all | frequencies |
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Antenna Specs | Users Manual | 109.12 KiB | / January 05 2015 | |||
1 |
|
User Manual 1 | Users Manual | 2.32 MiB | / January 05 2015 | |||
1 |
|
User Manual 2 | Users Manual | 514.56 KiB | / January 05 2015 | |||
1 |
|
User Manual 3 | Users Manual | 169.49 KiB | / January 05 2015 | |||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | Attestation Statements | |||||||
1 | External Photos | / January 05 2015 | ||||||
1 | Internal Photos | / January 05 2015 | ||||||
1 | ID Label/Location Info | |||||||
1 | Attestation Statements | |||||||
1 | Attestation Statements | |||||||
1 | Attestation Statements | |||||||
1 | RF Exposure Info | |||||||
1 | RF Exposure Info | |||||||
1 | RF Exposure Info | |||||||
1 | RF Exposure Info | |||||||
1 | RF Exposure Info | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | Antenna Specs | Users Manual | 109.12 KiB | / January 05 2015 |
FA-SC61VC Antenna Cutting Chart Antenna cap 136 MHz 140 MHz 145 MHz 150 MHz 155 MHz 160 MHz 165 MHz 170 MHz 175 MHz 0 Thank you for purchasing the FA-SC61VC VHF ANTENNA. Please read these instructions thoroughly before using the FA-SC61VC. FA-SC61VC The optimum bandwidth is 3%
of the tuned frequency. For optimum performance tune to the center transmit frequency of the radio. Cutting Instructions q Align the bottom of the anten-
na onto the 0 position of the cutting guide diagram at left. w Mark the antenna at the length corresponding to the desired to be tuned. frequency e Cut the antenna to the marked length. Use a wire cutter that can cut at least 1.2 mm (d) of piano wire. r Apply adhesive to the top of the antenna and attach the supplied antenna cap. Use of Cemedine Co. Super-X No. 8008 black
(Icom number:
8950002910) or similar is recommended. parts NOTE:
Antenna cap must be inser ted after cutting the element otherwise water immersion makes the element damaged. Center frequency
(MHz) 136 140 145 150 155 160 165 170 175 Length
(mm) 174*
169 163 157 151 146 141 137 133
The antenna can be used at its or iginal length for this frequency. No tuning (cutting) is necessary. CAUTION:
Making antenna cuts at other than the prescribed lengths specified could void the user's authority to operate the equipment. A-6532K-1EX-w Printed in Japan 2006-2009 Icom Inc.
1 | User Manual 1 | Users Manual | 2.32 MiB | / January 05 2015 |
0 a ICOM et OPERATING GUIDE VHF TRANSCEIVERS ICFIOOOD UHF TRANSCEIVERS ICF2OO00D The photo shows Icom Inc. the UHF transceivers. IMPORTANT We appreciate you choosing Icom for your communication READ ALL INSTRUCTIONS carefully and completely needs. before using the transceiver. The MDC 1200 signaling system is built into your IC-F1000D/ SAVE THIS OPERATING GUIDE This operating IC-F2000D series transceiver. guide contains important operating instructions for:
*IC-F1000D VHF TRANSCEIVERS
*IC-F2000D UHF TRANSCEIVERS Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incor-
porated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. All other products or brands are registered trademarks or trademarks of their respective holders. TABLE OF CONTENTS IMPORTANT... TABLE OF CONTENTS.... 1 PANEL DESCRIPTION... Front, top and side panel MLED indicator.
@ Programmable function keys . 2 BASIC OPERATION..
@ Selecting a channel
@ Receiving and transmitting ..
@ Emergency Call i Lone Worker Emergency Call. Man Down Emergency Call... Motion Detection Emergency Call Setting the Beep function Setting the Beep level . Setting the Ringer level ... Setting the microphone gain . Setting the squelch level
@ Output power level selection
@ Priority A channel selection .. 4 IDAS OPERATION 3 MDC 1200 SYSTEM OPERATION
@ MDC 1200 system operation..
@ Receiving a call . Transmitting a cal
@ IDAS operation
@ IDAS-Trunk operation ..
@ Receiving a call ..
@ Transmitting a call
@ Position data transmission ...
@ Status message transmission . Encryption function .... a a |
Hi Front, top and side panels
@ RoTARY
/ SELECTOR a @ voLumE CONTROL [VOL]
ANTENNA CONNECTOR
@.eD Da INDICATOR = [Emer]
Speaker orm == @ SPEAKER-
SWITCH = MICROPHONE ier] SS JACK 5 ___!Il__ microphone PANEL DESCRIPTION
@ ROTARY SELECTOR Rotate to select the preset memory channels.
@ VOLUME CONTROL [VOL]
Rotate to turn the power ON or OFF and to adjust the audio level. DEALER-ASSIGNABLE KEY [Emer]
A desired function can be programmed by your dealer.
@ SPEAKER-MICROPHONE JACK Connect optional equipment. GY NOTE: After turning OFF the transceiver, connect or dis-
Z connect the optional equipment. Jack cover
( NOTE: Attach the jack cover when
| optional equipment is not used. DEALER-ASSIGNABLE KEYS
[Upper] , [Lower]
Desired functions can be independently programmed by your dealer.
@ PTT SWITCH [PTT]
Hold down to transmit, release to receive. PANEL DESCRIPTION 1
@ LED INDICATOR Lights red while transmitting. Lights green while receiving a signal, or when the squelch is open. Lights or blinks orange when the matched 2-Tone or 5-Tone is received, depending on the presetting. You should charge the battery when the indicator slow-
ly blinks. You must charge the battery when the indicator blinks fast. ANTENNA CONNECTOR Connects the supplied antenna.
PANEL DESCRIPTION LED indicator The LED indicator indicates the status of various parameters of the transceiver as follows: * Receiving
(Reference: R=Red, G=Green, O=Orange) ooo pi
* Cloning (reading or writing data) * Low Battery 2 (You must charge the battery.) ~
6] [es] [e] [Ss] fe) [Ss] [4] [6] f~ G] [e G ~
* Cloning Error (if cloning fails) " * Low Battery 1 (You should charge the battery.) BY G]R]C)RIS IRCA] CTR] GRIST Sy] G Inh, Blank CH, Unlocked (when you cannot use the channel) *When turning ON the power ~
ROTA] OTR]OTRIOTR|OTR)OTROTRIO] _ RIOTS] [Ros i
+ TX Low Battery 2 (while transmitting) *Calling ~
R R R RA) ft ] fo] fe o] [fo] [oy
* TX Low Battery 1 (while transmitting) " * Audible R Let Cm
* Transmitting * Lockout, TX Inh, TOT (when transmit is inhibited)
* Call LED=ON (when receiving a matched 2-Tone or 5-Tone) * Successful 3 c os c
* Call LED=Blink (when receiving a matched 2-Tone or 5-Tone) Failed, Error Oo] fo a =
* Scanning * Emergency, Siren G G clojR] [cfofR] [clojR] [cjofR] j~
7 |
a |
1 PANEL DESCRIPTION i Programmable function keys The following functions can be assigned to
[Emer], [Upper], and [Lower]. Consult your Icom dealer or system operator for details con-
cerning your transceivers programming. SCAN START/STOP Push to start and cancel a scan.
* When a scan is started with the Power ON Scan or Auto-
matic scan function, push this key to cancel it. The can-
celled scan resumes after a set time period. PRIORITY A CHANNEL, PRIORITY B CHANNEL Push to select the Priority A or Priority B channel. PRIORITY A CHANNEL (REWRITE), PRIORITY B CHANNEL (REWRITE) Push to select the Priority A or Priority B channel.
> Hold down [Prio A (Rewrite)] or [Prio B (Rewrite)] to as-
sign the operating channel to Priority A or Priority B chan-
nel, respectively. MEMORY CHANNELS 1, 2, 3, 4 Push to directly select memory channel 1, 2, 3 or 4, if pro-
grammed. MONI// only for the LMR mode //
Hold down to cancel the CTCSS (DTCS) or 2-Tone mute. The transceiver enters Audible mode. Push to turn OFF the function. MONI (Audi) / only for the PMR mode //
Hold down to cancel the CTCSS (DTCS) or 5-Tone mute. The transceiver enters Audible mode. Push or hold down to activate one or two functions if pro-
grammed. PANEL DESCRIPTION 1 LOCK Hold down this key to lock all programmable keys except the followings:
[Moni], [Lock], [Emer], [Surveillance], [Siren], [Lone Worker], and [Shift]. LONE WORKER Hold down to turn ON the Lone Worker Function. Push to turn OFF the Function.
* If no operation occurs for a set time period, the trans-
ceiver automatically enters the emergency mode. HIGH/LOW Push to select the transmit output power temporarily or permanently, depending on the presetting.
N 1 PANEL DESCRIPTION TALK AROUND Push to turn the Talk Around function ON or OFF. The Talk Around function equalizes the transmit frequen-
cy to the receive frequency for transceiver-to-transceiver communication. WIDE/NARROW Push to toggle the channel passband width between wide and narrow. DTMF AUTODIAL Push to transmit the preprogrammed DTMF code. CALL Push to transmit a 2-Tone or 5-Tone in the operating chan-
nel. CALL A (CODE 1)/CODE B (CODE 2) 4 only for the LMR model //
Push to transmit a 2-Tone, that is programmed in channel 1 (Code A) or channel 2 (Code B). CALL A (CODE 30/CODE B (CODE29) 4 only for the PMR model //
Push to transmit a 5-Tone as a station code, that is pro-
grammed in channel 30 (Code A) or channel 29 (Code B). EMERGENCY Hold down during the Emer SW ON timer period to turn ON the Emergency function.
* After the Start or Repeat timer period ends, an Emer-
gency call is automatically transmitted once, or repeat-
edly, depending on the presetting. Hold down during the Emer SW OFF timer period to can-
cel the Emergency function, before transmitting an Emer-
gency call. SURVEILLANCE Hold down to turn ON the Surveillance function. Push to turn OFF the function.
* When this function is ON and a signal is received, a beep does not sound and the LED does not light, even if you push any key. SIREN Hold down to emit a siren sound.
* This function may use for situations other than an emer-
gency alert, such as a security alarm.
* Turning OFF the transceiver power to stop the siren sound. PANEL DESCRIPTION 1 4 |
1 PANEL DESCRIPTION ENCRYPTION Push to turn the Voice Encryption function ON or OFF while operating in the digital mode. ANNOUNCE Push to turn the Channel Announce function ON or OFF. Z NOTE:
Z When the Beep function (p.16) is OFF, the operating chan-
Z nel is not announced, regardless of this setting. Hf Selecting a channel There are several types of channel selections. Methods may differ, depending on the presetting. Consult your dealer for details. To select the desired operating channel:
Rotate [ROTARY SELECTOR].
> Push one of [MR-CH 1] to [MR-CH 4]. Push [Prio A], [Prio B], [Prio A (Rewrite)] or [Prio B (Re-
write)]. AUTOMATIC SCAN TYPE:
Channel setting is not necessary for this scan type. When turning ON the power, the transceiver automatically starts scanning. Scanning stops when a signal is received. 2 BASIC OPERATION Hf Receiving and transmitting Y CAUTION:
Z Attach an antenna before transmitting. Z Transmitting without an antenna may damage the trans-
Z ceiver. Receiving:
@ Rotate [VOL] to turn ON the power.
@ Rotate [ROTARY SELECTOR], or push one of the memo-
ry channel keys, [MR-CH1] to [MR-CH4], to select a chan-
nel.
@ When receiving a call, adjust the audio output level to a comfortable listening level. Transmitting:
Wait until the channel is clear to avoid interference.
@ While holding down [PTT], speak at a normal voice level.
@ Release [PTT] to receive. ZG IMPORTANT: To maximize the readability of your signal:
G 1. Alter pushing [PTT], pause briefly before you start ZY speaking. Go. Hold the microphone 5 to 10 cm (2 to 4 inches) from Z your mouth, then speak at a normal voice level. 2 BASIC OPERATION Transmitting notes
* Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions:
- The channel is busy. However, depending on the presettings, you can transmit when the call includes an unmatched (or matched) CTC-
SS (DTCS) tone.
- The selected channel is a receive only channel.
* Time-out timer If continuous transmission exceeds the preprogrammed time-out timer limit, transmission is cut off.
* Penalty timer The time-out timer cuts off transmission, further transmi:
sion is inhibited for the preprogrammed penalty timer peri-
od.
*PTTID call The transceiver automatically sends the ID code (5-tone, DTMF, BIIS, MDC system or IDAS operations) when [PTT] is pushed (beginning of the transmission) and/or released
(end of transmission), depending on the presetting. DTMF transmission If the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is usable. Push [DTMF Autodial] to transmit the DTMF code. Receiving a Stun, Kill and Revive call The dispatcher can send a 2-Tone or 5-Tone that will stun, kill or revive your transceiver. When the Stun command is received, a beep sounds*, and the transceiver becomes unusable. Receiving a Revive com-
mand is necessary to operate the transceiver again in this case. When the Kill command is received, a beep sounds", and the transceiver becomes unusable (the transceiver switches to the cloning required condition). Cloning the transceiver is necessary to operate the transceiver again in this case.
* Depending on the presetting. Ask your dealer for details. Hf Emergency Call When pushing [Emergency] for the set time period", the transceiver transmits an emergency signal once, or repeat-
edly, on the specified emergency channel. The transceiver automatically transmits a repeat emergen-
cy signal until it receives an acknowledgement signal, or you turn OFF the transceiver power. When no emergency channel is specified, it transmits the signal on the previously selected channel. If you want to cancel the emergency call, hold down [Emer-
gency] again before transmitting the call. If your transceiver is programmed for Silent operation, you can transmit an Emergency call without the beep sounding and the LED indicator lighting. G \MPORTANT: It is recommended to set an emergency Z channel individually to provide the certain emergency call Z operation. BASIC OPERATION 2 ZY NOTE:
Z Depending on the presetting, the following functions are Z automatically activated. Ask your dealer for details.
* Auto TX function After an emergency call transmission, the transceiver trans-
mits the audio from the microphone for a set time period.
* Auto RX function After the emergency call transmission, the transceiver stands by in the audible mode for the set time period.
* Depending on the presetting. Ask your dealer for details. 2 BASIC OPERATION i Lone Worker Emergency Call When the Lone Worker function is ON, and if no operation occurs for a set time period, the transceiver automatical-
ly enters the emergency mode. Then the countdown for the emergency call transmission starts. After a set time period* has passed, an emergency call is au-
tomatically transmitted once, or repeatedly. If the user operates the transceiver before the call is trans-
mitted, the transceiver exits the emergency mode, and the emergency call is cancelled. To turn ON the function, see page 6. Hf Man Down Emergency Call This function may or may not be available, depending on the presetting. When the transceiver has been left in a horizontal position for a set time period", the transceiver enters the emergency mode, and then a countdown starts. After a set time period has passed, an emergency call is au-
tomatically transmitted once, or repeatedly". If the transceiver is placed in a vertical position before the first transmission, the transceiver exits the emergency mode, and the emergency call is cancelled. Hf Motion Detection Emergency Call This function may or may not be available, depending on the presetting. If the acceleration sensor detects the user continuous-
ly moves for the set timer period and at the set speed, the transceiver enters the emergency mode, and then the count-
down starts. After a set time period* has passed, an emergency call is au-
tomatically transmitted once, or repeatedly. Once the countdown starts, you cannot cancel the emergen-
cy call.
* Depending on the presetting. Ask your dealer for details. Hf Setting the Beep function The Beep function can be turned ON or OFF. When it is OFF, the channel announcement is also turned OFF. Y NOTE:
Grou should turn ON the Beep function when you set the Z Beep level, the Ringer level, the microphone gain, and the ZG squelch level.
@Rotate [VOL] to turn the transceiver power OFF.
@Set [ROTARY SELECTOR] to any channel other than Channel 16.
@While holding down [Lower], rotate [VOL] to turn ON the power to enter the Beep level adjustment mode.
@Push [Lower] to turn the Beep function ON or OFF.
* When a beep sounds after pushing [Lower], the Beep function is ON. When no beep sounds after pushing [Lower], the Beep function is OFF. The transceiver stores the setting every time you change it.
* If desired, push [Upper] to adjust the Beep level. See page 17 for details.
@Rotate [VOL] to turn OFF the power to exit the Beep level adjustment mode. BASIC OPERATION 2
[ROTARY SELECTOR]
[Upper] 1
[Lower] @) 2 BASIC OPERATION Hi Setting the Beep level The Beep level is adjustable between 1 and 5, or 1 (linked) and 5 (linked). When a Linked option is selected, the beep audio level is adjustable by rotating [VOL].
@Rotate [VOL] to turn OFF the transceiver.
@Set [ROTARY SELECTOR] to any channel other than Channel 16.
@While holding down [Lower], rotate [VOL] to turn ON the power and enter the Beep level adjustment mode.
@Push [Upper] to change the Beep level.
* Repeatedly pushing [Upper] first selects 1 (lowest) to 5
(highest), and then selects the lowest linked level, 1 (Linked) to the highest, 5 (Linked). Repeatedly pushing [Upper] repeats the cycle. See the illustration on the right.
* The adjustable range is 1 to 5 or 1 (Linked) to 5 (Linked).
*A beep sounds every time you push [Upper]. Therefore, you can determine the current level setting by the increasing loud-
ness of the beep that sounds.
*To determine if you have selected a linked level, set [VOL] to minimum, then push [Upper] repeatedly, listening for the loud-
est beep (level 5). Pushing [Upper] once after the loudest beep will select 1 (Linked). Repeatedly push [Upper] to select the desired linked level.
@Rotate [VOL] to turn OFF the power to exit the Beep level adjustment mode. Z NOTE:
ZG ihis operation may not be selectable, depending on the G presetting, Ask your dealer for details. I _{VOL]
[Lower].!) cS cS 5 cS
G(Linked)) G@Ginkea))
@Wlinked)) eis Hi Setting the Ringer level The Ringer level can be adjusted between 1 and 5, or 1
(Linked) and 5 (Linked). When a Linked option is selected, the ringer audio level is adjustable by rotating [VOL].
@Rotate [VOL] to turn OFF the transceiver power.
@Set [ROTARY SELECTOR] to Channel 16.
@While holding down [Lower], rotate [VOL] to turn ON the power and enter the Ringer level adjustment mode.
@Push [Upper] to increase, or push [Lower] to decrease the Ringer level. Repeatedly pushing [Upper] first selects 1 (lowest) to 5
(highest), and then selects the lowest linked level, 1 (Linked) to the highest, 5 (Linked). Repeatedly pushing [Upper] or [Lower]
repeats the cycle. See the illustration on the right.
* The adjustable range is 1 to 5 or 1 (Linked) to 5 (Linked).
*A beep sounds after pushing [Upper]. Therefore, you can determine the current level setting by the increasing loudness of the beep that sounds.
*To determine if you have selected a linked level, set [VOL]
to minimum, then push [Upper] up to 10 times, listening for the loudest beep (level 5). Pushing [Upper] once after the loudest beep will select 1 (Linked). Repeatedly push [Upper]
or [Lower] to select the desired linked level.
@Rotate [VOL] to turn OFF the power to exit the Ringer level adjustment mode. BASIC OPERATION 2 NOTE:
This operation may not be selectable, depending on the presetting. Ask your dealer for details. WV Pushing Pushing
[Upper] [Lower]
[ROTARY SELECTOR]
4y__IvoL]
[Upper]
[Lower] ! k
-e) 2 BASIC OPERATION Hf Setting the microphone gain Adjust the microphone gain.
@Rotate [VOL] to turn the transceiver power OFF.
@Set [ROTARY SELECTOR] to Channel 16.
@While holding down [Upper], rotate [VOL] to turn ON the power and enter the microphone gain adjustment mode.
@Push [Upper] or to increase, or push [Lower] to decrease the microphone gain.
* The adjustable range is 1 (minimum) to 4 (maximum).
*A beep sounds after pushing [Upper] or [Lower]. An error beep sounds if you try to exceed the adjustable range.
@Rotate [VOL] to turn OFF the power to exit the microphone gain adjustment mode. GY NOTE:
ZG This operation may not be selectable, depending on the GZ presetting. Ask your dealer for details. Hi Setting the squelch level The squelch circuit mutes the received audio signal, de-
pending on the signal strength.
@Rotate [VOL] to turn the transceiver power OFF.
@Set [ROTARY SELECTOR] to any channel other than Channel 16.
@While holding down [Upper], rotate [VOL] to turn ON the power and enter the squelch level adjustment mode.
@Push [Upper] to increase the squelch level (tight squelch), or push [Lower] to decrease the squelch level (loose squelch).
* The adjustable range is 0 (loose squelch) to 9 (tight squelch).
*A beep sounds after pushing [Upper] or [Lower]. An error beep sounds if you try to exceed the adjustable range.
@Rotate [VOL] to turn OFF the power to exit the squelch level adjustment mode. GY NOTE:
ZYrris operation may not be selectable, depending on the Z presetting. Ask your dealer for details. Hf Output power level selection If the transceiver has [High/Low] assigned to it, the trans-
mit output power level can be selected, depending on the presetting. Push [High/Low] to select the transmit output power level.
* One beep sounds when Low 1 is selected.
* Two beeps sound when Low 2 is selected.
* Three beeps sound when High is selected. BASIC OPERATION 2 Hf Priority A channel selection When one of the following operations is performed, the trans-
ceiver automatically selects the Priority A channel.
* Turning the power ON The Priority A channel is selected each time the transceiver power is turned ON.
+ Auto reset The Priority A channel is selected when the Auto Reset timer ends. 3 MDC 1200 SYSTEM OPERATION Hi MDC 1200 system operation The MDC 1200 signaling system enhances your transceiver's capabilities. You can receive or transmit PTT ID and Emer-
gency calls. You can also receive Radio Check, Stun, and Revive calls. An additional feature of the MDC 1200 system included in Icom transceivers is called aliasing. Each transceiver on the system has a unique ID number. Aliasing is a substitute for this ID number and you can give an alphanumeric name for each station ID. Hf Receiving a call Receiving a PTT ID
@ When a PTT ID is received:
* Beeps sound.
@ Hold down [PTT] and speak into the microphone.
@ Release [PTT] to receive a response. Receiving an Emergency Call
@When an emergency call is received:
+ Beeps sound.
@Turn power OFF or change the channel to stop the beep. Receiving a Stun, Kill and Revive call The dispatcher can send a 2 or 5-tone signal that will stun, kill or revive your transceiver. When the Stun command is received, a beep sounds*, and the transceiver becomes unusable. Receiving a Revive command is necessary to operate the transceiver again in this case. When the Kill command is received, a beep sounds*, and the transceiver becomes unusable (the transceiver switches to the cloning required condition). Cloning the transceiver is nece-
ssary to operate the transceiver again in this case.
* Depending on the presetting. Ask your dealer for details. Hi Transmitting a call Transmitting a PTT ID
@Push [PTT] to make a call.
@Beeps sound, depending on the presetting.
@Your station ID will be transmitted when you push [PTT]
(at the beginning of transmission) or release it (at the end of transmission), depending on the presetting. MDC 1200 SYSTEM OPERATION 3 Transmitting an Emergency Call When holding down [Emergency] for a set time period, the emergency signal is transmitted once or repeatedly* on the emergency channel. When no emergency channel is speci-
fied, the signal is transmitted on the operating channel.
* When the Repeat Cancel function is ON, the transceiver cancels repeating after receiving an acknowledgement. When the Repeat Cancel function is OFF, the transceiver repeats calling according to the number of repeat cycles, even after receiv-
ing an acknowledgement. If you want to cancel the emergency call, hold down the key again before transmitting the call. You can transmit an emergency call without a beep emis-
sion, and the display indication, depending on the preset-
ting. (Silent operation) The transceiver can also be programmed to keep the micro-
phone open during an emergency call, allowing monitoring the situation. Ask your dealer for details. Z IMPORTANT: It is recommended to set an emergency G channel individually to provide the certain emergency call ZG operation.
= 4 IDAS OPERATION Hf IDAS operation The IC-F1000D series and IC-F2000D series provide Icom Digital Advanced System (IDAS) that meets the 6.25 kHz emission mask requirements for narrow band-
ing, and increases efficiency of channel allocation and use of spectrum. Y NOTE: During IDAS operation, BIIS 1200 and MDC G 1200 system operations are not available. Hf IDAS-Trunk operation The IDAS-Trunk system enables further effective channel management by sharing a minimum of channels with a large number of users. Rotate [ROTARY SELECTOR] to select the memory chan-
nel that is programmed in the IDAS-Trunk zone. SN NOTE: During IDAS-Trunk operation, you can receive G and transmit digital calls in the same way with the follo-
id it digital calls in th ith the foll 4 wing IDAS operation. WS Hf Receiving a call Receiving a Call Alert
@ When a Call Alert is received;
* The transceiver will automatically transmit the acknowledge-
ment.
* The LED indicator blinks orange.
* Beeps sound.
@ Hold down [PTT], then speak into the microphone.
@ Release [PTT] to receive a response. Y NOTE: The LED indicator or Beeps may differ, depending G on the presetting. Ask your dealer for details. Receiving a Stun, Kill or Revive If an individual call with Stun or Kill command is received
(RAN code matching is not necessary depending on the prese-
tting), the transceiver will automatically transmit the acknowle-
dgement, and then you cannot receive* or transmit.
* Depending on the received Stun command setting. When a Stun command is received;
* The transceiver cannot be operated until the individual call with Revive command is received (RAN code matching is not necessary depending on the presetting) or until the da-
ta cloning is performed.
* Even if [ROTARY SELECTOR] is changed, the transceiver will keep the same channel as the Stun command is recei-
ved.
= When a Kill command is received;
* The LED indicator alternately blinks red and green.
* The transceiver cannot be operated until the data cloning is performed. Ask your dealer for details. S Y NOTE: Depending on the presetting, the transceiver GY ignores the Stun, Revive and Kill commands, which Z are trom a non-specified station. SS Receiving a Remote Monitor or Radio Check Call If an individual call with Remote monitor or Radio check command is received (RAN code matching is not necess-
ary depending on the presetting), the transceiver will auto-
matically transmit. When a Remote monitor command is received;
The transceiver will automatically transmit the ack-
nowledgement, and then it transmits the microphone audio for the set time period. When a Radio check command is received;
The transceiver will automatically transmit the ack-
nowledgement. IDAS OPERATION 4 Hi Transmitting a call IDAS operation allows you to make a call to a specific station
(Individual call) or to a particular group (Talkgroup call). Other digital mode transceivers on the channel will not receive a call that does not match their individual or talkgroup ID and/or RAN (Radio Access Number) code. Transmitting an Emergency Call When [Emergency] is held down for the specified time period, the emergency signal (digital command) is transmitted once or repeatedly* on the specified emergency channel. When no emer-
gency channel is specified, the signal is transmitted on the opera-
ting channel.
*When the Repeat Cancel function is ON, the transceiver can-
cels repeating after receiving an acknowledgement. When the Repeat Cancel function is OFF, the transceiver re-
peats calling according to the number of repeat cycles, even after receiving an acknowledgement. Individual or Talkgroup call types of emergency calls can be pre-fixed. If the call type is not pre-fixed, the default or sele-
cted call type is used. If you want to cancel the emergency call, hold down
[Emergency] again before transmitting the call. If your transceiver is programmed for Silent operat-
ion, you can transmit an Emergency call without the beep sounding and the LED indicator lighting. The transceiver can also be programmed to keep the microphone open during an emergency call, allowing mo-
nitoring of the situation. Ask your dealer for details. IMPORTANT: It is recommended to set an emergen-
cy channel individually to provide the certain emerge-
ncy call operation. AV NOTE: The Digital Request Ack function is activated, the transceiver transmits the emergency call with the request to send back an acknowledgment. WVv IDAS OPERATION 4 Hf Position data transmission When an optional HM-171GPW or any other GPS receiver is connected to the transceiver, the position (longitude and latitude) data can be transmitted automatically when;
* After sending a Status Call
- Set the Send with Status Call item as Enable After sending an Emergency Call
- Set the Send with Emergency item as Enable.
* After sending a Voice Call
- Set the Send with Voice Call item as Enable:
Ask your dealer or system operator for connection details.
@ Status message transmission The status message can be transmitted automatically. The status message is transmitted when the transceiver is turned ON or OFF.
- Select a status message to be transmitted in Power ON Status or Power OFF Status item, respectively.
- Select a target station ID in Power Status ID. Encryption function The encryption function enables voice scrambling, which pro-
vides private digital communication between stations. Push [Encryption] to turn the encryption function ON or OFF. Count on us!
Icom Inc. 2014 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
1 | User Manual 2 | Users Manual | 514.56 KiB | / January 05 2015 |
OPTIONS D BATTERY PACKS BP-278/BP-279/BP-280 Battery pack Voltage BP-278 7.2 V BP-279 7.2 V BP-280 7.2 V battery pack Capacity 1130 mAh
(minimum) 1190 mAh
(typical) 1485 mAh
(minimum) 1570 mAh
(typical) 2280 mAh
(minimum) 2400 mhA
(typical) Battery life*
9 hours 12 hours 18 hours
* When the power save function is turned ON, and the operating periods are calculated under the following conditions. TX : RX : standby = 5 : 5 : 90 desktop charger + BC-123S ac adapter D CHARGERS BC-213 To rapid charge a single battery pack. BC-214 To rapid charge up to 6 battery packs. multi charger + BC-157S ac adapter cigarette lighter cable D DC CABLES CP-23L Use when charging the battery pack from a 12 V cigarette lighter socket. (Use with the BC-213) OPC-656 Use with a 13.8 V power source instead of the power adapter. (Use with the BC-214) dc power cable D ANTENNAS FA-SC25V/FA-SC55V/FA-SC62V/FA-SC63V vhf antennas FA-SC25V: 136150 MHz FA-SC55V: 150174 MHz FA-SC62V: 150160 MHz FA-SC63V: 155165 MHz FA-SC26VS/FA-SC27VS/FA-SC56VS/FA-SC57VS vhf stubby antennas FA-SC26VS: 136144 MHz FA-SC27VS: 142150 MHz FA-SC56VS: 150162 MHz FA-SC57VS: 160174 MHz FA-SC61VC FA-SC61VC: 136174 MHz FA-SC25U/FA-SC57U/FA-SC72U/FA-SC73US uhf antennas FA-SC25U: 400430 MHz FA-SC57U: 430470 MHz FA-SC72U: 470520 MHz FA-SC73US: 450490 MHz FA-SC26US FA-SC26US: 400450 MHz uhf stubby antenna vhf cut antenna uhf antenna FA-SC01U/FA-SC02U FA-SC01U: 350400 MHz FA-SC02U: 330380 MHz FA-SC61UC FA-SC61UC: 380520 MHz uhf cut antenna belt clip mobile bracket D OTHERS MB-130 Mounts the BC-213 desktop charger on a variety of places in a vehicle. MB-133 HM-158LA/HM-159LA/HM-168LWP/HM-171GPW speaker microphone Combination speaker-microphone that provides convenient operation while the transceiver is hanging on your belt. The HM-171GPW includes high-performance GPS receiver. Adjust the microphone gain before use. HM-153LA/HM-166LA Ideal for hands-free operation. Clip the HM-153LA or HM-166LA (with integrated ptt switch) to your lapel or breast pocket. Adjust the microphone gain before use. HS-94/HS-95/HS-97
+ VS-4LA ptt switch cable
/OPC-2004LA adapter cable HS-94:
HS-95:
HS-97:
VS-4LA:
OPC-2004LA: To connect to headsets for VOX Ear-hook type Neck-arm type Throat microphone To connect to headsets earphone-microphone headset operation Adjust the both microphone and VOX gain before use. HS-94LWP/HS-95LWP HS-94LWP: Ear-hook type HS-95LWP: Neck-arm type Adjust the both microphone and VOX gain before use. headset Some options may not be available in some countries. Ask your dealer for details. Approved Icom optional equipment is designed for optimal performance when used with an Icom transceiver. Icom is not responsible for the destruction or damage to an Icom transceiver in the event the Icom transceiver is used with equipment that is not manufactured or approved by Icom. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia, and/or other countries. All other products or brands are registered trademarks or trademarks of their respective holders.
- 4 -
INSTRUCTIONS VHF DIGITAL TRANSCEIVERS I-F1000D series I-F2000D series UHF DIGITAL TRANSCEIVERS Thank you for purchasing the IC-F1000D series vhf digital transceivers or IC-F2000D series uhf digital transceivers. READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SUPPLIED ACCESSORIES q w e r t q w e r t Battery pack*
Battery charger* (BC-213) Belt clip (MB-133) Power adapter* (for the battery charger) Flexible antenna*
* Not supplied, or the shape is different, depending on the transceiver version. ANTENNA CONNECTOR LED INDICATOR
[PTT]
[Upper]
(Dealer assignable)
[Lower]
(Dealer assignable) PANEL DESCRIPTION
[ROTARY SELECTOR]
[VOL]
[Emer]
Speaker SPEAKER-
MICROPHONE JACK Microphone D About the LED Indicator Lights red while transmitting. Lights green while receiving a signal, or when the squelch is open. Lights or blinks orange when the matched 2-Tone or 5-Tone is received, depending on the presetting. You should charge the battery when the indicator slowly blinks green. You must charge the battery when the indicator blinks green fast. D About the Speaker microphone jack CAUTION: Only when the jack cover or the optional HM-168LWP, HM-171GPW, HS-94LWP, or HS-95LWP is attached, the transceiver meets IP67 requirements for dust-tight and waterproof protection. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-7206H-2EX Printed in Japan 2015 Icom Inc.
- 1 -
BATTERY CHARGING BASIC OPERATION D Receiving and Transmitting CAUTION:
Attach an antenna before transmitting. Transmitting without an antenna may damage the transceiver. Receiving:
Rotate [ROTARY SELECTOR] to select a channel. q Or, push one of [MR-CH 1], [MR-CH 2], [MR-CH 3], or
[MR-CH 4], if assigned to [Upper] or [Lower]. When receiving a call, adjust the audio output level to a comfortable listening level. w Transmitting:
Wait until the channel is clear to avoid interference. q While holding down [PTT], speak at a normal voice level. Release [PTT] to receive. w IMPORTANT:
To maximize the readability of your signal:
1. After pushing [PTT], pause briefly before you start speaking. 2. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak at a normal voice level. Rapid charging the supplied BC-213 D The BC-213 desktop charger rapidly charges the Li-
ion battery pack. The BC-213 is used with a power adapter or the CP-
23L cigarette lighter cable (purchase separately). Charging time of the BP-280 Approximately 3.5 hours CAUTION: STOP charging, if the charge indicator lights orange and green alternately. NOTE: Charge the battery within the specified temperature range of +10C to +40C (+50F to
+104F). Otherwise, the charging time will be longer, but the battery will not reach a full charge. While charging, at a point after the temperature goes out of the specified range, the charging will automatically stop. Rapid charging the BC-214 D The BC-214 multi charger (purchase separately) can simultaneously charge up to 6 Li-ion battery packs. The BC-214 is used with BC-157S ac adapter
(purchase separately) or the OPC-656 dc power cable (purchase separately). For more information about Icom accessories, please read the OPTIONS printed on the reverse side of this instruction sheet. Charging time of the BP-280 Approximately 3.5 hours Turn OFF the Power Power adapter*
Battery pack D Turning power ON Before using the transceiver for the first time, the battery pack must be fully charged for optimum life and operation. See the instructions on page 2. Rotate [VOL] to turn ON the power.
[VOL]
CP-23L
(for 12 V cigarette lighter socket) can be used instead of the power adapter. BC-213*
* Not supplied, or the shape is different, depending on the transceiver version. Transceiver Charge indicator Lights orange while charging. Lights green when charging is completed. Battery pack Transceiver Turn OFF the power BC-157S OPC-656 Connect to a DC power supply:
12 to 16 V, at least 7 A Red line: +
Black line: _ BC-214
- 2 -
- 3 -
1 | User Manual 3 | Users Manual | 169.49 KiB | / January 05 2015 |
FCC INFORMATION VOICE CODING TECHNOLOGY FOR CLASS A UNINTENTIONAL RADIATORS:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-
ence when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communica-
tions. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The AMBE+2 voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed sole-
ly for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassem-
ble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Patent Nos.
#5,870,405, #5,826,222, #5,754,974, #5,701,390,
#5,715,365, #5,649,050, #5,630,011, #5,581,656,
#5,517,511, #5,491,772, #5,247,579, #5,226,084 and
#5,195,166. RECOMMENDATION CAUTION:
Changes or modifications to this transceiver, not ex-
pressly approved by Icom Inc., could void your au-
thority to operate this transceiver under FCC regu-
lations. CLEAN THE TRANSCEIVER THOROUGHLY WITH FRESH WATER after exposure to saltwater, and dry it be-
fore operating. Otherwise, the transceiver's keys, switches and controllers may become unusable due to salt crystalli-
zation. This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. NOTE: DO NOT submerge the transceiver in water if there is any reason (one of the following) to suspect the water-
proof protection may not be effective. When the transceiver has been dropped When the transceivers case or the waterproof seal is cracked or damaged When the jack cover or the optional HM-168LWP, HS-
94LWP, or HS-95LWP is detached from the transceiver COUNTRY CODE LIST ISO 3166-1 Country Codes 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Austria Belgium Bulgaria Croatia Czech Republic Cyprus Denmark Estonia Finland France Germany Greece Hungary Iceland Ireland Italy Latvia AT BE BG HR CZ CY DK EE FI FR DE GR HU IS IE IT LV Country Liechtenstein Lithuania Luxembourg Malta Netherlands Norway Poland Portugal Romania Slovakia Slovenia Spain Sweden Switzerland Turkey United Kingdom 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Codes LI LT LU MT NL NO PL PT RO SK SI ES SE CH TR GB
< Intended Country of Use >
AT FI IT PL GB RO CY DE LT SK LI HR BE FR LV PT IS TR CZ GR LU SI NO DK HU MT ES CH EE IE NL SE BG Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United King-
dom, Germany, France, Spain, Russia, and/or other countries. All other products or brands are registered trademarks or trade-
marks of their respective holders.
- 4 -
PRECAUTIONS VHF DIGITAL TRANSCEIVERS I-F1000D series I-F2000D series UHF DIGITAL TRANSCEIVERS Thank you for choosing the IC-F1000D series vhf digital transceivers or IC-F2000D series uhf digi-
tal transceivers. READ ALL PRECAUTIONS carefully and complete-
ly before using the transceiver. EXPLICIT DEFINITIONS WORD DEFINITION RDANGER!
Personal death, serious injury or an explosion may occur. RWARNING! Personal injury, fire hazard or electric shock may occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No risk of personal injury, fire or electric shock. PRECAUTIONS R DANGER! NEVER short the terminals of the battery pack. R DANGER! Use and charge only specified Icom battery packs with Icom radios or Icom chargers. Only Icom battery packs are tested and approved for use with Icom radios or charged with Icom chargers. Using third-party or counterfeit battery packs or chargers may cause smoke, fire, or cause the battery to burst. R WARNING! NEVER hold the radio that the antenna is very close to, or touching exposed parts of the body, es-
pecially the face or eyes, while transmitting. The radio will perform best if the microphone is 5 to 10 cm (2 to 4 inches) away from the lips and the radio is vertical. R WARNING! NEVER operate the radio with a headset or other audio accessories at high volume levels. Hearing ex-
perts advise against continuous high volume operation. If you experience a ringing in your ears, reduce the volume level or discontinue use. R WARNING! NEVER operate the radio while driving a ve-
hicle. Safe driving requires your full attentionanything less may result in an accident. CAUTION: MAKE SURE the flexible antenna, battery pack and jack cover are securely attached to the radio, and that the antenna and battery pack are dry before attachment. Ex-
posing the inside of the radio to dust or water will result in se-
rious damage to the radio. DO NOT operate the radio near unshielded electrical blast-
ing caps or in an explosive atmosphere. DO NOT push [PTT] when you do not actually intend to transmit. DO NOT use or place the radio in direct sunlight or in ar-
eas with temperatures below 25C (13F) or above +55C
(+131F): ETS version, below 30C (22F) or above
+60C (+140F): TIA version. The basic operations, trans-
mission and reception of the radio are guaranteed within the specified operating temperature range. However, the LCD display may not be operate correctly, or show an indication in the case of long hours of operation, or after being placed in extremely cold areas. DO NOT modify the radio. The specifications may change and then not comply with the requirements of a correspond-
ed regulation. The radio warranty does not cover any prob-
lems caused by unauthorized modification. DO NOT use harsh solvents such as benzine or alcohol when cleaning, as they will damage the radio surfaces. BE CAREFUL! The radio will become hot when operating it continuously for long periods of time. BE CAREFUL! The radio meets IP67* requirements for dust-tight and waterproof protection. However, once the ra-
dio has been dropped, dust-tight and waterproof protection cannot be guaranteed because of possible damage to the radios case or the waterproof seal.
*Only when the jack cover or the optional HM-168LWP is attached. Even when the radio power is OFF, a slight current still flows in the circuits. Remove the battery pack from the radio when not using it for a long time. Otherwise, the installed battery pack will become exhausted, and will need to be recharged or replaced. MAKE SURE to turn the radio power OFF before connecting the supplied or optional equipment. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
- 1 -
A-7xxxX-1EX Printed in Japan 2015 Icom Inc. PRECAUTIONS (Continued) SAFETY TRAINING INFORMATION The information listed above provides the user with the in-
formation needed to make him or her aware of RF exposure, and what to do to assure that this radio operates with the FCC and IC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF ener-
gy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic ra-
diation such as hospitals, aircraft, and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. CAUTION: Always use the battery within the specified temperature range, for the radio 25C to +55C (13F to
+131F): ETS version, 30C to +60C (22F to +140F):
TIA version, and the battery itself 20C to +60C (4F to
+140F). Using the battery out of its specified temperature range will reduce the batterys performance and battery life. Please note that the specified temperature range of the bat-
tery may exceed that of the radio. In such cases, the radio may not work properly because it is out of its operating tem-
perature range. CAUTION: Shorter battery life could occur if the battery is left fully charged, completely discharged, or in an excessive temperature environment (above +50C; +122F) for an ex-
tended period of time. If the battery must be left unused for a long time, it must be detached from the radio after discharg-
ing. You may use the battery until the remaining capacity is about half, then keep it safely in a cool dry place at the fol-
lowing temperature range:
20C (4F) to +50C (+122F) (within a month) 20C (4F) to +40C (+104F) (within three months) 20C (4F) to +20C (+68F) (within a year) BE SURE to replace the battery with a new one after five years, even if still holds a charge. The inside battery material will deteriorate after a period of time, even with little use. Charging caution R DANGER! NEVER charge the battery pack in areas with extremely high temperatures, such as near fires or stoves, inside a sun-heated vehicle, or in direct sunlight. In such en-
vironments, the safety/protection circuit in the battery will activate, causing the battery to stop charging. R WARNING! NEVER charge or leave the battery in the battery charger beyond the specified time for charging. If the battery is not completely charged by the specified time, stop charging and remove the battery from the battery char-
ger. Continuing to charge the battery beyond the specified time limit may cause a fire, overheating, or the battery may rupture. R WARNING! NEVER insert the radio (battery attached to the radio) into the charger if it is wet or soiled. This could cor-
rode the battery charger terminals or damage the charger. The charger is not waterproof. NOTE: Charge the battery within the specified temperature range of +10C to +40C (+50F to +104F). Otherwise, the charging time will be longer, but the battery will not reach a full charge. While charging, at a point after the temperature goes out of the specified range, the charging will automati-
cally stop. Battery caution Misuse of Li-ion batteries may result in the following haz-
ards: smoke, fire, or the battery may rupture. Misuse can also cause damage to the battery or degradation of bat-
tery performance. R DANGER! NEVER short terminals (or charging termi-
nals) of the battery pack. Also, current may flow into nearby metal objects such as a necklace, so be careful when plac-
ing battery packs (or the radio) in handbags, etc. Simply carrying with or placing near metal objects such as a necklace, etc. may cause shorting. This may damage not only the battery pack, but also the radio. R DANGER! DO NOT hammer or otherwise impact the bat-
tery. Do not use the battery if it has been severely impact-
ed or dropped, or if the battery has been subjected to heavy pressure. Battery damage may not be visible on the outside of the case. Even if the surface of the battery does not show cracks or any other damage, the cells inside the battery may rupture or catch fire. R DANGER! NEVER use or leave battery pack in areas with temperatures above +60C (+140F). High tempera-
ture buildup in the battery, such as could occur near fires or stoves, inside a sun heated car, or in direct sunlight may cause the battery to rupture or catch fire. Excessive tem-
peratures may also degrade battery performance or short-
en battery life. R DANGER! DO NOT expose the battery to rain, snow, seawater, or any other liquids. Do not charge or use a wet battery. If the battery gets wet, be sure to wipe it dry before using. R DANGER! KEEP battery packs away from fire. Fire or heat may cause them to rupture or explode. Dispose of used battery packs in accordance with local regulations. R DANGER! NEVER solder the battery terminals, or NEV-
ER modify the battery pack. This may cause heat genera-
tion, and the battery may burst, emit smoke or catch fire. R DANGER! Use the battery only with the radio for which it is specified. Never use a battery with any other equipment, or for any purpose that is not specified in this instruction manual. R DANGER! If fluid from inside the battery gets in your eyes, blindness can result. Rinse your eyes with clean wa-
ter, without rubbing them, and see a doctor immediately. R WARNING! Immediately stop using the battery if it emits an abnormal odor, heats up, or is discolored or deformed. If any of these conditions occur, contact your Icom dealer or distributor. R WARNING! Immediately wash, using clean water, any part of the body that comes into contact with fluid from in-
side the battery. R WARNING! NEVER put the battery in a microwave oven, high-pressure container, or in an induction heating cooker. This could cause a fire, overheating, or cause the battery to rupture. W ARNING Your Icom radio generates RF electromagnet-
ic energy during transmit mode. This radio is designed for and classified as Occupational Use Only, meaning it must be used only dur-
ing the course of employment by individuals aware of the hazards, and the ways to mini-
mize such hazards. This radio is NOT intended for use by the General Population in an uncontrolled environment. This radio has been tested and complies with the FCC and IC RF exposure limits for Occupational Use Only. In addi-
tion, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromag-
netic energy levels and evaluation of such levels for expo-
sure to humans:
FCC OET Bulletin 65 Edition 97-01 Supplement C, Evalu-
ating Compliance with FCC Guidelines for Human Expo-
sure to Radio Frequency Electromagnetic Fields. American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Expo-
sure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potential-
ly Hazardous Electromagnetic Fields RF and Microwave. The antennas, batteries, belt clips, speaker-microphone, and other accessories that are listed in OPTIONS of the INSTRUCTIONS sheet, are authorized for use with this product. Use of accessories other than those specified may result in RF exposure levels exceeding the FCC and IC requirements for wireless RF exposure. To ensure that your expose to RF electro-
magnetic energy is within the FCC and IC allowable limits for occupational use, al-
ways adhere to the following guidelines:
CAU TION DO NOT operate the radio without a proper antenna at-
tached, as this may damaged the radio and may also cause you to exceed FCC and IC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio. DO NOT transmit for more than 50% of total radio use time
(50% duty cycle). Transmitting more than 50% of the time can cause FCC and IC RF exposure compliance require-
ments to be exceeded. The radio is transmitting when the LED indicator lights red. You can cause the radio to trans-
mit by pressing the PTT switch. ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the Icom belt-clips listed in OPTIONS of the INSTRUCTIONS sheet when attaching the radio to your belt, etc., to ensure FCC and IC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound quality, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side.
- 2 -
- 3 -
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2015-02-19 | 136 ~ 174 | TNF - Licensed Non-Broadcast Transmitter Held to Face | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2015-02-19
|
||||
1 | Applicant's complete, legal business name |
ICOM Incorporated
|
||||
1 | FCC Registration Number (FRN) |
0005855366
|
||||
1 | Physical Address |
1-1-32 Kamiminami
|
||||
1 |
Osaka, N/A 547-0003
|
|||||
1 |
Japan
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
v******@ultratech-labs.com
|
||||
1 | TCB Scope |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
AFJ
|
||||
1 | Equipment Product Code |
369600
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
A****** T********
|
||||
1 | Title |
General Manager
|
||||
1 | Telephone Number |
+8166********
|
||||
1 | Fax Number |
+8166********
|
||||
1 |
w******@icom.co.jp
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 05/01/2015 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | TNF - Licensed Non-Broadcast Transmitter Held to Face | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | VHF Transceiver | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | Yes | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output is at the antenna terminal of the device. SAR for body worn operation has been tested and meets the FCC RF exposure guidelines when used with the ICOM listed accessories designated for this product as shown in the filing. End users must be informed of the body worn requirements for satisfying RF exposure compliance. This transmitter may operate only with antennas as described in this filing. This device must transmit with a source-based time-averaging duty factor not exceeding 50%. This device must be restricted to work related operations in an occupational/controlled RF exposure environment. SAR was evaluated for body worn and held-to-face operating modes. Maximum SAR values reported are: Body 0.70 W/Kg and Head 0.29 W/Kg. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
UltraTech Engineering Labs Inc.
|
||||
1 | Name |
T******** L******
|
||||
1 | Telephone Number |
905-8********
|
||||
1 | Fax Number |
905-8********
|
||||
1 |
t******@ultratech-labs.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 22,74,80,9 | EF | 136 | 174 | 5 | 2 ppm | 11K0F3E | |||||||||||||||||||||||||||||||||
1 | 2 | 22,74,80,9 | EF | 136 | 174 | 1 | 2 ppm | 11K0F3E | |||||||||||||||||||||||||||||||||
1 | 3 | 22,74,8 | EF | 136 | 174 | 5 | 2 ppm | 16K0F3E | |||||||||||||||||||||||||||||||||
1 | 4 | 22,74,8 | EF | 136 | 174 | 1 | 2 ppm | 16K0F3E | |||||||||||||||||||||||||||||||||
1 | 5 | 22,74,80,9 | EF ES | 136 | 174 | 5 | 2 ppm | 4K00F1E | |||||||||||||||||||||||||||||||||
1 | 6 | 22,74,80,9 | EF ES | 136 | 174 | 1 | 2 ppm | 4K00F1E | |||||||||||||||||||||||||||||||||
1 | 7 | 22,74,80,9 | EF ES | 136 | 174 | 5 | 2 ppm | 4K00F1D | |||||||||||||||||||||||||||||||||
1 | 8 | 22,74,80,9 | EF ES | 136 | 174 | 1 | 2 ppm | 4K00F1D |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC