Answering incoming calls when MIC amplifier mode is on When you wear the Pendant and using the MIC amplifier mode and there is an incoming call presented, the Pendant will ring and vibrate. Press $1 will answer the call. MIC Amplifier willturn off automatically and resume again after phone call. Transferring calls (For Nokia N5700 or equivalent models) When you are in session, calls can be transferred from the Bluetooth phone to the Pendant and from the Pendantto the Bluetooth phone. e To transfer a call from Bluetooth mobile phone to the Pendant:
press S1 once, the call will be transferred to Pendant. e Totransfer acall from Pendant to Bluetooth mobile phone, please follow the operating instructions of your mobile phone. Ending calls While a callis in session on the Pendant, pressing S11 will disconnect the call. After the call is disconnect, the blue LED will flash normally again. To make a new call using voice dial Make sure the voice dialing function is set up in the mobile phone and itis within the range of the Pendant.Press $1 on the Pendant shortly. There is abeep tone on the Pendant. Then use your recorded voice commands(e.g.By saying the name of the person). The call will be connected in a few seconds. Reject a call To reject a call at the time when the Pendant rings & vibrates, press and hold $1 until you hear a tone. TV listening kit (optional external cable) Optional TV listening kit includes a 12 feet external cable to extend Pendant microphone. To use Pendant for TV listening:
1,Plug the external cable to external microphone socket 2,Place the microphone of external cable close to TV speaker Caution: Please be cautious of the cable between Pendant and TV set. Low-battery indication The Pendant LED will flash red instead of blue when the battery is low, There will also a short beep periodically. After this indication you still have up to 15 minutes talk time. When the battery levelis too low, the Pendant will power off. It cannot power on again unless the charger is connected or the battery is sufficiently charged, Battery recharging To recharge the battery, connect the charger cable to the Pendant. During recharging, the LED shows a steady red light. When the battery is fully charged, the red light will be off. The achievable talk time and standby time for the Pendant can vary with different Bluetoth mobile phones due to different implementation of power down modes. Keep the Pendant away from the fire to avoid damage. Warning:
For adaptor, the socket-outlet shall be installed near the equipment and shall be easily accessible. 10 Led status LED Status 1x1 Sec, Blue Ready can be accessed by paired devices 1x2 Sec. Blue Paired and connecting to BT device 1x3 Sec. Blue Talking Blinking Red Battery low (Max 15 Minutes left) Red LED on Under charging Red LED off Fully charged Red/Blue Blinking Pairing-mode Remaining:
When the battery is low, the LED will not turn on until the Pendant is charged up, which may takes several minutes. Trouble shooting guide No sound 1,Please check earphone is plugged and locked to Pendant properly 2.Please check battery is powered. 3.Please check Pendant is turned on. 4.Please check volume level is appropriated to you. 5,Please check the tone frequency is appropriated to you. Weak sound 1,Please check volume level is appropriated to you. 2,Please check the tone frequency is appropriated to you, 3.Please check battery is powered. 4,Please check your mobile phone volume level and mobile phone network signal is sound. Maintenance and care 1,Keep the Pendant out of the reach of children 2,Store the Pendant is dry condition 3.Do not expose the Pendant to excessive moisture,humidity or steam. 4.Avoid dropping or knocking the Pendant. 5,Avoid electric shock by keeping the Pendant away from water. 6.Do not clean with harsh chemicals, cleaning solvents or abrasive detergents. To clean, wipe with soft cloth slightly. 12 Content table Picture Description Pendant A/C Power Adaptor Earphone Neckloop External Microphone 13 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-
mined by turning the equipment off and on,the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver,
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 14 IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance, To main-
tain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter, Correct Disposal of this product This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of ME inaterial resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling. 15 Declaration of Conformity We, Company: IN-TECH ELECTRONICS LTD. With our, Product(s): BLUETOOTH HEARING ENHANCER Model No.: cs8141 herewith confirm to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to the R&TTE Directive (1999/5/EC) as well as to the Low Voltage Directive 2006/95/EC,. For the evaluation of above mentioned Directives, the following standards were applied:
EMC EN 301 489-17 V1.3.2 (2008-04) EN 301 489-1 V1.8.1 (2008-04) EN55022: 2006 EN61000-3-2: 2006 EN61000-3-3: 1995+A1+A2 EN50371:2002 EN 300 328 V1.7.1 (2006-10) LVD EN60950-1 : 2006 The following manufacturer is responsible for this declaration:
In-Tech Electronics Ltd Unit A, 13/F, Wing Tai Centre, 12 Hing Yip Street, Kwun Tong, Kowloon, Hong Kong. 16 o=<= a4 wewonow - we Ww a
= 0D wv Dy =o ST oY