IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page a (1,1) INSTRUCTION MANUAL VHF TRANSCEIVER iF111S iF121S UHF TRANSCEIVER iF211S iF221S IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page i (1,1) IMPORTANT PRECAUTION READ ALL INSTRUCTIONS carefully and com-
pletely before using the transceiver. SAVE THIS INSTRUCTION MANUAL This instruction manual contains important operating instructions for the IC-F111S/F121S VHF TRANSCEIVER and IC-
F211S/F221S UHF TRANSCEIVER. EXPLICIT DEFINITIONS WORD RWARNING CAUTION NOTE DEFINITION Personal injury, re hazard or electric shock may occur. Equipment damage may occur. If disregarded, inconvenience only. No risk of personal injury, re or electric shock. Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United states, the United Kingdom, Germany, France, Spain, Russia and/or other coun-
tries. SmarTrunk II is a Trademark of SmarTrunk Systems, Inc. i RWARNING! NEVER connect the transceiver to an AC outlet. This may pose a re hazard or result in an electric shock. CAUTION! NEVER touch the transceiver (especially the heat sink) when transmitting continuously for long peri-
ods. It will become hot. NEVER connect the transceiver to a power source of more than 16 V DC such as a 24 V battery. This connection will ruin the transceiver. NEVER cut the DC power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting, the transceiver might be damaged. NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury. NEVER allow children to touch the transceiver. NEVER expose the transceiver to rain, snow or any liquids. IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page ii (1,1) USE the supplied microphone only. Other microphones have different pin assignments and may damage the trans-
ceiver. DO NOT use or place the transceiver in areas with tempera-
tures below 22F (30C) or above +140F (+60C), or in areas subject to direct sunlight, such as the dashboard of a vehicle. AVOID operating the transceiver without running the vehi-
cles engine. The vehicles battery will quickly run out if the transceiver is in transmission while the vehicles engine OFF. AVOID placing the transceiver in excessively dusty envi-
ronments. AVOID placing the transceiver against walls. This will obstruct heat dissipation. AVOID the use of chemical agents such as benzine or alco-
hol when cleaning, as they damage the transceiver surfaces. For U.S.A. only CAUTION: Changes or modifications to this transceiver, not ex-
pressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations. TABLE OF CONTENTS IMPORTANT .................................................................................... i EXPLICIT DEFINITIONS ................................................................. i PRECAUTION .................................................................................. i TABLE OF CONTENTS .................................................................. ii 1 PANEL DESCRIPTION ........................................................... 15 I Front panel ............................................................................... 1 I Function LED ........................................................................... 2 I Programmable function keys .................................................... 3 2 OPERATION ............................................................................ 68 I Turning power ON .................................................................... 6 I Channel selection ..................................................................... 6 I Receiving and transmitting ....................................................... 7 D Transmitting notes ................................................................. 7 D Scrambler function ................................................................ 8 D User set mode ....................................................................... 8 3 CONNECTION AND MAINTENANCE .................................. 913 I Rear panel and connection ...................................................... 9 I Supplied Accessories ............................................................. 10 I Mounting the transceiver ......................................................... 11 I Optional UT-108 installation ................................................... 11 I Optional UT-109/UT-110 installation ...................................... 12 I Optional OPC-617 installation................................................. 12 I Antenna ................................................................................... 13 I Fuse replacement .................................................................. 13 I Cleaning ................................................................................. 13 4 OPTIONS ................................................................................... 14 5 SAFETY TRAINING INFORMATION ........................................ 15 ii IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page 1 (1,1) 1 PANEL DESCRIPTION I Front panel q Function LED (p. 2) 1 2 3 4 TX/RX w e r q AF VOLUME CONTROL KNOB Rotate the knob to adjust the audio output level. Minimum audio level is pre-programmed. e DEALER-PROGRAMMABLE KEYS [P0] to [P3]
Desired functions can be programmed independently by your Dealer. w MICROPHONE CONNECTOR Connect the supplied microphone or optional DTMF micro-
r POWER SWITCH [POWER]
Push to turn the power ON and OFF. phone. NEVER connect non-specified microphones. The pin assignments may be different and the transceiver may be damaged. The following functions are available at power ON as options:
- Automatic scan start
- Password prompt
- Set mode 1 IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page 2 (1,1) PANEL DESCRIPTION 1 DD MICROPHONE The supplied microphone has a PTT switch and a hanger hook. The following functions are available when the microphone is on or off hook:
- Automatic scan start when hook on.
- Automatic priority channel selection when hook off.
- Sets to Inaudible condition (mute condition) when hook on.
- Sets to Audible condition (unmute condition) when hook off. I Function LED 1 q 2 e 3 4 TX/RX w q CHANNEL INDICATORS Indicates the operating channel. Blinks when receiving a signal during scanning opera-
tion. All LEDs blink while entering the power ON password. w TX/RX INDICATOR Lights red: while transmitting Lights green: while the channel is busy Blinks orange (green and red blink simultaneously):
when the specied 2-tone, 5-tone call is received. Green and red blink alternately: cloning error e ACTIVATED KEY INDICATOR (LP 0/1/2) Appears when a pre-programmed key function is acti-
vated. NOTE: When all function LEDs blink, check the DC battery voltage is not too high. 2 IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page 3 (1,1) 1 PANEL DESCRIPTION I Programmable function keys The following functions can be assigned to [P0], [P1], [P2]
and [P3] programmable function keys. Consult your Icom Dealer or System operator for details con-
cerning your transceivers programming. In the following explanations, programmable function names are bracketed. The specic switch used to activate the func-
tion depends on programming. SCAN TAG KEY TAG Adds or deletes the selected channel to the scan group. PRIORITY CHANNEL KEYS PRI A PRI B Push these keys to select priority A or priority B channel, respectively. CH UP AND DOWN KEYS OPERATING CHANNEL KEYS Select an operating channel. CH UP CH DN BANK KEY BANK Select and determine a bank number. CH1 CH2 CH3 CH4 Select an operating channel directly. SCAN START/STOP KEY SCAN A SCAN B Push this key to start scanning; and push again to stop. NOTE: Place the microphone on hook to start scanning. Take the microphone off hook to stop scanning. 3 LOCK KEY LOCK Push this key for 1 sec. to lock all programmable keys except the following:
[CALL] (incl. [CAL A] and [CAL B]), [MONI]
and [EMER] keys. IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page 4 (1,1) PANEL DESCRIPTION 1 MONITOR KEY TALK AROUND KEY MONI Activates one of (or two of) the following functions on each channel independently:
Push and hold the key to unmute the channel (audio is emitted; Audible condition). Push the key to toggle the mute and unmute condi-
tions (toggles Audible and Inaudible). Push the key to mute the channel (sets to Inaudible only). Push the key to unmute the channel (sets to Audible TA Turns the talk around function ON and OFF. The talk around function equalizes the transmit frequency to the receive frequency for mobile-to-
mobile communication. WIDE/NARROW KEY W/N Push this key to toggle the bandwidth between wide or narrow. only). DTMF AUTODIAL KEY Push the key after communication is nished to send a DTMF Push this key to transmit a specied DTMF code. reset code. NOTE: The unmute condition (Audible condi-
tion) may automatically return to the mute con-
dition (Inaudible condition) after a specified period depending on the pre-setting. OUTPUT POWER SELECTION KEYS H/L Select the transmit output power temporarily, or permanently, depending on the pre-setting. Ask your Dealer or System Operator for the out-
put power level for each selection. CALL KEY CALL CAL A CAL B Transmit a 2-tone, 5-tone code. Call transmission is necessary before you call another station depending on your signaling sys-
tem. The [CAL A] and/or [CAL B] keys may be avail-
able when your system employs selective Individual/Group calls. Ask your Dealer which call is assigned to each key. 4 IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page 5 (1,1) 1 PANEL DESCRIPTION EMERGENCY KEY SCRAMBLER KEY EMER Push and hold the key to transmit an emergency call. If you want to cancel the emergency call, push and hold (or push) the key again before trans-
mitting the call. Depending on the pre-setting, the emergency call is transmitted one time only, or repeatedly, until receiving a control code. Hook Scan HOOK Several functions are available for the hanger function when taking the microphone from its hanger (hanger-off) and/or returning it to the hanger (hanger-on). USER SET MODE KEY SET Changes the contents of the items in the User Set mode. Please refer to p. 8. Push and hold this key for 1 sec. to enter set mode. Push this key again momentarily to select the desired item. Push [P2] and [P3] to set the desired level/condition. Push and hold this key again to exit set mode. User set mode also available via the Power ON function. 5 SCRM Push and hold to turn the voice scrambler func-
tion ON. Push this key to turn the voice scrambler func-
tion OFF. NOTE:
The optional UT-109 (#02) or UT-110 (#02) VOICE SCRAMBLER UNIT is required. UT-109: Non-rolling type. 32 codes are available. UT-110: Rolling type. Provides higher communi-
cation security. 1020 (4 groups 255) codes are available. This transceiver requires version #02 of these units. Do not install version #01, as they are not compatible. Some PC board modifications are required when installing UT-109 and UT-110. Please refer to Optional UT-109/UT-110 installation.
(p.12) Please contact your Dealer for details. IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page 6 (1,1) I Turning power ON q Push [
] to turn the power ON. w If the transceiver is programmed for a start up passcode, input the digit codes as directed by your Dealer. The keys in the table below can be used for password input:
The transceiver detects numbers in the same block as identical. Therefore 01234 and 56789 are same. e When all channel indicator LEDs still blink after inputting 4 digits, the input code number is incorrect. Turn the power off and start over in this case. KEY NUMBER 0 5 1 6 2 7 3 8 4 9 OPERATION 2 I Channel selection Several types of channel selection are available. The meth-
ods may differ according to your system setup. NON-BANK TYPE:
Push [CH UP]/[CH DN] to select the desired operating chan-
nel, in sequence; or, push one of the [CH 1] to [CH 4] keys to select a channel directly. BANK-TYPE:
Push [BANK] to toggle between bank 1 and 2. AUTOMATIC SCAN TYPE:
Channel setting is not necessary for this type. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call or when taking the microphone off hook. 6 IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page 7 (1,1) 2 OPERATION I Receiving and transmitting RECEIVING:
q Push [POWER] to turn the power ON. w Push [CH UP] or [CH DN] to select a channel. e When receiving a call, adjust the audio output level to a comfortable listening level. TRANSMITTING:
r Take the microphone off hook. The channel is busy when TX/RX indicator turns green.
- According to the trasceivers setting;
2-tone, 5-tone mute may be released. (The audible condition is selected) A priority channel may be selected automatically. t Wait for the channel to become clear. y Push the [CALL] key when initiating a call from your side.
- According to the trasceivers setting;
Coded audio may be heard from the transceiver, then TX/RX indicator turns green. This operation may not be necessary depending on your signal-
ing system. Ask your Dealer. u While pushing and holding [PTT], speak into the micro-
phone at your normal voice level. i Release [PTT] to receive. IMPORTANT: To maximize the readability of your signal:
(1) Pause briey after pushing [PTT]
(2) Hold the microphone 2 to 5 cm from your mouth, then speak into the microphone at a normal voice level. D Transmitting notes Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions:
The channel is in mute condition. Channel is busy. A matched/non-matched CTCSS code is received. The selected channel is a receive only channel. Time-out timer After continuous transmission for a pre-programmed period, the time-out timer is activated causing the transceiver to stop transmitting and automatically select receive. Penalty timer Once the time-out timer is activated, transmission is further inhibited for a period determined by the penalty timer. 7 IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page 8 (1,1) OPERATION 2 eThen push [P2] and [P3] to set the desired level/condition. rPush [POWER] (or push and hold [P0]) again to exit set mode. User set mode is also available via a programmable key. Please refer to p. 5 [SET] section. D Scrambler function The UT-109 (#02) or UT-110 (#02) optional voice scrambler unit provides high performance private communication between stations with the same scrambler codes. q Push and hold [SCRM] to turn the scrambler function ON. w Push [SCRM] to turn the function OFF. D User set mode User set mode is accessed at power ON and allows you to set seldom-changed settings. In this case you can cus-
tomize transceiver operation to suit your preferences and operating style. Entering the user set mode:
qWhile pushing and holding [P1] and [P2], push [POWER] to enter user set mode at power ON. wPush and hold [P0] to enter user set mode. Push [P0]
again momentarily to select the item. The channel indicator lights respectively to indicate the function is selected. Available set mode functions;
Backlight (
Beep (
SQL Level (
3 AF Min level (
: OFF, Dim, Auto or ON
: OFF or ON
: 0 to 255
: 0 to 255 lights) 4 lights) lights) lights) 2 1 8 IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page 9 (1,1) 3 CONNECTION AND MAINTENANCE I Rear panel and connection w q Antenna Optional speaker
(SP-22) R CAUTION! NEVER re-
move the fuse-holder from the DC power cable. black:
red:
12V Battery NEVER connect to a 24 V battery. NOTE: Use the terminals as shown below for the cable connections. Crimp Solder To the antenna connector t Optional cable
(OPC-617) e r 9 IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page 10 (1,1) q ANTENNA CONNECTOR Connects to an antenna. Ask your Dealer about antenna selection and placement. w MICROPHONE HANGER Connect the supplied microphone hanger to the vehicles ground for microphone on/off hook functions. (See p. 1) e DC POWER RECEPTACLE Connects to a 12 V DC battery. Pay attention to polarities. NEVER connect to a 24 V battery. This could damage the transceiver. r OPTIONAL CABLE (OPC-617) Connect an external modem unit, Dimmer control, etc. t EXTERNAL SPEAKER JACK Connect a 48 external speaker, if desired. CONNECTION AND MAINTENANCE 3 I Supplied Accessories q M O I C y w e r t KEY-STICKER u i o
!0
!1
!2 q Microphone ...................... 1 w Microphone hanger and screw set ..................... 1 set e Microphone hanger cable . 1 r DC power cable (OPC-1132)
............................................1 t Function name stickers*
(KEY STICKER) ....................1 y Mounting bracket .............. 1 u Bracket bolts ..................... 4 i Mounting screws (M512) . 4 o Self-tapping screws (M520)
........................................... 4
!0 Flat washers ...................... 4
!1 Spring washers ................. 4
!2 Nuts ................................... 4
*Function name stickers There are no names on the programmable function keys since the functions can be freely assigned to these keys. Attach the supplied function name stickers above the appropriate keys for easy recognition of that keys assigned function. 10 IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page 11 (1,1) 3 CONNECTION AND MAINTENANCE I Mounting the transceiver The universal mounting bracket supplied with your transceiv-
er allows overhead mounting. Mount the transceiver securely with the 4 supplied screws to a thick surface which can support more than 1.5 kg. Flat washer Spring washer When using self-tapping screws 11 I Optional UT-108 installation Install the optional UT-108 DTMF decoder unit as follows:
q Turn the power OFF, then disconnect the DC power cable. w Unscrew the 4 screws, then remove the bottom cover. e Install the unit as shown in the diagram below. r Replace the bottom cover and screws, then re-connect the DC power cable. UT-108 Front panel IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page 12 (1,1) I Optional UT-109 /UT-110 installation q Turn the power OFF, then disconnect the DC power cable. w Unscrew the 4 screws, then remove the bottom cover. e Cut the pattern on the PCB at the TX mic circuit (MIC) and RX AF circuit (DISC) as shown below. r Install the scrambler unit as described in optional UT-108 installation in the page at left. t Return the bottom cover and screws to the original posi-
tion. Front panel DISC MIC NOTE: Be sure to re-solder the above disconnected points when you remove the scrambler units. Otherwise no TX modulation or AF output is available. CONNECTION AND MAINTENANCE 3 I Optional OPC-617 installation Install the OPC-617 as shown below. OPC-617 Cut off the bushing as in the illustra-
tion, when you install the optional OPC-617. OPTIONAL CABLE PIN ASSIGNMENT t r e w q o i u y q Dimmer cont. IN or IGSW cont. IN w AF OUT e Det. AF OUT r Mod. IN t PTT control IN or FTSW control IN y Horn drive cont. OUT u AF GND i Det. AF GND o Mod. GND 12 IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page 13 (1,1) 3 CONNECTION AND MAINTENANCE I Antenna A key element in the performance of any communication sys-
tem is an antenna. Ask your Dealer about antennas and the best places to mount them. I Fuse replacement A fuse is installed in the supplied DC power cable. If a fuse blows or the transceiver stops functioning, track down the source of the problem, if possible, and replace the damaged fuse with a new rated one. Fuse rating: 20 A, IC-F520/F620: 20 A I Cleaning If the transceiver becomes dusty or dirty, wipe it clean with a soft, dry cloth. AVOID the use of solvents such as benzene or alcohol, as they may damage the transceiver sur-
faces. 13 IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page 14 (1,1) OPTIONS 4 SP-22 EXTERNAL SPEAKER Compact and easy-to-install. Input impedance : 4 Max. input power : 5 W HM-100TN DTMF microphone. SM-25 Desktop microphone. UT-108 DTMF DECODER UNIT Provides pager and code squelch capabilities. UT-109/UT-110 (#02) VOICE SCRAMBLER UNIT UT-109 : Non-rolling type (max. 32 codes) UT-110 : Rolling type (max. 1020 codes) OPC-617 ACC CABLE Allows you to connect to an external terminal. 14 IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page 15 (1,1) 5 SAFETY TRAINING INFORMATION Your Icom radio generates RF electromag-
netic energy during transmit mode. This radio is designed for and classified as Occupational Use Only, meaning it must be used only during the course of employ-
ment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the General Population in an uncontrolled environment. W ARNING For compliance with FCC and Industry Canada RF Exposure Requirements, the transmitter antenna installation shall comply with the following two conditions:
1. The transmitter antenna gain shall not exceed 0 dBi. 2. IC-F121S:
The transmitter antenna is required to be located outside of a vehicle and kept at a separation distance of 65 cen-
timeters or more between the transmitter antenna of this device and persons during operation. 3. IC-F221S:
The transmitter antenna is required to be located outside of a vehicle and kept at a separation distance of 52 cen-
timeters or more between the transmitter antenna of this device and persons during operation. To ensure that your exposure to RF elec-
tromagnetic energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines:
CAU TION DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or an antenna specically authorized by the manufacturer for use with this radio. DO NOT transmit for more than 50% of total radio use time
(50% duty cycle). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the TX indica-
tor lights red. You can cause the radio to transmit by press-
ing the PTT switch. Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radi-
ation such as hospitals, aircraft, and blasting sites. 15 IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page 16 (1,1) MEMO IC-F111S/F121S_F211S/F221S 02.9.6 0:58 PM Page Z (1,1) Count on us!
A-6199H-1EX Printed in Japan 2002 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan