INSTALLATION & SETUP GUIDE FOR SINGLE POLE & 3-WAY CONFIGURATIONS IN WALL SOLUTIONS 1 Router Security Settings Supported: WPA, WPA2, or None REQUIRES Wi-Fi 2.4 GHz 802.11 b/g/n compatible network Free iDevices Connected App 120VAC Line and Neutral wires in each gang box HomeKit requires an iPhone, iPad or iPod touch with iOS 9.0 or later Android 4.3+ devices with Bluetooth Smart technology TOOLS NEEDED Philips Screwdriver Pliers Wire Cutter/Stripper Voltage Detector Flathead Screwdriver RATINGS Input: 125-277VAC, 60Hz Output: 125-277VAC, 60Hz Resistive: 1800W @ 120-277VAC Tungsten: 960W @ 120VAC Tungsten: 1800W @ 277VAC Motor: 1HP @ 120-277VAC Ballast: 10A @ 277VAC 2 Not intended for critical medical or life support equipment. Use caution when using the iDevices Wall Switch to control any appliances which produce heat or mechanical motion, or could create a hazardous condition when operated while unattended. The iDevices Wall Switch is not user-serviceable. Do not attempt to open the enclosure for any reason. The iDevices Wall Switch is only for installation with copper or copper-clad wires. Do not install in a circuit that uses aluminum wires. The iDevices Wall Switch must be installed in a manner that conforms to all applicable national, state, and local building codes. The iDevices Wall Switch is intended for dry, indoor use only. Use with branch circuit breaker 20A or less.
!
RISK OF ELECTRIC SHOCK, SEVERE BURNS, AND FIRE: Your safety is important to us. Electricity is dangerous and can cause personal injury and property damage if handled improperly. A working knowledge of electrical installation is required to install this product. If you are not comfortable working with electricity do not attempt to install the iDevices Wall Outlet and seek professional assistance from a qualified electrician. 3 BEFORE YOU START Read through this Installation Guide in its entirety before starting installation of your iDevices Wall Switch or removal of your old switches. Incorrect installation can be dangerous and can damage your iDevices Wall Switch or your home. The iDevices Wall Switch is intended to be installed by a qualified electrician. Visit our YouTube channel for tips on installation and setup:
www.youtube.com/user/iDevicesInc Turn OFF the power to the circuit you are working on at your homes breaker or fuse panel. 4 Where ever possible, install the iDevices Wall Switch in a non-
metallic gang box and use a non-metallic faceplate, as metal gang boxes and faceplates can decrease the Wi-Fi signal strength. Check that your mobile device is compatible with the iDevices Wall Switch at iDevicesinc.com/Compatibility It is YOUR responsibility to be sure that products are installed in accordance with applicable building codes. Check with your local building office if you have questions. Download the Free iDevices Connected app. For 4-way configurations, visit:
iDevicesinc.com/Support/WallSwitch/Setup 5 GETTING TO KNOW THE iDEVICES WALL SWITCH 1 2 Turn Light On. Used also for 3-way, 4-way pairing. Turn Light Off. Used also for connecting to the Wi-Fi network. Status LED/Night Light. Provides setup status and used as a night light during operation. Refer to LED color codes on page 42. Pull Out Tab. Refer to this when prompted to enter your HomeKit setup code during the setup on a iOS device. Also used to document the Wall Switch as the Primary or Secondary in a 3-way or 4-way configuration. Device Reboot. Pressing this cycles power to the device. 3 4 5 6 6 Pairing Setup Button. Used to wireless pair between multiple Wall Switches for 3-way and 4-way configurations and for connecting to the Wi-Fi network. DEVICE RESET: Press and hold for 10 seconds until LED blinks red. 1 3 2 6 4 5 7 INSTALLATION - SINGLE POLE STEP 1 Turn off the power at the circuit breaker. STEP 2 Remove the existing switch from the gang box. STEP 3 Confirm that each gang box contains a neutral wire (typically white). If there are no neutral wires present, you may need to run additional wires, please consult a qualified electrician. GROUND NOTE: Your homes wiring may differ; please consult a qualified electrician. 8 NEUTRAL LOAD LINE LOAD LINE 9 STEP 4 Remove both wires from the terminals of the existing switch and cap with the provided wire nuts. Note: If you have more than 2 wires connected to your switch (not including the bare copper or green-coated ground wire), please see the 3-way, 4-way installation instructions. It is not necessary to remove the ground wire. NEUTRAL LOAD LOAD LINE LINE GROUND 10 11 STEP 5 Turn the power back On at the breaker. Using your voltage detector, identify which of the 2 wires you removed is energized. This is the Line wire. The wire that is not energized is the Load wire. Note these two wires for future reference. LOAD NEUTRAL LOAD GROUND LINE LINE 12 13 STEP 6 Turn the power back Off at the breaker and install the iDevices Wall Switch according to the diagram. Ensure all wire nuts are securely fastened. NEUTRAL LOAD LOAD LINE 14 GROUND LINE 15 STEP 7 Install the Wall Switch into the gang box and install the faceplate. STEP 8 Turn the power back On at the circuit breaker and confirm that the LED on the Wall Switch lights up purple. LED will light up purple 16 17 WIRELESS COMMUNICATION SETUP STEP 1 Ensure power/breaker is turned back on and the LED on the Wall Switch is solid purple. STEP 2 Press and hold 6 for 5 seconds and release when the LED rapidly flashes blue. Next tap 2 to begin the Wi-Fi connection process. Ensure LED is purple 2 6 18 19 STEP 3 Launch the iDevices Connected app and you will be guided through the process of connecting your Wall Switch. For iOS devices, you will need the HomeKit setup code on the pull out tab on your Wall Switch. Wall Switch - Model: IDEV0008 XXX-XX-XXXX Primary Secondary XXX-XX-XXX Connected App Icon Basic One Color Icon Pull out tab HomeKit setup code is located on the pull out tab of the iDevices Wall Switch. Optimized Small Versions
.75pt Additional
.5pt Additional 20 21 INSTALLATION - 3-WAY STEP 1 Turn off the power at the circuit breaker. STEP 2 Remove the existing switches from the gang boxes. STEP 3 Confirm that each gang box contains a neutral wire (typically white). If there are no neutral wires present, you may need to run additional wires, please consult a qualified electrician. NOTE: Your homes wiring may differ; please consult a qualified electrician. 22 LINE LOAD COMMON NEUTRAL NEUTRAL TRAVELER TRAVELER GROUND GROUND COMMON 23 STEP 4 Remove the wires from the Common terminal on both of the existing switches and cap with the provided wire nuts. Note: The common terminals usually have a screw that is either black or copper in color. 24 LINE LOAD COMMON NEUTRAL NEUTRAL TRAVELER TRAVELER GROUND GROUND COMMON 25 STEP 5 Turn the power back on at the breaker. Using your voltage detector, identify which of the 2 common wires you removed is energized. This is the line wire. Mark this wire as the Secondary (S) Switch Position. You will need to refer to this during the Pairing and Setup Process. The common wire that is not energized is the load wire. Mark as the Primary (P) Switch Position. You will need to refer to this during the Pairing and Setup Process. GROUND LINE LOAD COMMON NEUTRAL S NEUTRAL P TRAVELER TRAVELER GROUND 26 COMMON 27 STEP 7 Install the iDevices Wall Switches according to the diagram. Ensure the wire nuts are securely fastened. SECONDARY SWITCH LINE LOAD PRIMARY SWITCH NEUTRAL S COMMON NEUTRAL TRAVELER TRAVELER P LOAD LINE GROUND GROUND 28 Ensure you install a wire nut on the red lead on the secondary switch as well as on both ends of the traveler wire (typically red wire) 29 STEP 8 Install the Wall Switches into the gang boxes. STEP 9 Extend the pull out tab on the front of the Wall Switch connected to the Line wire (identified in step 5), Using a pen, put a X in the box on to indicate that this is the Secondary Switch. Pull out tab Wall Switch - Model: IDEV0008 XXX-XX-XXXX Primary Secondary 30 31 STEP 10 Extend the pull out tab on the front of the Wall Switch connected to the Load wire (identified in step 5), Using a ball point pen, put a X in the box on to indicate that this is the Primary Switch. Wall Switch - Model: IDEV0008 XXX-XX-XXXX Primary Secondary STEP 11 Turn the power back on at the circuit breaker and confirm that the LED on both Wall Switches light up purple. 32 Ensure LED is purple on BOTH Wall Switches 33 WIRELESS COMMUNICATION SETUP The wireless setup is a 2 step process for a 3-way Switch configuration. First you will pair the Primary Switch to the Secondary Switch, then you will add the Primary Switch to your Wi-Fi network. PAIRING THE PRIMARY TO THE SECONDARY SWITCH STEP 1 Ensure power/breaker is turned back on and the LED on both Wall Switches are solid purple. Ensure LED is purple on BOTH Wall Switches 34 35 STEP 2 Locate the primary Switch. Hold 6 until the LED rapidly flashes blue (5 sec) then release. Next tap 1 to enter pairing mode. The LED will flash blue slowly. Next Locate the secondary Switch. Repeat the steps above on the Secondary Switch by holding 6 until the LED rapidly flashes blue
(5 seconds) then release. Next tap 1 to begin the pairing mode. The LED will flash blue slowly. The secondary Wall Switch will search and pair to the primary switch. The LED on each Wall Switch will rapidly blink green 5 times and each Wall Switch will beep 5 times to indicate the pairing process is complete. 1 6 36 37 CONNECTING TO THE WIRELESS NETWORK STEP 1 On the Primary switch press and hold 6 for 5 seconds and release when the LED rapidly flashes blue. Next Tap 2 to begin the Wi-Fi connection process. Ensure LED is purple 2 6 38 39 STEP 2 Launch the iDevices Connected app and you will be guided through the process of connecting your wall switches. For iOS devices, you will need the HomeKit setup code on the pull out tab of your Primary Wall Switch. Connected App Icon Basic One Color Icon Pull out tab Wall Switch - Model: IDEV0008 XXX-XX-XXXX Primary Secondary Wall Switch - Model: IDEV0008 XXX-XX-XXXX Primary Secondary HomeKit setup code is located on the pull out tab of the iDevices Wall Switch. Optimized Small Versions
.75pt Additional
.5pt Additional 40 41 REFERENCE INFORMATION LED COLOR CODES LED State Description Blue Flashing Solid Blue Wall Switch is waiting for the handset to configure the accessorys Wi-Fi. The LED flashs blue. Wall Switch is waiting for the handset to initiate and complete pair set up through either Wi-Fi or BLE (Bluetooth Low Energy). The LED is solid blue. Slow Blue Flash Pairing mode has expired and Wall Switch is waiting for the user to press the Pairing Button 6 down for about 3 seconds to reenter pairing mode. The LED slowly flashes blue. Solid Blue To reinitiate the pairing mode, hold the Pairing Button 6 down for 3 seconds and the LED will turn solid blue. LED State Description Green Flash Orange Flash Red Flash Purple Flash When Wall Switch joins a Wi-Fi network, (i.e., the link is up) the LED flashes green for 1 second. When Wall Switch has lost the connection to the Wi-Fi network, (i.e., the link is down) the LED slow flashes orange until the link is up. To initiate a device reset, which will clear all Wi-Fi and pairing information, hold the Pairing Button 6 down for 10 seconds until the LED rapidly flashes red. When the button is released the unit will reboot and reenter the pairing mode. When Wall Switch receives a request to identify itself, it rapidly flashes purple. 42 43 SUPPORT If at any time you require assistance, please contact our Customer Experience Team. Call: 888.313.7019 Email: Support@iDevicesinc.com Visit: iDevicesinc.com/Support 44 45 REGULATORY INFORMATION Product Information:
Manufacturer: iDevices LLC Model: IDEV0008 FCC: 2ABDJ-SWITCH8 IC: 11569A-SWITCH8 The iDevices Wall Switch IDEV0008 is certified to comply with applicable FCC and IC rules and regulations governing RF and EMI emissions. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
46 47 Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician to help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment IC Notice This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-
003 du Canada. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den 48 compromettre le fonctionnement. This device complies with the Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. References Requires the iDevices Connected app. For warranty information please visit iDevicesinc.com/Warranty. 49 Apple, the Apple logo, iPhone, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. HomeKit is a trademark of Apple Inc. Controlling HomeKit-
enabled accessories away from home requires an Apple TV (3rd generation or later) with Apple TV software 7.0 or later and an iPhone, iPad, or iPod touch with iOS 8.1 or later. Amazon, Echo, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Android is a trademark of Google Inc. Google Play and the Google Play logo are trademarks of Google Inc. 50 51