all | frequencies |
|
|
exhibits | applications |
---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual 1 | Users Manual | 2.48 MiB | ||||
1 |
|
User Manual 2 | Users Manual | 1.61 MiB | ||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | Test Report | |||||||
1 | External Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | Attestation Statements | |||||||
1 | Operational Description | |||||||
1 | Attestation Statements | |||||||
1 | Test Setup Photos | |||||||
1 | Parts List/Tune Up Info |
1 | User Manual 1 | Users Manual | 2.48 MiB |
INSTRUCTION MANUAL VHF TRANSCEIVER iV80 iV80E This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE C E L L U L A R R A D I OT E L E P H O N E S E RV I C E S I G N A L S I S PROHIBITED UNDER FCC RULES AND FEDERAL LAW. FOREWORD Thank you for purchasing this fine Icom product. The IC-V80/
V80E vhf transceiver is designed and build with Icoms superior technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. We want to take a couple of moments of your time to thank you for making your IC-V80/V80E your radio of choice, and hope you agree with Icoms philosophy of technology first. Many hours of research and development went into the design of your IC-V80/V80E. FEATURES D u s t - p r o t e c t i o n / S p l a s h - r e s i s t a n t construction (IP54*)
* Only when the battery pack/case, antenna and jack cover are attached. Built in VOX circuit enabling the VOX operation* (voice operated transmission)
* To use the VOX operation, an optional headset and a plug adapter cable are additionally required. i EXPLICIT DEFINITIONS DEFINITION WORD R DANGER!
R WARNING!
CAUTION NOTE Personal death, serious injury or an ex-
plosion may occur. Personal injury, fire hazard or electric shock may occur. Equipment damage may occur. Recommended for optimum use. No risk of personal injury, fire or electric shock. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL This instruction manual contains important operating instructions for the IC-V80/V80E. PRECAUTIONS RWARNING RF EXPOSURE! This device emits Radio Frequency (RF) energy. Caution should be observed when operating this device. If you have any questions re-
garding RF exposure and safety standards, please refer to the Federal Communications Commission Office of Engi-
neering and Technologys report on Evaluating Compliance with FCC Guidelines for Human Radio Frequency Electro-
magnetic Fields (OET Bulletin 65) RWARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm
(2 to 4 inches) away from the lips and the transceiver is ver-
tical. RWARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. Hearing experts advise against continuous high volume op-
eration. If you experience a ringing in your ears, reduce the volume level or discontinue use. RWARNING! NEVER operate the transceiver while driving a vehicle. Safe driving requires your full attention anything less may result in an accident. NEVER connect the transceiver to a power source using reverse polarity. This will ruin the transceiver. DO NOT operate the transceiver near unshielded electri-
cal blasting caps or in an explosive atmosphere. DO NOT push [PTT] unless you actually intend to trans-
mit. BE CAREFUL! The transceiver will become hot when operating it continuously for long periods. DO NOT use or place the transceiver in direct sunlight or in areas with temperatures below 20C (4F) or above
+60C (+140F). Place the unit in a secure place to avoid inadvertent use by children. DO NOT use harsh solvents such as benzene or alco-
hol to clean the transceiver, because they can damage the transceivers surfaces. ii PRECAUTIONS KEEP the transceiver away from heavy rain, and never immerse in the water. The transceiver meets IP54* require-
ments for dust-protection and splash resistance. However, once the transceiver has been dropped, dust-protection and splash resistance cannot be guaranteed because of possible damage to the transceivers case or the waterproof seal.
* Only when the battery pack/case, antenna and jack cover are at-
tached. NEVER operate or touch the transceiver with wet hands. This may result in an electric shock or may damage the transceiver. Even when the transceiver power is OFF, a slight current still flows in the circuits. Remove the battery pack or batteries from the transceiver when not using it for a long time. Oth-
erwise, the installed battery pack or batteries will become exhausted, and will need to be recharged or replaced. Approved Icom optional equipment is designed for optimal performance when used with an Icom transceiver. Icom is not responsible for the destruction or damage to an Icom transceiver in the event the Icom transceiver is used with equipment that is not manufactured or approved by Icom. FCC INFORMATION FOR CLASS B UNINTENTIONAL RADIATORS:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment generates, uses and can radi-
ate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular in-
stallation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and re-
ceiver. Connect the equipment into an outlet on a circuit differ-
ent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV techni-
cian for help. CAUTION: Changes or modifications to this device, not expressly approved by Icom Inc., could void your authority to operate this device under FCC regulations. iii SUPPLIED ACCESSORIES The following accessories are supplied with the transceiver. Battery pack*
Antenna Jack cover
(with screws) Belt clip*
Battery charger*
AC adapter*
* Not supplied, or the shape is different, depending on the version. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. Microsoft, Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United States and/or other countries. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 iv TABLE OF CONTENTS FOREWORD ..................................................................................... i FEATURES ........................................................................................ i EXPLICIT DEFINITIONS ................................................................... i IMPORTANT ...................................................................................... i PRECAUTIONS ............................................................................iiiii FCC INFORMATION ....................................................................... iii SUPPLIED ACCESSORIES ............................................................ iv TABLE OF CONTENTS ............................................................... vvi 1 ACCESSORIES ...........................................................12 Antenna ...................................................................................1 Belt clip ....................................................................................1 Battery pack/case ....................................................................2 Jack cover ................................................................................2 2 PANEL DESCRIPTION ................................................37 Front, top and side panels .......................................................3 Function display .......................................................................6 3 BATTERY CHARGING ..............................................813 Caution (for the BP-264 Ni-MH battery) ................................... 8 Caution (for the BP-265 Li-Ion battery) ....................................9 Battery chargers ....................................................................11 Battery case (BP-263) ............................................................... 13 Battery information ................................................................13 4 BASIC OPERATION ................................................1419 Power ON ..............................................................................14 Adjusting the volume level .....................................................14 Adjusting the squelch level ....................................................14 v Monitor function .....................................................................14 Mode selection.......................................................................15 Operating mode selection ......................................................16 Setting a tuning step ..............................................................16 Setting a frequency ................................................................16 Receiving ...............................................................................17 Transmitting ............................................................................17 Key lock function ....................................................................18
[VOL] function assignment .....................................................18 Weather channel operation (U.S.A. version only) ..................19 5 REPEATER AND DUPLEX OPERATION ...............2023 Repeater operation ................................................................20 Duplex operation ....................................................................21 Subaudible tones ...................................................................22 Lockout function .....................................................................23 Auto repeater function (U.S.A. version only) .........................23 6 MEMORY/CALL OPERATION ................................2428 General description................................................................24 Selecting a memory channel .................................................24 Selecting the Call channel .....................................................24 Channel programming ...........................................................25 Copying memory/Call contents ..............................................26 Clearing memory contents .............................................................27 Display type ...........................................................................27 Programming a channel name .................................................28 7 SCAN OPERATION .................................................2931 Scan types .............................................................................29 Programmed scan ................................................................29 Memory Scan ........................................................................30 Setting skip channels .............................................................30 Scan resume setting ..............................................................30 Priority watch .........................................................................31 8 TONE SQUELCH AND POCKET BEEP .................3234 Tone/DTCS squelch and pocket beep ....................................32 Tone scan...............................................................................34 9 DTMF MEMORY ......................................................3537 Programming a DTMF code sequence ..................................35 Transmitting a DTMF code sequence ....................................36 Confirming a DTMF memory .................................................37 Setting DTMF transfer speed .................................................37 10 SET MODES ............................................................3847 Set mode programming .........................................................38 Set mode items ......................................................................39 Initial Set mode programming................................................... 43 Initial Set mode items ............................................................44 11 CLONING ......................................................................48 Cloning operation ...................................................................48 12 RESETTING ..................................................................49 Resetting................................................................................49 13 TROUBLE SHOOTING TROUBLE SHOOTING ..................................................50 14 OPTIONS .................................................................5153 VOX function ..........................................................................52 15 SPECIFICATIONS .........................................................54 16 CE ............................................................................5556 TABLE OF CONTENTS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 vi 1 ACCESSORIES Antenna Insert the antenna into the antenna connector and twist the antenna to lock it in place. Belt clip To attach the belt clip:
Slide the belt clip in the direction of the arrow until the belt clip locks in place, and makes a click sound. Belt clip Battery pack/case CAUTION:
NEVER HOLD just the antenna when carrying the trans-
ceiver. Transmitting without an antenna will damage the trans-
ceiver. To detach the belt clip:
q Remove the battery pack/case from the transceiver, if it is attached. (p. 2). w Lift the tab up (q), and slide the belt clip in the direction of the arrow (w). q w 11 ACCESSORIES 1 Battery pack/case To attach the battery pack/case:
q Fit the battery pack/case in the direction of the arrow (q), then close. w Hook the latch until it makes a click sound (w). NEVER remove or attach the battery pack/case when the transceiver is wet or soiled. This may result in water or dust getting into the transceiver/battery pack/case, and may result in them being damaged. NOTE: Keep the battery terminals clean. Its a good idea to clean the battery terminals once a week. q Battery pack/case w Latch To remove the battery pack/case:
Unhook the latch (e), and lift up the battery pack/case in the direction of the arrow (r). r e Be careful! The latch is tightly locked, so use caution when releasing it. DO NOT use your finger nail. Use the edge of a coin or screwdriver tip to carefully release it. Jack cover Attach the jack cover when optional equipment is not used. To detach the jack cover To attach the jack cover q Attach the jack cover to e Remove the screws with a the [SP MIC] jack. w Tighten the screws. phillips screwdriver. r Detach the jack cover to connect optional equip-
ment. q w w e e r 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 2 2 PANEL DESCRIPTION Front, top and side panels w Speaker q Microphone Keypad (p. 4) 3 e r Function display (p. 6) t y u i q PTT SWITCH [PTT]
Push and hold to transmit, release to receive. (p. 17) For IC-V80E only Push briefly, then push and hold to transmit a 1750 Hz tone burst signal. (p. 22) w ANTENNA CONNECTOR Connect the antenna here. (p. 1) e CONTROL DIAL [VOL]
Adjust the volume level. (p. 14) During the Set mode, or Initial Set mode, rotate to se-
lect a desired option or value. (pp. 38, 43) r EXTERNAL SPEAKER/MICROPHONE JACKS [SP MIC]
Used to connect an optional speaker-microphone, plug adapter cable or cloning cable. The internal microphone and speaker will not function when an option is con-
nected. See page 51 for a list of available options. Be sure to turn power OFF before connecting/discon-
necting optional equipment to/from the [SP/MIC] jack. t MONITOR KEY [MONI]
Push and hold to open the squelch temporarily to mon-
itor the operating frequency. (p. 14) While pushing and holding this key, push [] or [] to adjust the squelch level. (p. 14) Enters or sends the DTMF code A. (pp. 35, 36) y POWER KEY [
Push and hold for 1 sec. to turn the transceiver power ON or OFF. (p. 14) D KEYPAD PANEL DESCRIPTION 2 u UP/DOWN KEYS []/[]
Push to change the operating frequency. (p. 16) During memory mode operation, push to select a memory channel. (p. 24) While scanning, push to change the scanning direction.
(pp. 29, 30, 31, 34) While pushing and holding [MONI], push to set the squelch level. (p. 14) During the Set mode, or Initial Set mode, push to se-
lect a desired setting item. (pp. 38, 43)
[] enters or sends the DTMF code B. (pp. 35, 36)
[] enters or sends the DTMF code C. (pp. 35, 36) i VFO/MEMORY/CALL KEY [VFO/MR/CALL]
Push to select the VFO mode, memory mode, a Call channel and a weather channel*, in sequence. (p. 15)
*Only the U.S.A. version transceivers. After pushing [FUNC](M), push to enter the memory programming mode. After pushing [FUNC](M), push and hold for 1 sec. to transfer a channel contents to a memory channel, or to the VFO mode. (p. 26) Enters or sends the DTMF code D. (pp. 35, 36) The functions of [VOL] and []/[] can be exchanged. See page 18 for details. Push to input numbers for frequency input and memory channel selection. Push to enter or send the DTMF code. (pp. 35, 36) To activate the second function of a key, first push
[FUNC](M), and then push the key.
[1] [ TONE](1) Numeric input and DTMF code: 1 After pushing [FUNC](M), selects the Tone func-
tion. (p. 33)
[2] [VOX](2) Numeric input and DTMF code: 2 After pushing [FUNC](M), turns the VOX function ON or OFF*. (p. 52)
* Only when an optional headset and plug adapter are connected. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 4 2 PANEL DESCRIPTION
[3] [T.SCAN](3) Numeric input and DTMF code: 3 After pushing [FUNC](M), starts a tone scan.
(p. 34)
[4] [DUP](4) Numeric input and DTMF code: 4 After pushing [FUNC](M), selects minus duplex, plus duplex, or simplex operation. (p. 21)
[5] [SCAN](5) Numeric input and DTMF code: 5 After pushing [FUNC](M), starts a scan. (pp. 29, 30)
[6] [SKIP](6) Numeric input and DTMF code: 6 After pushing [FUNC](M), sets or cancels the skip setting. (p. 30)
[7] [PRIO](7) Numeric input and DTMF code: 7 After pushing [FUNC](M), starts a priority watch.
(p. 31)
[8] [SET](8) Numeric input and DTMF code: 8 After pushing [FUNC](M), enters the Set mode.
(p. 38) 5
[9] [H/M/L](9) Numeric input and DTMF code: 9 After pushing [FUNC](M), selects the output power between high, middle and low. (p. 17)
[0] [DTMF-M](0) Numeric input and DTMF code: 0 After pushing [FUNC](M), enters the DTMF memory mode. (p. 35)
[M] [FUNC](M) DTMF code: M (indication: E) Push to access the second function of other keys.
](# ENT)
[# ENT] [
DTMF code: # (indication: F) After entering a frequency, stores the frequency.
(p. 16) Push to exit the Set mode or Initial Set mode.
(pp. 38, 43) After pushing [FUNC](M), push and hold for 1 sec. to turn the key lock function ON or OFF (p. 18) Function display t q w e r
!5
!4
!3
!1!2
!0 y u i o q BUSY INDICATOR Appears when a signal is being received, or the squelch is open. Blinks while the monitor function is ON. (p. 14) w SIGNAL INDICATOR Shows the strength of the received signal. (p. 17) Weak RX Signal level Strong While transmitting, shows the output power level.
(p. 17) Low Middle High PANEL DESCRIPTION 2 e TONE INDICATOR appears while the repeater tone encoder is ON.
(p. 20) appears while the tone squelch function is ON.
(p. 33) D appears while the DTCS squelch function is ON.
(p. 33) appears with the or D indicator while the pocket beep function (with CTCSS or DTCS) is ON. (p. 33) r MEMORY INDICATOR Appears when the memory mode is selected. (pp. 15, 24) t FREQUENCY READOUT Displays the operating frequency, memory channel, Set modes contents and a variety of other information. The decimal point blinks during scan. During memory mode operation, the programmed memory name is displayed. y BATTERY INDICATOR (p. 13)
(battery indicators) appear when the battery pack/case is attached. appears when the battery pack must be changed, or batteries must be replaced. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 6 2 PANEL DESCRIPTION u KEY LOCK INDICATOR Appears when the key lock function is ON. (p. 18) i VOX INDICATOR Appears when the VOX function is ON. (p. 52) o POWER INDICATOR (p. 17) H appears when high power is selected. M appears when middle power is selected. L appears when low power is selected.
!0 MEMORY CHANNEL NUMBER INDICATOR Displays the selected memory channel number. (p. 24) C appears when the Call channel is selected. (p. 24)
!1 AUTO POWER OFF INDICATOR Displays when the Auto Power OFF function is ON. (p. 44)
!2 DUPLEX INDICATOR (p. 21)
+ appears when plus duplex is selected. appears when minus duplex is selected.
!3 SKIP INDICATOR Appears when the selected memory channel is set as a skip channel. (p. 30)
!4 FUNCTION INDICATOR Appears when the second function can be accessed.
!5 TRANSMIT INDICATOR Appears while transmitting. (p. 17) 7 Caution (for the BP-264 Ni-MH battery) R DANGER! NEVER short terminals (or charging terminals) of the battery pack. Also, current may flow into nearby metal objects such as a necklace, so be careful when placing bat-
tery packs (or the transceiver) in handbags, etc. Simply carrying with or placing near metal objects such as a necklace, etc. may cause shorting. This may damage not only the battery pack, but also the transceiver. R DANGER! NEVER incinerate used battery packs. Internal battery gas may cause an explosion. R DANGER! NEVER immerse the battery pack in water. If the battery pack becomes wet, be sure to wipe it dry BE-
FORE attaching it to the transceiver. CAUTION: Always use the battery within the specified tem-
perature range, 5C to +60C (+23F to +140F). Using the battery out of its specified temperature range will reduce the batterys performance and battery life. CAUTION: Shorter battery life could occur if the battery is left completely discharged, or in an excessive temperature environment (above +55C; +131F) for an extended period of time. If the battery must be left unused for a long time, it must be detached from the radio after charging. Keep it safely in a cool dry place at the following temperature range:
20C to +45C 20C to +35C 20C to +25C
(up to six months)
(up to a year*)
* We recommend charging the battery pack every 6 months.
(4F to +113F) (up to a month)
(4F to +95F)
(4F to +77F) BATTERY CHARGING 3 Clean the battery terminals to avoid rust or misscontact. Keep battery terminals clean. Its a good idea to clean bat-
tery terminals once a week. If your Ni-MH battery pack seems to have no capacity, even after being charged, completely discharge it by leaving the power ON overnight. Then, fully charge the battery pack again. If the battery pack still does not retain a charge (or only very lit-
tle charge), a new battery pack must be purchased. (p. 51) Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. Recommended temperature range for charging:
between +10C and +40C (rapid charge: with BC-191) or between 0C and +45C (regular charge: with BC-192) Use the supplied charger or optional charger (BC-191 for rapid charging, BC-192 for regular charging) only. NEVER use other manufacturers chargers. The battery pack contains a rechargeble battery. Charge the battery pack before first operating the trans-
ceiver, or when the battery pack becomes exhausted. If you want to prolong the battery life, the following points should be observed:
Avoid over charging. The charging time period should be less than 48 hours. Use the battery pack until it becomes almost completely exhausted, under normal conditions. We recommend bat-
tery charging after transmitting becomes impossible. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 8 3 BATTERY CHARGING Caution (for the BP-265 Li-Ion battery) Misuse of Li-Ion batteries may result in the following haz-
ards: smoke, fire, or the battery may rupture. Misuse can also cause damage to the battery or degradation of battery performance. R DANGER! Use and charge only specified Icom battery packs with Icom radios or Icom chargers. Only Icom battery packs are tested and approved for use with Icom radios or charged with Icom chargers. Using third-party or counterfeit battery packs or chargers may cause smoke, fire, or cause the battery to burst. D Battery caution R DANGER! DO NOT hammer or otherwise impact the bat-
tery. Do not use the battery if it has been severely impacted or dropped, or if the battery has been subjected to heavy pressure. Battery damage may not be visible on the outside of the case. Even if the surface of the battery does not show cracks or any other damage, the cells inside the battery may rupture or catch fire. R DANGER! NEVER use or leave battery pack in areas with temperatures above +60C (+140F). High tempera-
ture buildup in the battery, such as could occur near fires or stoves, inside a sun heated car, or in direct sunlight may cause the battery to rupture or catch fire. Excessive temper-
atures may also degrade battery performance or shorten battery life. 9 R DANGER! DO NOT expose the battery to rain, snow, sea-
water, or any other liquids. Do not charge or use a wet battery. If the battery gets wet, be sure to wipe it dry before using. R DANGER! NEVER incinerate a used battery pack since internal battery gas may cause it to rupture, or may cause an explosion. R DANGER! NEVER solder the battery terminals, or NEVER modify the battery pack. This may cause heat gener-
ation, and the battery may burst, emit smoke or catch fire. R DANGER! Use the battery only with the transceiver for which it is specified. Never use a battery with any other equipment, or for any purpose that is not specified in this in-
struction manual. R DANGER! If fluid from inside the battery gets in your eyes, blindness can result. Rinse your eyes with clean water, without rubbing them, and see a doctor immediately. R WARNING! Immediately stop using the battery if it emits an abnormal odor, heats up, or is discolored or deformed. If any of these conditions occur, contact your Icom dealer or distributor. R WARNING! Immediately wash, using clean water, any part of the body that comes into contact with fluid from in-
side the battery. R WARNING! NEVER put the battery in a microwave oven, high-pressure container, or in an induction heating cooker. This could cause a fire, overheating, or cause the battery to rupture. CAUTION: Always use the battery within the specified tem-
perature range, 20C to +60C (4F to +140F). Using the battery out of its specified temperature range will reduce the batterys performance and battery life. CAUTION: Shorter battery life could occur if the battery is left fully charged, completely discharged, or in an excessive temperature environment (above +50C; +122F) for an ex-
tended period of time. If the battery must be left unused for a long time, it must be detached from the radio after discharg-
ing. You may use the battery until the battery indicator shows half-capacity, and then keep it safely in a cool dry place at the following temperature range:
20C to +50C 20C to +35C 20C to +20C
(4F to +122F) (up to a month)
(4F to +95F)
(4F to +68F)
(up to three months)
(up to a year) D Charging caution R DANGER! NEVER charge the battery pack in areas with extremely high temperatures, such as near fires or stoves, inside a sun-heated vehicle, or in direct sunlight. In such en-
vironments, the safety/protection circuit in the battery will ac-
tivate, causing the battery to stop charging. BATTERY CHARGING 3 R WARNING! DO NOT charge or leave the battery in the battery charger beyond the specified time for charging. If the battery is not completely charged by the specified time, stop charging and remove the battery from the battery charger. Continuing to charge the battery beyond the specified time limit may cause a fire, overheating, or the battery may rup-
ture. R WARNING! NEVER insert the transceiver (battery at-
tached to the transceiver) into the charger if it is wet or soiled. This could corrode the battery charger terminals or damage the charger. The charger is not waterproof. CAUTION: DO NOT charge the battery outside of the spec-
ified temperature range: BC-193 (+10C to +40C; +50F to +104F). Icom recommends charging the battery at +20C
(+68F). The battery may heat up or rupture if charged out of the specified temperature range. Additionally, battery perfor-
mance or battery life may be reduced. The supplied battery pack, charger, and AC adapter dif-
fer, or no supplied depending on the version. Prior to using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 10 3 BATTERY CHARGING Battery chargers D Using the BC-191 to rapid charge the BP-264 The BC-191 provides rapid charging of only the BP-264 Ni-MH battery pack. Never use it to charge any other battery pack. Charging time: Approx. 2 hours The following item is additionally required:
An AC adapter (not supplied with some versions) or the OPC-515L or CP-23L DC power cable. AC adapter
(A different type, or no AC adapter is supplied, de-
pending on the version.) Battery pack Transceiver D Using the BC-192 to regular charge the BP-264 The BC-192 provides regular charging of only the BP-264 Ni-MH battery pack. Never use it to charge any other battery pack. Charging time (with the 147S): Approx. 16 hours The following item is additionally required:
An AC adapter (not supplied with some versions) or the OPC-515L DC power cable. AC adapter
(A different type, or no AC adapter is supplied, de-
pending on the version.) Battery pack Transceiver Turn power OFF Screws*
(Self tapping screw:
M3.5 at least 30 mm)
*Purchase separately. is Using screws recommended to secure the charger. Charge indicator Lights orange : While charging Lights green : Charging is completed. The optional OPC-
515L (for DC power source) can be used instead of the AC adapter. Charging time period differs depending on the input voltage. 12 V
: Approx. 36 hours 13.8 V : Approx. 21 hours 16 V
: Approx. 16 hours Turn power OFF Screws*
(Self tapping screw:
M3.5 at least 30 mm)
*Purchase separately. is Using screws recommended to secure the charger. Charge indicator Lights green while charging. NOTE:
The charge indicator will not go out even after a battery pack is fully charged. The optional OPC-
515L (for DC power source) or CP-23L
(for 12 V cigarette lighter socket) can be used instead of the AC adapter. 11 D Using the BC-193 to rapid charge the BP-265 The BC-193 provides rapid charging of only the BP-265 Li-
Ion battery pack. Never use it to charge any other battery pack. Charging time: Approx. 2.5 hours The following item is additionally required:
An AC adapter (not supplied with some versions) or the OPC-515L or CP-23L DC power cable. AC adapter
(A different type, or no AC adapter is supplied, de-
pending on the version.) Battery pack Transceiver Turn power OFF Screws*
(Self tapping screw:
M3.5 at least 30 mm)
*Purchase separately. is Using screws recommended to secure the charger. Charge indicator Lights orange : While charging Lights green : Charging is completed. The optional OPC-
515L (for DC power source) or CP-23L
(for 12 V cigarette lighter socket) can be used instead of the AC adapter. BATTERY CHARGING 3 IMPORTANT: Battery charging caution Ensure the tabs on the battery pack are correctly aligned with the guide rails inside the charger. Tabs Guide rail CAUTION: When using the OPC-515L DC power cable NEVER connect the OPC-515L to a power source using reverse polarity. This will ruin the battery charger. White line: + Black line:
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 12 3 BATTERY CHARGING Battery case (BP-263) When using the battery case (BP-263), install 6 AA (LR6) size alkaline batteries, as described below. q Remove the battery case if it is attached. (p. 2) w Install 6 AA (LR6) size alkaline batteries. Install only alkaline batteries. Be sure to observe the correct polarity. e Attach the battery case. (p. 2) Be careful! The negative terminals of the battery case protrude from the body, so pay attention not to injure your fingers when inserting the batteries. CAUTION:
When installing batteries, make sure they are all the same brand, type and capacity. Also, do not mix new and old bat-
teries together. Keep battery terminals clean. Its a good idea to clean bat-
tery terminals once a week. Never incinerate used battery cells since the internal bat-
tery gas may cause them to rupture. Never expose a detached battery case to water. If the battery case gets wet, be sure to wipe it dry before using it. Never use batteries whose insulated covering is damaged. NOTE: When the battery case is attached, the battery protection function must be turned OFF in the Initial Set mode (p. 47). 13 Battery information D Battery life Battery pack/case Voltage Capacity Battery life*1 BP-263 BP-264 BP-265 Battery case for AA (LR6) 6 alkaline 1400 mAh 7.2 V 7.4 V 1900 mAh (min.) 2000 mAh (typ.)
*2 13 hrs. 19 hrs.
*1 When the power save function is set to PS.At, and the operating time is calculated under the following conditions;
TX : RX : standby = 5 : 5 : 90
*2 The average operating life depends on the alkaline cells used. Even when the transceiver power is OFF, a small current still flows in the transceiver. Remove the battery pack/case when it wont be used for a long time. Otherwise, the battery pack or the batteries in the case will become exhausted. D Battery indication The battery indicator, case is attached to the transceiver.
, appears when a battery pack/
Indicator Battery condition The battery has ample capacity. The battery is nearing exhaustion. Charging the battery pack, or replacing the batteries in the case is necessary. Power ON Push and hold [
Push and hold [
] for 1 sec. to turn the power ON.
] for 1 sec. to turn the power OFF. BASIC OPERATION 4 Adjusting the squelch level While pushing and holding [MONI], push [] or [] sev-
eral times to adjust the squelch level. SqL 1 is loose squelch (for weak signals) and SqL10 is tight squelch (for strong signals). SqL 0 is open squelch. Adjusting the volume level Rotate [VOL] to adjust the volume level. If the squelch is closed, push and hold [MONI] while adjusting the volume level. The display shows the volume level while adjusting. Monitor function This function is used to listen to weak signals or to open the squelch manually. You can use it without disturbing the squelch setting, even when mute functions such as the tone squelch are in use. Push and hold [MONI] to monitor the operating frequency. blinks while the monitor function is ON. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 14 4 BASIC OPERATION Mode selection Push [VFO/MR/CALL] several times to select the VFO mode, memory mode, Call channel mode and weather channel mode*, in se-
quence.
*For only the U.S.A. version transceivers. D VFO mode The VFO mode is used to set the operating frequency. VFO mode display What is VFO?
VFO is an abbreviation of Variable Frequency Oscillator. Fre-
quencies for both transmitting and receiving are generated and controlled by the VFO. 15 D Memory mode The memory mode is used for operating on memory channels, which store programmed fre-
quencies. appears when the memory mode is selected. D Call channel mode The Call channel is used for quick recall of the most often-
used frequency. C appears instead of the memory channel number when the Call channel mode is selected. Memory mode display Appears Call channel mode display Appears D Weather channel mode*
There are 10 weather channels for monitoring weather broad-
casts from NOAA (National Oceanic and Atmospheric Ad-
ministration).
* Only for the U.S.A. version trans-
ceivers. Weather channel mode display Operating mode selection Operating modes are determined by the modulation of the radio signals. The transceiver has the FM and FM-N modes. The mode selection is independently stored for each memory channel. q Push [FUNC](M) then [SET](8) to enter the Set mode. w Push [] or [] to select the operating mode item. (W/n) e Rotate [VOL] to set the operating mode to FM or FM-N. FM mode FM-N mode r Push [# ENT] to exit the Set mode. Setting a tuning step The transceiver has 8 tuning step options;
5 kHz 25 kHz 12.5 kHz 50 kHz 10 kHz 30 kHz 15 kHz BASIC OPERATION 4 Setting a frequency D Using [] or []
q Push [VFO/MR/CALL] several times to select the VFO mode. w Push [] or [] to select the desired frequency. The frequency changes according to the preset tuning steps. See the previous topic to set the tuning step. D Using the keypad q Push [VFO/MR/CALL] several times to select the VFO mode. w To enter the desired frequency, enter 6 digits, starting from 100 MHz digit. Entering two or three* to five digits, and then pushing [# ENT], also sets the frequency. (*Depending on the version) If a frequency outside the frequency range is entered, the previ-
ously displayed frequency is automatically recalled. 20 kHz Example 1 entering 145.525 MHz Push The tuning step can be selected in the Set mode. q Push [FUNC](M), and then [SET](8) to enter the Set mode. w Push [] or [] to select the tuning step item. (tS) e Rotate [VOL] to select the 20 kHz tuning step desired tuning step. r Push [# ENT] to exit the Set mode. Example 2 entering 144.800 MHz Push 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 16 4 BASIC OPERATION Receiving Make sure the BP-264 or BP-265 battery pack is fully charged, or the BP-263 battery case has brand new alkaline batteries (pp. 1113). q Push and hold [
w Rotate [VOL] to set the desired volume level. (p. 14) The volume level is displayed on the LCD while adjusting.
] for 1 sec. to turn power ON. e Set the receive frequency. (p. 16) r Set the squelch level. (p. 14) While pushing and holding [MONI], push [] or []. The squelch level is displayed on the LCD while setting. SqL 1 is loose squelch (for weak signals) and SqL10 is tight squelch (for strong signals). SqL 0 is open squelch. Push and hold [MONI] to open the squelch manually. t When a signal is received:
The squelch is opened and the audio is heard. The signal indicator shows the relative signal strength level. Transmitting CAUTION: Transmitting without an antenna will damage the transceiver. NOTE: To prevent interference, push and hold [MONI] to listen on the frequency before transmitting. q Set the operating frequency. (p. 16) w Push [FUNC](M), and then push [H/M/L](9) to select the output power between High (5.5 W), Mid (2.5 W) and Low
(0.5 W). H, M, or L appears according to the selected output power. e Push and hold [PTT] to transmit. appears while transmitting. The signal indicator shows the output power level. r Speak into the microphone using your normal voice level. DO NOT hold the transceiver too close to your mouth or speak too loudly. This may distort your speech. t Release [PTT] to return to receive. w Adjust the volume level. r For the squelch level setting. q Turn the power ON.
(Push to monitor) e Set the frequency. r Adjust the squelch level. 17 e Push and hold to transmit. t Release to receive. Microphone w Select the output power. Push to monitor. q Set the frequency. Key lock function To prevent accidental frequency changes, or unnecessary function access, use the key lock function. Push [FUNC](M), and then push and hold [
](# ENT) for 1 sec. to turn the key lock function ON or OFF.
appears while the key lock function is activated.
], [VOL], [MONI], [PTT] and [FUNC](M) + [
are still operable while the key lock function is ON.
](# ENT) Appears BASIC OPERATION 4
[VOL] function assignment
[VOL] can be used as a tuning control instead of [] and
[], to suit your preference. However, when [VOL] functions as a tuning control, [] and [] function as volume controls. q While pushing and holding [] and [], turn the power ON to enter the Initial Set mode. w Push [] or [] to select the dial assignment item. (tOP) e Rotate [VOL] to select an option. r Push [# ENT] to exit the Initial Set mode.
[VOL]
[VOL] functions as the volume control.
[VOL] functions as the tuning control.
[VOL] and []/[] function as described below, depend-
ing on the option. Option tOP.VO tOP.di
[VOL]
Volume control Tuning control
Tuning controls Volume controls 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 18 4 BASIC OPERATION Weather channel operation There are 10 weather channels for monitoring weather broadcasts from NOAA (National Oce-
anic and Atmospheric Administration). D Weather channel selection q Push [VFO/MR/CALL] several times to select the weather channel mode. Weather channel mode display w Push [] or [] to select a weather channel. e Push [VFO/MR/CALL] to return to the previous frequency or memory channel. D Weather alert function NOAA broadcast stations transmit weather alert tones be-
fore important weather announcements. When the weather alert function is ON, the selected weather channel is moni-
tored every 5 sec. for announcements. When the alert signal is detected, the ALt and the WX channel number are alter-
nately displayed, and a beep sounds until the transceiver is operated. The previously selected (used) weather channel is checked periodically during standby, or while scanning. 19 U.S.A. version only q Select a weather channel. w Turn the weather alert function ON in the Set mode. Push [FUNC](M), and then [SET](8) to enter the Set mode. Push [] or [] to select the weather alert item. (ALt) Rotate [VOL] to select ON. Push [# ENT] to exit the Set mode. e Set the desired stand-by mode. Select the VFO, memory or Call channel mode. Scan or priority watch operation can also be selected. r When an alert is detected, a beep sounds, and ALt and the weather channel number will be alternately displayed. t Turn the weather alert function OFF in the Set mode. NOTE: While receiving a signal on a frequency other than the Weather alert frequency, the receiving signal will be interrupted momentarily approximately every 5 sec. when the weather alert function is ON. These interruptions cease when the weather alert function is turned OFF. Push [FUNC](M), and then [SCAN](5) to start a weather channel scan. Push any key except []/[], [FUNC](M) and [MONI] to stop the scan. REPEATER AND DUPLEX OPERATION 5 Repeater operation When using a repeater, the transmit frequency is shifted from the receive frequency by the frequency offset (p. 21). This is called duplex operation. It is convenient to program repeater information into memory channels (p. 25). Repeater 144.700 MHz 144.700 MHz 145.300 MHz 145.300 MHz Uplink
(transmit freq.) Downlink
(receive freq.) Station B Station A q Set the receive frequency (the repeater output frequency). w Push [FUNC](M), and then [DUP](4) several times to set the shift direction of the transmit frequency. ( or +;
See page 21 for details.) When the auto repeater function is in use (U.S.A. version only), this selection and step e are not necessary. (p. 23). e If desired, push [FUNC](M) and then [TONE](1) several times to activate the subaudible tone encoder. appears. Select the desired subaudible Appears tone frequency. (p. 22) r Push and hold [PTT] to transmit. The displayed frequency automatically changes to the transmit frequency (repeater input frequency). If OFF appears, check the frequency offset and shift direction
(p. 21). t Release [PTT] to receive. While receiving While transmitting y Push and hold [MONI] to check whether the other stations transmit signal can be directly received or not. When the other stations signal can be directly received, move to a non-repeater frequency to use simplex. (duplex OFF) For the U.S.A. version:
Auto repeater function uses standard values of the re-
peater tone frequency and frequency offset. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 5 REPEATER OPERATION Duplex operation D Setting the frequency offset q Push [FUNC](M), and then [SET](8) to enter the Set mode. w Push [] or [] to select the offset item. e Rotate [VOL] to select the frequency offset. 0.6 MHz offset blinks, and the current frequency offset appears. The offset is selected in the same step as the frequency tuning step. The unit of the frequency offset is MHz. r Push [# ENT] to exit the Set mode. D Setting the duplex direction Push [FUNC](M), and then [DUP](4) to select (nega-
tive offset) or + (positive offset). or + indicates the transmit frequency is shifter up (+) or down () from the receive frequency. Blinking or + indicates the reverse duplex function is ON, as described to the right. Example When the offset frequency is 0.6 MHz While receiving While transmitting Duplex
+ (up)
(down) 21 For the U.S.A. version:
The auto repeater function has priority over the manual duplex setting. If the transmit frequency changes after setting, the auto repeater function may have changed the duplex setting. Turn the auto repeater function OFF to prevent this (p. 23). D Reverse duplex function When the reverse duplex function is ON, the receive and transmit frequencies are reversed. The function can be set in the Set mode. q Push [FUNC](M), and then [SET](8) to enter the Set mode. w Push [] or [] to select the reverse duplex function item
(REV). e Rotate [VOL] to turn the function ON or OFF. r Push [# ENT] to exit the Set mode. Each receive and transmit frequency is shown in the table below, with the following configurations;
Input freq. : 145.300 MHz Direction Offset
: (down)
: 0.6 MHz Reversed RX freq. TX freq. OFF ON 145.300 MHz 144.700 MHz 144.700 MHz 145.300 MHz or + blinks when the re-
verse duplex function is ON. Subaudible tones Some repeaters require subaudible tones to be accessed. Subaudible tones are superimposed over your normal sig-
nal, and must be set in advance. q Push [FUNC](M) then [SET](8) to enter the Set mode. w Push [] or [] to select the repeater tone item. (rt) e Rotate [VOL] to select the desired subaudible tone.
[VOL]
88.5 Hz repeater tone r Push [# ENT] to exit the Set mode. Available subaudible tone frequencies
(unit: Hz) 67.0 69.3 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 97.4 100.0 103.5 107.2 110.9 114.8 118.8 123.0 127.3 131.8 136.5 141.3 146.2 151.4 156.7 159.8 162.2 165.5 167.9 171.3 173.8 177.3 179.9 183.5 186.2 189.9 192.8 196.6 199.5 203.5 206.5 210.7 218.1 225.7 229.1 233.6 241.8 250.3 254.1 REPEATER OPERATION 5 D Tone information Some repeaters require a different tone system to be ac-
cessed. DTMF TONES While pushing [PTT], push the desired DTMF keys, [0] to
[9], [MONI](A), [](B), [](C), [VFO/MR/CALL](D), [M](E), and [# ENT](F), to transmit their assigned DTMF codes. The transceiver has 16 DTMF memory channels (p. 35). 1750 Hz TONE To access some European repeaters, the transceiver must transmit a 1750 Hz tone burst. For IC-V80E only Push [PTT] briefly, push and hold [PTT] again for 1 or 2 sec. For other transceivers While pushing [PTT], push and hold either the [] or [] for 1 or 2 sec. See page 36 for details. CONVENIENT!
Tone scan function:
If you dont know the subaudible tone used for a repeater, the tone scan is convenient for detecting the tone frequency. Push [FUNC](M), and then [T.SCAN](3) to start a tone scan. When the required tone frequency is detected, the scan pauses, and the tone frequency is temporarily set. See page 34 for details of the tone scan function. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 22 5 REPEATER OPERATION Lockout function The lockout function helps prevent interference to other sta-
tions by inhibiting transmitting when the channel is busy. The function can be set in the Initial Set mode. q While pushing and holding [] and [], turn the power ON to enter the Initial Set mode. w Push [] or [] to select the lockout item. (RLO) e Rotate [VOL] to select the lockout function option be-
tween OFF, repeater lockout, and busy lockout. RLO.OF : Allows transmitting, even if signals are received. RLO.RP : The repeater lockout function inhibits transmitting when the channel is busy, except while receiving a signal that includes a matched subaudible tone.
: The busy lockout function inhibits transmitting while receiving a signal. RLO.bU r Push [# ENT] to exit the Initial Set mode.
[VOL]
Auto repeater function U.S.A. version only The auto repeater function sets the standard repeater set-
tings (duplex ON/OFF, duplex direction, tone encoder ON/OFF) when the operating frequency falls within or outside of the general repeater output frequency range. The offset and repeater tone frequencies are not changed by the auto re-
peater function. Reset these frequencies, if necessary. The function can be set in the Initial Set mode. q While pushing and holding [] and [], turn the power ON to enter the Initial Set mode. w Push [] or [] to select the auto repeater item. (RPt) e Rotate [VOL] to select a desired option. Rpt.OF : Turns the function OFF. Rpt.R1 : The auto repeater function is activated for duplex only. Rpt.R2 : The auto repeater function is activated for duplex and tone encoder. r Push [# ENT] to exit the Initial Set mode. The repeater lockout function is ON. Frequency range and offset direction Frequency range Duplex direction 145.200 to 145.495 MHz 146.610 to 146.995 MHz 147.000 to 147.395 MHz appears.
+ appears. 23 MEMORY/CALL OPERATION 6 General description The transceiver has 207 memory channels, including 6 scan edge memory channels (3 pairs), and 1 Call channel, for storage of often-used frequencies. D Memory channel contents The following information can be programmed into a mem-
ory channel:
Operating frequency (p. 16) Operating mode (p. 16) Duplex direction (+ or ) with frequency offset (p. 21) Reverse duplex function ON/OFF (p. 40) Subaudible tone encoder (p. 20), tone squelch or DTCS squelch ON/OFF (p. 33) D Using the keypad q Push [VFO/MR/CALL] several times to select the memory mode. X appears. w To select a desired channel, enter the 3 digits of the chan-
nel number using the keypad. Blank channels are also selectable. Entering one or two digits, and then pushing [# ENT] also se-
lects a memory channel. Example selecting memory channel 14 Push Subaudible tone frequency (p. 22), tone squelch frequency or DTCS code with polarity (pp. 32, 33) Appears The memory channel is selected. Skip setting (p. 30) Tuning step (p. 16) Output power (p. 17) TX permission (p. 41) Selecting a memory channel D Using [] or []
q Push [VFO/MR/CALL] several times to select the memory mode. X appears. w Push [] or [] to select a desired channel. Only programmed channels are displayed. Selecting the Call channel Push [VFO/MR/CALL] several times to select the Call channel. C appears instead of the memory channel number. Push Appears 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 24 6 MEMORY/CALL OPERATION Channel programming q Push [VFO/MR/CALL] several times to select the VFO mode. w Set a desired frequency. (p. 16) If desired, set other data (e.g. offset frequency, duplex direction, tone squelch, etc.). e Push [FUNC](M), and then [VFO/MR/CALL]. X and the memory channel number blink. Select the Call channel mode to program the Call channel. r Push [] or [] to select a desired channel. Select 1A/1B to 3A/3B to program a scan edge channel. t Push [FUNC](M), and then push and hold [VFO/MR/
CALL] for 1 sec. to store the entry. 3 beeps sound. If you continue to push and hold [VFO/MR/CALL] for 1 sec. after programming, the memory channel number automatically increases. NOTE: To cancel programming, push [VFO/MR/CALL]
before storing the entry in step t. Example programming 145.440 MHz into memory channel 11 (a blank channel). Push , and then . Push or to select channel 11. The VFO mode Push , then push and hold for 1 sec. to program. 25 Return to the VFO mode. MEMORY/CALL OPERATION 6 Copying memory/Call contents This function transfers a memory channels contents to VFO (or another memory/Call channel). This is useful when searching for signals around a memory channel frequency and for recalling the offset frequency, subaudible tone fre-
quency etc. D Memory/CallVFO q Select a memory (Call) channel to be copied. Push [VFO/MR/CALL] several times to select the memory or Call channel mode, and then push [] or
[] to select a desired channel. w Push [FUNC](M), and then push and hold [VFO/MR/
CALL] for 1 sec. to transfer the selected memory contents to the VFO mode. The VFO mode is automatically selected. D Memory/Callmemory/Call q Select a memory or Call channel to be copied. Push [VFO/MR/CALL] several times to select the memory mode or the Call channel mode, and then push [] or [] to select a desired channel. w Push [FUNC](M), and then push [VFO/MR/CALL]. X and -- blink. Do not hold [VFO/MR/CALL] for more than 1 sec., otherwise the memory contents will be copied to the VFO mode. e Push [] or [] to select the target memory or Call chan-
nel. r Push [FUNC](M), and then push and hold [VFO/MR/
CALL] for 1 sec. to copy. Example copying memory channel 11 to the VFO mode. Push , then push and hold for 1 sec. Memory mode VFO mode. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 26 6 MEMORY/CALL OPERATION Clearing memory contents The contents of programmed memories can be cleared
(erased). q For only the U.S.A. version, select any mode other than the weather channel mode. w Push [FUNC](M), and then push [VFO/MR/CALL]. e Push [] or [] to select a channel to be cleared. r Perform the following operation within 1.5 sec., otherwise the transceiver returns to the memory mode without clear-
ing memory.
- Push [FUNC](M), and then momentarily push [VFO/MR/
CALL].
- Push [FUNC](M), and then push and hold [VFO/MR/
CALL] for 1 sec. The channel contents are cleared. t Push [VFO/MR/CALL] to return to the previous mode. NOTE: Be careful! the contents of cleared memories CANNOT be recalled. 27 Display type During memory mode operation, the transceiver has 3 dis-
play types to suit your operating style. Set the display type in the Initial Set mode. (p. 46) Frequency display Displays the programmed frequency. Channel number display Displays the memory channel num-
ber. Only programmed channels are displayed, and modes other than the memory mode cannot be selected. When the channel number display type is selected, only the follow-
ing functions can be performed.
- Scan function (p. 30)
- DTMF memory function (p. 35)
- The scan pause timer setting, the function key timer setting, the LCD backlight setting, the VOX-related settings, the microphone gain setting, and the DTMF TX key setting in the Set mode.
- Out put power setting (p. 17)
- Key lock function (p. 18) Channel name display Displays the channel name you have assigned. Only programmed chan-
nels are displayed. If no channel name is programmed, the programmed frequency will be displayed. Push [MONI] to display the operating frequency. MEMORY/CALL OPERATION 6 Programming a channel name Each memory channel can be programmed with an alphanu-
meric name for easy recognition and can be displayed inde-
pendently by channel. Up to 5 characters can be used for a channel name. i Rotate [VOL] to select a desired character. The selected character blinks. Push [] to move the cursor right, push [] to move the cur-
sor left.
[VOL]
o Repeat step i until the desired channel name is pro-
grammed.
!0 Push [# ENT] to exit the programming mode. q While pushing and holding [] and
[], turn the power ON to enter the Initial Set mode. w Push []/[] to select the channel name display item. (dSP) e Rotate [VOL] to select the channel name display type, dSP.nm. r Push [# ENT] to exit the Initial Set mode. t Push [VFO/MR/CALL] several times to select the memory mode. Select the Call channel to program a Call channel name. y Push [] or [] to select a desired channel. u Push [FUNC](M), and then [SET](8) to enter the channel name programming mode. A cursor blinks for the first character. D Usable characters
(A)
(b)
(C)
(d)
(E)
(F)
(G)
(H)
( I )
(J)
(k)
(L)
(m)
(n)
(O)
(P)
(q)
(R)
(S)
(t)
(U)
(V)
(W)
(X)
(y)
(Z)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(0)
(Space) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 28 7 SCAN OPERATION Scan types A scan automatically searches for signals, and makes it easier to locate new stations for contact or listening purposes. PROGRAMMED SCAN (See the next topic) Band edge 1A 2A 3A Scan edges Scan Jump 1b 2b 3b Band edge The Programmed scan P1 scans between 1A and 1b, P2 scans between 2A and 2b, and P3 scans between 3A and 3b frequencies. MEMORY (SKIP) SCAN (p. 30) Mch 1 Mch 2 Mch 3 Mch 4 Mch 5 Mch 0 SKIP SKIP Mch 6 Mch 199 Mch 10 Mch 9 Mch 8 Mch 7 PRIORITY WATCH (p. 31) Memory/Call channel watch Memory scan watch 5 sec. VFO frequency Memory
(Call) channel 5 sec. SKIP VFO frequency Mch 0 Mch 1 Mch 2 Mch 199 29 Programmed scan A programmed scan repeatedly scans between two user programmed frequencies (memory channels 1A3A and 1b3b), or scans between upper and lower band edges. This scan is useful for checking for signals within a specific frequency range, such as repeater output frequencies, etc. q Push [VFO/MR/CALL] several times to select the VFO mode. w Push [FUNC](M), and then
[SCAN](5) to start a scan. e Push [FUNC](M), and then
[SET](8) several times to se-
lect a desired scan type be-
tween P1, P2, P3 or AL. AL for full scan, P1, P2 and P3 for programmed scan be-
tween the programmed scan edge channels 1A1b, 2A 2b and 3A3b. To change the scan direction, push [] or []. r To cancel the scan, push any key except [
[MONI] or [FUNC](M). NOTE: Scan edge channels, 1A3A/1b3b, must be pro-
grammed in advance. Program them in the same manner as regular memory channels. (p. 25) If identical frequencies are programmed into the scan edge channels, the programmed scan will not function. Memory Scan A memory scan repeatedly scans memory channels, except those set as skip channels. q Push [VFO/MR/CALL] several times to select the mem-
ory mode. X appears. w P u s h [ F U N C ] ( M ) , t h e n
[SCAN](5) to start the scan. To change the scan direction, push [] or []. e To cancel the scan, push any key except [
[MONI] or [FUNC](M). Setting skip channels In order to speed up the scan rate, you can set the memory channels you dont want to scan as skip channels. q Select a memory channel to be skipped. Push [VFO/MR/CALL] several times to select the memory mode, and then push [] or [] to select a desired channel. w Push [FUNC](M), and then
[SKIP](6) to turn the skip setting ON or OFF. SKIP appears when the chan-
nel is set as a skip channel. Appears SCAN OPERATION 7 Scan resume setting When a signal is received during a scan, the scan resume setting determines what action the transceiver takes. The transceiver has 2 scan resume settings, as described below. Use the Set mode to select the one which best suits your needs. q Push [FUNC](M), and then [SET](8) to enter the Set mode. w Push [] or [] to select the scan pause timer item (SCt, or SCP). e Rotate [VOL] to select a desired scan pause option. Pause scan The scan pauses until the received signal disappears, and then resumes after 2 sec. Timer scan The scan pauses for 5 sec., 10 sec. or 15 sec., and then resumes. r Push [# ENT] to exit the Set mode.
[VOL]
Pause scan Timer scan (15 sec.) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 30
1 | User Manual 2 | Users Manual | 1.61 MiB |
7 SCAN OPERATION Priority watch A priority watch checks for signals on priority channels while operating on a VFO frequency. D Memory or Call channel watch While operating on a VFO frequency, the memory or Call channel watch checks for signals on the selected channel every 5 sec. q Select a desired memory channel or the Call channel. w Push [FUNC](M), and then [PRIO](7) to start the watch. The decimal point ., on the frequency readout blinks. When a signal is detected on the channel, the watch resumes according to the scan resume setting. (p. 30) D Memory scan watch While operating on a VFO frequency, a memory scan watch checks for signals on each memory channel in sequence, every 5 sec. q Push [VFO/MR/CALL] several times to select the memory mode. w Push [FUNC](M), and then [SCAN](5) to start a memory scan. e Push [FUNC](M), and then [PRIO](7) to start the watch. The VFO mode is selected, and the decimal point ., on the fre-
quency readout blinks. When a signal is detected on a channel, the watch resumes ac-
VFO frequency Memory channel cording to the scan resume setting. (p. 30) 5 sec. e To cancel the watch, push any key except [
[MONI], [FUNC](M), or [PTT]. 5 sec. VFO frequency Memory scan SKIP Mch 0 Mch 1 Mch 2 Mch 199 r To cancel the watch, push any key except [
[MONI], [FUNC](M), or [PTT]. 31 TONE SQUELCH AND POCKET BEEP 8 Tone/DTCS squelch and pocket beep D Tone squelch and DTCS squelch The tone squelch (CTCSS) or DTCS squelch opens only when receiving a signal that includes a matched CTCSS tone or DTCS code, respectively. You can silently wait for calls using the same tone or code. Separate tone frequencies can be set for repeater and tone squelch/pocket beep operation. D Setting CTCSS tone or DTCS code q Push [FUNC](M), and then [SET](8) to enter the Set mode. w Push [] or [] to select the CTCSS tone item (Ct) or the DTCS code item (dt). blinks when selecting the CTCSS tone item, and D blinks when selecting the DTCS code item. D Pocket beep The pocket beep function uses subaudible tones or DTCS codes for calling, and can be used as a common pager to inform you that someone has called while you were away from the transceiver. e Rotate [VOL] to select a desired CTCSS tone or DTCS code. The recommended CTCSS tone or DTCS code are shown to the left. r Push [# ENT] to exit the Set mode. Recommended CTCSS tones 131.8 136.5 141.3 146.2 151.4 110.9 114.8 118.8 123.0 127.3 94.8 97.4 100.0 103.5 107.2 67.0 69.3 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5
(unit: Hz) 156.7 162.2 167.9 173.8 179.9 186.2 192.8 203.5 210.7 218.1 225.7 233.6 241.8 250.3
[VOL]
CTCSS tone setting DTCS code setting Recommended DTCS code 023 025 026 031 032 043 047 174 205 223 226 243 244 245 251 261 263 265 271 306 311 051 054 065 071 072 073 074 114 115 116 125 131 132 134 143 152 155 156 162 165 172 315 331 343 346 351 364 365 371 411 412 413 423 431 432 445 464 465 466 503 506 516 532 546 565 606 612 624 627 631 632 654 662 664 703 712 723 731 732 734 743 754 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 32 8 TONE SQUELCH AND POCKET BEEP D Setting DTCS polarity For DTCS operation, the polarity setting is also configurable, as well as the code setting. If the polarity is different, the DTCS squelch never opens, even when receiving a signal that includes a matched DTCS code. D Operation q Set a desired operating frequency, and then a CTCSS tone or a DTCS code. w Push [FUNC](M), and then [TONE](1). Repeat step w several times to activate a desired tone function. q Push [FUNC](M), and then [SET](8) to enter the Set mode. w Push [] or [] to select the DTCS polarity item (dtP). e Rotate [VOL] to select a desired polarity setting between dtP.nn (normal), dtP.nR (TX: normal, RX: reverse), dtP.Rn
(TX: reverse, RX: normal) and dtP.RR (reverse). Push , and then to select the tone function in sequence. Repeater tone Function OFF TX/RX: Normal polarity TX: Normal, RX: Reverse Tone squelch with pocket beep DTCS squelch TX: Reverse, RX: Normal TX/RX: Reverse polarity r Push [# ENT] to exit the Set mode. Tone squelch DTCS squelch with pocket beep e Operate the transceiver in a normal way. 33 r When receiving a signal that includes a matched tone or code, the squelch opens and the signal can be heard. When the pocket beep function is activated. Beep tones sound and blinks. To stop the beeps and blink-
ing, push any key. When the received signals tone/code does not match, the squelch does not open. However, the signal indicator shows the signal strength. To open the squelch manually, push and hold [MONI]. t Push [PTT] to answer. TONE SQUELCH AND POCKET BEEP 8 Tone scan By monitoring a signal from a repeater, pocket beep or squelch function operation, you can determine the subaudi-
ble tone required to access the repeater or open the squelch. q Set a frequency to be checked for a tone frequency or DTCS code. w Push [FUNC](M), and then [TONE](1). Repeat step w several times to activate a desired tone function. The tone scan can be made even if the tone function is not se-
lected. e Push [FUNC](M), and then [T.SCAN](3) to start a tone scan. To change the scan direction, push [] or []. r When a tone frequency or DTCS code is matched, the squelch opens and the tone frequency or code is tempo-
rarily programmed into the selected mode. When a tone frequency or DTCS code is detected, the tone scan pauses according to the scan resume setting (p. 30) The decoded CTCSS tone frequency or DTCS code is used ac-
cording to the selected tone function type in step w.
- No indication : Cannot be used for operation.
- D : DTCS tone encoder/decoder
: CTCSS tone encoder (repeater tone)
: CTCSS tone encoder/decoder t To cancel the scan, push any key except [
[MONI] or [FUNC](M). 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 34 9 DTMF MEMORY Programming a DTMF code sequence The DTMF codes are used for autopatching, accessing re-
peaters, controlling other equipment, and other operations. The transceiver has 16 DTMF memory channels (d0d9, dA, db, dC, dd, dE, dF) for storage of often-used DTMF code sequence of up to 24 digits. r Push keys to input a desired DTMF code sequence of up to 24 digits.
[0][9] inputs 09, [MONI] inputs A, [] inputs B, []
inputs C, [VFO/MR/CALL] inputs D, [M] inputs M (E) and [#
ENT] inputs # (F). q Push [FUNC](M), and then [DTMF.M](0) to enter the DTMF memory mode. If a digit is mistakenly input, push [PTT] momentarily, then re-
peat from step e. Push , and then . w Push [] or [] to select a desired DTMF memory chan-
nel. If programmed, the previously programmed DTMF code is dis-
played. e Push [FUNC](M), and then push and hold [DTMF.M](0) for 1 sec. to enter the programming mode. _ _ _ _ _ appears. Programmed memories will be cleared by this operation. Push , and then push and hold for 1 sec. The next page appears when the 6th digit has been input. t Repeat step r until the desired code is input. y Push [PTT] to store the DTMF code sequence and exit the programming mode. After the 24th digit is input, the transceiver automatically stores the code sequence and returns to step w. u Push [VFO/MR/CALL] to exit the DTMF memory. Programming mode indication The programming mode consists of 5 pages. Page 1st 2nd 3rd 4th 5th Digits 1st to 5th 6th to 10th 11th to 15th 16th to 20th 21st to 24th Indication No indication. appears. appears. appears. blinks. 35 DTMF MEMORY 9 Transmitting a DTMF code sequence The transceiver has 3 methods of transmitting a DTMF code sequence. Select a desired option in the Set mode. q Push [FUNC](M), and then [SET](8) to enter the Set mode. w Push [] or [] to select the DTMF TX key item (dmt). e Rotate [VOL] to select a desired option. dmt.k : Transmits the appropriate DTMF code assigned to the pushed key. dmt.m : Transmits the programmed DTMF code sequence in the dmt.t DTMF memory channel assigned to the pushed key.
: No DTMF code can be transmitted. However, while pushing and holding [PTT], pushing either the [] or
[] transmits a 1750 Hz tone burst signal. r Push [# ENT] to exit the Set mode. D Manual DTMF code transmission First, set the DTMF TX key to dmt.k in the Set mode. While pushing and holding [PTT], push the desired keys to transmit a DTMF code sequence manually. Push [0][9] for 09, [MONI] for A, [] for B, [] for C,
[VFO/MR/CALL] for D, [M] for M, and [# ENT] for #. D Using a DTMF memory channel First, set the DTMF TX key to dmt.m in the Set mode. While pushing and holding [PTT], push one of the keys to transmit the programmed DTMF code sequence in the DTMF memory. Pushing [0] to [9], [MONI](A), [](B), [](C), [VFO/MR/CALL]
(D), [M](E), or [# ENT](F) transmits a DTMF code channel (d0 d9, dA, dB, dC, dD, dE or dF) respectively. D 1750 Hz tone To access some European repeaters, the transceiver must transmit a 1750 Hz tone burst signal. This tone can be used as a Call signal in countries out of Europe. First, set the DTMF TX key to dmt.t in the Set mode. While pushing and holding [PTT], push and hold either the [] or [] for 1 or 2 sec. to transmit a 1750 Hz tone burst signal. While pushing and holding the key, the tone is transmitted. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 36 9 DTMF MEMORY Confirming a DTMF memory A DTMF memory can be confirmed with a DTMF tone. q Push [FUNC](M), and then [DTMF.M](0) to enter the DTMF memory mode. w Push [] or [] to select a desired DTMF memory chan-
nel. e Push [MONI] to confirm the DTMF memory contents. The programmed DTMF code sequence sounds. After sounding, the transceiver exits the DTMF memory mode. Setting DTMF transfer speed When slow DTMF transmission speeds are required with DTMF memory transmission (as for some repeaters), the transceivers rate of DTMF transmission can be adjusted in the Initial Set mode. q While pushing and holding [] and [], turn the power ON to enter the Initial Set mode. w Push [] or [] to select the DTMF speed item. (dtd) e Rotate [VOL] to select a desired speed. dtd. 1 : 100 msec. interval; 5.0 cps rate dtd. 2 : 200 msec. interval; 2.5 cps rate dtd. 3 : 300 msec. interval; 1.6 cps rate dtd. 5 : 500 msec. interval; 1.0 cps rate
(cps=characters per second) r Push [# ENT] to exit the Initial Set mode. The programmed DTMF code sequence sounds. Exits the DTMF memory mode. 37 Set mode programming The Set mode is used to change the settings of the trans-
ceivers functions. SET MODES 10 D Set mode operation q Push [FUNC](M), and then [SET](8) to enter the Set mode. w Push [] or [] to select the desired item. e Rotate [VOL] to select the option or value. r To exit the Set mode, push [# ENT]. Repeater tone frequency (p. 39) Tone squelch frequency (p. 39) DTCS code (p. 39) DTCS polarity (p. 39) Frequency offset (p. 40) Operating mode (p. 42) DTMF TX key (p. 42) VOX time-out timer (p. 42) VOX delay (p. 41)
: Push
: Push
*Appears for only the U.S.A. version transceivers. NOTE: When the display type setting (pp. 27, 46) is set to CH in the Initial Set mode, and accessing the Set mode from the memory mode, most of Set mode items do not appear. Reverse duplex functon (p. 40) Tuning step (p. 40) Scan resume setting (p. 40) Function key timer (p. 40) Microphone gain (p. 41) VOX gain (p. 41) Weather alert* (p. 41) TX permission (p. 41) LCD backlight (p. 41) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 38 10 SET MODES Set mode items D Repeater tone frequency Selects one of 50 subaudible tone frequencies used to ac-
cess the repeaters. 67.0254.1 Hz (default: 88.5 Hz) D Tone squelch frequency Selects one of tone frequencies for tone squelch or pocket beep operation. 67.0254.1 Hz (default: 88.5 Hz) D DTCS Code Selects one of 104 DTCS (both encoder/decoder) codes. 023754 (default: 023) Available DTCS codes 245 023 246 025 251 026 031 252 255 032 261 036 263 043 265 047 266 051 053 271 125 131 132 134 143 145 152 155 156 162 054 065 071 072 073 074 114 115 116 122 165 172 174 205 212 223 225 226 243 244 732 734 743 754 274 306 311 315 325 331 332 343 346 351 356 364 365 371 411 412 413 423 431 432 445 446 452 454 455 462 464 465 466 503 506 516 523 526 532 546 565 606 612 624 627 631 632 654 662 664 703 712 723 731 Usable subaudible tone frequencies
(unit: Hz) 67.0 69.3 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 97.4 100.0 103.5 107.2 110.9 114.8 118.8 123.0 127.3 131.8 136.5 141.3 146.2 151.4 156.7 159.8 162.2 165.5 167.9 171.3 173.8 177.3 179.9 183.5 186.2 189.9 192.8 196.6 199.5 203.5 206.5 210.7 218.1 225.7 229.1 233.6 241.8 250.3 254.1 The transceiver has 50 tone frequencies and conse-
quently their spacing is narrow compared with units hav-
ing 38 tones. Therefore, some tone frequencies may re-
ceive interference from adjacent tone frequencies. 39 D DTCS Polarity Selects the DTCS polarity between dtP.nn (normal), dtP.nR
(TX: normal, RX: reverse), dtP.Rn (TX: reverse, RX: normal) and dtP.RR (reverse).
(default: dtP.nn) The DTCS codes polarity for transmitting or receiving can be independently set by this item. TX/RX: Normal polarity TX/RX: Reverse polarity D Frequency offset Selects the frequency offset between 0 and 20 MHz, for re-
peater operation. The frequency offset means the difference between the transmit and receive frequencies.
(default: differs depending on the version) D Reverse duplex function Turns the reverse duplex function ON or OFF.
(default: OFF) D Tuning step Selects the tuning step from 5, 10, 12.5, 15, 20, 25, 30 and 50 kHz.
(default: differs depending on the version) SET MODES 10 D Scan resume setting Selects the scan resume setting between SCt. 5, SCt. 10, SCt. 15, and SCP. 2. When a signal is received during a scan, the scan pauses and then resumes, according to the scan resume setting. SCt. 5/10/15 : The scan pauses for 5, 10 or 15 sec., and then re-
sumes. (default: SCt. 15)
: The scan pauses until the received signal disap-
pears, and then resumes after 2 sec. SCP.2 D Function key timer Push [FUNC](M) to enter the Function mode, and then push a keypad key to activate its second function. During the Function mode, Set the time between when Function mode is entered, and how long it remains activated after you push the keypad key to activate its second function. F0.At
: Exits the Function mode immediately after a key is pushed to activate its second function. (default) is displayed on the LCD. F .m F1/2/3.At : The Function mode remains activated for the selected pe-
riod after a key is pushed to activate its second function.
: The Function mode remains activated until [FUNC](M) is pushed again, even after a key is pushed to activate its second function. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 40 10 SET MODES D LCD backlight Selects the LCD backlight function. LIG.OF LIG.ON LIG.At
: Turns the backlight function OFF.
: Lights continuously while the transceiver is ON.
: Turns ON when an operation occurs, and turns OFF after 5 sec. (default) D TX permission Selects whether or not to allow transmitting. tX .OF : Inhibits transmitting. (Receive only) tX .ON
: Allows transmitting. (default) D Weather alert Turns the Weather Alert function ON or OFF. (p. 19) U.S.A. version only
(default: OFF) D VOX gain Sets the VOX gain to between 1 and 10. Higher values make the VOX function more sensitive to your voice. To turn the VOX function OFF, select VOX.OF.
(default: VOX.05) NOTE: Set the microphone gain before setting the VOX gain. See page 52 for details of the VOX function. D Microphone gain Sets the microphone gain to between 1 and 4 to suit your preference. Higher values make the microphone more sensi-
tive to your voice.
(default: mic.2) NOTE: When using the VOX function, we recommend setting the microphone gain to 3. However, you can adjust it to suit your operating environment (including your head-
set performance). 41 D VOX delay Sets the VOX Delay to between VXd.05 (0.5 sec.), VXd.10
(1 sec.), VXd.15 (1.5 sec.), VXd.20 (2 sec.), VXd.25 (2.5 sec.) and VXd.30 (3 sec.). The VOX Delay is the amount of time the transmitter stays ON after you stop speaking.
(default: VXd.10) D VOX time-out timer Sets the VOX time-out timer to between 1, 2, 3, 4, 5, 10 and 15 min. to prevent accidental prolonged transmission for the VOX function. To turn the function OFF, select Vto.OF.
(default: Vto.03) SET MODES 10 D DTMF TX key Selects the method to transmit a DTMF code sequence. While pushing and holding [PTT], push one of the keys,
[0] to [9], [MONI](A), [](B), [](C), [VFO/MR/CALL](D),
[M](E),and [# ENT](F). dmt.k
: Transmits the appropriate DTMF code assigned to the key.
(default)
: Transmits the programmed DTMF code sequence in the DTMF memory channel assigned to the key.
: No DTMF code can be transmitted. However, while pushing and holding [PTT], push either the [] or []
to transmit a 1750 Hz tone burst signal. dmt.m dmt.t D Operating mode Set the operating mode to FM or FM-N. The operating mode is determined by the modulation of the radio signals.
(default: W/n. W) FM mode FM-N mode 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 42 10 SET MODES Initial Set mode programming The Initial Set mode can be accessed at power ON and al-
lows you to set seldom-changed settings, to suit your prefer-
ence and operating style. D Initial Set mode operation q While pushing and holding [] and [], turn the power ON to enter the Initial Set mode. w Push [] or [] to select the desired item. e Rotate [VOL] to select the option or value. r To exit the Initial Set mode, push [# ENT]. Key-touch beep (p. 44) Time-out timer (p. 44) Auto repeater* (p. 44) Auto power-OFF (p. 44) Lockout (p. 45) Auto low power (p. 47)
: Push
: Push Battery protection function (p. 47)
*Appears for only the U.S.A. version transceivers. Squelch delay (p. 45) DTMF speed (p. 45) Dial assignment (p. 45) Microphone simple mode (p. 47) Select speed (p. 46) Power save (p. 46) LCD contrast (p. 46) Display type (p. 46) 43 Initial Set mode items D Key-touch beep Turns the key-touch beep ON (the beep level 1 to 3) or OFF. When changing the beep level, beeps sound at the level.
(default: bEP. 2) D Time-out timer To prevent accidental prolonged transmission, the trans-
ceiver has a time-out timer. This function cuts transmission OFF after 130 min. of continuous transmission. To turn the function OFF, select tot.OF.
: Turns the function OFF. (default) tot.OF
: If continuous transmission exceeds the selected period, tot. 130 the transmission will be cut off. SET MODES 10 U.S.A. version only D Auto repeater The Auto Repeater function automatically turns ON or OFF the duplex operation and the tone encoder. The offset and the repeater tone are not changed by the function. Reset these settings, if necessary. RPt.OF RPt.R1 RPt.R2
: Turns the function OFF.
: Activates for only duplex. (default)
: Activates for both duplex and tone. D Auto power-OFF The transceiver can be set to beep and automatically turn OFF, when no key operation occurs during a specified period. POF.OF POF.30/1H/2H : The transceiver is automatically turned OFF when
: Turns the function OFF. (default) no operation occurs during the selected period. NOTE: The setting is maintained even after the trans-
ceiver is turned OFF by the auto power-OFF function. To cancel the function, select POF.OF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 44 10 SET MODES D Lockout Selects the lockout type between repeater, busy and OFF. RLO.OF RLO.RP
: Turns the function OFF (default).
: The repeater lockout function inhibits transmitting when the channel is busy, except while receiving a signal that includes a matched tone.
: The busy lockout function inhibits transmitting while re-
ceiving a signal. RLO.bU D DTMF speed Selects a desired DTMF transfer speed. dtd. 1 dtd. 2 dtd. 3 dtd. 5
(cps=characters per second)
: 100 msec. interval; 5.0 cps rate (default)
: 200 msec. interval; 2.5 cps rate
: 300 msec. interval; 1.6 cps rate
: 500 msec. interval; 1.0 cps rate D Squelch delay Sets the squelch delay between short and long. The delay prevents the squelch from repeatedly opening and closing while receiving the same signal. Sqd. S Sqd. L
: Sets the squelch delay to short (default).
: Sets the squelch delay to long. D Dial assignment Selects whether or not to use [VOL] as a tuning control in-
stead of [] and []. When [VOL] functions as a tuning con-
trol, [] and [] function as volume controls. tOP.VO tOP.dI
: Audio volume control (default)
: Tuning dial
[VOL] and []/[] function as described below, depend-
ing on the option. Option tOP.VO tOP.di
[VOL]
Volume control Tuning control
Tuning controls Volume controls 45 D Display type Selects the display type for memory mode operation.
: Displays the programmed frequency. (default) dSP.FR dSP.CH
: Displays the memory channel number. Operable func-
tions, configurable items in the Set mode, and select-
able modes will be restricted.
: Displays the channel name. If no memory name is pro-
grammed, the programmed frequency will be displayed. dSP.nm SET MODES 10 D Power save The power save function allows you conserve battery life by selecting the duty cycle of the receiver. Select the ratio of the power save time to the standby time. To turn the function OFF, select PS.OF. PS.OF PS. 2 PS. 8 PS.16 PS.At
: Turns the function OFF.
: Sets the duty cycle to 1:2.
: Sets the duty cycle to 1:8.
: Sets the duty cycle to 1:16.
: Automatically sets the duty cycle. (default) D LCD contrast Selects the LCD contrast. Lcd.LO Lcd.At
: Sets the contrast to low.
: Sets the contrast to high. However, if the transceiver is exposed to high temperatures, it automatically sets the contrast to low. (default) D Select speed The tuning speed acceleration automatically speeds up the tuning speed when rotating [VOL] rapidly. SS. m SS. At
: Turns the tuning speed acceleration OFF.
: Turns the tuning speed acceleration ON. (default) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 46 10 SET MODES D Microphone simple mode Microphone simple mode is used to assign the essential opera-
tions to the four switches (S1 to S4) on the remote control unit. mS .Sm S1 S2 S3 S4 Selects the Call channel. Turns the monitor function ON or OFF. Selects memory channel 0. Selects memory channel 1. mS .n1 (default) S1 S2 S3 S4 Toggles the VFO mode and the memory mode. Selects the Call channel. Frequency or memory channel UP. Frequency or memory channel DOWN. mS .n2 S1 S2 S3 S4 Toggles the VFO mode and the memory mode. Turns the monitor function ON or OFF. Frequency or memory channel UP. Frequency or memory channel DOWN. User remote control unit The below circuit is for reference only. 2.7kW 6.8kW 15kW 33kW S1 S2 S3 S4 to the [SP] jack REMOTE 3.5(d) mm GND SP
EXTERNAL SPEAKER Rated input 700 mW (8 W)
47 D Battery protection When the battery voltage decreases, the battery protection function automatically turns the transceiver OFF. Select the function according to your battery type. bAt.OF
(default: differs depending on the version)
: Turns the function OFF. Select when you use the BP-263 battery case.
: Select when you use the BP-264 Ni-MH battery pack.
: Select when you use the BP-265 Li-Ion battery pack. bAt.nm bAt.LI NOTE: BE SURE to select an appropriate option accord-
ing to your battery type. D Auto low power Turns the auto low power function ON or OFF. When the temperature goes below 0C (+32F), the function automatically sets the output power to low. In that case, the transmit power selections (Hi/Mid) are also disabled.
(default: ALP.OF) Cloning operation Cloning allows you to quickly and easily transfer the programmed contents from one transceiver to another. D Transceiver-to-transceiver cloning q Turn the transceivers power OFF, and then connect an optional OPC-474 cloning cable to the [SP] jacks of the master transceiver and the sub transceiver. The master transceiver is used to send data to the sub trans-
ceiver. Master transceiver Sub transceiver w While pushing [FUNC](M) and [], turn the master trans-
ceiver ON to enter the cloning mode. CLONE appears CLONING 11 e Turn the sub transceiver ON. r Push [PTT] on the master transceiver. CL Out appears on the master transceivers display, and the signal indicator shows the data is being transferred to the sub transceiver. CL In appears on the sub transceivers display, and the signal indicator shows the data is being received from the master transceiver. t When cloning is finished, turn both the transceivers OFF. Then turn them ON again to exit the cloning mode. NOTE: DO NOT push [PTT] on the sub transceiver dur-
ing cloning. This will cause a cloning error. D Cloning using a PC The CS-V80 cloning software is also used to clone/edit con-
tents with a PC (for Microsoft Windows 2000/XP or Win-
dows Vista) using ICF format files. Refer to the INSTRUCTIONS and the Help file that come with the CS-V80, for details. OPC-478UC
(USB type) to USB port OPC-478
(RS-232C type) to RS-232C port PC Transceiver 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 48 12 RESETTING Resetting The LCD may occasionally display erroneous infor-
mation (e.g. when first applying power). This may be caused externally by static electricity or by other factors. If this problem occurs, turn power OFF. After waiting a few seconds, turn power ON again. If the problem per-
sists, perform either or both of the procedures below. D Partial reset If you want to reset the operating conditions (VFO fre-
quency, VFO settings, and Set modes contents) with-
out clearing the memory contents, use the partial reset. q Push and hold [
w While pushing and holding [VFO/MR/CALL], push and
] for 1 sec. to turn the power OFF. hold [
] for 1 sec. to turn the power ON. NOTE: No message appears on the display after the par-
tial reset is done. 49 D All reset The all reset clears all programming and returns all settings to their factory defaults. q Push and hold [
w While pushing and holding [MONI] and [VFO/MR/CALL],
] for 1 sec. to turn the power OFF. push and hold [
CLEAR appears when resetting the CPU.
] for 1 sec. to turn the power ON. CAUTION: The all reset returns all programmed contents to their default settings. TROUBLE SHOOTING 13 If your transceiver seems to be malfunctioning, please check the following points before sending it to a service center. PROBLEM POSSIBLE CAUSE SOLUTION The transceiver does not turn ON. No sound comes from the speaker. The battery is exhausted. The battery polarity is reversed. Loose connection of a battery pack/case. Volume is too low. An external speaker or a cloning cable is Charge the battery pack, or replace the batteries. Check the battery polarity. Clean battery terminals. Rotate [VOL] to adjust to a desired level. Check the external speaker connection or remove REF. pp. 1113 p. 13 p. 13 p. 14 Transmitting is impossible. connected to the [SP] jack. The battery is exhausted. TX permission is inhibited. Transmitting using the VOX function is impossible. Contacting with another sta-
tion is impossible. The VOX gain is set to OFF or too low. The microphone gain is too low. A different tone or code is used for the tone/DTCS squelch. the cloning cable. Charge the battery pack, or replace the batteries. Set the TX permission setting to ON in the Set mode. Set the VOX gain to a suitable level. Set the microphone gain to a suitable level. Check the tone/DTCS by performing a tone scan. pp. 1113 p. 41 pp. 41, 53 p. 41 p. 34 Frequency cannot be set. The key lock function is activated. Push [FUNC](M), then push and hold [
p. 18 A programmed scan does not start. A memor y scan does not start. The memory mode, Call channel mode, or weather channel mode is selected.
(# ENT) for 1 sec. to cancel the key lock function. Push [VFO/MR/CALL] several times to select the p. 15 VFO mode. The memory mode, Call channel mode, or Push [VFO/MR/CALL] several times to select the p. 15 weather channel mode is selected. VFO mode. The same frequency has been programmed in the scan edge channels, XAXb. The VFO mode or Call channel mode is Program different frequencies in the scan edge p. 25 channels. Push [VFO/MR/CALL] several times to select the p. 15 selected. memory mode. Only one or no memory channel has been Program 2 or more memory channels. programmed. The displayed frequency is er-
roneous. The CPU has malfunctioned. External factors have caused a fault. Reset the transceiver. Remove and re-attach the battery pack/case. p. 25 p. 49 p. 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 50 14 OPTIONS BP-263 battery case Battery case for LR6 (AA) 6 alkaline batteries. BP-264 ni-mh battery pack 7.2 V/1400 mAh (Typ.) Ni-MH battery pack. Battery life: 13 hrs.
(approx.; FM, high power, Tx : Rx : Standby = 5:5:90) BP-265 li-ion battery pack 7.4 V/1900 mAh (Min.)/2000 mAh (Typ.) Lithium Ion battery pack. Battery life: 19 hrs. (approx.; FM, high power, Tx : Rx :
Standby = 5:5:90) BC-191 desktop charger+BC-123S ac adapter For rapid charging of the Ni-MH battery pack. An AC adapter may be supplied with the charger, depending on the version. Charging time: approx. 2 hours for the BP-264. BC-192 desktop charger+BC-147S ac adapter For regular charging of the Ni-MH battery pack. An AC adapter may be supplied with the charger, depending on the version. Charging time: approx. 16 hours for the BP-264. BC-193 desktop charger+BC-123S ac adapter For rapid charging of the Li-Ion battery pack. An AC adapter may be supplied with the charger, depending on the version. Charging time: approx. 2.5 hours for the BP-265. CP-23L cigarette lighter cable Allows charging of the battery packs through a 12 V cigarette lighter socket. (For only BC-191/BC-193) OPC-515L dc power cable Allows charging of the battery packs using a 12 V DC power source instead of the AC adapter. (For all chargers) FA-B2E vhf antenna The same antenna that is supplied with the transceiver. HM-153L earphone-mirophone Ideal for hands-free operation: clip the HM-153L (with inte-
grated PTT switch) to your lapel or breast pocket. HM-158L/HM-159L speaker-mirophone Combination speaker-microphone that provides convenient operation while hanging the transceiver on your belt.
: Ear hook type
: Neck & arm type
: Throat microphone HS-94/HS-95/HS-97 headset+OPC-2004 plug adapter cable HS-94 HS-95 HS-97 OPC-2004 : Allows you to connect the HS-94/HS-95/HS-97 to the transceiver. After connecting, the VOX function can be used. CS-V80 cloning software+OPC-478/OPC-478UC cloning cable Provides quick and easy programming of such settings as memory channels and Set modes contents. OPC-474 cloning cable For transceiver-to-transceiver cloning. MB-124 belt clip Exclusive alligator-type belt clip. 51 Some options may not be available in some countries. Please ask your dealer for details. OPTIONS 14 VOX function The transceiver has a VOX function, which allows hands-free operation. An optional HS-94, HS-95 or HS-97 headset and the OPC-2004 plug adapter cable are also required for operation. The VOX (voice operated transmission) function starts transmis-
sion when you speak into the microphone, without needing to push [PTT]; then, automatically returns to reception when you stop speaking. D Optional unit connection q Push and hold [
w Remove the jack cover. (p. 2) e Connect the optional HS-94, HS-95 or HS-97 and
] for 1 sec. to turn the power OFF. OPC-2004, as illustrated below. OPC-2004 HS-94 D Turning the VOX function ON or OFF q Connect an optional headset and plug adapter cable to the transceiver, and then turn the power ON. w Push [FUNC](M), and then [VOX](2) to turn the VOX func-
tion ON or OFF. VOX appears when the VOX function is ON. NOTE:
When using the VOX function, adjust the microphone gain and the VOX-related settings (p. 53) to suit your operating environment (including your headset performance). Set the microphone gain before setting the VOX gain in the Set mode (p. 41). We recommend setting the micro-
phone gain to 3. When the TX permission is set to OFF in the Set mode, you cannot transmit using the VOX function. (p. 41) w e q
Appears 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 52 14 OPTIONS D VOX-related settings The VOX gain, the VOX delay, and the VOX time-out timer can be set in the Set mode. q Connect an optional headset and plug adapter cable to the transceiver, and then turn the power ON. w Push [FUNC](M), and then [VOX](2) to turn the VOX func-
tion ON. e Push [FUNC](M), and then [SET](8) to enter the Set mode. r Push [] or [] to select the VOX gain (VOX), the VOX delay (VXd), or the VOX time-out timer (Vto) item. t Rotate [VOL] to select a desired option. y Push [# ENT] to exit the Set mode. The VOX function does not activate transmission while in the Set mode. VOX gain The VOX gain level can be adjusted between 1 (minimum) and 10 (maximum), or turned OFF. Higher values make the VOX function more sensitive to your voice.
(default: VOX.05) The VOX function is turned OFF. The VOX gain is set to 10 (maximum). While speaking into the head-
set microphone, adjust the VOX gain until On continu-
ously appears on the LCD. Appears 53 If On is intermittent, be sure the VOX delay is set long enough to allow normal pauses in speech, but keep the VOX ON until you finish speaking. CONVENIENT!
While transmitting using the VOX function, you can adjust the VOX gain simply by rotating [DIAL]. VOX delay Sets the VOX delay to between 0.5 and 3.0 sec. (in 0.5 sec. steps). The VOX delay is the amount of time the transmitter stays ON after you stop speaking.
(default: VXd.10) The VOX delay is set to 1 sec. The VOX delay is set to 3 sec. VOX time-out timer Sets the VOX time-out timer to between 1, 2, 3, 4, 5, 10 and 15 min. to prevent accidental prolonged transmission for the VOX function. To turn the function OFF, select Vto.OF.
(default: Vto.03) D General Frequency coverage
(unit: MHz) Version U.S.A. AUS CHN EXP EUR UK KOR TX 144148 136174 144146 RX 136174 136174 144146 Mode Number of memory channels
: FM, FM-N
: 207 Usable temperature range Tuning steps
(incl. 6 scan edges and 1 Call channel)
: 20C to +60C; 4F to +140F
: 5, 10, 12.5, 15, 20, 25, 30 and 50 kHz
: 2.5 ppm
(20C to +60C; 4F to +140F)
: Icom specified battery pack/case Transmit at 5.5 W (High) at 2.5 W (Mid.) at 0.5 W (Low) Receive standby Frequency stability Power supply Current drain (at 7.2 V DC: typical) Antenna connector Dimensions
(projections not included) Weight (approx.)
(without battery pack/case and ant.) : 140 g; 4.9 oz
: 1.4 A 0.9 A 0.6 A
: 65 mA 20 mA 310 mA (internal speaker) 180mA (external speaker)
: BNC (50 W)
: 58(W)112(H)30(D) mm;
2932(W)41332(H)1316(D) in power save max. audio SPECIFICATIONS 15 D Transmitter Modulation system Output power (at 7.2 V DC) Max. frequency deviation Spurious emissions External mic. connector
: Variable reactance freq. modulation
: High 5.5 W, Mid. 2.5 W, Low 0.5 W.
: FM (wide) 5.0 kHz FM (narrow) 2.5 kHz
: Less than 60 dBc
: 3-conductor 2.5 (d) mm (110)/2.2 k D Receiver
: Double-conversion superheterodyne Receive system
: 1st: 21.7 MHz, 2nd: 450 kHz Intermediate frequencies Sensitivity (at 12 dB SINAD)
: 0.14 V typ. Squelch sensitivity (threshold) : 0.1 V typ. Selectivity
: FM (wide) 70 dB typ. FM (narrow) 50 dB typ. Spurious and image rejection : 75 dB typ. Intermodulation
: FM (wide) 70 dB typ. FM (narrow) 65 dB typ. Audio output power (at 10% distortion) External speaker connector : 3-conductor 3.5(d) mm; (18)/8
: 0.75 W typ. with a 16 load
: 0.45 W typ. with a 8 load Internal speaker External speaker All stated specifications are subject to change without notice or obligation. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 54 16 CE IMPORTANT When transmitting with a portable radio, hold the radio in a vertical position with its microphone 2.5 to 5 centimetres from your head and body. If you wear a portable two-way radio on your body, ensure that the antenna is at least 2.5 centimetres from your body when transmitting. CE Versions of the IC-V80E which display the CE symbol on the serial number label, comply with the essential requirements of the European Radio and Telecommunication Ter-
minal Directive 1999/5/EC. This warning symbol indicates that this equip-
ment operates in non-harmonised frequency bands and/or may be subject to licensing con-
ditions in the country of use. Be sure to check that you have the correct version of this radio or the correct programming of this radio, to comply with national licensing requirements. List of Country codes (ISO 3166-1) Country Codes Austria AT 1 Belgium BE 2 Bulgaria BG 3 Croatia HR 4 Czech Republic CZ 5 CY Cyprus 6 DK Denmark 7 Estonia EE 8 FI 9 Finland FR 10 France DE 11 Germany GR 12 Greece 13 Hungary HU IS 14 IE 15 IT 16 17 LV Iceland Ireland Italy Latvia Codes Country LI Liechtenstein LT Lithuania LU Luxembourg MT Malta NL Netherlands NO Norway PL Poland PT Portugal RO Romania SK Slovakia SI Slovenia EP Spain SE Sweden CH Switzerland Turkey TR United Kingdom GB 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 55 DECLARATION OF CONFORMITY We Icom Inc. Japan 1-1-32, Kamiminami, Hirano-ku Osaka 547-0003, Japan Declare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunications Terminal Equipment Directive, 1999/5/EC, and that any applicable Essential Test Suite measurements have been performed. Kind of equipment:
VHF TRANSCEIVER Type-designation: iV80E Version (where applicable):
Dsseldorf 16th Oct. 2009 Place and date of issue Icom (Europe) GmbH Himmelgeister strae 100 D-40225 Dsseldorf Authorized representative name Y. Furukawa General Manager desinomrah gniwollof eht htiw ytimrofnoc no desab si ecnailpmoc sihT standards, specications or documents:
i) EN 301 489-1 v1.8.1 (Apr. 2008) ii) EN 301 489-15 v1.2.1 (Aug. 2002) iii) EN 301 783-2 v1.1.1 (Sep. 2000) iv) EN 60950-1 (2001): A11: 2004 Signature CE 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 56
#02 Europe
#12 Europe-21
#22 Europe-22
#32 Europe-23
#13 U.K.-01
#23 U.K.-02
#33 U.K.-03
<Intended Country of Use>
AT BE CY CZ DK EE FI FR DE GR HU IE IT LV LT LU MT NL PL PT SK SI ES SE GB IS LI NO CH BG RO TR HR
<Intended Country of Use>
AT BE CY CZ DK EE FI FR DE GR HU IE IT LV LT LU MT NL PL PT SK SI ES SE GB IS LI NO CH BG RO TR HR A-6795H-1EX-0a Printed in Japan 2009 Icom Inc. Printed on recycled paper with soy ink. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2009-11-20 | 136 ~ 174 | CSR - Scanning Receiver | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2009-11-20
|
||||
1 | Applicant's complete, legal business name |
ICOM Incorporated
|
||||
1 | FCC Registration Number (FRN) |
0005855366
|
||||
1 | Physical Address |
1-1-32 Kamiminami
|
||||
1 |
Osaka, N/A 547-0003
|
|||||
1 |
Japan
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
v******@ultratech-labs.com
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
AFJ
|
||||
1 | Equipment Product Code |
325400
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
A**** T********
|
||||
1 | Title |
General Manager
|
||||
1 | Telephone Number |
+8166********
|
||||
1 | Fax Number |
+8166********
|
||||
1 |
w******@icom.co.jp
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
UltraTech Engineering Labs Inc.
|
||||
1 | Name |
J******** C********
|
||||
1 | Physical Address |
3000 Bristol Circle
|
||||
1 |
Oakville, ON, L6H6G4
|
|||||
1 |
Canada
|
|||||
1 | Telephone Number |
905-8********
|
||||
1 | Fax Number |
905-8********
|
||||
1 |
j******@ultratech-labs.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | CSR - Scanning Receiver | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | VHF Transceiver | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
UltraTech Engineering Labs Inc.
|
||||
1 | Name |
T**** L******
|
||||
1 | Telephone Number |
905-8********
|
||||
1 | Fax Number |
905-8********
|
||||
1 |
t******@ultratech-labs.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15B | 136.00000000 | 174.00000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC