FCC ID: SE6B001 ACCESS POINT 915MHz (US) / LAN

User Guide CUG00029-EN-A01 USER GUIDE Access point AP2-LAN This device complies with FCC radiation exposure limits set forth for general population. This device must not be co-located or operating in conjunction with any other antenna or transmitter. User Guide CUG00029-EN-A01 SUMMARY 1 2 Introduction .................................................................................................................................................................... 3 Connection to the internal serial access point using the LAN network .......................................................................... 3 3 Warning to users in the United States ............................................................................................................................ 6 4 Warning to users in the Canada ..................................................................................................................................... 6 5 Revision of the document ............................................................................................................................................... 7 IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC France : +33 2 98 09 03 30 Customer Service: +33 2 98 09 03 32 / sav@ijinus.com Access point AP2-LAN 1 Introduction User Guide CUG00029-EN-A01 This device is a radio access point used to transfers data into remote sensors nearby via a LAN connection. A serial to ethernet interface is embedded in the device. We provide to our clients a command list or a software library, to drive the access point. They are able to manage it with their own software and paired the sensors

(temperature recorders, loggers, sensors). 2 Connection to the internal serial access point using the LAN network The AP2-LAN radio access point contains an Ijinus radio board (T2004) and a Moxa NE-4120s RS-232 Ethernet interface. The moxa board allows RS232 communication through a LAN Network. A COM port will be created and will be used for serial link operations.

- Install the Moxa Network Enabler Administrator software It can be downloaded here :

https://www.moxa.com/Moxa/media/PDIM/S100000224/moxa-ne-4100-series-network-enabler-

administrator-utility-v2.11.zip This tool allows the discovery of the NE4120s on the network and its configuration.

- Set the NE-4200s has shown below :

Serial setting: 115200bps N-8-1 No flow control IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC France : +33 2 98 09 03 30 Customer Service: +33 2 98 09 03 32 / sav@ijinus.com 3 Access point AP2-LAN Operation mode :

RealCOM Mode User Guide CUG00029-EN-A01

- Install Moxa driver manager It can be downloaded here :

https://www.moxa.com/Moxa/media/PDIM/S100000224/moxa-windows-driver-manager-driver-v3.0.zip This tool allows the creation of a COM Port on your desktop. This COM Port will be used to connect the T2004 with Hyperterminal (or equivalent). The port is added using a search the Add button and then the search utility :

IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC France : +33 2 98 09 03 30 Customer Service: +33 2 98 09 03 32 / sav@ijinus.com 4 Access point AP2-LAN Set a number to the COM Port and configure it :

User Guide CUG00029-EN-A01 The created COM port has been added in Windows peripheral manager:

IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC France : +33 2 98 09 03 30 Customer Service: +33 2 98 09 03 32 / sav@ijinus.com 5 Access point AP2-LAN 3 Warning to users in the United States User Guide CUG00029-EN-A01 Caution: the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

"NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. This device complies with FCC RF radiation exposure limits set forth for general population. This device must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. 4 Warning to users in the Canada This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This device complies with Industry Canada RF radiation exposure limits set forth for general population

(uncontrolled exposure). This device must be installed to provide a separation distance of at least 20cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. This device has been designed to operate with its own internal antenna and having a maximum gain of 0dBi. IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC France : +33 2 98 09 03 30 Customer Service: +33 2 98 09 03 32 / sav@ijinus.com 6 Access point AP2-LAN User Guide CUG00029-EN-A01 5 Revision of the document Date Revision Writer(s) Modifications 11/21/2019 2A01 Creation of the document and translation A. Le Gac D. MAHE IJINUS - 25 ZA de Kervidanou 3, 29300 MELLAC France : +33 2 98 09 03 30 Customer Service: +33 2 98 09 03 32 / sav@ijinus.com 7

Technical Documentation Label Location FCC ID SE6B001 Publication History Version 01 Date November 26, 2019 Modification description Creation of the document Technical Documentation Label Location FCC Label location for AP2-LAN:

AP2-LAN:

Label Location View Version : 01 Page 2/2

Technical Documentation Label FCC ID SE6B001 Publication History Version 01 Date November 26, 2019 Modification description Creation of the document Technical Documentation Label AP2-LAN FCC Label size:

Size = 51x29 mm Label:

Photo of product with label:

Version : 01 Page 2/2

NINUS ZA Kervidanou 3 25 Rue Albert Schweitzer 29300 Mellac To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046-1609 Date: November 25", 2019 To Whom It May Concern:

Ladies and Gentlemen:

We, the undersigned, hereby authorize LCIE Bureau Veritas to act on our behalf in all matters relating to application for equipment authorization FCC ID: SE6B001 including the signing of all documents related to this matter. Any and all acts carried out by LCIE Bureau Veritas on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits including FCC benefits, pursuant to Section 5301 of Anti-drug Abuse Act of 1988, 21 U.S.C 862. Sincerely, Olivier LE STRAT Chief Executive Officer Mail: olivier.lestrat@ijinus.fr Tel: +33(0) 2 98 09 03 30 Ijinus ZA Kervidanou 3, 25 rue A. Schweitzer 29300 MELLAC Tl: +33 2 98 09 03 30 | Fax: +33 2 98 96 29 01 | Web: http://www. ijinus.cm TVA intracommunautaire: FRO1 449152644 SIRET: 449152644 00026 Code APE: 2651B SAS au capital de 1 000 000 1/1

@A WINUS INUS ZA Kervidanou 3 25 Rue Albert Schweitzer 29300 Mellac To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046-1609 Bureau Veritas Consumer Products Services Inc One Distribution Center Circle, #1 Littleton, MA 01460 Re: Confidentiality Request Ladies and Gentlemen:

This letter is to comply with 47 CFR 0.457(d)(2) and 0.459 pertaining to confidential material. IJINUS requests that the following documents regarding this submission for FCC ID SE6B001 be kept confidential:

f Schematics Block Diagram Circuit/Technical Description

. Part List PWNE The material above contains technical data, which would customarily be guarded from competitors. Sincerely,

Olivier LE STRAT Chief Executive Officer Mail: olivier.lestrat@ijinus.fr Tel: +33(0) 2 98 09 03 30 Mellac, November 18", 2019 Ijinus ZA Kervidanou 3, 25 rue A. Schweitzer 29300 MELLAC Tl: +33 2 98 09 03 30 | Fax: +33 2 98 96 29 01 | Web: http://www.ijinus.cm TVA intracommunautaire: FRO1 449152644 SIRET: 449152644 00026 Code APE: 2651B SAS au capital de 1 000 000 1/1