Icontrol One Link CH-1000 User Guide i Table of Contents CHAPTER 1 INTRODUCTION ......................................................................................... 1 Package Contents.......................................................................................................... 1 Features......................................................................................................................... 1 LEDs ............................................................................................................................. 2 CHAPTER 2 INITIAL INSTALLATION........................................................................... 4 Requirements................................................................................................................ 4 Procedure...................................................................................................................... 4 APPENDIX A SPECIFICATION ........................................................................................ 5 Icontrol One Link ......................................................................................................... 5 Regulatory Approvals................................................................................................... 5 Copyright 2015. All Rights Reserved. Document Version: 1.1 All trademarks and trade names are the properties of their respective owners. ii Chapter 1 Introduction 1 This Chapter provides an overview of the Icontrol One Link's features and capabilities. Congratulations on the purchase of your new Icontrol One Link. This device is a primary controller and gateway, which includes Wi-Fi and Z-Wave home automation radios, provid-
ing connectivity to security systems and devices (including cameras and sensors). Package Contents The following items should be included:
The Icontrol One Link Unit x 1 Ethernet Cable x 1 Quick Installation Guide If any of the above items are damaged or missing, please contact your dealer immediately. Features MT7620A processor with128MB Flash and 128MB SDRAM One Ethernet port with RJ45 connector Front panel LEDs Z-Wave transceiver WPS button Reset button AC power plug (US) Internal antenna for Wi-Fi and Z-Wave 1 LEDs Top-mounted LEDs The Icontrol One Link has four LEDs. Service Wi-Fi Z-Wave POWER On (Green) - The CPE device is activated in iControl network. Off - The CPE device is not activated in iControl network. Flashing - The CPE device can not communicated with iControl network. On - Wi-Fi device attached. Off - Wi-Fi connection is not available or no Wi-Fi device at-
tached. Flashing - WPS function is activated. On (Green) - Z-Wave devices attached. Off - Z-Wave function disabled, or no Z-Wave devices attached. On (Green) - Power On/Normal operation Off - Power Off Flashing - Learn/exclusion/inclusion mode on. Flashing - Booting or Firmware upgrade. 2 Rear/Side Panel WPS Button RESET ETHERNET Port Ethernet Activi-
ty/Link LED Use a clip to press the WPS button on the device and on your other wireless device to perform WPS function that easily creates an encryp-
tion-secured wireless connection automatically. This button has two (2) functions:
Reboot. When pressed and released, the Icontrol One Link will reboot (restart). Clear All Data. This button can also be used to clear ALL data and restore ALL settings to the factory default values. To Clear All Data and restore the factory default values:
1. Power On. 2. Use a clip to press the Reset button and keep holding for 15 seconds. 3. Release the Reset Button. The Icontrol One Link is now using the factory default values. Use standard LAN cable (RJ45 connector) to connect your router to the port. On - Ethernet connection established, but the connection is idle. Off - Ethernet connection is not available. Blink - Data is being transmitted or received via Ethernet connec-
tion. 3 2 Chapter 2 Initial Installation This Chapter covers the installation of the Icontrol One Link. Requirements Use a standard 10/100BaseT network (UTP) cable with RJ45 connector. Procedure 1. Choose an Installation Site Select a suitable place to install the Icontrol One Link. 2. Connect LAN Cable Use standard LAN cable to connect the router and the Ethernet port on the Icontrol One Link. 4. Power Up Plug the Icontrol One Link into an outlet or extension cord. 5. Check the LEDs The POWER LED should be ON. The Service LED should be ON. 6. Connect Other Devices Use the Icontrol One Link as a network coordinator to connect certified Z-Wave sensors and home surveillance devices. 4 Appendix A Specification Icontrol One Link A Model Dimensions Operating Temperature Storage Temperature Network Protocol Network Interface LEDs LAN LEDs Antenna Power Adapter CH-1000 97mm(W) * 60mm(D) * 40mm(H) (without plug) 0 C to 40 C
-20 C to 70 C TCP/IP 1 * 10/100BaseT (RJ45) WAN Port 4 2 2 * Wi-Fi Internal Antennas 1 * Z-Wave Internal Antenna AC Input 120V with US Plug Regulatory Approvals FCC Statement This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
(Example - use only shielded interface cables when connecting to computer or peripheral devices). 5 FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 6