FCC ID: FHO-E2002 STYRBAR Remote control

STYRBAR English Franais Espaol 4 13 22 English REMOTE CONTROL FUNCTIONS Short press to turn on. To dim up, press and hold the button. Short press to turn off. To dim down, press and hold the button. Change white spectrum, colours or scenes. 4 ADDING DEVICES TO YOUR REMOTE CONTROL When the remote control is sold together with a light source (in the same package), they are already paired. If the remote control is purchased separately, you must manually pair it to your light source. To add light sources, just repeat the steps below. Pairing: Add IKEA Smart Lighting products to your system. See instructions below. 1. Make sure that your light source is installed and the main power switch is turned on. 5 2. Hold the remote control close to the light source you want to add (no more than 5 cm away). 3. Press and hold the pairing button for at least 10 seconds. A red light will shine steadily on the remote control. Your light source will begin to dim and flash one time to indicate that it has been successfully paired. those that have already been paired from the main power switch. FACTORY RESET YOUR DEVICES For light sources:

Toggle the main switch 6 times. For remote control:

Press the pairing button within 5 seconds. 4 times Up to 10 light sources can be paired with 1 remote control. Make sure to pair them one at a time. If the light sources are close to each other, disconnect SYNCHRONIZING If your light source becomes unsynchronized, press and hold the ON/OFF button for at least 3 seconds to return the light source to its default setting (100% brightness, 2700K). CAUTION!

CHANGING THE BATTERY When the remote control is used regularly and as intended, the batteries will last for approximately 2 years. When its time to replace the battery, a red LED indicator will flash when you press any button on the remote control. Open the battery lid and replace the battery with two new AAA batteries. 6 Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. IMPORTANT!

The remote control is for indoor use only and can be used in temperatures ranging from 0C to 40 C. Do not leave the remote control in direct sunlight or near any heat source, as it may overheat. The range between the remote control and the receiver are measured in open air. Different building materials and NOTE!

Never use abrasive cleaners or chemical solvents as this can damage the product. 7 placement of the units can affect the wireless connectivity range. CARE INSTRUCTIONS To clean the remote control, wipe with a soft cloth moistened with a little mild detergent. Use another soft, dry cloth to wipe dry. Recommended battery types:

2 x IKEA LADDA 900 (AAA, 1.2V, 900mAh, Ni-MH) (Not included) Do not mix batteries of different capacities, types or date stamps. TECHNICAL DATA Type: E2001 Name: STYRBAR Remote Control stainless Type: E2002 Name: STYRBAR Remote Control white Input: 3V, 2x AAA LADDA batteries Range: 10 m in open air. For indoor use only Operating frequency: 2405-2480 MHz IP-class: IP44 8 Manufacturer: IKEA of Sweden AB Address:

Box 702, SE-343 81 lmhult, SWEDEN This device complies with Part 15 of the FCC Rules/Innovation Science and Economic Development Canada's licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation of the device. WARNING:

Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. 9 NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the quipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. 10 Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. RF EXPOSURE INFORMATION This product is approved as a portable handheld device (not body worn) This product includes a static magnet, generating a magnetic field that might interfere with the normal operation of pacemakers, defibrillators, or other medical devices. Maintain a safe distance of separation between your medical device and this device. Stop using this device and consult your physician or medical device manufacturer if you believe that it is interfering with your medical device. 11 License rights and limitations NO RIGHTS OR LICENSES, EXPRESS NO RIGHTS OR LICENSES, EXPRESS OR IMPLIED, ARE GRANTED TO USE THIRD-PARTY DEVICES IN COMBINATION WITH THESE PRODUCTS IN A WIRELESS MESH NETWORK, OR TO USE THIRD-

PARTY SERVICES TO ACCESS, MONITOR OR CONTROL THESE PRODUCTS IN A WIRELESS MESH NEWORK VIA THE INTERNET OR ANOTHER EXTERNAL WIDE AREA NETWORK. For use pursuant to U.S. Patent Nos.:

US 6,914,893 US 7,697,492 US 8,964,708 The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local 12 environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or land-fill and minimize any potential negative impact on human health and the environment. For more information, please contact your IKEA store. Franais REMOTE CONTROL FUNCTIONS Short press to turn on. To dim up, press and hold the button. Short press to turn off. To dim down, press and hold the button. Change white spectrum, colours or scenes. 13 ADDING DEVICES TO YOUR REMOTE CONTROL When the remote control is sold together with a light source (in the same package), they are already paired. If the remote control is purchased separately, you must manually pair it to your light source. To add light sources, just repeat the steps below. Pairing: Add IKEA Smart Lighting products to your system. See instructions below. 1. Make sure that your light source is installed and the main power switch is turned on. 14 2. Hold the remote control close to the light source you want to add (no more than 5 cm away). 3. Press and hold the pairing button for at least 10 seconds. A red light will shine steadily on the remote control. Your light source will begin to dim and flash one time to indicate that it has been successfully paired. those that have already been paired from the main power switch. FACTORY RESET YOUR DEVICES For light sources:

Toggle the main switch 6 times. For remote control:

Press the pairing button within 5 seconds. 4 times Up to 10 light sources can be paired with 1 remote control. Make sure to pair them one at a time. If the light sources are close to each other, disconnect SYNCHRONIZING If your light source becomes unsynchronized, press and hold the ON/OFF button for at least 3 seconds to return the light source to its default setting (100% brightness, 2700K). CAUTION!

CHANGING THE BATTERY When the remote control is used regularly and as intended, the batteries will last for approximately 2 years. When its time to replace the battery, a red LED indicator will flash when you press any button on the remote control. Open the battery lid and replace the battery with two new AAA batteries. 15 Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. IMPORTANT!

The remote control is for indoor use only and can be used in temperatures ranging from 0C to 40 C. Do not leave the remote control in direct sunlight or near any heat source, as it may overheat. The range between the remote control and the receiver are measured in open air. Different building materials and NOTE!

Never use abrasive cleaners or chemical solvents as this can damage the product. 16 placement of the units can affect the wireless connectivity range. CARE INSTRUCTIONS To clean the remote control, wipe with a soft cloth moistened with a little mild detergent. Use another soft, dry cloth to wipe dry. Recommended battery types:

2 x IKEA LADDA 900 (AAA, 1.2V, 900mAh, Ni-MH) (Not included) Do not mix batteries of different capacities, types or date stamps. TECHNICAL DATA Type: E2001 Name: STYRBAR Remote Control stainless Type: E2002 Name: STYRBAR Remote Control white Input: 3V, 2x AAA LADDA batteries Range: 10 m in open air. For indoor use only Operating frequency: 2405-2480 MHz IP-class: IP44 17 Manufacturer: IKEA of Sweden AB Address:

Box 702, SE-343 81 lmhult, SWEDEN Cet appareil est conforme larticle 15 du rglement de la FCC, ainsi quaux normes dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Son fonctionnement est autoris aux deux conditions suivantes :

(1) Lappareil ne doit pas produire de brouillage,

(2) lappareil doit accepter tout brouillage radiolectrique subi, mme si cela est susceptible de compromettre son fonctionnement. ATTENTION :

Tout changement ou modification apports cet appareil sans approbation expresse de la partie responsable de la conformit peut 18 rendre nulle la capacit de lutilisateur utiliser cet appareil. REMARQUE :

Cet appareil a t test et il est conforme aux exigences relatives aux appareils lectroniques de classe B, selon la section 15 des rgles de la FCC (Commission fdrale des communications). Ces exigences sont prvues pour fournir une protection raisonnable contre les interfrences nuisibles dans le cas dune installation domestique. Cet appareil gnre, utilise et peut mettre de lnergie sous forme de frquences radio. Si lappareil nest pas install ou utilis conformment aux instructions, il peut provoquer des interfrences perturbant les communications radio. Il est cependant impossible de garantir labsence totale dinterfrences dune installation donne. Si cet appareil produit des interfrences nuisibles la rception radio/tlvision, ce qui peut-tre dtermin en mettant successivement lappareil sous tension et hors tension, 19 nous conseillons lutilisateur dessayer de remdier ce problme en suivant lune des procdures suivantes :

Rorienter ou dplacer lantenne de Augmenter la distance entre lappareil rception. et le rcepteur. Brancher lappareil une prise place sur un circuit diffrent de celui auquel le rcepteur est raccord. Contacter votre revendeur ou tout technicien radio/TV qualifi pour obtenir de laide. 20 Maintenez une distance scuritaire entre lappareil mdical et ce produit. Si vous croyez que cet article IKEA modifie le fonctionnement de votre appareil, cessez de lutiliser et consultez votre mdecin ou le fabricant de votre appareil mdical. RENSEIGNEMENTS SUR LEXPOSITION AUX RADIOFRQUENCES Ce produit a t approuv comme appareil tenir en main (et non pas porter sur soi). Cet appareil contient un aimant gnrant un champ magntique qui pourrait nuire au fonctionnement normal des stimulateurs cardiaques, des dfibrillateurs ou dautres appareils mdicaux. 21 d'information, merci de contacter votre magasin IKEA. Le pictogramme de la poubelle barre indique que le produit doit faire l'objet d'un tri. Il doit tre recycl conformment la rglementation environnementale locale en matire de dchets. En triant les produits portant ce pictogramme, vous contribuez rduire le volume des dchets incinrs ou enfouis, et diminuer tout impact ngatif sur la sant humaine et l'environnement. Pour plus Espaol REMOTE CONTROL FUNCTIONS Short press to turn on. To dim up, press and hold the button. Short press to turn off. To dim down, press and hold the button. Change white spectrum, colours or scenes. 22 ADDING DEVICES TO YOUR REMOTE CONTROL When the remote control is sold together with a light source (in the same package), they are already paired. If the remote control is purchased separately, you must manually pair it to your light source. To add light sources, just repeat the steps below. Pairing: Add IKEA Smart Lighting products to your system. See instructions below. 1. Make sure that your light source is installed and the main power switch is turned on. 23 2. Hold the remote control close to the light source you want to add (no more than 5 cm away). 3. Press and hold the pairing button for at least 10 seconds. A red light will shine steadily on the remote control. Your light source will begin to dim and flash one time to indicate that it has been successfully paired. those that have already been paired from the main power switch. FACTORY RESET YOUR DEVICES For light sources:

Toggle the main switch 6 times. For remote control:

Press the pairing button within 5 seconds. 4 times Up to 10 light sources can be paired with 1 remote control. Make sure to pair them one at a time. If the light sources are close to each other, disconnect SYNCHRONIZING If your light source becomes unsynchronized, press and hold the ON/OFF button for at least 3 seconds to return the light source to its default setting (100% brightness, 2700K). CAUTION!

CHANGING THE BATTERY When the remote control is used regularly and as intended, the batteries will last for approximately 2 years. When its time to replace the battery, a red LED indicator will flash when you press any button on the remote control. Open the battery lid and replace the battery with two new AAA batteries. 24 Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. IMPORTANT!

The remote control is for indoor use only and can be used in temperatures ranging from 0C to 40 C. Do not leave the remote control in direct sunlight or near any heat source, as it may overheat. The range between the remote control and the receiver are measured in open air. Different building materials and NOTE!

Never use abrasive cleaners or chemical solvents as this can damage the product. 25 placement of the units can affect the wireless connectivity range. CARE INSTRUCTIONS To clean the remote control, wipe with a soft cloth moistened with a little mild detergent. Use another soft, dry cloth to wipe dry. Recommended battery types:

2 x IKEA LADDA 900 (AAA, 1.2V, 900mAh, Ni-MH) (Not included) Do not mix batteries of different capacities, types or date stamps. TECHNICAL DATA Type: E2001 Name: STYRBAR Remote Control stainless Type: E2002 Name: STYRBAR Remote Control white Input: 3V, 2x AAA LADDA batteries Range: 10 m in open air. For indoor use only Operating frequency: 2405-2480 MHz IP-class: IP44 26 Manufacturer: IKEA of Sweden AB Address:

Box 702, SE-343 81 lmhult, SWEDEN Este aparato es conforme al artculo 15 del reglamento de la FCC, as como a las normas de Innovacin, Ciencia y Desarrollo econmico de Canad aplicables a los aparatos de radio exentos de licencia. Su funcionamiento est sujeto a las dos condiciones siguientes:

(1) El aparato no debe producir interferencias dainas y

(2) el aparato debe aceptar cualquier interferencia que reciba, incluidas las que puedan determinar el funcionamiento no deseado del mismo. ATENCIN:

Cualquier cambio o modificacin que se realice en este aparato sin la aprobacin expresa de la parte responsable de la 27 conformidad puede anular la capacidad del usuario para utilizar el aparato. NOTA:

Este equipo ha sido probado para comprobar que cumple los lmites establecidos en los dispositivos digitales de Clase B, segn el apartado 15 del reglamento FCC. Estos lmites se han establecido para proporcionar una proteccin razonable contra las interferencias perjudiciales en una instalacin domstica. Este equipo genera, usa e irradia energa de radiofrecuencia, y si no se instala y se usa de acuerdo con las instrucciones, puede causar interferencias perjudiciales en las comunicaciones por radio. Sin embargo no existe garanta de que no se produzcan interferencias en una instalacin en concreto. Si el equipo produjera interferencias perjudiciales en la recepcin de radio o TV, lo que se puede comprobar encendiendo y apagando el equipo, recomendamos al usuario que intente corregir dichas 28 interferencias adoptando una o ms de las siguientes medidas:

Reorientar o recolocar la antena Aumentar la distancia entre el equipo receptora. y el receptor. Conectar el equipo a un enchufe o circuito distinto al que est conectado el receptor. Solicitar ayuda al vendedor o a un tcnico cualificado de radio/TV. 29 Mantn una distancia segura entre tu aparato mdico y este aparato. Deja de usar este aparato y ponte en contacto con tu mdico o con el fabricante del aparato mdico si piensas que est interfiriendo con tu aparato mdico. INFORMACIN SOBRE LA EXPOSICIN A RF Este producto ha sido aprobado para utilizarse como un aparato porttil (no se debe llevar pegado al cuerpo) Este producto incluye un imn esttico, lo que genera un campo magntico que puede interferir con la operacin normal de marcapasos, desfibriladores y otros aparatos mdicos. 30 medio ambiente. Para ms informacin, ponte en contacto con tu tienda IKEA. La imagen del cubo de basura tachado indica que el producto no debe formar parte de los residuos habituales del hogar. Se debe reciclar segn la normativa local medioambiental de eliminacin de residuos. Cuando separas los productos que llevan esta imagen, contribuyes a reducir el volumen de residuos que se incineran o se envan a vertederos y minimizas el impacto negativo sobre la salud y el MX Importador/Distribuidor: IKEA Supply Mexico, S.A. de C.V., Av. Paseo de las Palmas 275, Int. 403404, Lomas de Chapultepec V seccin, Miguel Hidalgo C.P.: 11000 Ciudad de Mxico, Mxico, Tel. 800-1-4532 69. Lea y siga todas las instrucciones de seguridad y operacin antes de usar este producto/Para uso Interior/

Consulte Especificaciones elctricas en el etiquetado del producto. Inter IKEA Systems B.V. 2020 AA-XXXXXXX-1

R TYPE: E2002 STYRBAR Remote control white FCC ID:FHO-E2002 Contains FCC ID:QOQMGM210L CAN ICES-3 (B)/NMB-3(B) Contains IC:5123A-MGM210L IFT:XXXXXX TVRheinland C US outside label inside label E2002 NA MARKING

Standard Form Number:

MS-0004558 Version:

Page:

2.1 1 of 1 Sample Agency Request Letter The following is a sample Agency Request letter, which needs to be completed on company letterhead, signed by an authorized Applicant/Agent, and submitted to TV Rheinland. Authority to Act as Agent Date: 20200424 TUV Rheinland of North America, Inc. 1279 Quarry Ln., Ste. A Pleasanton, CA 94566 To Whom It May Concern:

I appoint TUV Rheinland of North America, Inc to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the FCC or Industry Canadas regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by TUV Rheinland Group, still resides with IKEA of Sweden AB, Box 702, lmhult, SWEDEN For TCB applications, We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: 20210424 Ivan Susak Team Manager, Laws&Standards IKEA of Sweden AB Ivan.susak@ikea.com

+4647681000 This document is issued in strict confidence and shall not be reproduced, copied, or otherwise used without the expressed written consent of Printed: Mai 4, 2020 Approved Documents Valid 2 Days Verify as current revision when invalid. the Management of TV Rheinland Industrial Solutions, Inc.

April 24, 2020 Attention: Application Examiner RE:

Request for Confidentiality Applicant: IKEA of Sweden AB FCC ID: FHO-E2001 and FHO-E2002 To Whom It May Concern:

Permanent Confidentiality Request is hereby submitted by IKEA of Sweden AB to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential:

Schematics Detailed Block Diagrams Detailed Operational/Functional Description Short-term Confidentiality Request is hereby submitted by IKEA of Sweden AB to withhold from public review for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing, certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept confidential for a period of 180 days from the date of Authorization:

Test setup photos External photos Internal photos Rationale for request for confidentiality:

IKEA of Sweden AB has invested considerable time and materials in research and development to produce the referenced product. [Permanent confidentiality: Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us.] [Short term confidentiality: Disclosure of the short-term confidential Inter IKEA Systems B.V. 2014 portions of this application during the period of importation and/or distribution would reveal key aspects of proprietary technology to competitors and diminish the value of our investment in research and development.]

Ivan Susak Team Manager Laws & standards IKEA of Sweden AB Ivan.susak@ikea.com

+4647681000 Sincerely, Inter IKEA Systems B.V. 2014