FCC ID: FHO-LED2103G5 Self-ballasted LED lamp

TRDFRI English Franais Espaol 4 8 12 English 4 ADD LIGHT SOURCES TO YOUR STEERING DEVICE:

Before you can use your light source youll need to pair it with a steering device. To add more light sources, just repeat the steps below:

Up to 10 light sources can be paired with 1 steering device. Make sure to pair them one at a time. If the light sources are close to each other, disconnect those that have already been paired from the main power switch. 1. Make sure that your light source is installed and the main power switch is turned on. 2. Hold the steering device close to the light source you want to add (no more than 5 cm away). 3. Press and hold the pairing button for at least 10 seconds. A red light will shine steadily on the steering device. Your light source will begin to dim and finally flash one time to indicate that it has been successfully paired. CAUTION:

DO NOT USE WITH STANDARD DIMMERS. Only use the control provided with or specified by these instructions to control this bulb. This bulb will not operate properly when connected to a standard (incandescent) dimmer or dimming control. Only controllable by IKEA Smart lighting products. The colour temperature can be switched between 2200K (warm glow), 2700K (warm white) and 4000K (cool white). RESET YOUR DEVICE Toggle the main switch 6 times. TECHNICAL DATA:

Operating frequency: 2405 2480 MHz Output power: 10 dBm 5 This device complies with Part 15 of the FCC Rules/Innovation Science and Economic Development Canada's licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation of the device. Manufacturer:

IKEA of Sweden AB WARNING:

Address:

Box 702, SE-343 81 lmhult, SWEDEN Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the quipment off and on, 6 the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF EXPOSURE INFORMATION According to RF exposure regulations, under normal operations the end user shall refrain from being closer than 20 cm from the device. 7 License rights and limitations NO RIGHTS OR LICENSES, EXPRESS OR IMPLIED, ARE GRANTED TO USE THIRD-

PARTY DEVICES IN COMBINATION WITH THESE PRODUCTS IN A WIRELESS MESH NETWORK, OR TO USE THIRD-

PARTY SERVICES TO ACCESS, MONITOR OR CONTROL THESE PRODUCTS IN A WIRELESS MESH NEWORK VIA THE INTERNET OR ANOTHER EXTERNAL WIDE AREA NETWORK. For use pursuant to U.S. Patent Nos.:

US 6,914,893 US 7,697,492 US 8,964,708 The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or land-fill and minimize any potential negative impact on human health and the environment. For more information, please contact your IKEA store. Franais AJOUT SOURCES LUMINEUSES AU DISPOSITIF DE COMMANDE Avant dutiliser votre source lumineuse, elle doit tre couple avec un dispositif de commande. Pour ajouter dautres sources lumineuses, il suffit de rpter les tapes ci-dessous :

1. Sassurer que la source lumineuse est installe et allume. 2. Maintenir le dispositif de commande proximit (pas plus de 5 cm) de la source lumineuse ajouter. 3. Appuyer sur le bouton de couplage et le maintenir enfonc au moins 10 secondes. Un voyant LED rouge sallume de manire continue sur le dispositif de commande. La source lumineuse baissera en intensit et clignotera une fois pour indiquer que le couplage est russi. 8 Il est possible de coupler jusqu 10 sources lumineuses 1 dispositif de commande. Veiller les coupler lune aprs lautre. Si les sources lumineuses sont proches les unes des autres, dbrancher de lalimentation gnrale celles qui ont dj t couples. MISE EN GARDE :

NE PAS UTILISER AVEC DES VARIATEURS D'INTENSIT STANDARD. Pour rgler l'intensit lumineuse de cette ampoule, utiliser uniquement le dispositif de rglage fourni avec le produit ou mentionn dans les prsentes instructions. Cette ampoule ne peut fonctionner correctement si elle est connecte un variateur d'intensit standard ( incandescence). Cette ampoule ne peut fonctionner qu'avec les produits de la gamme clairage connect IKEA. La couleur de la lumire varie entre 2 200 Kelvin (rougetre), 2 700 Kelvin

(blanc chaud) et 4 000 Kelvin (blanc froid). 8 Cet appareil est conforme larticle 15 du rglement de la FCC, ainsi quaux normes dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Son fonctionnement est autoris aux deux conditions suivantes

(1) Lappareil ne doit pas produire de RINITIALISER LAPPAREIL Actionner linterrupteur principal 6 fois. brouillage,

(2) . lappareil doit accepter tout CARACTRISTIQUES TECHNIQUES Frquence de fonctionnement : 2405 2480 MHz Puissance de sortie : 10 dBm Fabricant : IKEA of Sweden AB Adresse :

Box 702, SE-343 81 lmhult, SUDE brouillage radiolectrique subi, mme si cela est susceptible de compromettre son fonctionnement. ATTENTION :

Tout changement ou modification apports cet appareil sans approbation expresse de la partie responsable de la conformit peut 10 rendre nulle la capacit de lutilisateur utiliser cet appareil. REMARQUE :

Cet appareil a t test et il est conforme aux exigences relatives aux appareils lectroniques de classe B, selon la section 15 des rgles de la FCC (Commission fdrale des communications). Ces exigences sont prvues pour fournir une protection raisonnable contre les interfrences nuisibles dans le cas dune installation domestique. Cet appareil gnre, utilise et peut mettre de lnergie sous forme de frquences radio. Si lappareil nest pas install ou utilis conformment aux instructions, il peut provoquer des interfrences perturbant les communications radio. Il est cependant impossible de garantir labsence totale dinterfrences dune installation donne. Si cet appareil produit des interfrences nuisibles la rception radio/tlvision, ce qui peut-tre dtermin en mettant successivement lappareil sous tension et hors tension, nous conseillons lutilisateur dessayer de remdier ce problme en suivant lune des procdures suivantes :

Rorienter ou dplacer lantenne de rception. Augmenter la distance entre lappareil et le rcepteur. Brancher lappareil une prise place sur un circuit diffrent de celui auquel le rcepteur est raccord. Contacter votre revendeur ou tout technicien radio/TV qualifi pour obtenir de laide. INFORMATION SUR LEXPOSITION AUX RADIOFRQUENCES Selon la rglementation sur lexposition aux radiofrquences, dans des conditions normales dutilisation lutilisateur final ne doit pas se tenir moins de 20 cm de lappareil. 11 Le pictogramme de la poubelle barre indique que le produit doit faire l'objet d'un tri. Il doit tre recycl conformment la rglementation environnementale locale en matire de dchets. En triant les produits portant ce pictogramme, vous contribuez rduire le volume des dchets incinrs ou enfouis, et diminuer tout impact ngatif sur la sant humaine et l'environnement. Pour plus d'information, merci de contacter votre magasin IKEA. Espaol AADIR LUCES AL DISPOSITIVO DE CONTROL:

Antes de usar la luz, debers sincronizarla con un dispositivo de control. Para aadir ms luces, repite los siguientes pasos:

1. Asegrate de que la luz est instalada y de que el interruptor principal est encendido. 2. Pon el dispositivo de control cerca de la luz que quieras aadir (a menos de 5 cm). 3. Mantn presionado el botn de sincronizacin durante al menos 10 segundos. Se encender una luz roja en el dispositivo de control. Tu luz empezar a atenuarse y finalmente brillar una vez para indicar que ha sido correctamente sincronizada. 12 Se pueden sincronizar hasta 10 luces en un mismo dispositivo de control. Asegrate de sincronizarlas de una en una. Si las luces estn cerca las unas de las otras, desconecta del interruptor principal las que ya han sido sincronizadas. ATENCIN:

NO UTILIZAR CON REGULADORES DE INTENSIDAD LUMINOSA ESTNDAR. Para regular esta bombilla utiliza exclusivamente el dispositivo de control que se incluye o se especifica en las instrucciones. Esta bombilla no funciona correctamente cuando se conecta a un regulador de intensidad estndar (para bombillas incandescentes) o a un sistema de regulacin de la intensidad luminosa estndar. Slo se puede controlar con un producto de Iluminacin Inteligente de IKEA. La tonalidad de color puede variar entre 2200 K (brillo clido), 2700 K

(blanco clido) y 4000 K (blanco fro). REESTABLECER LOS AJUSTES DEL DISPOSITIVO Enciende el interruptor 6 veces. DATOS TCNICOS:

Frecuencia de operacin: 2405 2480 MHz Potencia de salida: 10 dBm Fabricante: IKEA of Sweden AB 13 Este aparato es conforme al artculo 15 del reglamento de la FCC, as como a las normas de Innovacin, Ciencia y Desarrollo econmico de Canad aplicables a los aparatos de radio exentos de licencia. Su funcionamiento est sujeto a las dos condiciones siguientes:

(1) El aparato no debe producir interferencias dainas y

(2) el aparato debe aceptar cualquier interferencia que reciba, incluidas las que puedan determinar el funcionamiento no deseado del mismo. ATENCIN:

Direccin:

Box 702, SE-343 81 lmhult, SUECIA Cualquier cambio o modificacin que se realice en este aparato sin 14 la aprobacin expresa de la parte responsable de la conformidad puede anular la capacidad del usuario para utilizar el aparato. NOTA:

Este equipo ha sido probado para comprobar que cumple los lmites establecidos en los dispositivos digitales de Clase B, segn el apartado 15 del reglamento FCC. Estos lmites se han establecido para proporcionar una proteccin razonable contra las interferencias perjudiciales en una instalacin domstica. Este equipo genera, usa e irradia energa de radiofrecuencia, y si no se instala y se usa de acuerdo con las instrucciones, puede causar interferencias perjudiciales en las comunicaciones por radio. Sin embargo no existe garanta de que no se produzcan interferencias en una instalacin en concreto. Si el equipo produjera interferencias perjudiciales en la recepcin de radio o TV, lo que se puede comprobar encendiendo y apagando el equipo, recomendamos al usuario que intente corregir dichas interferencias adoptando una o ms de las siguientes medidas:

Reorientar o recolocar la antena receptora. Aumentar la distancia entre el equipo y el receptor. Conectar el equipo a un enchufe o circuito distinto al que est conectado el receptor. Solicitar ayuda al vendedor o a un tcnico cualificado de radio/TV. INFORMACIN SOBRE LA EXPOSICIN A RF Segn la normativa sobre la exposicin a radiofrecuencias, en condiciones normales de uso el usuario final no debe estar a menos de 20 cm del aparato. 15 La imagen del cubo de basura tachado indica que el producto no debe formar parte de los residuos habituales del hogar. Se debe reciclar segn la normativa local medioambiental de eliminacin de residuos. Cuando separas los productos que llevan esta imagen, contribuyes a reducir el volumen de residuos que se incineran o se envan a vertederos y minimizas el impacto negativo sobre la salud y el medio ambiente. Para ms informacin, ponte en contacto con tu tienda IKEA. MX Importador/Distribuidor: IKEA Supply Mexico, S.A. de C.V., Av. Paseo de las Palmas 275, Int. 403404, Lomas de Chapultepec V seccin, Miguel Hidalgo C.P.: 11000 Ciudad de Mxico, Mxico, Tel. 800-1-4532 69. Lea y siga todas las instrucciones de seguridad y operacin antes de usar este producto/Para uso Interior/

Consulte Especificaciones elctricas en el etiquetado del producto. Inter IKEA Systems B.V. 2020 AA-2224196-1

TCB Authority to Act as Agent Number:

Revision:

Effective date: Oct 8, 2021 MS-0045317 0 Authority to Act as Agent Date: _2022-07-29___ TUV Rheinland of North America, Inc. 1279 Quarry Lane., Suite. A Pleasanton, CA 94566 To Whom It May Concern:

I appoint _Ms. Jessie Xu of TV Rheinland Shanghai Co., Ltd_ to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the FCC will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TUV Rheinland Group, still resides with IKEA of Sweden AB/ Box 702, SE-343 81 lmhult, Sweden. For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Agency Agreement Date:

_______2022-07-29____________ Agreement is valid for 12 months from the above date. Thank you, By:

(Signature) _____ Ivan Susak_____

(Print name) __ Product Engineering Manager _

(Title) ____ +46 476 64 85 00 _

(Telephone) On behalf of:

__ IKEA of Sweden AB __

(Company Name) Page 1 of 1

Date: 2022-07-29 Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 Subject: Request for Confidentiality Ref: FCC ID: FHO-LED2103G5 To whom it may concern:

Permanent Confidentiality Request is hereby submitted by IKEA of Sweden AB to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential:

Block Diagram Schematics Part List Short-term Confidentiality Request is hereby submitted by IKEA of Sweden AB to withhold from public review for a period of 180 days from the date of the Grant of equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC rules. In particular, the following sections of the application are to be kept confidential for a period of 180 days from the date of Authorization:

Test setup photos External photos Internal photos Users Manual Rationale for request for confidentiality:

IKEA of Sweden AB has invested considerable time and materials in research and development to produce the referenced product. [Permanent confidentiality:

Disclosure of the permanently confidential portions of the application to competitors would not only give them significant competitive advantages in develop similar products, but would also disclose successful implementation of term unpublished, confidentiality: Disclosure of the short-term confidential portions of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development. technology developed by us.]

leading edge

[Short Sincerely, _____________________ Name Ivan Susak Title Product Engineering Manager IKEA of Sweden AB E-mail Ivan.susak@inter.ikea.com Telephone number +46 476 64 85 00