FCC ID: FHO-920-00632 Wireless Device

1(5) 30 March 2021 User manual for IKEA | Sonos Wireless module FCC ID: FHO-920-00632 and IC: 10912A-92000632 Module description: There are two different radios in the Wireless Module. The first radio supports WiFi wireless Ethernet based on the IEEE 802.11 a/b/g/n standards. The 2.4 GHz communication is limited to channels 1-11 for North America. The 5 GHz communication is controlled based on regional regulatory requirements. The second radio supports Bluetooth Low Energy (BLE) mode (v4.2). Support for BLE is through a dedicated chip. Operation in BLE mode is supported in the required 2.4 GHz ISM band on channels 0-39. In addition to the radios, the Wireless Module supports wired Ethernet communication (IEEE 802.3 100Base-TX) by using Ethernet port. In this mode of operation, the WiFi wireless Ethernet is disabled. Note: Wireless Module labeled with FCC ID: FHO-920-00632 is not capable of transmitting on 2.4GHz Channels 12 & 13. This FCC ID does not appear on the product label of non-USA product versions

(SKUs). IMPORTANT SAFETY INSTRUCTIONS IMPORTAN INSTRUCTION SAFET When using an electrical device, basic precautions should always be followed, including the following:

When using an electrical device, basic precautions should always be followed, including the following:

To reduce the risk of burns, fire, electric shock, or injury to persons:

To r educe the risk of burns, fire, electric shock, or injury to persons:

1. Unplug from outlet before putting on or taking off parts. 1 Unplug from outlet before putting on or taking off parts. 2. Close supervision is necessary when this device is used by, or near children, invalids, or Close supervision is necessary when this device is used by, or near chil dren, invalids, or 2 disabled persons. disabled persons. 3. Never operate this device if it has a damaged cord or plug, if it is not working properly, if it has Never operate this device if it has a damaged cord or plug, if it is not working properly, if it has 3 been dropped or damaged, or dropped into water. Return the device to a service center for been dropped or damaged, or dropped into water. Return the device to a service center for examination and repair. examination and repair. 4. Keep the cord away from heated surfaces. 4 Kee the cord away from heated surfaces. 5. Do not use outdoors. 5 Do not use outdoors. IKEA of Sweden AB Tulpanvgen 1 Box 702 343 81 lmhult, Sweden Telephone: +46(0)47681000 Org.nr: 556074-7551 2(5) 30 March 2021 Advice and instructions for Wireless Module:

Advice and instructions for Wireless Module Sound level: Lower than 55 dB(A). Sound level: Lower than 55 dB(A). Temperature interval at usage: +10 C up to + 40 C/+50 up to +104 F. Temperature interval at usage: +10 C up to + 40 C/+50 up to +104 F. Temperature interval at storage: -18C up to 70C/0 up to 158F. Temperature interval at storage: 18C up to 70C/0 up to 158F. Humidity: 20% up to 90% at 40C/104F. Humidity: 20% up to 90% at 40C/104F. Power supply unit: The module is power by a specified DC supply that is mains connected. The power Power supply unit: The module is power by a specified DC supply that is mains connected. The power supply is certified for its intended usage and evaluated for supply is certified for its intended usage and evaluated for safety. Model: 92 00632 Model: 920-00632 This appliance shall only be used together with the matching DC power supply. This appli ance shall only be used together with the matching DC power supply. Installation instructions:

Installation instructions

Install module in host product with screws and hand tighten. Install all connectors from the Install module in host product screws and hand tighten. Install all connectors from the host product to the wireless module. host product to the wireless module. Place the electrical cables so that they do not get damaged, see assembly instruction. Place the electrical so that they do not get damaged, see assembly instruction. Connect the electrical cable to a wall socket. socket. Connect the electrical cable to a Usage of the Wireless Module:

Usage of the Wireless Module The wireless module can only be used within the scope of approval within the country from The wireless module can only be used within the scope of approval within the country from where the authorization was granted. IKEA strongly discourages the use of the wireless module where the authorization was granted. IKEA strongly discourages the use of the wireless module outside the bounds of the equipment authorization. This device can only be used with IKEA outside the bounds of the equipment authorization. This device can only be used with IKEA approved antenna with characteristics and gain that is compatible with the equipment approved antenna with characteristics and gain that is compatible with the equipment authorization. authorization Tulpanvgen 1 Box 702 343 81 lmhult, Sweden Telephone: +46(0)47681000 Org.nr: 556074-7551 3(5) Changes or modifications not expressly approved by IKEA could void the user's authority to operate the equipment. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. To ensure compliance with FCC and ISED RF exposure requirements this device must be installed to provide a minimum of 20cm between the device and people. Pour garantir la conformit aux exigences d'exposition RF de la FCC et d'ISED Canada, cet appareil doit tre install de manire laisser un minimum de 20 cm entre l'appareil et les personnes. Tulpanvgen 1 Box 702 343 81 lmhult, Sweden Telephone: +46(0)47681000 Org.nr: 556074-7551 5(5) 30 March 2021 SAFETY REGULATIONS SAFETY REGULATIONS Maintenance and repair instructions:

Ma ntenance and repair instructions

If any part of the electrical system is replaced, the electrical cable must first be disconnected If any part of the electrical system is replaced, the electrical cable must be disconnected from the wall socket. Replace the electrical part and then connect the electrical cable to the from the wall socket. Replace the electrical part and then connect the electrical cable to the wall socket. The product is now ready for use. f the product still does not work, please contact wal product is now ready for use. If the product still does not work, please contac your nearest IKEA store r customer service. customer service. your nearest IKEA store o socket. Th PRODUCT SERVICING PRODUCT SERVICING Do not attempt to repair this product yourself, as opening or removing covers may expose you to Do not attempt to repair this product yourself, as opening or removing may expose you to dangerous voltage points or other risks. dangerous voltage points or other risks. Manufacturer:

Manufacturer:

IKEA of Sweden AB Address:

Box 702, SE-343 81 LMHULT SAVE THESE INSTRUCTIONS SAVE THESE INSTRUCTIONS This device complies with Part 15 of the FCC Rules/Industry Canada license-exempt RSS standard(s). This device complies with Part 15 of the FCC Rules/Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions:

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(1) this device may not cause harmful int rference, and

(2) this device must accept any interference received, including interference that may cause

(2) this device must accept any may cause undesired operation of the device. undesired operation of the device. received, including interference not expressly approved by the party WARNING:

WARNING Any changes or modifications to this unit not expressly approved by the party responsible for Any changes or modifications to this unit responsible for compliance could void the users authority to operate the equipment. compliance could void the users authority to operate the NOTE:

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonabl e protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur interference to radio commu nications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television in a particular installation. If this equipment does harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try reception, which can be determined turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following easures to correct the interference by one or more of the measures:

Reorient or relocate the receiving antenna Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is Connect the equipment into an outlet on a circuit differ ent from that to which the receiver is connected. connected. Consult the dealer or an experienced radio/TV technician for help. Consult the dealer or an experienced radio/TV technician for help. IKEA of Sweden AB Tulpanvgen 1 Box 702 343 81 lmhult, Sweden Telephone: +46(0)47681000 Org.nr: 556074-7551 5(5) 30 March 2021 The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from The out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or landfill and minimize any potential negative impact the volume of waste sent to incinerators or landfill an human health and the environment. For more information, please contact your IKEA store human health and the environment. For more information, please contact your IKEA store. minimize any potential negative i pac o IKEA of Sweden AB Tulpanvgen 1 Box 702 343 81 lmhult, Sweden Telephone: +46(0)47681000 Org.nr: 556074-7551

Label Location Model: 920-00632 Top side view Marking for the module:

FCC ID: FHO-920-00632 IC: 10912A-92000632

Applicant/Grantee FCC ID:

IKEA of Sweden AB FHO-920-00632 Request for Modular Approval Request for Limited Modular Approval Requirements EUT Conditions Comply (Y/N) Single Modular Approval Requirements Section 15.212 Modular Transmitters Y Y Y Y Y 1 2 3 4 5 The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. The modular transmitter must have its own power supply regulation. The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a unique antenna coupler (at all connections between the module and the antenna, including the cable). The professional installation provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting 6 7 equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available

(see Section 15.31(i)). The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number.

(A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: XYZMODEL1 or Contains FCC ID:

XYZMODEL1. Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization.

(B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following:

Contains FCC certified transmitter module(s). Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. Y Y 8 The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. Y A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured.

Date: March 11, 2021 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject:

FCC ID:

To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting, for IKEA of Sweden AB, the Commission withhold the following submissions documents as confidential documents from public disclosure indefinitely. Request for Confidentiality (Long and Short Term) FHO-920-00632 Schematic Diagrams Block Diagram(s) Theory of Operation Antenna Specifications Channel Plan Software Security Statement (5 GHz) Those documents contain detailed system and equipment description and related information about the product which IKEA of Sweden AB considers to be confidential, proprietary, a custom design and, otherwise, not releasable to the general public. Since this design is a basis from which future technological products will evolve, IKEA of Sweden AB considers that this information would be of benefit to its competitors, and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request of 180 days for:

External Photos Internal Photos Product Test Setup Photos User manual 1 It is our understanding that all measurement test reports, FCC ID label format and correspondence during certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Best regards, David Petry Sonos | Director of Compliance Engineering | 631 384 9633 | David.Petry@sonos.com 2

Date: March 7, 2021 UL Verification Services Inc. 47173 Benicia Street Fremont, CA 94538, USA RE: FCC authorization for IKEA 920-00632 and E1913 To whom it may concern:

I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which certification has been granted;

do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

b) c) d) e) 614 Chapala Street Santa Barbara, CA 93101 T (+1) 805 965 3001 F (+1) 805 965 3010 www.sonos.com f) g) h) i) j) use certification only to indicate the products are certified as being in conformity with specified standards;

endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Best regards, David Petry Sonos Inc. | Director of Compliance Engineering | 805 308-8029 | David.Petry@sonos.com 614 Chapala Street Santa Barbara, CA 93101 T (+1) 805 965 3001 F (+1) 805 965 3010 www.sonos.com

To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 1(1) 25 February 2021 To Whom It May Concern:

The IKEA of Sweden AB the undersigned, hereby authorizes David Petry of sonos, to act on the behalf of the IKEA of Sweden AB solely in matters relating to the application for an FCC equipment authorization for FCC IDs: FHO-E1922, FHO-E1915, FHO-E1913 and FHO-920-00632 including the signing of documents in connection with these Applications. Necessary acts carried out by IKEA of Sweden AB on our behalf of the IKEA of Sweden AB in connection with these Applications shall have the same effect as acts of the IKEA of Sweden AB. The IKEA of Sweden AB also hereby certify that no party to these applications are subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Thank you for your attention to this matter. Yours Sincerely, Signature: __________________________________ Ivan Susak Business Area Product Engineering Manager Ivan susak Ivan susak (Feb 25, 2021 11:34 GMT+1) IKEA of Sweden AB Tulpanvgen 1 Box 702 343 81 lmhult, Sweden Telephone: +46(0)47681000 Org.nr: 556074-7551