ESC SOUNDS SERIES 2 User Manual READ THIS MANUAL BEFORE USING THIS PRODUCT. FAILURE TO FOLLOW THE INSTRUCTIONS AND SAFETY PRECAUTIONS IN THIS MANUAL CAN RESULT IN SERIOUS INJURY OR DEATH. INTRODUCTION Thank you for choosing the Series 2, we really appreciate all your support. This manual should provide you all the information that you need to operate your Series 2, but if you experience any issues at all then please dont hesitate to contact us through our website or social media platforms. PRODUCT DESCRIPTION PRODUCT FUNCTION PARAMETERS HOW TO USE 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Right and left earbuds can be used individually
(mono) or simultaneously (stereo) Diameter: 17mm Bluetooth Chip: Realtek Bluetooth Version: V5 Bluetooth Frequency: 20HZ-20KHZ Sensitivity: -38db MIC Earbud Battery: 40 mah with rechargeable customised Li-ion single cell Distance: At least 10 meters (without obstacles) Playing Time: Up to 4.5 hours Standby Time: 100 hours (mono), 45 hours(binaural) Built-in CVC 6.0 noise cancellation technology 6mm high fidelity speakers Charging Case: 500 MAH Support: Android and IOS system Bilateral calling SWITCHING ON AND PAIRING THE SERIES 2
(STEREO USE) 1. Remove both Series 2 from the charging case 2. Both Series 2 will now switch on and connect automatically with each other 3. After a short beep the Series 2 will now search for a Bluetooth device 4. Turn on the Bluetooth on your device CONNECTING THE SERIES 2 TO YOUR DEVICE 1. Once the Series 2 are paired this will be indicated by flashing red and blue lights in the left (master) Series 2 and a flashing blue light in the right
(secondary) Series 2 2. Open the Bluetooth option on your mobile device 3. Select the option S.2 4. Once the connection has been achieved your Bluetooth status will display as Connected and an audio message of Connected will be transmitted by the Series 2 1. Charging Case 2. Charging Indicator 3. Charge Contact Point 4. Ear Tip 5. Ear Brace 6. Microphone 7. Multi-Function Key (Pair, Pause/Play, Answer Call/
Dial, Play Next Song/Previous Song) SWITCHING ON AND CONNECTING THE SERIES 2
(SINGLE USE) 1. Remove the left Series 2 from the chargingcase 2. Hold down the multi-function button for 6 seconds 3. After a short beep the switched on Series 2 will now search for a Bluetooth device 4. Turn on the Bluetooth on your device 5. Select the option S.2 6. Once the connection has been achieved your Bluetooth status will display as Connected and an audio message of Connected will be transmitted by the Series 2 AUTOMATICALLY RECONNECT THE SERIES 2 1. Ensure that the Bluetooth is activated on the device that you have previously connected with the Series 2 2. The device must be within 10 meters of the Series2 3. Press and hold the multi-function button on both Series 2 for 6 seconds 4. Both earbuds will automatically connect with each other (youll hear a beep) 5. The Series 2 will now search for a Bluetooth device which they have previously been connectedto 6. The Series 2 will now automatically connect to your Bluetooth device ANSWER CALL 1. When a call is incoming, please press the multi-
function key to answer the call 2. Press the multi-function key to end the call Please note if you experience a slight echo at a high volume then you may have to turn the volume downslightly. REJECT A CALL 1. When a call is incoming, please press and hold the multi-function key to reject the call 2. Once the call is rejected, press the multi-function key to return to music listening mode LISTENING TO MUSIC 1. Press the multi-function key to play/pause yourmusic 2. Press and hold the multi-function key to return to the previous song 3. Double click the multi-function key to listen to the next song RESETTING THE SERIES 2 TO RECONNECT BOTHEARBUDS 1. Make sure that both Series 2 are turned off by pressing and holding both earbuds for 3 seconds 2. Go to Settings > Bluetooth and press next to the name S.2 and tap on Forget thisdevice HOW TO CHARGE THE SERIES 2 1. Put the Series 2 in the charging case 2. The activation of a red light on the front of the charging case indicates that each Series 2 is being charged 3. Sometimes one of the Series 2 will take slightly 3. Press and hold the multi-function button on both longer to charge than the other earbuds for 5 seconds 4. When the right lights turn off it means that 4. You will hear a rising tone, followed by a searching charging has completed tone in both earbuds 5. The earbuds are now searching for each other 6. Press the multi-function button on both earbuds twice to reconnect them 7. After a couple of seconds the earbuds will connect with each other (youll hear a Beep) 8. The Series 2 will now search for a Bluetoothdevice 9. Go to Settings > Bluetooth and press S.2 to connect them to your device TURNING OFF THE SERIES 2 1. Place both Series 2 in the charging case Or 2. Press and hold the multi-function button for 3seconds. 5. When you place the Series 2 in the charging case and the lights on the front dont turn on, it means that the charging case battery is empty 6. It takes approximately 50 minutes to fully charge the charging case HOW TO CHARGE THE CHARGING CASE 1. Charge the charging case by connecting the USB cable provided into the slot on the rear of the case 2. When the red light on the back of the case stops flashing it means that the charging case is fullycharged GENERAL INFORMATION PRODUCT DISPOSAL INSTRUCTIONS WARNING GUARANTEE Your Series 2 are guaranteed for a period of 6 months from date of purchase. Subject to the terms below, the guarantee will provide for the repair or replacement of the Series2 or any components thereof, which is identified as faulty or below standard, or as a result of inferior workmanship or materials. The conditions of this guarantee are:
The guarantee shall only apply to defects that occur within the 6 month guarantee period Proof of purchase is required The Series 2 are returned to ESC Sounds asinstructed This guarantee does not cover any faults or defects caused by accidents, misuse, fair wear and tear, neglect, tampering with the equipment, or any attempt at adjustment or repair other than through approved agents. The symbol shown here and on the product packaging means that the product is classed as Electrical or Electronic Equipment and should not be disposed with other household or commercial waste at the end of its working life. The waste of Electrical or Electronic Equipment
(WEEE) Directive (2002/96/EC) has been put in place to recycle products using best available recovery and recycling techniques to minimise the impact on the environment, treat any hazardous substances and avoid the increasing landfill. PRODUCT DISPOSAL INSTRUCTIONS FOR RESIDENTIAL USERS When you have no further use for it, please dispose of them and the product as per your local authoritys recycling processes. For more information please contact your local authority. This product has an IPX4 waterproof rating, which is covered under the manufacturer s warranty. PRODUCT DISPOSAL INSTRUCTIONS FOR BUSINESSUSERS This guarantee does not affect your statutory rights. Please retain this document as it acts as a guaranteecertificate. Business users should contact their suppliers and check the terms and conditions of the purchase contract and ensure that this product is not mixed with other commercial waste for disposal. Listening to earphones with the volume too high can harm your hearing Keep this product away from children Please do not attempt to make any modifications to or attempt to disassemble this product Do not expose to extreme temperatures Never attempt to use the Series 2 while in charging mode Never attempt to clean this product when in chargingmode Always ensure you are aware of your surrounding when using this product We cannot guarantee that this product will always remain securely in your ears Great care should be taken if ever handling any heavy objects while using/wearing this product and this is done entirely at the users own risk This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be u sed in portable exposure condition without restriction FCC ID: 2ARU2ST-BE18