FCC ID: UFW-CHASERXR Chaser XR GPR CHASERXR

Chaser XR Version 001 User Manual IDS Geo ORIGINAL INSTRUCTION IN ENGLISH LANGUAGE MNG/2023/007 Rev. 1.0 July 2023 User Manual Chaser XR Ver. 001 User Manual Mod: MDM/011/M2 Rev8 IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 2/ 41 Chaser XR Ver. 001 User Manual Mod: MDM/011/M2 Rev8 LEGAL NOTICE Use of the Manual This Manual is intended to be used solely by authorized user of IDS GeoRadar Systems. It is specific for internal business purpose only. If you are not an authorized user, you are NOT allowed to read this Manual and you must return it to IDS GeoRadar as soon as possible. Access to and use of this Manual is also provided subject to the acceptance of the Disclaimer set out below. Disclaimer About the Manual This Manual has been drafted by IDS GeoRadar with the due care in order to ensure the accuracy and completeness. However, please note that no warranty is provided about the fact that the Manual will be free from error or omission and about the accuracy and/or fitness to the purpose of any information contained herein. Any representation and/or statement contained herein has been written in good faith and on the basis that, due to negligence, lack of care or otherwise, IDS GeoRadar is not liable for any loss, including direct, indirect or consequential losses, in contract or in tort for any misstatement or omission contained herein which has occurred or may occur with reference to any representation and/or statement contained in the Manual. User shall also acknowledge that some information contained in the Manual may not be up to date. IDS GeoRadar may amend the information contained in the Manual from time to time and IDS GeoRadar shall not be deemed liable in the event that damages arise with reference to changed circumstances or other information which may affect the accuracy of any information contained in this version of the Manual. About the Product All products designed, produced and distributed by IDS GeoRadar, its Subsidiaries, Affiliated and authorized Distributors (Products) shall not be used, in the design, development, production or use of chemical, biological, nuclear ballistic weapons. Buyer/ User will defend, indemnify and hold IDS GeoRadar harmless against any liability (including attorneys fees) for non-compliance with the terms of this paragraph. If IDS GeoRadar requires that Buyer/User shall carry out a training with reference to some Product categories, no operation or use of the Products shall be started before its designated Operator/s has got the User Certificate, as defined by IDS GeoRadar specific procedure which the Buyer confirms to know and accept. For Products which include specific Operational software with automatic data processing and analysis Tools, e.g. RockSpot, IBIS Products; Hydra Products, User shall be aware that the results provided by these Tools may be not error free. User that completely relies on the outcomes provided by these Tools only, does it at his own risk. In no event IDS GeoRadar shall be liable for special, direct, indirect, incidental, exemplary, punitive or consequential damages including, but not limited to, loss of profits or revenue, caused by the missed or incomplete observance of the instructions and prescriptions for the use of the Products, either separately or in combination with other products. This paragraph provides only a non-exhaustive summary of the full Product disclaimer. Please see the full Product disclaimer included into the relevant section of this Manual for detailed information. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 3/ 41 INDEX INDEX Mod: MDM/011/M2 Rev8 1 Table of Contents INTRODUCTION .......................................................................................................................................................................................................................................... 6 1.1 1.2 1.3 1.4 PURPOSE .......................................................................................................................................................................................................................................................... 6 APPLICATION FIELD ............................................................................................................................................................................................................................................. 6 INTENDED READERSHIP ........................................................................................................................................................................................................................................ 6 AUTHORIZATION OF USE ...................................................................................................................................................................................................................................... 6 1.4.1 CE Marking ................................................................................................................................................................................................................................................ 7 1.4.2 UKCA Marking ........................................................................................................................................................................................................................................... 7 2 HOW TO READ THE MANUAL ..................................................................................................................................................................................................................... 7 2.1 2.2 2.3 MANUAL LAYOUT ............................................................................................................................................................................................................................................... 7 SYMBOLS .......................................................................................................................................................................................................................................................... 7 GLOSSARY & ACRONYMS ..................................................................................................................................................................................................................................... 8 3 SAFETY DIRECTIONS ................................................................................................................................................................................................................................... 8 3.1 3.2 3.3 3.4 3.5 3.6 DESCRIPTION ..................................................................................................................................................................................................................................................... 8 INTENDED USE ................................................................................................................................................................................................................................................... 8 REASONABLY FORESEEABLE MISUSE ....................................................................................................................................................................................................................... 8 LIMITS OF USE ................................................................................................................................................................................................................................................... 9 RESPONSIBILITIES ............................................................................................................................................................................................................................................... 9 HAZARD OF USE ............................................................................................................................................................................................................................................... 10 4 GENERAL DESCRIPTION .............................................................................................................................................................................................................................13 4.1 DELIVERY CONTENTS ......................................................................................................................................................................................................................................... 13 4.1.1 Chaser XR Lite Pack (989791) .................................................................................................................................................................................................................. 13 4.1.2 Chaser XR Drag Kit (989754, optional) .................................................................................................................................................................................................... 14 4.1.3 Chaser XR Positioning Kit (986689, Optional) ......................................................................................................................................................................................... 15 BASIC SYSTEM COMPOSITION ............................................................................................................................................................................................................................. 15 ACCESSORIES ................................................................................................................................................................................................................................................... 16 4.3.1 Chaser XR Drag Kit (optional).................................................................................................................................................................................................................. 16 4.3.2 Chaser XR Positioning Kit (optional) ........................................................................................................................................................................................................ 16 BATTERY HANDLING ......................................................................................................................................................................................................................................... 17 4.4.1 Charging .................................................................................................................................................................................................................................................. 17 4.2 4.3 4.4 IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 4/ 41 INDEX Mod: MDM/011/M2 Rev8 4.5 4.4.2 Operation/Discharging ........................................................................................................................................................................................................................... 17 Storage .................................................................................................................................................................................................................................................... 17 4.4.3 GNSS REQUIREMENTS ...................................................................................................................................................................................................................................... 17 4.5.1 How to connect Chaser XR to a GNSS ..................................................................................................................................................................................................... 17 4.5.2 How to connect Chaser XR to a TPS ........................................................................................................................................................................................................ 17 5 HOW TO SET UP CHASER XR ......................................................................................................................................................................................................................18 5.1 5.2 5.3 HOW TOSET UP CHASER XR LITE....................................................................................................................................................................................................................... 18 HOW TOSET UP CHASER XR DRAG KIT (OPTIONAL) .............................................................................................................................................................................................. 20 HOW TOSET UP CHASER XR POSITIONING KIT (OPTIONAL) .................................................................................................................................................................................... 22 6 HOW TO WORK ON SITE WITH CHASER XR ................................................................................................................................................................................................22 6.1 6.2 6.3 6.4 6.5 6.6 HOW TO SET UP CHASER XR IN HH OR VV POLARIZATION ....................................................................................................................................................................................... 22 HOW TO CONNECT THE FIELD PC AND THE CHASER XR ANTENNA ............................................................................................................................................................................... 22 HOW TO COLLECT CHASER XR DATA IN ENCODER MODE .......................................................................................................................................................................................... 25 HOW TO COLLECT CHASER XR DATA IN GRID MODE ............................................................................................................................................................................................... 26 HOW TO COLLECT CHASER XR DATA IN GNSS MODE ............................................................................................................................................................................................... 27 HOW TO COLLECT CHASER XR DATA IN TPS MODE ................................................................................................................................................................................................. 28 7 CARE AND TRANSPORT .............................................................................................................................................................................................................................30 7.1 7.2 7.3 7.4 CLEANING INFORMATION ................................................................................................................................................................................................................................... 30 BATTERY REMOVAL INFORMATION ...................................................................................................................................................................................................................... 30 PERIODICAL CHECK ........................................................................................................................................................................................................................................... 31 PROPER SYSTEM USE AND TRANSPORT/SHIPPING .................................................................................................................................................................................................... 31 8 IDS GEORADAR SUPPORT ..........................................................................................................................................................................................................................32 8.1 8.2 MYWORLD ...................................................................................................................................................................................................................................................... 32 HOW TO MANAGE RETURN FOR SERVICE ............................................................................................................................................................................................................... 32 IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 5/ 41 1 INTRODUCTION 1 INTRODUCTION This document describes the Chaser XR system, that is a dual frequency GPR system by IDS GeoRadar. This document refers to the concepts the user must learn before initiating the utilization of this device. Therefore, it is mandatory to carefully reading the entire document before starting and operating the system. 1.1 Purpose The purpose of this document is to drive the reader to a list of actions to install and use the Chaser XR system, in a thorough and safe way. The structure of the manual is organized in a collection of "how-to" as well as descriptive chapters. Each chapter contains the illustration and basic description, of the main operations to be carried out for system installation and use on field. 1.2 Application field The main application of Chaser XR is the collection of GPR data over areas of variable extension, and for applications including, but not limited to, glaciology, environmental, archaeology, geology, geotechnic. Also, any type of buried objects or structures may be the aim of the system if these are buried within its depth of reach. 1.3 Intended readership The intended Reader of this manual should be the technician in charge of using the system that has undergone the IDS GeoRadar training for Chaser XR. Mod: MDM/011/M2 Rev 8 1.4 Authorization of use https://www.anfr.fr/en/broadcasting-authorisation/reseaux-

The use of Chaser XR system may be subject to a license and/or an authorization by the Competent Ministry of the country where the system will be used. An individual license and restrictions are in place to date in the following European countries:

France:

professionnels/les-frequences-utilisees-a-titre-temporaire/les-systemes-

dimagerie-radar-de-type-gpr-wpr/

Germany:

https://www.bundesnetzagentur.de/SharedDocs/Downloads/DE/Sachgebie te/Telekommunikation/Unternehmen_Institutionen/Technik/Inverkehrbrin genvonProdukten/Schnittstellenbeschreibungen/OrtungsfunkOR/SSBOR_N N022.pdf?__blob=publicationFile&v=4 Portugal: https://www.anacom.pt/render.jsp?categoryId=389647 Romania: https://www.ancom.ro/radio-spectrum_2749 Spain: https://www.boe.es/diario_boe/txt.php?id=BOE-A-2011-19146 Sweden:

https://www.pts.se/sv/bransch/radio/radiotillstand/ansokningshandlingar/

Liechtenstein and Switzerland:

https://www.bakom.admin.ch/bakom/en/homepage/frequencies-and-

antennas/frequency-use-with-or-without-licences/radiocommunication-

licences-in-general.html For more details with reference to the restriction, please refer to the following website: ECO Frequency Information System (cept.org) CH ES LI RO DE FR PT SE IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 6/ 41 2 HOW TO READ THE MANUAL 1.4.1 CE Marking This equipment complies with the essential requirements and other relevant provisions of Directive 2014/53/UE. The full Declaration of its Conformity can be found either on the CD or a separate document included with this product. This is a Class A product. In a domestic environment it may cause radio interference. If so, the user may need to take adequate measures. 1.4.2 UKCA Marking This equipment complies with the essential requirements of the Radio Equipment Regulations 2017 (S.I. 2017/1206). The full Declaration of its Conformity can be found either on the CD or a separate document included with this product. requirements Licensing https://www.ofcom.org.uk/manage-your-

licence/radiocommunication-licences/licensed-short-range can be in UK found here:

2 HOW TO READ THE MANUAL 2.1 Manual Layout As mentioned, this User Manual is structured in a How to manner. In each of the relevant chapter, the User shall find the basics to carry out the Chaser XR installation and use. It is strongly recommended to go through this manual thoroughly, and to read it carefully. However, as the document is divided into a first part that is descriptive of the whole system, but also into procedures that are self-

consistent, and that can be read sparsely, it is not mandatory to read this document chapter after chapter, in case of need. Mod: MDM/011/M2 Rev 8 2.2 Symbols Warning messages are an essential part of the Safety Concept of the instrument. They appear wherever hazards or hazardous situations can occur. Warning messages:

make the user alert about direct and indirect hazards concerning the use of the product. contain general rules of behaviour. For the users safety, all safety instructions and safety messages shall be strictly observed and followed. Therefore, the manual must always be available to all persons performing any tasks described herein. DANGER, WARNING, CAUTION and NOTICE has got standardized signal words for identifying levels of hazards and risks related to personal injury and property damage. For safety purposes, it is important to read and fully understand the table below with the different signal words and their definitions. Supplementary safety information symbols may be placed within a warning message as well as supplementary text. Type Description DANGER WARNING CAUTION Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation or an unintended use which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation or an unintended use which, if not avoided, may result in minor or moderate injury. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 7/ 41 3 SAFETY DIRECTIONS Mod: MDM/011/M2 Rev 8 Information symbols may be placed within a warning message as well as supplementary text.

SNR: Signal to Noise Ratio SW: Software NOTICE: Note text/to keep in mind

- UBLOX: GNSS device within the GPR system

- uMap: IDS GeoRadar software for GPR data acquisition Tip text 2.3 Glossary & Acronyms The following acronyms are used in this manual:

- Chaser XR: IDS GeoRadar GPR System

- Controller: PC / Tablet used by the user for data acquisition. The data acquisition SW (client) is performed on the controller.

EsT: Equalized Scrambled Technology FCU: Fast Control Unit

- GNSS: Global Navigation Satellite System

- GPR: Ground Penetrating Radar or Georadar or Ground Probing Radar

- HMI: Human Machine Interface

- HW: Hardware

- NMEA format: National Marine Electronics Association format

- RTK: Real Time Kinematic 3 SAFETY DIRECTIONS 3.1 Description The following directions enable the person responsible for the product, and the person who uses the equipment, to anticipate and avoid operational hazards. The person responsible for the product must ensure that all users understand these directions and adhere to them. 3.2 Intended Use The intended use of Chaser XR is the detection of underground features in diverse environmental conditions, and within the depth of reach of the system itself, including but not limited to:

Geology Geotechnical Environmental Glaciers Rivers Archaeology Forensic Buried structures, in general. 3.3 Reasonably Foreseeable Misuse Infringing traffic regulation. Use of the product without instruction. Use outside of the intended use and limits. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 8/ 41 3 SAFETY DIRECTIONS Mod: MDM/011/M2 Rev 8 Opening the product using tools, for example screwdriver, unless this To understand the safety instructions on the product and the instructions in the user manual. To ensure that it is used in accordance with the instructions. To be familiar with traffic laws and local regulations relating to safety and accident prevention. To inform IDS GeoRadar s.r.l. immediately if the product and the application becomes unsafe. To ensure that the traffic laws, the national laws, regulations, the operation of electromagnetics for and conditions transmitters are respected. NOTICE: Watch out for erroneous measurement results if the product has been dropped or has been misused, modified, stored for long periods. Precautions:

Periodically carry out test measurements, particularly after the product has been subjected to abnormal use and before and after of important measurements. is permitted for certain functions. Modification or conversion of the product. Use after misappropriation. Use of products with obvious damages or defects. Use with accessories from other manufacturers without the prior explicit approval of IDS GeoRadar s.r.l. Inadequate safeguards at the working site. 3.4 Limits of Use Environment: Suitable for use in an atmosphere appropriate for permanent human habitation. Not suitable for use in explosive environments. WARNING: POTENTIALLY HAZARDOUS AREAS working in hazardous areas, such as potentially explosive areas, or close to electrical installations, or similar situations, could result in death or serious injury. PRECAUTION: Local safety authorities and safety experts must be contacted, by the person in charge of the product on site, prior commencing any survey in potentially hazardous areas, for the due risk assessment. 3.5 Responsibilities Manufacturer of the product - IDS GeoRadar s.r.l. is responsible for supplying the product, including the user manual and original accessories, in a safe condition. Person responsible for the product - The person responsible for the product

(the user) has the following duties:

IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 9/ 41 3 SAFETY DIRECTIONS 3.6 Hazard of use WARNING: CRUSHING HANDS AND FINGERS While installing the system, the risk of fingers pinch-out, may occur. PRECAUTION: To mount the system, the user must always wear protective gloves and safety boots. WARNING: RISK OF ACCIDENTS During surveys there is a danger of accidents occurring if the user does not pay attention to the surrounding site conditions, such as obstacles, excavations, or traffic. PRECAUTIONS: During operations, the user of the product must be fully aware of the existing site conditions, and potential dangers. WARNING: ELECTROCUTION Because of the risk of electrocution, it is dangerous to use poles and extensions near electrical installations such as power cables or electrical railways. PRECAUTIONS: Keep at a safe distance from electrical installations. If it is essential to work in this environment, first contact the safety authorities responsible for the electrical installations and follow their safety instructions. Mod: MDM/011/M2 Rev 8 NOTICE: If the accessories used with the product are not properly secured and the product is subjected to mechanical shock, for example blows or falling, the product may be damaged. Precautions:

When setting-up the product, make sure that the accessories are correctly adapted, fitted, secured, and locked in position. Avoid subjecting the product to mechanical stress. WARNING: LIGHTING STRICKING If the product is used with accessories (for example GNSS pole support), the user may increase the risk of being struck by lightning. PRECAUTIONS: Do not use the product during thunderstorm. WARNING: SECURING OF THE WORKING SITE Inadequate securing of the working site can lead to dangerous situations, for example in traffic, on building sites, and at industrial installations. PRECAUTIONS: Always ensure that the working site is adequately secured. Adhere to the regulations governing safety, accident prevention, and road traffic. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 10/ 41 3 SAFETY DIRECTIONS Mod: MDM/011/M2 Rev 8 NOTICE: If the product is improperly disposed, the following can happen:

If polymer parts are burnt, poisonous gases are produced which may impair health. If batteries are damaged or are heated strongly, they can explode and cause poisoning, burning, corrosion or environmental contamination. By disposing of the product irresponsibly you may enable unauthorized persons to use in contravention of the regulations, exposing themselves and third parties to the risk of liable to severe contamination. injury and rendering the environment it RECYCLING The crossed out wheeled bin symbol shown on the equipment indicates that the product must be recycled separately from other waste at the end of its useful life. Separate waste disposal of this product at the end of its useful life will be organised and managed by IDS GeoRadar. When you decide to dispose of the equipment, contact IDS GeoRadar and follow the system that IDS GeoRadar has set up to permit the separate collection of the apparatus at its life end. Adequate separate collection for its subsequent recycling, treatment and environmentally friendly disposal contribute towards avoiding any unnecessary effects on the environment and to health and favour the reuse or recycling of the materials that make up the equipment. Unauthorised disposal of this product as unsorted waste by its possessor will lead to an administrative penalty foreseen by national regulations. WARNING: EXPOSURE OF BATTERIES TO HIGH MECHANICAL STRESS, HIGH AMBIENT TEMPERATURES OR IMMERSION INTO FLUIDS High mechanical stress, high ambient temperatures or immersion into fluids can cause leakage, fire or explosions of the batteries. PRECAUTIONS: Protect the batteries from mechanical influences and high ambient temperatures. Do not drop or immerse batteries into fluids. WARNING: MECHANICAL INFLUENCES TO BATTERIES During the transport, shipping or disposal of batteries it is possible, to inappropriate mechanical for constitute a fire hazard. influences, PRECAUTIONS: Before shipping the product or disposing of it, discharge the batteries by running the product until they are flat. When transporting or shipping batteries, the person in charge of the product must ensure that the applicable national and international rules and regulations are observed. Before transportation or shipping, please contact your local passenger or freight transport company. NOTICE: Only IDS GeoRadar authorized technical service are entitled to repair this product. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 11/ 41 3 SAFETY DIRECTIONS Mod: MDM/011/M2 Rev 8 WARNING: Short circuit of battery terminals Risk of fire, electric shock, and damage. PRECAUTIONS: Do not open the battery housing. Keep away any metallic or wet objects from the battery terminals. WARNING: Short circuit of battery terminals If battery terminals are short-circuited e.g., by coming in contact with jewellery, keys, metallised paper or other metals, the battery can overheat and cause injury or fire, for example by storing or transporting in pockets. PRECAUTIONS: Make sure that the battery terminals do not come into contact with metallic objects. WARNING: Battery may get hot after prolonged use. Risk of burning injuries. PRECAUTIONS: Avoid touching the hot battery. Allow the battery to cool down before removing it. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 12/ 41 4 GENERAL DESCRIPTION 4 GENERAL DESCRIPTION The Chaser XR GPR system is designed to detect and locate underground features for a wide range of possible applications including, but not limited to Geology, Geotechnical, Environmental, Glaciers, Rivers, Archaeology, Forensic, buried structures It provides georeferenced in general. underground maps if a supported positioning system is used. 4.1 Delivery Contents The Georadar system Chaser XR includes 3 possible configurations: 1 is the basic configuration and 2 includes optional components to be purchased separately, namely:

1. Chaser XR Lite Pack (989791) 2. Chaser XR Drag kit (989754, optional), 3. Chaser XR Positioning Kit (986689, optional,). 4.1.1 Chaser XR Lite Pack (989791) The basic package includes:

a. Hardcase (989397) b. HPRC bag 2400 (989847) Mod: MDM/011/M2 Rev 8 c. Antenna Chaser XR with sledge and handles (987402) d. Wheel Encoder WHE50 (854803) IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 13/ 41 4 GENERAL DESCRIPTION Mod: MDM/011/M2 Rev 8 e. 2.5 meters LAN cable (987232, left image), and 0.50 meters Wheel 4.1.2 Chaser XR Drag Kit (989754, optional) Encoder cable (987233, right image). This optional package includes:

a. Chaser XR rugged Sledge for the antenna (987605) f. Chaser XR Pulling pole kit (987672). b. Wheel encoder mechanical coupling kit g. 2 Batteries GEB 364 (954519) and battery charger GKL311 single charger prof 3000 (799185). c. Wheel encoder WHE100 (854898) d. Wheel encoder cable IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 14/ 41 4 GENERAL DESCRIPTION Mod: MDM/011/M2 Rev 8 a b c d Fig. 1 Chaser XR Lite 4.1.3 Chaser XR Positioning Kit (986689, Optional) The optional positioning kit, includes:

a. Chaser XR GNSS Positioning support and bayonet adapter. Both the optional kits (the Drag kit and the Positioning kit) can be used only with the Chaser XR Lite Pack. 4.2 Basic System Composition The Chaser XR Lite Pack is the basic configuration in which the system may be purchased. Fig. 1 illustrates Chaser XR Lite after assembling and the following components are illustrated:

a) The telescopic drag pole with safety lace b) The LAN cable connecting the antenna and the PC (note: Chaser XR, may be deployed also WiFi, without any LAN cable) c) The Antenna with sledge and handles d) The WHE 50 encoder with encoder cable IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 15/ 41 4 GENERAL DESCRIPTION 4.3 Accessories 4.3.1 Chaser XR Drag Kit (optional) The Chaser XR can be upgraded by the drag kit allowing for the use of the system over more rough surface. This optional kit includes all the items described at 4.1 and the system, after its installation, is shown below (Fig. 2). Mod: MDM/011/M2 Rev 8 4.3.2 Chaser XR Positioning Kit (optional) A GNNS or a TPS can be paired to Chaser XR after installation of the positioning kit allowing for a GNSS antenna receiver or a 360 prism to be coupled to the top of the antenna case, after fixing it at its four corners by the 4 screws, provided with the optional kit. c a b a b Fig. 2 Chaser XR with Drag kit Fig. 3 Chaser XR including drag kit and positioning kit Fig. 2 illustrates Chaser XR after installation of the drag kit for rough terrain. The set up of these components makes the system differs with respect to the Chaser XR Lite version because of the following items:

Fig. 3 illustrates the Chaser XR in its full configuration also including the positioning kit. The difference with respect the Lite and the Drag Kit version relates to:

a) The WHE 100 encoder type b) The mechanical coupling kit c) The sledge for rough terrain a) GNSS antenna receiver (not included) b) Positioning kit IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 16/ 41 4 GENERAL DESCRIPTION 4.4 Battery Handling 4.4.1 Charging The temperature range for charging is between 0 C to +40 C/ +32 F to +104 F. For optimal charging, we recommend charging the batteries at a low ambient temperature of +10 C to +20 C/+50 F to +68 F if possible. 4.4.2 Operation/Discharging The batteries can be operated from 20 C to +50 C/4 F to +122 F. Lower operating temperatures reduce the capacity that can be drawn; higher operating temperatures reduce the service life of the battery. 4.4.3 Storage The following recommendations should be kept in mind with respect to storage of batteries:

Remove batteries from the product and the charger before storing. After storage recharge batteries before using. Protect batteries from damp and wetness. Wet or damp batteries must be dried before storing or use. The batteries can be stored from 20 C to +50 C/4 F to +122 F. 4.5 GNSS requirements Chaser XR can be used (paired) with a GNSS antenna or a TPS to position the GPR data in an absolute coordinates system and to receive real-time positional corrections while the system is moving and collecting georadar data. 4.5.1 How to connect Chaser XR to a GNSS Chaser XR can be linked to a GNSS which complies with the following characteristics:

Mod: MDM/011/M2 Rev 8 1. Dual frequency (L1+L2);

2. Positioning update minimum 5 Hz;

3. RTK: connection to a base station via radio link (UHF or GSM) or connection to a Continuously Operating Reference Station (CORS) via internet;

4. NMEA output in GGA format ONLY, and choose only one group of satellites

(GLONASS, Galileo) 5. Serial cable (RS232) is required, alternatively the GPS can be connected to the laptop via Bluetooth. Once configured, the GNSS does not need an application to be able to receive and transmit data. It can directly transmit the received data to a device (PC). In this case, the antenna is connected to the data logger via serial cable or Bluetooth. For the pairing procedure (and requirements) of the GNSS with uMap Controller PC, please refer to the users manual of the GNSS used. 4.5.2 How to connect Chaser XR to a TPS Chaser XR can be linked to a TPS which complies with the following characteristics:

1. Robotic Total Station 2. Motorized 3. Automatic Target Recognition (ATR) 4. Positioning update greater than 5 Hz 5. Range >1000 m (with prism) 6. Angular accuracy: <3 IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 17/ 41 5 HOW TO SET UP CHASER XR Mod: MDM/011/M2 Rev 8 7. Measure synchronization: angles measure and distance measure must be synchronized; maximum permitted latency must be less than 2 ms. 8. Wi-Fi/Bluetooth controller is required. 9. Serial port (RS-232) on the controller is required 10. Formatted output strings, pseudo NMEA output (Northing and Easting coordinates expressed in meters) is required. In this case, the remote controller must be connected to the Laptop through Bluetooth or a serial cable, to keep the Remote controller inside the vehicle during the acquisition phase. For the pairing procedure (and requirements) of the TPS with uMap Controller PC, please refer to the users manual of the TPS used. 5 HOW TO SET UP CHASER XR This section of the Users Manual provides the description on how to assemble Chaser XR in all its configurations. 5.1 How toset up Chaser XR Lite The assembly of the basic configuration of Chaser includes the following steps:

1. Open the Hard case and take off the Antenna. 2. Install the WHE 50 encoder in one of the female screws located at each of the 4 side of the antenna case indicated as the HH or the VV polarization. The position of the encoder is going to be 90 with respect to the acquisition mode (i.e.: encoder next to the HH label-

>acquisition mode VV, vice-versa, encoder next to the VV label-

>acquisition mode HH). 3. Plug the WHE50 encoder cable on top of the WHE 50 encoder, on one side, and on one of the (2) Wheel port beside the battery housing on top of the antenna case, on the opposite side of the cable. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 18/ 41 5 HOW TO SET UP CHASER XR Mod: MDM/011/M2 Rev 8 4. Install the anchor plate for the drag pole (its position varies depending if the system is used in HH or VV mode, and this is indicated onto the antenna case). 6. Plug the LAN cable on one side on the LAN port beside the battery housing on top of the antenna case, and to the LAN port of the PC on the opposite side of the cable (NOTE: this operation, is not necessary if the antenna is connected to the Controller via WiFi). 7. Release the screw on top of the battery compartment cover, open it, and insert the (2) batteries provided with the system. Then, close the cover. 5. Install the drag pole through the ball clamp. The VV or the HH label closer to it, shall indicate the acquisition mode. 8. Chaser XR, is now ready to be turned on using the 0/I button. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 19/ 41 5 HOW TO SET UP CHASER XR Mod: MDM/011/M2 Rev 8 5.2 How toset up Chaser XR Drag Kit (Optional) Starting from the configuration set up as per 5.1 above, the installation of the drag kit includes the following steps:

1. Remove the drag pole from its original position. 3. Remove (unscrew) the WHE50 encoder from the side of the antenna case. 2. Unplug the wheel encoder cable from the Wheel port on top of the antenna. 4. Place the sledge for rough terrain under the antenna and fix it through the screw to the antenna. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 20/ 41 5. Remove the anchor plate for the drag pole on top of the antenna. 5 HOW TO SET UP CHASER XR Mod: MDM/011/M2 Rev 8 8. Install the WHE 100 encoder in one of the 4 side of the antenna case indicated as the HH or the VV polarization. The position of the encoder is going to be opposite (180) with respect to the drag pole. 6. Install the anchor plate drag pole on the sledge frame. 9. Plug the WHE100 encoder cable on top of the WHE 100 encoder, on one side, and on one of the (2) Wheel port beside the battery housing on top of the antenna case, on the opposite side of the cable. 7. Install the anchor plat for the WHE100 encoder. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 21/ 41 6 HOW TO WORK ON SITE WITH CHASER XR Mod: MDM/011/M2 Rev 8 5.3 How toset up Chaser XR Positioning Kit (Optional) 6 HOW TO WORK ON SITE WITH CHASER XR The Positioning Kit can be used with both the Lite version as well as the version including the drag kit. Hence, the steps to set it up are:

1. Lay the positioning kit on the top of the antenna making sure that the holes at its four edges overlap with the female screw inserts at each of the four corners of the antenna and fix the (4) screws to secure the kit. 2. Couple the GNSS receiver antenna or the 360 prism either screwing directly or using the bayonet adapter provided with the kit. Chaser XR is a Georadar system that can be deployed on site in a wide variety of hardware and software configurations. Also, several positioning systems

(Encoder, Virtual Grid, GNSS, Robotic Total Station) can be associated to the Chaser XR HW and SW. The aim is to cover the largest possible applications and field conditions. 6.1 How to set up Chaser XR in HH or VV Polarization Besides the HW product configurations illustrated in 4.2 and 4.3 and their specific set up illustrated in 5.1, 5.2, and 5.3, Chaser XR can be deployed in 2 different orientation of the antenna, namely in HH (Horizontal, internal dipoles perpendicular with respect to the drag direction) or VV Polarization

(Vertical, internal dipoles parallel with respect to the drag direction). The HW set up in HH or VV polarization depends upon the relative installation of the Drag pole and the encoder wheel:

1. VV Polarization acquisition mode:

a. Drag pole attached next to the VV label on the antenna case. b. Wheel encoder fixed next to the HH label on the antenna case. 2. HH Polarization acquisition mode:

a. Drag pole attached next to the HH label on the antenna case. b. Wheel encoder fixed next to the VV label on the antenna case. 6.2 How to connect the field PC and the Chaser XR antenna The connection between the field PC (where the uMap data acquisition SW is installed) and the Chaser XR antenna can be fulfilled 1) via WiFi or 2) via LAN Cable. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 22/ 41 6 HOW TO WORK ON SITE WITH CHASER XR Mod: MDM/011/M2 Rev 8 Regardless the specific field configuration to be used to collect field data, the common steps to start up the system before commencing any data acquisition on site are:

1. Connecting Chaser XR antenna and field PC in Wi Fi Mode:

a. Open the battery compartment on top of the antenna case and insert the (2) batteries. Then close the same battery compartment. d. As the System led is solid green, the WiFi is ready. e. Turn on the field PC where the uMap software is installed

(note: please refer to the specific uMap users manual for details on installation. Also, firewall and antivirus must be OFF). The IP address of the WiFi port of the PC must be set to DHCP (Dynamic mode and NOT Static IP address). b. Press the O/I button beside the battery compartment to start up the antenna. c. 3 leds are present on top of the antenna case: 2 indicating the battery status, 1 the System status. As the system is turned on and the batteries are fully charged, the battery led shall be solid green and the system led shall have long-

paused blinking green-to-blue for three times, indicating that the internal WiFi module is starting up to generate its own local network. f. Click on the network icon on the lower right corner. g. Select the WiFi network generated by the Chaser antenna including the serial number of that specific antenna (e.g.:

Chaser XR 020-23-000542). Wait for connection. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 23/ 41 6 HOW TO WORK ON SITE WITH CHASER XR Mod: MDM/011/M2 Rev 8 h. Turn on uMap software, then press on the Radar diagnostic if needed, and the icon connection between the antenna and the PC is established.

, press update to the connection via LAN cable, but the WiFi module will be start up and usable in any case. d. Turn on the field PC where the uMap software is installed

(note: please refer to the specific uMap users manual for details on installation. Also, firewall and antivirus must be OFF). The IP address of the Ethernet port of the PC must be set to DHCP (Dynamic mode and NOT Static IP address). 2. Connecting Chaser XR antenna and field PC using LAN Cable:

a. Open the battery compartment on top of the antenna case and insert the (2) batteries. Then close the same battery compartment. e. Turn on uMap, press on the Radar diagnostic icon

, press update antenna and the PC is established.

, and the connection between the b. Connect the field PC and the Chaser XR antenna via the LAN cable provided with the system: on one side to the antenna LAN connector, on the opposite side to the LAN ort of the PC. c. Press the O/I button beside the battery compartment to start up the antenna. In this case, the green-to-blue blinking

(described in the previous paragraph) will be not present due Chaser XR, is now ready to be used on site for data acquisition. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 24/ 41 6 HOW TO WORK ON SITE WITH CHASER XR Mod: MDM/011/M2 Rev 8 6.3 How to collect Chaser XR data in Encoder mode Starting from a set up as per Fig. 1 (Chaser XR Lite) or Fig. 2 (Chaser XR Drag Kit), the minimum steps to be conducted to start gathering data are:

1. Start up the PC and launch the uMap acquisition software as per 6.2 and click on the Radar Status icon

. 2. Select the Antenna type Chaser XR from the drop-down menu in uMap. 5. Select the encoder type mounted on Chaser XR (WHE50 or WHE100). 3. Select the antenna frequency 6. Click on the positioning icon to switch to the Positioning view tab. 4. Select the Antenna orientation (HH or VV). 7. From the drop-down menu of the Positioning tab select the Encoder Mode. 8. Go back to the previous page by pressing the icon. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 25/ 41 6 HOW TO WORK ON SITE WITH CHASER XR Mod: MDM/011/M2 Rev 8 9. Press on the New Project icon to start a new project window. 10. In the Project Window, press the Play button to start the acquisition. 11. Press the Stop Acquisition button to close the swath acquisition. 12. Press the close current button to close the project. 13. Refer to uMap Software Users Manual for specific software tools. 6.4 How to collect Chaser XR data in GRID mode Starting from a set up as per Fig. 1 (Chaser XR Lite) or Fig. 2 (Chaser XR Drag Kit), the minimum steps to be conducted to start gathering data are:

1. Start up the PC and launch uMap the acquisition software as per 6.2 3. Select the Antenna orientation (HH or VV). 4. Select the encoder type mounted on Chaser XR (WHE50 or WHE100). 5. Click on the positioning icon to switch to the Positioning view tab. and click on the Radar Status icon

. 2. Select the Antenna type Chaser XR from the drop-down menu. 6. From the drop-down menu of the Positioning tab select the VGRID Mode. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 26/ 41 6 HOW TO WORK ON SITE WITH CHASER XR Mod: MDM/011/M2 Rev 8 7. Go back to the previous page by pressing the icon. 8. Press on the New Project icon to start a new project window. 9. In the Project Window, press the Play button to start the acquisition. 10. Press the Stop Acquisition button to close the swath acquisition. 11. Press the close current button to close the project. 12. Refer to uMap Software Users Manual for specific software tools. 6.5 How to collect Chaser XR data in GNSS mode Starting from a set up as per Fig. 1 (Chaser XR Lite) or Fig. 2 (Chaser XR Drag Kit), the minimum steps to be conducted to start gathering data are:

1. Start up the PC and launch uMap the acquisition software as per 6.2 and click on the Radar Status icon

. 2. Select the Antenna type Chaser XR configuration from the drop-

down menu. 3. Select the Antenna orientation (HH or VV). 4. Select the encoder type mounted on Chaser XR (WHE50 or WHE100). 5. Click on the positioning icon to switch to the Positioning view tab. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 27/ 41 6 HOW TO WORK ON SITE WITH CHASER XR Mod: MDM/011/M2 Rev 8 6. From the drop-down menu of the Positioning tab select the GNSS 6.6 How to collect Chaser XR data in TPS mode 12. Refer to uMap Software Users Manual for specific software tools. Mode. Starting from a set up as per Fig. 1 (Chaser XR Lite) or Fig. 2 (Chaser XR Drag Kit), the minimum steps to be conducted to start gathering data are:

1. Start up the PC and launch uMap the acquisition software as per 6.2 and click on the Radar Status icon

. 2. Select the Antenna type Chaser XR configuration from the drop-

down menu. 7. Go back to the previous page by pressing the icon. 8. Press on the New Project icon to start a new project window. 3. Select the Antenna orientation (HH or VV). 9. In the Project Window, press the Play button to start the acquisition. 10. Press the Stop Acquisition button to close the swath acquisition. 4. Select the encoder type mounted on Chaser XR (WHE50 or WHE100). 11. Press the close current button to close the project. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 28/ 41 6 HOW TO WORK ON SITE WITH CHASER XR Mod: MDM/011/M2 Rev 8 10. Press the Stop Acquisition button to close the swath acquisition. 11. Press the close current button to close the project. 5. Click on the positioning icon to switch to the Positioning view tab. 6. From the drop-down menu of the Positioning tab select the TPS Mode. 12. Refer to uMap Software Users Manual for specific software tools. 7. Go back to the previous page by pressing the icon. 8. Press on the New Project icon to start a new project window. 9. In the Project Window, press the Play button to start the acquisition. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 29/ 41 7 CARE AND TRANSPORT 7 CARE AND TRANSPORT 7.1 Cleaning Information Before cleaning any of the external parts of the apparatus, make sure that all cables and wires have been unplugged, including the power supply cable. If a damp cloth is used, make sure it is not wet, to avoid any damage to the electrical components of the equipment. Wait until the equipment is totally dry before reconnecting the cables. Mod: MDM/011/M2 Rev 8 CAUTION: DAMAGE TO ELECTRICAL COMPONENTS Consider only cleaning products appropriate for electronical components. PRECAUTION: Verify if the cleaning products are compliant with electronic devices. CAUTION: DAMAGE TO ELECTRICAL COMPONENTS Do not apply liquid directly to the electrical contacts of the various connectors. If a damp cloth is used while cleaning the system or part of it, make sure that this is not wet, to avoid any damage to the electrical components of the equipment If a specific spray is used to clean the PC monitor, make sure it is not flammable; in any case, do not spray it directly on the screen, instead, spray it onto the cleaning cloth. PRECAUTION: Before cleaning any of the external parts of the apparatus, make sure that all cables and wires have been unplugged, including the power supply cable. The Chaser XR should be cleaned periodically using a damp cloth. NOTICE: If the system is dirty, connectors and encoders may not work properly. Precautions:

After a field work, check the conditions of the system and clean it if necessary. Do not use solvents or abrasive detergents. CAUTION: DAMAGE TO ELECTRICAL COMPONENTS Flammable spray could damage the electronic devices, as controller laptop. PRECAUTION: Verify if the cleaning products are compliant with electronic devices. 7.2 Battery Removal Information Remove batteries from the product and the charger before storing. After storage recharge batteries before using. Protect batteries from damp and wetness. Wet or damp batteries must be dried before storing or use. A storage temperature range of 20 C to +50 C/4 F to +122 F in a dry IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 30/ 41 7 CARE AND TRANSPORT Mod: MDM/011/M2 Rev 8 environment is recommended to minimize self-discharging of the battery. At the recommended storage temperature range, batteries containing a 40% to 50% charge can be stored for up to one year. After this storage period the batteries must be recharged. As for the Laptop Batteries please, do refer to the PC manufacturer users manual. 7.3 Periodical Check The Operator should periodically check the status of the antenna sledge, shells, all cables, any rotating part, and any (potentially) consumable part. The system must not be used in case of any malfunctioning or broken part, as this may cause other parts to be damaged and/or malfunction consequently. NOTICE:

All the connectors on the antenna and the accessories, must be plugged at any time either by the corresponding cable plug, or by the connector cap, when not in use. This is to prevent dust or water ingress, that may damage the connector itself and its functionality. Precautions:

Verify the connectors status before running a survey. 7.4 Proper system use and Transport/shipping Always use the system as indicated in this manual, by following instructions. When not in use, the system should always be transported and/or shipped by using the flight case with which the system is delivered. Transporting and/or shipping the system outside this packaging or by using other shipping boxes may cause the system, or part of it, to be damaged. NOTICE: The Sledges should be periodically checked out to verify their status, and should be removed and replaced, when needed. Prior starting any survey, the status of the sledge should be verified for integrity. Precautions:

If the antenna shell is exposed, even partially, because of the sledge being consumed, the sledge must be replaced immediately. NOTICE: All the cables and connectors should be verified at each use of the system Precautions:

In case of any damage, remove and replace it. CAUTION: MECHANICAL DAMAGE OF THE SYSTEM Transporting and/or shipping the system outside its original packaging or by using other shipping boxes may cause the system, or part of it, to be damaged. PRECAUTION: The system should always be transported and/or shipped by using the flight case with which the system is delivered. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 31/ 41 7 CARE AND TRANSPORT Mod: MDM/011/M2 Rev 8 8 IDS GEORADAR SUPPORT 8.2 How to manage return for Service 8.1 myWorld myWorld platform of Leica Geosystems offers a wide range of services, information, and training material. With direct access to myWorld, the user can access all relevant services. The availability of services depends on the instrument model. myService mySupport SERVICE myProducts DESCRIPTION Add all IDS GeoRadar products that you and your company own and explore your world of Leica Geosystems: View detailed information on your products and update your products with the latest software and keep up to date with the latest documentation. View the current service status and full-service history of your products in IDS GeoRadar service centres including detailed information on the services performed on your system. Create new support requests for your products that will be answered by your local Support Team. View the complete history of your support requests and view detailed information on each request in case you want to refer to previous support requests. Welcome to the home of Leica Geosystems online learning!

There are numerous online courses available to all customers with products that have valid CCPs (Customer Care Packages). myTrustedServices Add your subscriptions and manage users for Leica Geosystems Trusted Services, the secure software services, that assist you to optimise your workflow and increase your efficiency. HxGN SmartNet is the GNSS correction service built on the worlds largest reference station network, enabling GNSS-

capable devices to quickly determine precise positions in the range of one to two centimetre accuracy. The service is provided 24/7 by a highly-available infrastructure and professional support team with more than 10 years of experience reliably delivering the service. Downloads of software, manuals, tools, training material and news for IDS GeoRadar products. myDownloads mySmartNet myLearning On occasions, your GPR may need to be returned to factory for repairs. These events, depending on circumstances, may be handled under maintenance or warranty conditions. IDS GeoRadar, implements an internal ticket system to handle the repair of its Products worldwide. In this respect, for the global IDS Customer Support to be able to troubleshoot in case of need, it is necessary identifying the GPR system first hence, it is mandatory providing information including Serial number and Product Number of the system or part of it that need repair. This information may be found on a label placed on top of the system (e.g.:

inside the battery housing, on top of the antenna, on the side of the rudder, on top of the SCU, etc.). An example of this label is illustrated in Fig. 4. Fig. 4 Example of an IDS GPR system label In any event, the workflow to follow up on a support request is:

1. Contact, by using the local representative of IDS Customer Support, or enter a support case into the mySupport page of myWorld, Indicating the following:

local Support mailing list, your a. Type of System or part of it (defined by Product Number or Article number, that is PN 859224 in Fig. 4) b. Serial Number (SN 020-21-000333, in Fig. 4) c. Type of issue IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 32/ 41 7 CARE AND TRANSPORT Mod: MDM/011/M2 Rev 8 2. The local Representative of IDS Customer Support or the Central IDS Customer Support shall follow up on the case by a first level, remote troubleshooting to assess the system and the possible issue. 3. If a further, direct assessment of the system is necessary, the system shall be returned for analysis. Based on this, a repair under warranty or maintenance conditions, may be carried out. Depending on cases and the type of possible repair, return may be towards the local Representative of IDS or to the main factory. 4. Prior return of the goods, wait for the IDS logistic office to provide a reference number for the return case and shipping instructions. 5. As the system reaches IDS repair premises, this is analyzed to find the root cause of the issue, and repaired ONLY after signed approval of the quotation, in case where the warranty does not apply. The status of the repair may be checked onto the mySupport page of myWorld. 6. At the end of the repair, the system is shipped back to the shipping address indicated at the beginning of the procedure, and this is conducted based on contractual agreements. NOTICE: The above, is meant solely as a broad indication of the workflow for the return of a system for repair. Precautions:

Please, refer to the Contractual Terms and Conditions for more detailed information. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 33/ 41 APPENDIX A DISCLAIMER Mod: MDM/011/M2 Rev 8 APPENDIX A DISCLAIMER 1. General i. ii. iii. The present Disclaimer applies to all products designed, produced and distributed by IDS GeoRadar S.r.l., its Subsidiaries, Affiliated and authorized Distributors (the Products). IDS GeoRadar S.r.l. reserves full ownership and intellectual property rights of any Information contained in this Disclaimer including Trade Marks and Graphics. No part of this Disclaimer may be used or reproduced in any forms without the prior written agreement of IDS GeoRadar S.r.l. In the event that any provision of this Disclaimer may be invalid, unlawful or incapable of being enforced by a rule of law, all other provisions shall, nonetheless, remain in full force and effect. Failure to either enforce or exercise any right, privilege, or legal remedy at any time, any provision contained in this Disclaimer, shall not be deemed a waiver of such provisions or right, remedy, or privilege. This Disclaimer shall be interpreted, governed, construed and enforced in accordance with the laws of Italy. User/Buyer hereby consents to the exclusive jurisdiction of Pisa. 2. Initial Precautions for Setting-up and Use of the Products. i. ii. The User/Buyer, for setting-up and using the Products, shall consult the official documentation provided by IDS GeoRadar S.r.l. for the Products (Reference Documentation) and carefully ascertain the compliance with national laws and requirements, which may limit or even forbid their use. For Products which shall operate by circulation in Public Areas/Roads, with or without moving traffic, Buyer/User shall verify the approval of local authority and/or sites owner according to their specific procedures. IDS GeoRadar S.r.l. shall not be liable for any direct, indirect, special, incidental or consequential damages or injuries, including without limitation, lost revenues or lost profits, resulting by un-authorized use of the Products Areas/Roads. in Public iii. Buyer/User further warrants:

that these Products are not being used, in the design, development, production or use of chemical, biological, nuclear ballistic weapons. Buyer/ User will defend, indemnify and hold IDS GeoRadar S.r.l. harmless against any liability (including attorneys fees) for non-compliance with the terms of this article. That, if IDS GeoRadar S.r.l. requires that Buyer/User shall carry out a training with reference to some Product categories, no operation or use of the Products shall be started before its designated Operator/s has got the User Certificate, as defined by IDS GeoRadar S.r.l. specific procedure which the Buyer confirms to know and accept. iv. v. For Products which include specific Operational software with automatic data processing and analysis Tools, e.g. the IBIS Products and Hydra Products, User shall be aware that the results provided by these Tools may be not error free. User that completely relies on the outcomes provided by these Tools only, does it at his own risk. In no event IDS GeoRadar S.r.l. shall be liable for special, direct, indirect, incidental, exemplary, punitive or consequential damages including, but not limited to, loss of profits or revenue, caused by the use of the Products, either separately or in combination with other products or relied upon the results provided by the above Tools. 3. Disclaimer for the Use of the Products. i. The User shall follow the instructions provided by IDS GeoRadar S.r.l. in its official Reference Documentation for the Product, in particular the Users Technical Manual which contains all the specific steps and recommendations for a correct setting-up and use of the Product. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 34/ 41 APPENDIX A DISCLAIMER Mod: MDM/011/M2 Rev 8 earthquake, unexpected events. flooding or other natural disasters or j. Use or storage of the Products outside the limits of the Operational Temperature Range specified by IDS GeoRadar S.r.l. ii. In no event IDS GeoRadar S.r.l. shall be liable for special, direct, indirect, incidental, exemplary, punitive or consequential damages including, but not limited to, loss of profits or revenue, caused by the missed or incomplete observance of the instructions and prescriptions for the use of the Products, either separately or in combination with other products, including but not limited to the following main aspects:

a. Use of IDS GeoRadar S.r.l. Products outside its limitation of use, without proper and adequate scientific/technical knowledge or without specific training. b. Use of results/outcomes of the measurements performed by the Product aimed to safety aspects without using adequate control procedures and assessment by skilled personnel. c. Opening of the Equipment (for HW Products) without express written authorization of IDS GeoRadar S.r.l.;

d. Unauthorized changes and additions to the Products. e. Use of the Products connected to suspected non-working

(mainly PC) having in compliance with the required IDS GeoRadar S.r.l. not expressly equipment or with equipment characteristics not specifications of authorized by IDS GeoRadar S.r.l.;

f. Poor or faulty operation of the electrical and telecommunication networks not directly managed by IDS GeoRadar S.r.l. or its delegates. g. Poor or faulty operation Software/Hardware of the third parties connected with IDS GeoRadar S.r.l. Equipment. h. Poor or faulty operation of the Products due to Software Virus which infected the Products after their delivery. i. Use of the Products which have encountered suspected manumissions, accidents, electrostatic shocks, flashes, fire, IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 35/ 41 APPENDIX B TECHNICAL SPECIFICATIONS Mod: MDM/011/M2 Rev 8 APPENDIX B TECHNICAL SPECIFICATIONS SOFTWARE SPECIFICATIONS PARAMETER CONFIGURATION Chaser XR 200 Deep Chaser XR 200-900 Number of channels Maximum time-range 1 512ns Max number of samples 2048 Maximum radar speed ca 50 km/h (31 mph) 2 128ns Polarization HH and VV (depending on acquisition mode) Power consumption Stand-by: 12 W; Acquisition: 16W Max Operating Time 8h (acquisition), with two batteries. Extended, by hot swap capability Antenna Size 430 x 430 x 184 mm System Size (with Drag Kit

+ Positioning kit) 690 x 496 x 324 mm Antenna Weight (without batteries) 5.5Kg Environmental IP65 Certification EC, FCC, IC, UKCA Recommended Laptop Panasonic FZ-G2 Positioning Internal PPS; Encoder; External GPS and TPS uMap Acquisition Software IQMaps Processing Software Automatic calibration for an easy and quick start-up Visualization and storage of radar data Real-time visualization of radar tomography

(time-slices). Connection with NMEA positioning. Device multi-

language. Supports both Metric and Imperial units Advanced 3D processing software with a direct export link to AutoCAD Tab. 1 Radar Sensor Technical Specifications Exposure to Radio Frequency (RF) Signals:

For this the minimum distance between the user and any radiating elements is about 200 mm. SAR evaluation is not required because the output power value is less than exemption limit at such separation distance. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 36/ 41 APPENDIX B TECHNICAL SPECIFICATIONS Mod: MDM/011/M2 Rev 8 APPENDIX C CONFORMITY TO EUROPEAN and UK REGULATIONS We, IDS Georadar s.r.l. via A. Righi, 6, 6 A, 8, 56121 PISA, ITALY We, IDS Georadar s.r.l. via A. Righi, 6, 6 A, 8, 56121 PISA, ITALY declare under our sole responsibility that the product:

declare under our sole responsibility that the product:

Ground Penetrating Radar (GPR) Model No(s): CHASERXR Ground Penetrating Radar (GPR) Model No(s): CHASERXR To which this declaration relates, is in conformity with the essential requirements of To which this declaration relates is in conformity with the relevant legislation of United Kingdom:

2014/53/EU Directive (RED) UK SI 2017 No. 1206 The Radio Equipment Regulation 2017 The product(s) has been tested according to the following standards or technical specifications:

The following BSI standards and technical specifications have been applied:

standard(s) or other normative document(s):

Essential requirements Essential requirements for the protection of the health and safety of people, pets and goods, Article 3.1a) Essential requirements on electromagnetic compatibility levels, Article 3.1b) Essential requirements for the effective use of radio spectrum, Article 3.2 Standard

- Assessment for conformity to Art. 3.1a

(Safety)

- Assessment for conformity to Art. 3.1a

(Health) ETSI EN 301 489-33 V2.2.1 (2019-04) ETSI EN 301 489-1 V2.2.3 (2019-11) ETSI EN 302 066 V2.2.1 (2020-06) ETSI TS 103 361 V1.1.1(2016-03) Essential requirements Radio Testing (UK Part 2 Chapter 1(6)(2)) EMC testing (UK Part 2 Chapter 1(6)(1)(b) Safety testing (UK Part 2 Chapter 1(6)(1)(a)) Standard ETSI EN 302 066 V2.2.1 (2020-06) ETSI TS 103 361 V1.1.1(2016-03) ETSI EN 301 489-33 V2.2.1 (2019-04) ETSI EN 301 489-1 V2.2.3 (2019-11)

- Assessment for conformity to UK Part 2 Chapter 1(6)(1)(a) (Safety)

- Assessment for conformity to UK Part 2 Chapter 1(6)(1)(a) (Health) IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 37/ 41 APPENDIX B TECHNICAL SPECIFICATIONS Mod: MDM/011/M2 Rev 8 APPENDIX D IMPORTANT NOTE FOR US CUSTOMERS FCC ID: UFW-CHASERXR This device complies with part 15 of the FCC Rules:

Operation is subject to the following conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Operation of this device is restricted to law enforcement, fire and rescue officials, scientific research institutes, commercial mining companies, and construction companies. Operation by any other party is a violation of 47 U.S.C. 301 and could subject the operator to serious legal penalties. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to in a residential provide reasonable protection against harmful installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. interference Coordination Requirements.

(a) UWB imaging systems require coordination through the FCC before the equipment may be used. The operator shall comply with any constraints on equipment usage resulting from this coordination.

(b) The users of UWB imaging devices shall supply detailed operational areas to the FCC Office of Engineering and Technology who shall coordinate this information with the Federal Government through the National Telecommunications and Information Administration. The information provided by the UWB operator shall include the name, address and other pertinent contact information of the user, the desired geographical area of operation, and the FCC ID number and other nomenclature of the UWB device. This material shall be submitted to the following address:

Frequency Coordination Branch., OET Federal Communications Commission 445 12th Street, SW Washington, D.C. 20554 ATTN: UWB Coordination

(c) The manufacturers, or their authorized sales agents, must inform purchasers and users of their systems of the requirement to undertake detailed coordination of operational areas with the FCC prior to the equipment being operated.

(d) Users of authorized, coordinated UWB systems may transfer them to other qualified users and to different locations upon coordination of change of ownership or location to the FCC and coordination with existing authorized operations.

(e) The NTIA/FCC coordination report shall include any needed constraints that apply to day-to-day operations. Such constraints could specify prohibited areas of operations or areas located near authorized radio stations for which additional coordination is required before operation of the UWB equipment. If additional local coordination is required, a local coordination contact will be provided.

(f) The coordination of routine UWB operations shall not take longer than 15 business days from the receipt of the coordination request by NTIA. Special temporary operations may be handled with an expedited turn-around time when circumstances warrant. The operation of UWB systems in emergency situations involving the safety of life or property may occur without coordination provided a IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 38/ 41 APPENDIX E IMPORTANT NOTES FOR CANADIAN CUSTOMERS Mod: MDM/011/M2 Rev 8 Cet quipement goradar doit tre utilis que par des organismes d'application de la loi, des instituts de recherche scientifique, des socits minires commerciales, des entreprises de construction et de secours d'urgence ou les organisations de lutte contre les incendies. Cet appareil contient des metteurs/rcepteurs exempts de licence qui sont conformes aux RSS(s) exempts de licence dInnovation, Sciences et Dveloppement conomique Canada. Lexploitation est soumise aux deux conditions suivantes :

1. Cet appareil ne peut pas causer dinterfrence. 2. Cet appareil doit accepter toute interfrence, y compris les interfrences qui peuvent provoquer un fonctionnement indsirable de lappareil. notification procedure, similar to that contained in CFR47 Section 2.405(a)-(e), is followed by the UWB equipment user. Notice This device devices may not be employed for the operation of toys. Operation onboard an aircraft, a ship or a satellite is prohibited. APPENDIX E IMPORTANT NOTES FOR CANADIAN CUSTOMERS IMPORTANT NOTE FOR THE CANADIAN CUSTOMERS IC Certification Number: 8991A-CHASERXR This device complies with the requirements of IC Standard RSS-220 This Ground Penetrating Radar Device shall be operated only when in contact with or within 1 m of the ground. This Ground Penetrating Radar Device shall be operated only by law enforcement agencies, scientific research institutes, commercial mining companies, construction companies, and emergency rescue or firefighting organizations. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. NOTE IMPORTANTE POUR LES UTILISATEURS CANADIENS Numro de certification : 8991A-CHASERXR Cet appareil est conforme aux exigences de la norme RSS IC-220 Cet quipement goradar doit tre utilis que lorsquil est en contact ou moins de 1 mtre du sol. IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 39/ 41 APPENDIX F TROUBLESHOOTING APPENDIX F TROUBLESHOOTING Mod: MDM/011/M2 Rev 8 LED Status Error Troubleshooting SYSTEM Blue No connection between Chaser XR system and Controller

- Verify connection of the LAN cable between Chaser XR and Controller Red Internal hardware error

- Verify that the Network Adapter is in DHCP mode (IP address not static) Stop the acquisition Try to update configuration in uMap Software If error is still present, reset the Chaser XR system by power off and on the GPR antenna If the LED is still in error mode, contact Customer Support

BATTERY Red Low battery percentage

- Replace the battery IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 40/ 41 Mod: MDM/011/M2 Rev 8 APPENDIX G CONTACTS APPENDIX G CONTACTS The IDS GeoRadar Support team is available to answer any question about:

general enquiries request of advertising material technical issues As well as listening to your suggestions too. Please, feel free to contact us at:

IDS GeoRadar S.r.l. via Augusto Righi, 6/6A/8 Ospedaletto - 56121 Pisa, Italy

(39) 050 8934 122

(GEO BU Customer Technical Support) support.geo@idsgeoradar.com IDS GeoRadar Srl MNG/2023/007 Rev. 1.0 41/ 41

EUT: Chaser XR Model: CHASERXR FCC ID: UFW-CHASERXR IC:8991A-CHASERXR Report Number: 0048-230710-01-FCC-IC Section 5. ID Labeling IDS GeoRadar Product Name: CHASER XR Model No.: CHASERXR FCC ID: UFW-CHASERXR IC:8991A-CHASERXR Contains FCC ID: Z9W-RMB IC ID: 11468A-RMB ID Label (draft)

*The statement can also be shown in its User Manual:

This device complies with Part 15, Subpart F of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference; (2) This device must accept any interference received, including interference that may cause undesired operation. This device complies with the requirements of IC Standard RSS-220. ID Label FCC/IC ID Label Location Page 49 Advanced Compliance Laboratory, Inc. 210 Cougar Court, Hillsborough, NJ 08844, Tel: (908) 927 9288

FCC AND IC AUTHORIZATION LETTER

(FCC ID: UFW-CHASERXR IC: 8991A-CHASERXR) PRODUCT NAME: CHASER XR IDS GeoRadar Headquarters Via A. Righi, 6, 6A, 8 56121 Pisa (PI) Italy Tel. +39.050 098 300 Fax

+39.050.7912.130 info@idsgeoradar.com www.idsgeoradar.com Date: 2023, July, the 24th To whom it may concern:

We, the undersigned, hereby authorize Wei Li at Advanced Compliance Lab, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Advanced Compliance Lab on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing Advanced Compliance as our agent, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which certification has been c) granted;

do not use our product certification in such a manner as to bring the Certification Division into d) disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

IDS GeoRadar s.r.l. - Codice Fiscale 02216580502 VAT n IT 02216580502 - RAEE N IT16060000009358 Legal office Via Carducci n. 32, 20123 Milano (MI) Italy Registered at the Milano Chamber of Commerce, R.E.A. 2115412 - Pec idsgeoradar@pec.it Share capital Euro 20.000 fully paid A company with a sole shareholder, subject to the coordination and control of Hexagon Geosystems Services S.p.a. Cornegliano Laudense (LO) Via Codognino 10, 26854, Cod. Fiscale 09430450966 use certification only to indicate the products are certified as being in conformity with specified f) standards;

g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, h) brochures or advertising, complies with the requirements of the Certification Division;

i) keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or j) services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Regards, Firma recuperabile X Firmato da: S-1-12-1-740968272-1287637154-3942116779-884963285/565b3418-515d-48d5-8035-6d603f4e8086 Alessandro Simi Director R&D IDS GeoRadar s.r.l. - Codice Fiscale 02216580502 VAT n IT 02216580502 - RAEE N IT16060000009358 Legal office Via Carducci n. 32, 20123 Milano (MI) Italy Registered at the Milano Chamber of Commerce, R.E.A. 2115412 - Pec idsgeoradar@pec.it Share capital Euro 20.000 fully paid A company with a sole shareholder, subject to the coordination and control of Hexagon Geosystems Services S.p.a. Cornegliano Laudense (LO) Via Codognino 10, 26854, Cod. Fiscale 09430450966

IDS GeoRadar

[= , CFR 47 2.911 (d)(7) Agent Designation Attestation Date: 08-22-2023 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Ref: Attestation Statements Part 2.911(d)(7) Filing FCC Grantee Code: UFW Applicant FRN: 0015281504 IDS GeoRadar s.r.l. (the applicant) certifies that, as of the date of the filing of the application, Leica Geosystems Inc. is our designated U.S. agent for service of Process for the above referenced FCC ID. IDS GeoRadar s.r.|. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Leica Geosystems Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of Process for the above referenced FCC ID, Designated U.S. Agent Information:

Name: Leica Geosystems Inc. U.S. Agent FRN: 0022965586 Address: 5051 Peachtree Corners Circle, Suite 250, Norcross, GA, 30092, USA Contact Person: Henry Munoz Tel.: +1 303 232 3047 Email: henry. munoz@idsgeoradar.com Sincerely, IDS GeoRadar s.r.. Leica Geosystems Inc. Alessandro Simi Henry Munoz 1DS GeoRadar s.r1. Headquarters Via A Righi6, 6A. 8 56121 Pisa (Pitaly La HXacon 28 Milano (Mi) italy a _ ae IDS GeoRadar w f IDS GeoRadar s.r), Head arters Via A Righi, 6, 6A, 8 56121 Pisa (Pilitaly Tel (098 9300 Fax +39.050,7012.

(a Hexagon info@idsgeoradar.com 2216580502 - VAT n

CFR 47 2.911 (d)(5) Attestation Date: 08-22-2023 FCC ID: UFW-CHASERXR To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA 1. IDS GeoRadar s.r.l. (the applicant) certifies that the equipment for which authorization is sought is not a covered equipment, prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. 2. IDS GeoRadar s.r.l (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment and is not an affiliate or subsidiary of an entity identified on the Covered List. Sincerely yours, Invalid signature X Signed by: S-1-12-1-740968272-1287637154-3942116779-884963285/565b3418-515d-48d5-8035-6d603f4e8086/

Name:

Alessandro Simi Job Title:

R&D Director Company Name: IDS GeoRadar s.r.l. IDS GeoRadar s.r.l. Headquarters Via A. Righi, 6, 6A, 8 56121 Pisa (PI)Italy Tel. +39. 050 098 9300 Fax +39.050.7912.130 info@idsgeoradar.com www.idsgeoradar.com Codice Fiscale 02216580502 VAT n IT 02216580502 - RAEE N IT16060000009358 Legal office Via Carducci n. 32, 20123 Milano (MI) Italy Registered at the Milano Chamber of Commerce, R.E.A. 2115412 - Pec idsgeoradar@pec.it Share capital Euro 20.000 fully paid A company with a sole shareholder, subject to the coordination and control of Hexagon Geosystems Services S.p.a.

REQUEST FOR CONFIDENTIALITY Date: 24 July 2023 Subject: Confidentiality Request for: _UFW-CHASERXR IDS GeoRadar Headquarters Via A. Righi, 6, 6A, 8 56121 Pisa (PI) Italy Tel. +39.050.0989300 Fax +39.050.7912.130 info@idsgeoradar.com www.idsgeoradar.com Pursuant to FCC 47 CRF 0.457(d), the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term X Permanent Permanent Permanent Permanent Permanent Permanent Permanent Exhibit Block Diagrams External Photos Internal Photos Operation Description/Theory of Operation Parts List & Placement/BOM Tune-Up Procedure Schematics Test Setup Photos Users Manual Note: these materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. The devices pictured in the documents CHASERXR-internal pictures.pdf are sealed units that cannot be opened after manufacturing without destroying the contents. Specifically in order to view inside the product to which this request refers, one would have to carry out the following steps:

Inside the unit, electromagnetic absorbers cannot be removed without damage and will have to be 1. Use a special key to remove the screws securing the cover. This special key is not available to the general public. Moreover, these screws have to be removed in a specific order not to cause irreparable damages. The information on the removal order is available to IDS GeoRadar and to authorized repair centers only. 2. replaced with new ones when re-assembling. This material is custom built and not available to the public or to a competitor. 3. De-solder the transmitter AND the receiver from the antenna flares to initiate access to certain electronics of the antenna. Then carefully disconnect and withdraw the assemblies from the shield /construct assembly. When these steps are done improperly the electronics can be severely damaged. IDS GeoRadar has never released public instructions on how to disassemble its units and does not answer questions on how to do so. This information is kept internal to the company. If a unit arrives at the company's repair facility showing evidence of such tampering, the company does not repair it, but charges the customer for a new unit plus freight costs. The Commission's posting of the photographs as well as of the schematics and components list, would allow a competitor to bypass this difficult and expensive disassembly. From the photographs, a competitor can also estimate:

IDS GeoRadar s.r.l. - Codice Fiscale 02216580502 VAT n IT 02216580502 - RAEE N IT16060000009358 Legal office Via Carducci n. 32, 20123 Milano (MI) Italy Registered at the Milano Chamber of Commerce, R.E.A. 2115412 - Pec idsgeoradar@pec.it Share capital Euro 20.000 fully paid A company with a sole shareholder, subject to the coordination and control of Hexagon Geosystems Services S.p.a. Cornegliano Laudense (LO) Via Codognino 10, 26854, Cod. Fiscale 09430450966 1. the costs of manufacturing the printed circuit boards and mechanical housing;

2. the man-hours required to assemble the device;

3. any compatibility problems the manufacturer will have in designing new systems; and 4. the age of the electronic design (which gives valuable competitive information on upgrade and R&D efforts). Access to interior photographs would almost permit a competitor to conduct a complete reverse engineering, to the point of producing a schematic. We are also noting that The Commission has previously granted confidentiality under similar conditions to several applications concerning GPR devices: e.g. QF7350HS QF742600 QF7MINIXT QLA450MHZHDR QLA160MHZHDR QLA750MHZHDR QLA80MHZHDR We are also reminding that the unit will not be made available for sale to the general public. Marketing will be limited to law enforcement, fire fighting, emergency rescue, scientific research institutions, commercial mining companies, construction companies, surveying companies and those parties providing services to these entities pursuant to CFR 47, Part 15, Subpart F, 15.509 Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 90 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. Sincerely, Firma recuperabile X By:

Firmato da: S-1-12-1-740968272-1287637154-3942116779-884963285/565b3418-515d-48d5-8035-6d603f4e8086 R&D Manager_

(Signature/Title) Alessandro Simi

(Print name) IDS GeoRadar s.r.l. - Codice Fiscale 02216580502 VAT n IT 02216580502 - RAEE N IT16060000009358 Legal office Via Carducci n. 32, 20123 Milano (MI) Italy Registered at the Milano Chamber of Commerce, R.E.A. 2115412 - Pec idsgeoradar@pec.it Share capital Euro 20.000 fully paid A company with a sole shareholder, subject to the coordination and control of Hexagon Geosystems Services S.p.a. Cornegliano Laudense (LO) Via Codognino 10, 26854, Cod. Fiscale 09430450966