FCC ID: 2BA22-IS-200 RFID Module (13.56 MHz)

RFID READER USER MANUAL MODEL : IS-200 Safety Instructions A1 Product Configuration B1~2 Full Configuration and Specifications....................................... B-1 Function Description.............................................................. B-2 How to Install C1 How to Install........................................................................C-1 How to Operate How to Operate.............. .....................................................D-1 Safety Instructions Cautions

Do not install it under direct sunlight. Do not install it where the ambient temperature is too high or low. Do not install it where is too humid. Do not install it where the power is not stable. Do not impact it externally. Care must be taken not to allow water or debris infiltrated in it. Do not spill alcohol or benzene over it. Do not assemble or repair it. Prior to use, check if the adaptor and the power are correct. Note The contents in this manual are subject to change without notice for product feature enhancement. A-1 Product Configuration 1. Full Configuration and Specifications 1. Full Configuration and Specifications NFC Reader Module IS-200 Item Name Appearance 1. Terminal : 1 EA Components 2. Manual : 1 EA 3. Cable : 1 EA (Terminal with Cable) Feature

- RF Reader for Card Recognition Specifications Classification Content Remark CPU Frequency Pulse Communication Oscillation Modulation Power Output Environment

(Transmit/Receive) 32Bit ARM Core 13.56MHz A1D RS232 [115200 BPS]

X-Tal method ASK DC +5V Less than 200uV/M 0~+70, less than 90%

B-1 Product Configuration 2. Function Description 2. Function Description 1) Contents The product supplied contains followings IS-200 RS232 Cable 2) Parts Names LED: RED & BLUE BUZZER 5Pin Connector B-2 How to Install 1. How to Install 1. How to Install l Install it on the flat side where to be used. lTurn off the power of the external device. lConnect the communication cable to the communication port of the external device.

(External devices : Computer or Device) C-1 How to Operate l When the power is supplied, [RED] lamp is lit and it is ready to receive command from the external device. l When the reader recognizes the card, [BULE] lamp is lit. l When the reader recognizes the card, [Beep] buzzer sounds. D-1 FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &

your body. OEM INTEGRATION INSTRUCTIONS:

This device is intended only for OEM integrators under the following conditions:

The module must be installed in the host equipment such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna. The module shall be only used with the internal on-board antenna that has been originally tested and certified with this module. External antennas are not supported. As long as these 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). The end-product may need Verification testing, Declaration of Conformity testing, a Permissive Class II Change or new Certification. Please involve a FCC certification specialist in order to determine what will be exactly applicable for the end-product. Validity of using the module certification:

In the event that these conditions cannot be met (for example certain laptop configurations or co-

location with another transmitter), then the FCC authorization for this module in combination with the host equipment is no longer considered valid and the FCC ID of the module cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. In such cases, please involve a FCC certification specialist in order to determine if a Permissive Class II Change or new Certification is required. Upgrade Firmware:

The software provided for firmware upgrade will not be capable to affect any RF parameters as certified for the FCC for this module, in order to prevent compliance issues. End product labeling:

This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID: 2BA22-IS-200. Information that must be placed in the end user manual:

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user's manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6591890.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Label & Location Iksung Electronics Model name: IS-200-L FCC ID : 2BA22-IS-200 Front Iksung Electronics Model name: IS-200-S FCC ID : 2BA22-IS-200 Front

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6591895.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Iksung Electronics R207, Daegu D Center 1976 Knowledge Industry Center, 307, Waryong-ro, Seo-gu, Daegu, Republic of Korea May 25, 2023 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Letter of Authorization We, the undersigned, hereby authorize Jong-Myoung, Shin of EMC Labs Co., Ltd. to act on our behalf in all manners relating to application for equipment authorization for FCC ID: 2BA22-IS-200 including signing of all documents relating to these matters. Any and all acts carried out by Jong-Myoung, Shin of EMC Labs Co., Ltd. on our behalf shall have the same affect as acts of our own. This authorization is valid until further written notice from Iksung Electronics. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Sincerely, ChaHwan, Jee / CEO

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6591893.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Iksung Electronics R207, Daegu D Center 1976 Knowledge Industry Center, 307, Waryong-ro, Seo-gu, Daegu, Republic of Korea Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2023-05-25 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2BA22-IS-200

[Iksung Electronics] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, ChaHwan, Jee / CEO Rev 1/26/2023 Iksung Electronics R207, Daegu D Center 1976 Knowledge Industry Center, 307, Waryong-ro, Seo-gu, Daegu, Republic of Korea Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 2023-05-25 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2BA22-IS-200

[Iksung Electronics] (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely, ChaHwan, Jee / CEO Rev 1/26/2023

Iksung Electronics R207, Daegu D Center 1976 Knowledge Industry Center, 307, Waryong-ro, Seo-gu, Daegu, Republic of Korea Date: 2023-06-02 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BA22-IS-200 US Agent Attestation Statement / Part 2.911(d)(7) Iksung Electronics certifies, that as of 2023-06-02, we have designated FCC US Agent, LLC to accept service of process on our behalf for FCC ID: 2BA22-IS-200. Iksung Electronics, accepts to maintain an agent of service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-

related administrative or judicial proceeding involving the equipment, whichever is later. FCC US Agent, LLC, accepts as of the date of the filing of this application, the obligation of being the designated agent for the purpose of accepting service of process on behalf of Iksung Electronics for FCC ID: 2BA22-IS-200. Designated Agent Information:

Company Name: FCC US Agent, LLC FRN: 0033402884 Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Contact Person: Tim Payne Phone: 708-571-3148 Email: Support@FCCUSAgent.com Sincerely, Company: Iksung Electronics Designated Agent: FCC US Agent, LLC Company Representative: ChaHwan, Jee Designated Agent Representative: Tim Payne Signature:

Signature:

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6591892.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Iksung Electronics R207, Daegu D Center 1976 Knowledge Industry Center, 307, Waryong-ro, Seo-gu, Daegu, Republic of Korea Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2BA22-IS-200 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Block Diagram Schematics Operational Description Part List File Name

[IS-200-L] BLK

[IS-200-L] SCH

[IS-200-L] OpDes

[IS-200-L] Part List The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

Exhibit Type External Photos Internal Photos Test Setup Photos Manual File Name

[IS-200-L] EXT Photo

[IS-200-L] INT Photo

[IS-200-L] Test Setup Photo

[IS-200-L] Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. Sincerely, ChaHwan, Jee / CEO

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6591891.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Iksung Electronics R207, Daegu D Center 1976 Knowledge Industry Center, 307, Waryong-ro, Seo-gu, Daegu, Republic of Korea May 25, 2023 SENA TECHNOLOGIES.Inc Applicant: Iksung Electronics FCC ID: 2BA22-IS-200 To. Whom it may concern:

There are no changes in the circuital and electronic feature, and in the technical data provided in the submitted document. There are difference just PCB Size, between Basic model and Additional model.

(Refer to the EXT Photo and INT Photo for PCB Size) Basic model Additional model IS-200-L IS-200-S Sincerely, ChaHwan, Jee / CEO

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6591885.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Iksung Electronics R207, Daegu D Center 1976 Knowledge Industry Center, 307, Waryong-ro, Seo-gu, Daegu, Republic of Korea May 25, 2023 Modular Approval Request Letter Applicant: Iksung Electronics FCC ID: 2BA22-IS-200 Item Modular requirement Yes No 1 2 3 4 5 6 7 The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly;

The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal;

The module must contain power supply regulation on the module;

The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b);

The module must demonstrate compliance in a stand-alone configuration;

The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements);

The module must comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee;

8 The module must comply with RF exposure requirements Yes Yes Yes Yes Yes Yes Yes Yes Sincerely, ChaHwan, Jee / CEO