS souder les contacts de la batterie NI modifier sa composition. Ceci peut provoquer une surchauffe de la batterie, qui risque alors d'clater, de fumer ou de prendre feu. R DANGER! NE JAMAIS utiliser ni laisser le pack batterie un emplacement o la temprature est suprieure
+60C (+140F). La monte en temprature de la batterie, comme cela peut survenir proximit de flammes ou de poles, l'intrieur d'un vhicule expos au soleil, ou en plein soleil peut dtruire ou enflammer la batterie. Les tempratures excessives peuvent galement dgrader les performances de la batterie ou rduire leur longvit. R DANGER! NE PAS marteler ni cogner la batterie dune quelconque faon. N'utilisez pas la batterie si elle a reu des impacts ou a t jete ou si elle a subi une forte pression. Les dommages subis par une batterie peuvent ne pas tre visibles de l'extrieur du botier. Mme si la surface de la batterie ne semble pas fissure ou endommage, les cellules l'intrieur de la batterie peuvent se rompre ou prendre feu. R DANGER! NE PAS exposer la batterie la pluie, la neige, leau de mer ou tout autre liquide. Ne pas charger ou utiliser une batterie humide. Si une batterie est humide, veillez l'essuyer compltement avant de l'utiliser. R DANGER! Tenir l'cart batteries au feu. Feu ou la chaleur peut provoquer une rupture ou d'exploser. Disposer de batteries utilises conformment la rglementation locale. R DANGER! Utiliser la batterie uniquement avec la radio pour lequel elle est spcifie. Ne jamais utiliser une batterie avec tout autre quipement ou pour une autre destination que celle spcifie dans le prsent manuel d'utilisation. R DANGER! Dans le cas o du liquide provenant de l'intrieur de la batterie entre dans vos yeux, vous risquez la ccit. Rincez abondamment les yeux l'eau courante, sans les frotter et consultez immdiatement un mdecin. R AVERTISSEMENT! NE JAMAIS mettre la batterie dans un four micro-ondes, un rcipient haute-pression ou dans un four induction. Ceci peut provoquer un incendie, une surchauffe ou dtriorer la batterie. R AVERTISSEMENT! Cessez immdiatement d'utiliser la batterie si elle dgage une odeur anormale, si elle surchauffe, est dcolore ou dforme. Si l'une de ces situations se produit, contactez votre revendeur ou distributeur Icom. R AVERTISSEMENT! Lavez immdiatement l'eau courante toute partie du corps qui est entre en contact avec le liquide provenant de l'intrieur de la batterie. MISE EN GARDE: Toujours utiliser la batterie dans la plage de temprature spcifie, comprise entre 30C et +60C
(22F +140F), et de la batterie elle-mme de 20C
+60C (4F +140F). Lutilisation de la batterie hors de la plage de tem prature indique, a pour effet den altrer les performances et den rduire la dure de vie. MISE EN GARDE: La longvit de la batterie peut tre courte si elle est laisse de manire prolonge pleine charge, entirement dcharge, ou dans un environnement temprature excessive (suprieure +50C (+122F)). Si la batterie ne doit pas tre utilise pendant une assez longue priode, elle doit tre enleve de la VHF une fois dcharge. Vous pouvez utiliser la batterie jusqu' ce que le tmoin de la batterie indique qu'elle est la moiti de sa capacit. Placez-la ensuite dans un endroit frais et sec dans la plage de temprature ci-aprs :
20C ~ +50C (4F ~ +122F) (priode infrieure un mois) 20C ~ +40C (4F ~ +104F) (priode infrieure trois mois) 20C ~ +20C (4F ~ +68F)
(priode infrieure une anne) VEILLEZ remplacer la batterie par une nouvelle aprs cinq ans, mme si elle maintient la charge. Les matriaux prsents l'intrieur de la batterie se dtriorent aprs un certain temps, mme en cas d'utilisation rduite. Le nombre de fois o il est possible de charger la batterie est estim entre 300 et 500 fois en fonction de l'utilisation. Mme lorsque la batterie indique qu'elle est compltement charge, le temps d'utilisation du poste peut tre rduit dans les cas suivants:
Sono passati approssimativamente cinque anni dalla data di fabbrica della batteria. La batteria stata ripetutamente caricata. DMise en garde concernant la recharge R DANGER! NE JAMAIS charger le pack batterie des endroits exposs des tempratures extrmement leves, comme proximit de flammes ou de poles, l'intrieur d'un vhicule expos au soleil, ou en plein soleil. Dans ces environnements, le circuit de scurit/protection l'intrieur de la batterie peut s'activer et interrompre la recharge de la batterie. R AVERTISSEMENT! NE JAMAIS charger l'metteur-
rcepteur durant un orage. Cela risquerait de provoquer un choc lectrique, un incendie ou d'endommager l'metteur-
rcepteur. Toujours dbrancher l'adaptateur de courant avant une tempte. R AVERTISSEMENT! NE JAMAIS charger ou laisser la batterie dans le chargeur de batterie au-del de la dure de charge indique. Si la batterie n'est pas compltement charge pendant le temps spcifi, interrompez la recharge et retirez la batterie du chargeur de batterie. La poursuite de la charge au-del de dure indique peut provoquer un incendie, une surchauffe ou lclatement de la batterie. R AVERTISSEMENT! NE JAMAIS insrer un metteur-
rcepteur humide ou poussireux (avec sa batterie) dans le chargeur. Ceci peut corroder les bornes du chargeur de la batterie ou endommager le chargeur. Le chargeur n'est pas tanche. REMARQUE: Charger la batterie l'intrieur de la plage de tempratures spcifie de +16C +40C (+60.8F
+104F): BC-214/ BC-219. Sinon, le temps de charge sera plus long, mais la batterie ne sera pas atteindre une charge complte. La charge s'arrte automatiquement lorsque la temprature est hors de la plage spcifie. Votre radio Icom produit une nergie lectromagntique de radiofrquences (RF), en mode de transmis-
sion. Cette radio est conue pour un usage professionnel seulement et classe comme tel, ce qui signifie quelle doit tre utilise uniquement dans le cadre dun travail par des personnes conscientes des dangers et des mesures visant minimiser ces dangers. Elle NEST PAS conue pour une utilisation grand pu-
blic, dans un environnement non contrl. Cet appareil a t valu et jug conforme, aux limites dexposition aux RF de la FCC et dIC, pour une utilisation grand public. En outre, votre radio Icom satisfait les normes et directives qui suivent en ma-
tire de niveaux dnergie et dnergie lectromagntique de RF et dvaluation de tels niveaux en ce qui concerne lexposition humaine:
Publication 447498 D03 de la FCC KDB, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Fre-
quency Electromagnetic Fields. Norme de lAmerican National Standards Institute (ANSI): IEEE C95.1-1992 sur les niveaux de scurit compatibles avec lexposition humaine aux champs lectromagntiques de radiofrquences (3 kHz 300 GHz). Norme de lANSI: IEEE C95.3-1992 sur la mthode dvaluation recommande du champ magntique potentiellement dange-
reux des radiofrquences et des micro-ondes. Les accessoires illustrs dans Options de la feuille d'instructions sont approuvs pour une utilisation avec ce produit. Lutili-
sation daccessoires autres que ceux prciss peut entraner des niveaux dexposition aux RF suprieures aux limites tablies par la FCC et dIC en matire dexposition aux RF sans fil. Le Code de scurit 6 de Sant Canada - Les limites dexposition humaine lnergie lectromagntique dans la gamme de frquences de 3 kHz 300 GHz. Afin de vous assurer que votre exposition une nergie lectromagntique de RF se situe dans les limites permises par la FCC et dIC pour une utilisation grand public, veuillez en tout temps respecter les directives suivantes:
NE PAS faire fonctionner la radio sans quune antenne approprie y soit fixe, car ceci risque dendom-
mager la radio et causer une exposition suprieure aux limites tablies par la FCC et dIC. Lantenne ap-
proprie est celle qui est fournie avec cette radio par le fabricant ou une antenne spcialement autorise par le fabricant pour tre utilise avec cette radio. NE PAS mettre pendant plus de 50 % du temps total dutilisation de lappareil (50 % du facteur dutilisation). La notion 50%
du facteur dutilisation sapplique galement au mode VOX/PTT. mettre pendant plus de 50 % du temps total dutilisation peut causer une exposition aux RF suprieure aux limites tablies par la FCC et dIC. Lorsque le voyant DEL rouge sallume, cette radio est en train dmettre. La radio mettra si vous appuyez sur le bouton du microphone. TOUJOURS tenir lantenne loigne dau moins 2,5 cm de votre corps au moment dmettre et utiliser uniquement lattache pour ceinture Icom illustre dans Options de la feuille d'instructions, lorsque vous attachez la radio votre ceinture, ou autre chose, de faon vous assurer de ne pas provoquer une exposition aux RF suprieure aux limites fixes par la FCC et dIC. Pour offrir vos interlocuteurs la meilleure qualit de transmission possible, tenez lantenne au moins 5 cm de votre bouche et lgrement de ct. Les renseignements ci-dessus fournissent lutilisateur toute linformation ncessaire sur lexposition aux RF et sur ce quil faut faire pour assurer que cette radio fonctionne en respectant les limites dexposition aux RF tablies par la FCC et dIC. Interfrence lectromagntique et compatibilit En mode de transmission, votre radio Icom produit de lnergie de RF qui peut provoquer des interfrences avec dautres appa-
reils ou systmes. Pour viter de telles interfrences, mettez la radio hors tension dans les secteurs o une signalisation lexige. NE PAS faire fonctionner lmetteur dans des secteurs sensibles au rayonnement lectromagntique tels que les hpitaux, les aronefs et les sites de dynamitage. Usage professionnel/contrl Ce radio metteur est utilis dans des cas o des personnes sont exposes en raison de leur travail, pourvu quelles soient conscientes du risque dexposition et quelles puissent exercer un contrle sur cette exposition.
- 2 -
- 3 -