TouchSecure Connectivity User Manual Ver2.0 TouchSecure Connectivity User Manual Version History Date 22-May-13 17-Jul-13 Version 1.0 2.0 Description of Changes Initial version 1. ICES-003 Statement removed. 2. French translation added for RSS-GEN 3. Added FCC statement Author Sixtus Sixtus IDT.QM.P2.T1.DT Printed copies of this document are uncontrolled Ver1.0 Page 2 of 11 Internal Use Only TouchSecure Connectivity User Manual Contents 1.0 Introduction ................................................................................................................................ 4 2.0 Reader ......................................................................................................................................... 4 Functionality .............................................................................................................................. 4 TouchSecure reader with Casing .......................................................................................... 4 Back Plate ................................................................................................................................. 5 Product details ........................................................................................................................... 5 2.1 2.2 2.3 3.0 4.0 Specifications ............................................................................................................................. 5 5.0 5.3.1 5.3.2 Installation details ...................................................................................................................... 6 5.1 Parts List ................................................................................................................................... 6 5.2 Recommended Infrastructure ................................................................................................... 6 5.3 Wiring Information ..................................................................................................................... 6 Cable Color codes for Pig Tail Reader .............................................................................. 6 Pin out for Phoenix Connector Reader ............................................................................. 7 5.4 Mounting the Reader ................................................................................................................ 8 Location of mounting holes on wall ................................................................................... 8 Reader Installation Steps .................................................................................................. 8 Power up and Testing ............................................................................................................. 10 6.0 Certifications ............................................................................................................................ 10 FCC ........................................................................................................................................ 10 6.1 6.2 IC ............................................................................................................................................ 10 6.3 CE ........................................................................................................................................... 11 5.4.1 5.4.2 5.5 IDT.QM.P2.T1.DT Printed copies of this document are uncontrolled Ver1.0 Page 3 of 11 Internal Use Only TouchSecure Connectivity User Manual Introduction 1.0 This document details the Physical Access Control Reader TouchSecure and its basic operational and Model: Connectivity WM The reader comes in two variants for interfacing with the control panel installation procedures. the details of the Wallmount form-factor It covers reader Pigtail Phoenix connectors 2.0 Reader Functionality 2.1 TouchSecure is a physical access reader that can read HF and LF contactless credentials .The reader can interface with an access control system equipped with a Wiegand or RS485 serial interface Control Panel. It can also be interfaced with a Host Sever / Control Panel that supports Ethernet interface. User interfaces include RGB LEDs and Buzzer. The reader consists of the following main parts. 2.2 TouchSecure reader with Casing IDT.QM.P2.T1.DT Printed copies of this document are uncontrolled Ver1.0 Page 4 of 11 Internal Use Only TouchSecure Connectivity User Manual 2.3 Back Plate 3.0 Product details Model Name Device Type Type of equipment Interface Type Voltage Rating Current Rating @12V Communication protocol 4.0 Specifications
: Connectivity WM
: RFID reader, 13.56MHz (HF) / 125 KHz (LF) Physical Access control Reader (accessory equipment)
: Potted reader. Suitable for Indoor / Controlled Outdoor use
: Pigtail Cable (11 Core + Drain) or Phoenix connectors and RJ45
: 5-16V DC or 48VDC on RJ45 Connector
: Pk Current 180mA , Average Current 120mA
: Wiegand, RS485 (2wire - Half Duplex) , 10BaseT ETH Model Op Voltage Current @ 12V Op temp Cable Length Connectivity WM 5-16 VDC or POE@ 48VDC Av -120mA Pk -180mA
-35 to +65 Deg C RS485 - 4000ft (24AWG) Wiegand -500ft (22AWG)/
300ft (24AWG) Table 1 IDT.QM.P2.T1.DT Printed copies of this document are uncontrolled Ver1.0 Page 5 of 11 Internal Use Only TouchSecure Connectivity User Manual 5.0 Installation details Parts List 5.1 TouchSecure reader -1 Screws (A #6-18X1.5" SS ) - 4Nos Back Plate mounting screws for Wall Snake Eye Screw (SMF #6-32X5/16" SS) 1 No- Top casing mounting security screw Screws (SMF #6-32x3/8" SS) - 3 Nos - 1 casing to back plate mounting screw and 2 Junction Box mounting screws Nylon anchor plug -4 Nos 6 pin phoenix plug (Phoenix connector version only) 2 Nos Back Plate 5.2 Recommended Infrastructure Cable Wiegand - 22AWG for 500Ft / 24AWG for 300Ft with Foil Shield Cable RS485 Cable RJ45 Linear DC PS POE Adaptor Kit - TL-POE200A
- RS485 for 1000m** (4000ft) 24AWG STP
- Cat5e / Cat6
- 5-16 V, 1A min.
** Tested in lab conditions upto 115Kbaud 5.3 Wiring Information
+ VDC 12V (nominal) Ground Wiegand Data 0 Wiegand Data 1 LED Green Buzzer Hold LED Red RS485 -
RS 485 +
Tamper Output Shield Ground 5.3.1 Cable Color codes for Pig Tail Reader Red &
Black & White Green White Orange Yellow Blue Brown Grey Pink Violet Black / Drain Table 2
& - Do not connect when reader is powered by Power over Ethernet IDT.QM.P2.T1.DT Printed copies of this document are uncontrolled Ver1.0 Page 6 of 11 Internal Use Only TouchSecure Connectivity User Manual 5.3.2 Pin out for Phoenix Connector Reader Comment Cable colour Description LED Green Orange White Green Black Data 1 Data 0 Drain Gnd Power Hold Tamper RS485-
RS485+
Buzzer LED Red Red Blue Violet Gray Pink Yellow Brown Do not connect when reader is powered by PoE Pin P1.1 P1.2 P1.3 P1.4 P1.5 Black + White P1.6 P2.1 P2.2 P2.3 P2.4 P2.5 P2.6 Table 3 Caution:
During Wiring make sure that the +VDC lines does not make contact with any other cables, as it might affect reader functionality/ cause damage to the reader. IDT.QM.P2.T1.DT Printed copies of this document are uncontrolled Ver1.0 Page 7 of 11 Internal Use Only TouchSecure Connectivity User Manual 5.4 Mounting the Reader Location of mounting holes on wall 5.4.1 Phoenix connector Reader 4 Holes and 1 Slot Reader Installation Steps 5.4.2 Insert the nylon screw plugs into the wall. a. Make holes on the wall as per the image above. b. c. Connect the wires as per the Table 2 or Table 3. d. TouchSecure reader with Bottom Casing is to be now secured onto the wall using the Screws (A #6-18X1.5" SS ) e. The top casing can be inserted onto the bottom casing f. Secure the Top and bottom casing by the Snake Eye Screw (SMF #6-32X5/16" SS) IDT.QM.P2.T1.DT Printed copies of this document are uncontrolled Ver1.0 Page 8 of 11 Internal Use Only TouchSecure Connectivity User Manual Reader Installation Steps - Phoenix Connector Version Reader Installation Steps - Pig Tail Version IDT.QM.P2.T1.DT Printed copies of this document are uncontrolled Ver1.0 Page 9 of 11 Internal Use Only TouchSecure Connectivity User Manual 5.5 Power up and Testing 1 2 Turn power on The LED blinks 3 times green with a long beep, then turns red Present a card The LED blinks green, and a short Beep is emitted This is the default reader behavior. 6.0 Certifications 6.1 FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Information to user Changes or modifications not expressly approved by Identive could void the user's authority to operate the equipment. 6.2 IC This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement IDT.QM.P2.T1.DT Printed copies of this document are uncontrolled Ver1.0 Page 10 of 11 Internal Use Only TouchSecure Connectivity User Manual 6.3 CE Identive hereby declares that the TouchSecure Model: Connectivity WM device mentioned herein is in compliance with the essential requirements and other relevant portions of the Directive R&TTE 1999/5/EC. IDT.QM.P2.T1.DT Printed copies of this document are uncontrolled Ver1.0 Page 11 of 11 Internal Use Only