PRECAUTIONS D Battery caution Thank you for choosing this Icom product. READ ALL INSTRUCTIONS carefully and completely before using this product. IMPORTANT SAVE THESE INSTRUCTIONS These instructions contain basic operating instructions for the IP110H. This instruction sheet includes some functions that are usable only when they are set in the Controller. The transceiver may have other functions and operations that are not described in this instruction sheet. Ask your dealer for details. DO NOT OPEN, JOLT, SHORT, OR INCINERATE, AS THE BATTERY MAY IGNITE OR BURST. EXPLICIT DEFINITIONS WORD R DANGER!
R WARNING!
CAUTION NOTE DEFINITION Personal death, serious injury or an explosion may occur. Personal injury, fire hazard or electric shock may occur. Equipment damage may occur. If disregarded, inconvenience only. No risk of personal injury, fire or electric shock. Icom is not responsible for the destruction, damage to, or performance of any Icom or non-Icom equipment, if the malfunction is because of:
Force majeure, including, but not limited to, fires, earthquakes, storms, floods, lightning, other natural disasters, disturbances, riots, war, or radioactive contamination. The use of Icom transceivers with any equipment that is not manufactured or approved by Icom. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand, and/or other countries. The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Icom Inc. is under license. Other trademarks and trade names are those of their respective owners. R DANGER! NEVER operate the transceiver near unshielded electrical blasting caps or in an explosive atmosphere. This could cause an explosion and death. R DANGER! NEVER charge Icom transceivers with non-Icom chargers. Only Icom transceivers are tested and approved for charged with Icom chargers. Using third-
party or counterfeit chargers may cause smoke, fire, or cause the battery to burst. R WARNING RF EXPOSURE! This device emits Radio Frequency (RF) energy. Caution should be observed when operating this device. If you have any questions regarding RF exposure and safety standards, please refer to the Federal Communications Commission Office of Engineering and Technologys report on Evaluating Compliance with FCC Guidelines for Human Radio Frequency Electromagnetic Fields (OET Bulletin 65). R WARNING! NEVER hold the transceiver so that it is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. R WARNING! NEVER operate or touch the transceiver with wet hands. This could cause an electric shock or damage the transceiver. R WARNING! NEVER operate the transceiver with earphones, a headset, or other audio accessories at high volume levels. The continuous high volume operation may cause a ringing in your ears. If you experience the ringing in your ears, reduce a volume level or discontinue use. CAUTION: DO NOT operate the transceiver while driving a vehicle. Safe driving requires your full attention anything less may result in an accident. CAUTION: DO NOT use harsh solvents such as Benzine or alcohol when cleaning. This could damage the equipment surfaces. If the surface becomes dusty or dirty, wipe it clean with a soft, dry cloth. CAUTION: DO NOT operate the transceiver unless the jack cap and connector cover are securely attached to the transceiver. Exposing the inside of the transceiver to dust or water will result in serious damage to the transceiver. After exposure to water, clean the transceiver thoroughly with fresh water and dry it completely to remove any water or salt residue. CAUTION: DO NOT use or leave the transceiver in areas with temperatures below 10C (14F) or above +60C
(140F), or in areas subject to direct sunlight, such as the dashboard. NEVER leave the transceiver in an insecure place to avoid use by unauthorized persons. DO NOT push [PTT] unless you actually intend to transmit. DO NOT modify the transceiver. The specifications may change and then the transceiver may not comply with the requirements of required regulations. The transceiver warranty does not cover any problems caused by unauthorized modification. BE CAREFUL! The transceiver may become hot after continuously transmitting for long periods of time. BE CAREFUL! The transceiver meets IP67/IP54*
requirements for dust-tight and waterproof protection. However, once the transceiver has been dropped, or the waterproof seal is cracked or damaged, dust-tight and waterproof protection cannot be guaranteed due to the fact that the transceiver may be cracked or the waterproof seal damaged, and so on.
* Only when the jack cap and connector cover are attached. FCC INFORMATION SAFETY TRAINING INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CAUTION: Changes or modifications to this device, not expressly approved by Icom Inc., could void your authority to operate this device under FCC regulations. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. FOR CANADA This device contains licence-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. The device for operation in the band 51505350 MHz is only for indoor use to reduce the potential for harmful interference to cochannel mobile satellite systems. The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-
level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. This device has been tested and found to comply with FCC/ISED radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio frequency (RF) Exposure rules. ABOUT CE AND DOC Hereby, Icom Inc. declares that the versions of IP110H which have the CE symbol on the product, comply with the essential requirements of the Radio Equipment Directive, 2014/53/EU, and the restriction of the use of certain hazardous substances in electrical and electronic equipment Directive, 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address:
https://www.icomjapan.com/support/
DISPOSAL The crossed-out wheeled-bin symbol on your product, literature, or packaging reminds you that in the European Union, all electrical and electronic products, batteries, and accumulators (rechargeable batteries) must be taken to designated collection locations at the end of their working life. Do not dispose of these products as unsorted municipal waste. Dispose of them according to the laws in your area. RECOMMENDATION CLEAN THE TRANSCEIVER THOROUGHLY IN A BOWL OF FRESH WATER after exposure to saltwater, and dry it before operating. Otherwise, the transceivers keys, switches, and controllers may become unusable, due to salt crystallization, and/or the charging terminals of the battery pack may corrode. NOTE: If the transceivers waterproof protection appears defective, carefully clean it with a soft, damp (fresh water) cloth, then dry it before operating. The transceiver may lose its waterproof protection if the case, jack cap, or connector cover is cracked or broken, or the transceiver has been dropped. Contact your Icom distributor or your dealer for advice. Misuse of Li-ion batteries may result in the following hazards: smoke, fire, or the battery may rupture. Misuse can also cause damage to the battery or degradation of battery performance. R DANGER! NEVER incinerate a used transceiver. Internal battery gas may cause an explosion. R DANGER! NEVER strike or otherwise impact the transceiver. Do not use the transceiver if it has been severely impacted or dropped, or if the transceiver has been subjected to heavy pressure. Battery damage may not be visible on the outside of the case. Even if the surface of the transceiver does not show cracks or any other damage, the cells inside the battery may rupture or catch fire. R DANGER! NEVER leave the transceiver in places with temperatures above 60C (140F). High temperature buildup in the battery cells, such as could occur near fires or stoves, inside a sun-heated vehicle, or in direct sunlight for long periods of time may cause the battery cells to rupture or catch fire. Excessive temperatures may also degrade the transceivers performance or shorten the battery cells life. R DANGER! NEVER place the transceiver near a fire. Fire or heat may cause them to rupture or explode. Dispose of used battery pack in accordance with local regulations. R DANGER! NEVER solder the charging terminals, or NEVER modify the transceiver. This may cause heat generation, and the battery may burst, emit smoke or catch fire. R DANGER! NEVER let fluid from inside the battery get in your eyes. This can cause blindness. Rinse your eyes with clean water, without rubbing them, and immediately go to a doctor. R WARNING! NEVER let fluid from inside the battery cells come in contact with your body. If it does, immediately wash with clean water. R WARNING! NEVER put the transceiver in a microwave oven, high-pressure container, or in an induction heating cooker. This could cause a fire, overheating, or cause the battery cells to rupture. R WARNING! NEVER use a deteriorated transceiver. It could cause a fire. CAUTION: DO NOT use the transceiver out of the specified temperature range, 10C ~ +60C (14F
~ 140F). Using the transceiver out of its specified temperature range will reduce its performance and battery cells life. CAUTION: DO NOT leave the transceiver fully charged, completely discharged, or in an excessive temperature environment for an extended period of time. You may use the transceiver until the remaining battery capacity is about half, then keep it safely in a cool and dry place. CAUTION: DO NOT continue to use the transceiver if it emits an abnormal odor, heats up, or is discolored or deformed. If any of these conditions occur, contact your Icom dealer or distributor. PRCAUTIONS R DANGER ! NE JAMAIS utiliser lmetteur-rcepteur proximit de dtonateurs lectriques non blinds ou dans une atmosphre explosive. Cela pourrait causer une explosion mortelle. R DANGER ! NE JAMAIS recharger des metteurs-
rcepteurs Icom avec des chargeurs non-Icom. Seuls les metteurs-rcepteurs Icom sont tests et homologus pour tre chargs avec des chargeurs Icom. Lutilisation de chargeurs tiers ou de contrefaon peut tre lorigine de fumes, dincendie ou peut faire clater la batterie. R AVERTISSEMENT RELATIF LEXPOSITION AUX RADIO-FRQUENCES ! Cet metteur-rcepteur met des ondes de radio-frquences (RF). Lmetteur-rcepteur doit tre utilis avec la plus grande prudence. Pour toute question concernant lexposition aux radiofrquences et les rgles de scurit, veuillez consulter le rapport Engineering and Technology du Bureau fdral de commission des communications (FCC) sur lvaluation de la conformit la rglementation FCC sur Iexposition de lhomme aux champs lectromagntiques de radiofrquences (Bulletin OET 65). R AVERTISSEMENT ! NE JAMAIS tenir lmetteur-
rcepteur place proximit immdiate ou en contact avec des parties du corps exposes, en particulier le visage ou les yeux, lors des transmissions. R AVERTISSEMENT ! NE JAMAIS utiliser ou toucher lmetteur-rcepteur avec des mains mouilles. Cela pourrait causer un choc lectrique ou endommager lmetteur-rcepteur. R AVERTISSEMENT ! NE JAMAIS utiliser lmetteur-
rcepteur avec des couteurs, un casque ou tout autre accessoire audio un niveau sonore lev. Lutilisation continue un niveau sonore lev peut provoquer un bourdonnement dans vos oreilles. Si vous entendez une sonnerie, baissez le niveau sonore ou interrompez lutilisation. MISE EN GARDE : NE PAS utiliser lmetteur-rcepteur en conduisant un vhicule. La scurit de la conduite requiert toute lattention du conducteur toute dfaillance peut tre lorigine dun accident. MISE EN GARDE : NE PAS utiliser de solvants agressifs tels que du Benzine ou de lalcool lors du nettoyage. Cela risque dendommager les surfaces de lquipement. Si la surface est poussireuse ou sale, nettoyez-la avec un tissu doux et sec. MISE EN GARDE : NE PAS utiliser lmetteur-rcepteur moins que le capuchon de jack et le couvercle du connecteur soient bien fixs lmetteur-rcepteur. Exposer lintrieur de lmetteur-rcepteur leau ou la poussire endommagera srieusement lmetteur-rcepteur. Aprs tout contact avec de leau, nettoyer soigneusement lmetteur-rcepteur leau courante et schez-le compltement afin dliminer leau ou les dpts de sel. MISE EN GARDE : NE PAS utiliser ou laisser lmetteur-
rcepteur dans des zones o la temprature est infrieure 10C (14F) ou suprieure +60C (140F) dans des zones directement exposes aux rayons du soleil, comme le tableau de bord. NE JAMAIS laisser lmetteur-rcepteur dans un endroit peu sr pour viter que des personnes non autorises ne lutilisent. NE PAS appuyer sur [PTT] sans intention relle dmettre. NE PAS modifier lmetteur-rcepteur. Les spcifications peuvent changer et lmetteur-rcepteur peut ainsi ne plus tre conforme aux exigences imposes par la rglementation. La garantie de lmetteur-rcepteur ne couvre pas les problmes rsultant dune modification non autorise. BE SURE to have the battery replaced with a new one approximately five years after manufacturing, even if it still holds a charge. The material inside the battery cells will become weak after a period of time, even with little use. The estimated number of times you can charge the transceiver is between 300 and 500. Even when the transceiver appears to be fully charged, the operating time of the transceiver may become short when:
Approximately 5 years have passed since the battery was manufactured. The battery has been repeatedly charged. Contact your Icoms local service shop or authorized Icom dealer about the battery replacement.
(Icom global site: https://www.icomjapan.com/) D Charging caution R DANGER! NEVER charge the transceiver in areas with extremely high temperatures, such as near fires or stoves, inside a sun-heated vehicle, or in direct sunlight. R WARNING! NEVER charge the transceiver during a lightning storm. It may result in an electric shock, cause a fire or damage the transceiver. Always disconnect the power adapter before a storm. R WARNING! NEVER charge or leave the transceiver in the battery charger beyond the specified time for charging. If the transceiver is not completely charged by the specified time, stop charging and remove the transceiver from the battery charger. Continuing to charge the transceiver beyond the specified time limit may cause a fire, overheating, or the battery may rupture. R WARNING! Occasionally observe the transceiver condition while charging. If any abnormal condition occurs, discontinue using the transceiver. CAUTION: DO NOT insert the transceiver into the charger if it is wet or soiled. This could corrode the battery charger terminals or damage the charger. The charger is not waterproof. NOTE: DO NOT charge the transceiver outside of the specified temperature range: 0C ~ 40C (32F ~ 104F). Otherwise, the charging time will be longer, but the battery will not reach a full charge. While charging, at a point after the temperature goes out of the specified range, the charging will automatically stop. Bluetooth INTERFERENCE Bluetooth uses the 2.4 GHz band. When using the transceiver in the 2.4 GHz band near a Bluetooth device, interference may occur. This may cause a decrease in communication speed, and an unstable connection. In such case, use the transceiver away from the Bluetooth device communication area, or stop using the Bluetooth device. PRECAUTIONS ON USING THE WIRELESS LAN We recommend that users with pacemakers take precautions to be sure that this device does not cause them a problem because of electromagnetic interferences. DO NOT use this device near microwave ovens. A microwave oven may cause electromagnetic interference to the communications through this device. DO NOT modify the device. The device warranty does not cover any problems caused by unauthorized modification. For Canada Operation of this device in the 51505350 MHz frequency range is restricted to indoor operation only. Outdoor operation in the 51505350 MHz frequency range is prohibited. ATTENTION ! Lmetteur-rcepteur chauffe en cas dutilisation continue sur une longue dure. ATTENTION ! Lmetteur-rcepteur rpond aux exigences de la norme IP67/IP54* en matire de protection tanche la poussire et de rsistance leau. Cependant, en cas de chute de lmetteur-rcepteur, la protection contre la poussire et la rsistance aux claboussures ne peuvent plus tre garanties, car lmetteur-rcepteur risque dtre fissur ou le joint dtanchit endommag, etc.
* Uniquement lorsque le capuchon de jack et le couvercle du connecteur sont fournis. D Mise en garde concernant la batterie Une mauvaise utilisation des batteries au Li-ion prsente les risques suivants : dgagement de fume, incendie ou clatement de la batterie. Une mauvaise utilisation peut galement endommager la batterie ou en dgrader ses performances. R DANGER ! NE JAMAIS incinrer de lmetteur-
rcepteur usags. Le gaz interne de la batterie peut provoquer une explosion. R DANGER ! NE JAMAIS cogner ou provoquer dautres chocs sur lmetteur-rcepteur. Nutilisez pas lmetteur-
rcepteur si elle a reu des impacts ou a t jete ou si elle a subi une forte pression. Les dommages subis par une batterie peuvent ne pas tre visibles de lextrieur du botier. Mme si la surface de lmetteur-rcepteur ne semble pas fissure ou endommage, les cellules lintrieur de la batterie peuvent se rompre ou prendre feu. R DANGER ! NE JAMAIS laisser lmetteur-rcepteur dans des lieux dans lesquels les tempratures sont suprieures 60C (140F). La monte en temprature des cellules de la batterie, comme cela peut survenir proximit de flammes ou de poles, lintrieur dun vhicule expos au soleil, ou en plein soleil pendant une longue priode de temps, peut dtruire ou enflammer les cellules de la batterie. Les tempratures excessives peuvent galement dgrader les performances de lmetteur-rcepteur ou rduire la dure de vie des cellules de la batterie. R DANGER ! NE JAMAIS placer de lmetteur-rcepteur prs dun feu. La chaleur ou des flammes peuvent provoquer un clatement ou une explosion. Mettre au rebut les blocs-batteries usags conformment la rglementation locale. R DANGER ! NE JAMAIS souder les bornes de charge et NE JAMAIS modifier lmetteur-rcepteur. Ceci peut provoquer une surchauffe de la batterie, qui risque alors dclater, de fumer ou de prendre feu. R DANGER ! NE JAMAIS laisser du liquide provenant de lintrieur de la batterie entrer en contact avec vos yeux. Cela peut provoquer une ccit. Rincez abondamment vos yeux leau courante, sans les frotter et consultez immdiatement un mdecin. R AVERTISSEMENT ! NE JAMAIS laisser du liquide provenant de lintrieur des cellules de la batterie entrer en contact avec votre corps. Si cela se produit, rincez immdiatement avec de leau propre. R AVERTISSEMENT ! NE JAMAIS mettre lmetteur-
rcepteur dans un four micro-ondes, un rcipient haute-
pression ou dans un appareil de cuisson par induction. Ceci peut provoquer un incendie, une surchauffe ou conduire la rupture des cellules de la batterie. R AVERTISSEMENT ! NE JAMAIS utiliser de lmetteur-
rcepteur endommages. Cela pourrait provoquer un incendie. INSTRUCTIONSWLAN TRANSCEIVERIP110H1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, JapanA7654D-1EX-1aPrinted in Japan 20212022 Icom Inc.Mar. 2022 PRCAUTIONS (suite) INTERFRENCES Bluetooth POUR LE CANADA Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. Lappareil ne doit pas produire de brouillage;
2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Lappareil destin fonctionner dans la bande de 5150 5350 MHz est rserv une utilisation en intrieur afin de limiter le risque dinterfrence perturbatrice des systmes satellites mobiles utilisant le mme canal. INFORMATION SUR LA FORMATION LA SCURIT Les connaissances scientifiques dont nous disposons nont mis en vidence aucun problme de sant associ lusage des appareils sans fil faible puissance. Nous ne sommes cependant pas en mesure de prouver que ces appareils sans fil faible puissance sont entirement sans danger. Les appareils sans fil faible puissance mettent une nergie frquence radiolectrique (RF) trs faible dans le spectre des micro-ondes lorsquils sont utiliss. Alors quune dose leve de RF peut avoir des effets sur la sant (en chauffant les tissus), lexposition de faibles RF qui ne produisent pas de chaleur na pas de mauvais effets connus sur la sant. De nombreuses tudes ont t menes sur les expositions aux RF faibles et nont dcouvert aucun effet biologique. Certaines tudes ont suggr quil pouvait y avoir certains effets biologiques, mais ces rsultats nont pas t confirms par des recherches supplmentaires. Cet appareil a t test et jug conforme aux limites dexposition aux rayonnements nonces pour un environnement non contrl et respecte les rgles les radiolectriques (RF) de la FCC lignes directrices dexposition et dexposition aux frquences radiolectriques (RF) CNR-102 de l ISDE. SUPPLIED ACCESSORIES Belt clip USB cable (USB Type-A/USB Type-C) NOTE: Some accessories are not supplied, or the shape is different, depending on the transceiver version. D Mise en garde concernant la batterie MISE EN GARDE : NE PAS utiliser lmetteur-rcepteur en dehors de la plage de temprature indique, 10C
+60C (14F 140F). Lutilisation de lmetteur-rcepteur hors de la plage de temprature spcifie rduit les performances et la longvit des cellules de la batterie. MISE EN GARDE : NE PAS laisser lmetteur-rcepteur pleine charge, entirement dcharg, ou dans un environnement temprature excessive pendant une priode prolonge. Vous pouvez utiliser lmetteur-rcepteur jusqu ce que la capacit restante de la batterie soit rduite de moiti, puis gardez-le en scurit dans un endroit frais et sec. MISE EN GARDE : NE PAS utiliser lmetteur-rcepteur si elle dgage une odeur anormale, si elle surchauffe, est dcolore ou dforme. Si lune de ces situations se produit, contacter votre revendeur ou distributeur Icom. VEILLER remplacer le batterie par un neuf environ cinq ans aprs sa fabrication, mme sil tient la charge. Les matriaux prsents lintrieur des cellules de la batterie se dtriorent aprs un certain temps, mme en cas dutilisation rduite. Lestimation du nombre de fois que vous pouvez recharger lmetteur-rcepteur est comprise entre 300 et 500. Mme lorsque lmetteur-rcepteur semble compltement charg, le temps de fonctionnement de lmetteur-rcepteur peut tre rduit si :
La batterie a t fabrique il y a environ 5 ans. La batterie a t charge de nombreuses fois. Adressez-vous votre fournisseur local Icom ou votre revendeur Icom certifi pour des informations sur le remplacement de la batterie.
(Site Icom global : https://www.icomjapan.com/) D Mise en garde concernant la recharge R DANGER ! NE JAMAIS charger lmetteur-rcepteur des endroits exposs des tempratures extrmement leves, comme proximit de flammes ou de poles, lintrieur dun vhicule expos au soleil, ou en plein soleil. R AVERTISSEMENT ! NE JAMAIS charger lmetteur-
rcepteur durant un orage. Cela risquerait de provoquer un choc lectrique, un incendie ou dendommager lmetteur-rcepteur. Toujours dbrancher ladaptateur de courant avant une tempte. R AVERTISSEMENT ! NE JAMAIS charger ou laisser lmetteur-rcepteur dans le chargeur de batterie au-del du temps spcifi pour la charge. Si lmetteur-rcepteur nest pas compltement charge pendant le temps spcifi, interrompez la charge et retirez lmetteur-rcepteur du chargeur de batterie. En continuant charger lmetteur-
rcepteur au-del du temps spcifi, vous pouvez provoquer un incendie, une surchauffe ou dtriorer la batterie. R AVERTISSEMENT ! Vrifiez rgulirement ltat de lmetteur-rcepteur pendant le chargement. Si vous constatez une anomalie, nutilisez plus lmetteur-rcepteur. MISE EN GARDE : NE PAS insrer lmetteur-rcepteur dans le chargeur sil est mouill ou sale. Ceci peut corroder les bornes du chargeur de la batterie ou endommager le chargeur. Le chargeur nest pas tanche. REMARQUE : NE PAS charger lmetteur-rcepteur en dehors de la plage de temprature indique : 0C ~
40C (32F ~ 104F). Dans le cas contraire, le temps de charge sera plus long, mais la batterie natteindra pas une charge complte. Pendant la charge, une fois que la temprature est hors de la plage spcifie, la charge sarrte automatiquement. Bluetooth utilise la bande de 2,4 GHz. Si vous utilisez lmetteurs-rcepteurs dans la bande de 2,4 GHz proximit dun appareil Bluetooth, ceci peut provoquer des interfrences. Ceci peut rduire le dbit de communication et rendre la connexion instable. Dans ce cas, utilisez lmetteurs-rcepteurs distance suffi sante de la zone de communication de lappareil Bluetooth ou cessez dutiliser lappareil Bluetooth. PRCAUTIONS POUR LUTILISATION DU RSEAU LOCAL SANS FIL Nous recommandons aux utilisateurs portant un stimulateur cardiaque de sassurer que cet appareil ne cause pas de problme dinterfrences lectromagntiques. NE PAS utiliser cet appareil proximit dun four micro-ondes. Un four micro-ondes peut provoquer des interfrences lectromagntiques pendant les communications laide de cet appareil. NE PAS modifier lappareil. Lappareil ne couvre pas les problmes rsultant dune modification non autorise. Pour le Canada Cet appareil est restreint une utilisation lintrieur, dans la bande de frquences 51505350 MHz. Lutilisation lextrieur nest pas autorise, dans la bande de frquences 51505350 MHz. INFORMATION FCC Cet appareil est conforme la partie 15 de la rglementation FCC. Son fonctionnement est soumis la condition que cet appareil ne provoque pas dinterfrences nocives. Cet quipement a t test et reconnu conforme aux limites fixes pour un appareil numrique de classe B, conformment la partie 15 de la rglementation FCC. Ces limites ont t fixes afin dassurer une protection raisonnable contre les interfrences nocives dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre un rayonnement de frquence radio. Sil na pas t install conformment aux instructions, il peut par ailleurs crer des interfrences perturbant les communications radio. Toutefois, il ny a aucune garantie que les interfrences ne se produiront pas dans une installation particulire. Si cet quipement cre des interfrences perturbant la rception de la radio ou de la tlvision, comme cela peut tre dtermin en teignant et en allumant lquipement, lutilisateur est invit essayer de corriger linterfrence en prenant une ou plusieurs des mesures ci-aprs :
Rorienter ou changer de place lantenne de rception. loigner lquipement et le rcepteur. Connecter lquipement sur une prise sur un autre circuit que celui sur lequel le rcepteur est connect. Faire appel au revendeur ou un technicien radio/TV expriment. MISE EN GARDE : Tout changement ou modification, non expressment approuv par Icom Inc., peut annuler lautorisation de lutilisateur utiliser cet appareil conformment la rglementation FCC. Cet appareil est conforme la partie 15 de la rglementation FCC. Son utilisation est soumise au respect de deux conditions : (1) Cet appareil ne doit pas causer dinterfrences nuisibles et (2) cet appareil doit accepter toute interfrence reue, y compris les interfrence pouvant entraner un fonctionnement non dsir. Cet metteur ne doit pas tre situ ou utilis en conjonction avec une autre antenne ou un autre metteur. OPTIONS D Chargers BC-257:
BC-228:
D Belt clip MBB-1:
D Cables OPC-2132:
OPC-2133:
OPC-2480:
BATTERY CHARGER AC ADAPTER
( When using multiple BC-257s connected together.) BELT CLIP OPC-1655:
OPC-478UC*1:
D Speaker-Microphones HM-186PI:
HM-228:
PLUG ADAPTER CABLE PLUG ADAPTER CABLE USB CABLE
(USB Type-A/USB Type-C) PROGRAMMING ADAPTER CABLE PROGRAMMING CABLE COMPACT SPEAKER MICROPHONE SPEAKER MICROPHONE Full sized waterproof speaker microphone including alligator type clip to attach to your shirt or collar, and so on. HEADSET (Ear hook type) HEADSET (Neck and arm type) HEADSET (Throat Microphone) Bluetooth HEADSET DURABLE EARPHONE MICROPHONE D Headsets and Earphone microphone HS-94*2:
HS-95*2:
HS-97*2:
VS-3:
HM-179PI:
D Earphone SP-16PIBW:
*1 The OPC-1655 (Programming adapter cable) is required.
*2 The OPC-2133 (Plug adapter cable) is required. EARPHONE (Ear hook type) 11 ATTACHING THE BELT CLIP Clip cover 11 11 11 22 22 Supplied belt clip When removing the belt clip, lift the tab up 1, and slide the belt clip in the direction of the arrow 2. 22 22 Slide the belt clip in the direction of the arrow until the belt clip locks in place, and makes a click sound. TIP: When attaching a hand strap (User supplied) Clip cover Hand strap (User supplied) 11 11 22 22 BATTERY CHARGING PANEL DESCRIPTION FUNCTION DISPLAY BASIC OPERATION Fully charge the transceiver before using for the first time, or if it has not been used for more than 2 months. The charger automatically restarts charging when the battery voltage drops. Disconnect the AC adapter from the outlet when the charger is not in use. NOTE: Instructions and screens on this guide may differ, depending on the Controller settings. Clip cover Jack cap Status indicator USB connector
(Type-C)
[MENU]
[ENT
Status indicator Lights blue: Charging Charged Not lit:
Supplied USB cable Connector cover Turn OFF AC adapter
(User supplied)
[PTT]
Speaker Function display Microphone
CLR]
NOTE:
Use a 5 V/2 A output AC adapter. The charging time may differ, depending on the AC adapter. When you use a low output AC adapter, it may take longer to charge, or the transceiver may not be charged. Before using the AC adapter, thoroughly read its instructions. CONNECTING OPTIONAL EQUIPMENT When connecting optional equipment:
Be sure to turn OFF the transceiver before connecting or disconnecting optional equipment to or from the jack. Remove the cable by holding the plug, not the cable. Insert the plug securely when connecting the cable. CAUTION: Attach the jack cap when no optional equipment is connected. 22 33 Jack cap 11 L Use a coin or standard screwdriver to protect your fingers. L The USB connector does not support USB Power Delivery (USB PD). D Operating keys
[PTT] switch Hold down to transmit, release to receive.
] key
Hold down for 2 seconds to turn the transceiver ON or OFF. CLR] key*
In the Standby screen, push to display the ID List screen. In the MENU screen, push to return to the previous screen.
[]/[] key In the Standby screen, push to adjust the audio level. In the MENU screen, push to select a setting item or value.
[ENT In the Standby screen, hold down for 1 second to turn
] key the Lock function ON or OFF. In the MENU screen, push to set the selected item or option. 44
[MENU] key*
In the Standby screen, push to display the MENU screen. In the MENU screen, push to go back to the Standby screen.
* Ask your dealer about the function when holding down the key for 1 second. D Turning the transceiver ON or OFF Turning ON:
z Hold down [
] for 2 seconds. A beep sounds. Turning OFF:
z Hold down [
] for 2 seconds. Adjusting the audio output level:
z Push []/[] to adjust the audio output level. L The volume can be adjusted between 0 and 32. NOTE: If the output level is set to the minimum, the beep does not sound. D Receiving and transmitting Receiving:
z When a call is received, the status indicator lights green. Push []/[] to adjust the audio output level to a comfortable listening level. Transmitting:
z While holding down [PTT], speak at your normal voice level. Represents the signal strength in 3 levels. blinks when your transceiver is not connected to any Access Points. is displayed if your transceiver is not registered, or not connected to the Controller. Displayed when the Area Call function is ON. blinks when there is new recorded data. is displayed when the Recording function is ON. blinks while recording audio. Displayed when the Key Lock function is ON. The status indicator lights red while [PTT] is pushed. Displayed when the Pocket Beep function is ON. Blinks when a call is received. This icon blinks until the transceiver returns to the Standby mode after a received signal disappears. Displayed when the P-Bell function is used. is displayed when the Bluetooth function is ON. is displayed when the transceiver is connected to a Bluetooth device. Displayed when the VOX function is ON. Displayed when transmission is inhibited. Displayed when the Vibration function is ON. Displayed when the received audio is muted. Displayed when a USB device is connected through a USB cable. Represents the remaining capacity in 4 steps. is displayed while charging. Talk while receiving a call:
z While receiving a call, push [PTT] to talk in the Full Duplex mode* like a telephone call. In the Full Duplex mode, the status indicator lights yellow.
* Depending on the Controller setting. Ask your dealer for details. L If howling occurs, turn down the audio level. IMPORTANT:
To maximize the readability of your signal:
1. After pushing [PTT], pause briefly before you start speaking. 2. Hold the microphone 5 ~ 10 cm (2 ~ 4 inches) from your mouth, then speak at your normal voice level.
[PTT]
Status indicator Microphone
DISPLAYING THE AUTHENTICATION SCREEN Refer to the Authentication screen for authentication acquired with the transceiver. 1. Hold down [
] for 2 seconds to turn ON the transceiver. 2. After the standby screen is displayed, push [MENU] to display the MENU screen. 3. Push []/[] to select Authentication, and then push
[ENT The authentication is displayed. L Push []/[] to scroll the authentication. Suppliers Declaration of Conformity Suppliers Declaration of Conformity FCC Compliance Statement The product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. FCC Compliance Statement The product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party Company Name: Icom America Inc. Address:
12421 Willows Road NE Kirkland, WA 98034 Responsible Party Company Name: Icom America Inc. Address:
12421 Willows Road NE Kirkland, WA 98034 U.S. Contact Information 800-USA-ICOM (800-872-4266) Monday Friday 7 AM to 5 PM PST U.S. Contact Information 800-USA-ICOM (800-872-4266) Monday Friday 7 AM to 5 PM PST Mar. 2022 A7686W-1US Mar. 2022 A7686W-1US Suppliers Declaration of Conformity Suppliers Declaration of Conformity FCC Compliance Statement The product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. FCC Compliance Statement The product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party Company Name: Icom America Inc. Address:
12421 Willows Road NE Kirkland, WA 98034 Responsible Party Company Name: Icom America Inc. Address:
12421 Willows Road NE Kirkland, WA 98034 U.S. Contact Information 800-USA-ICOM (800-872-4266) Monday Friday 7 AM to 5 PM PST U.S. Contact Information 800-USA-ICOM (800-872-4266) Monday Friday 7 AM to 5 PM PST Mar. 2022 A7686W-1US Mar. 2022 A7686W-1US