INCYNC Bluetooth stereo headset Users manual Welcome to use this Bluetooth stereo headset, INCYNC. Please read this users manual carefully before use.
Brief introduction INCYNC is a mini Bluetooth stereo speaker and a Bluetooth hand-free device. You can use it to enjoy wireless music and make a call at the same time. It mainly used in peaked cap.
Before use 1. Overview 1 LED indicator 2 Volume up/Last track 3 Line out jack/charging jack 4 Volume down/Next track 5 Multi-functions button 6 Microphone 7 Loudspeaker 1 Contents
Brief introduction.........1
Before use..1 1. Overview...1 2. Charging for headset..2
Getting started..3 1. Turning on/off the headset..........3 2. Wearing the headset.......................................................................3 3. Pairing/connecting..................................4 1) How to enter pairing mode .......................4 2) Pairing headset with Bluetooth cell phone .................4 3) Pairing headset with Bluetooth transmitter..............................5 4. Making a call with the headset....6 5. Playing music.....7 6. Line out........................................................................................8 7. LED indicator.........8 8. Factory Reset....9
Care and maintenance.....9
FAQs.....10
Specification.....11
FCC/IC Statement...11 2. Charging for headset The headset comes with a built-in rechargeable battery, prior to using it, it is recommended to charge the battery fully for the first time. When the headset is low power, the headset emits thrice every 30 seconds and the red LED flashes twice every 30 seconds. Please recharge the battery of the headset. The way of charging as following:
1. Turn on the cover of charging jack, and plug the USB charging cable. 2. Plug another side of cable to the USB port of PC Red light on: Charging Red light off: Finish charging 3. It will takes about 3 hours to finish charging excessive heat place, such as sunshine, fire or the like. Remarks:
1) The battery is recyclable. 2) Batteries (battery pack or batteries installed) shall not be exposed to 2
Getting started 1. Turning on/off the headset Functio ns Turning on Turning off Reset turn off Operation Press and hold MFB for 4 seconds Press and hold MFB for 4 seconds and Short press button LED indictor Blue LED on for 1 second Red LED on for 1 second LED indictor goes out Prompt tone Oner long tone One long tone No prompt tone Remark: In order to save power, the headset will turn off automatically if no devices can be connected after 5 minutes. 2. Wearing the headset As a mini Bluetooth speaker and also a Bluetooth hand-free device. The INCYNC mainly been worn in cap. Please reference the pictures as shown below. The side with button should towards up. The side with loudspeaker should towards down. Making the U buckle clamps the brim of the cap . 3 3. Pairing/connecting 1) How to enter pairing mode Operation Press and hold MFB for 8 seconds Functions Enter pairing mode LED indictor Blue LED and red LED flash alternately Prompt tone Twodudutone 2) Pairing headset with Bluetooth cell phone Prior to using the headset for the first time, you have to pair it with a Bluetooth-enabled cell phone. The pairing procedures are subject to different models of cell phones. Please refer to your cell phone users manual for further information. The general pairing procedures are as follows:
1) Keep the cell phone and the INCYNC within 1 meter when pairing;
2) Make the INCYNC enter pairing mode (Please refer to How to enter pairing mode);
3) Active the Bluetooth function of your cell phone and make it enter pairing mode. It will search for Bluetooth devices automatically and send a pairing request. After successful pairing and connecting, blue LED of the INCYNC flashes thrice every 4 seconds. Remarks:
After successful pairing, the paired devices will remember each other, they will no need to pair next time. The headset will connect with last connected device automatically when you turn it on again.
When the headset not connected with device, short press MFB button once, the headset will try to connect with last connected device.
After enter pairing mode , the headset would not connect automatically. If you need to pair it with other devices, please pair the headset with new device according to the steps mentioned above. 4 the 3Pairing headset with Bluetooth transmitter You can connect the headset with a Bluetooth transmitter to enjoy music wirelessly. Hereby take BTT005 for example (not included in accessory). The pairing steps are as follows:
(1)Keep INCYNC and Bluetooth transmitter within 1 meter when pairing, the closer the better.
(2)Make the INCYNC enter pairing mode.
(Please refer to How to enter pairing mode.)
(3)Turn on the Bluetooth transmitter and make it enter pairing mode. It will search for Bluetooth devices automatically and send a pairing request; After successful pairing and connecting, blue LED of the headset flashes twice every 4 seconds. Remarks:
The pairing password of the headset is 0000. So, the headset can only pair with a Bluetooth transmitter whose pairing password is 0000. The headset does not support the Bluetooth transmitter whose pairing password is not 0000.
After successful pairing, the paired devices will remember each other, they will no need to pair next time. The headset will connect with last connected device automatically when you turn it on again.
If you fail to pair for many times, please read the users manual of Bluetooth transmitter carefully. 5 Operation once Short press once Short press Long press about 2 seconds and release it until listen a tone once Short press Short or long press button Short or long press button Long press about 2 seconds and release it until listen a tone about 2 Long press seconds and release it until listen a tone Double click button Double click button Long press about 2 seconds and release it until listen a tone Double click button 4. Making a call with the headset 1) Basic operation Functions Cancel a call Answer a call Reject a call Status of headset Calling Incoming call ringing Incoming call ringing End a call Volume up During a call During a call Volume down During a call Transfer conversation to mobile phone Transfer conversation to headset Microphone mute Cancel mute Voice dial During a call During a call During a call During a call
(microphone mute) Standby mode
(connected device) Redial the last number Standby mode
(connected device) 6 2)Three-ways call operation Functions Answer new call and end current call Answer new call and retain current call Switch calls End current call and switch retain call Status of headset During a call, there are second incoming call Incoming ringing Operation Short press once Double click Keep conversation and another call retains Keep conversation and another call retains Double click Short press once Remarks:
When the volume is adjusted to max or min, you will hear one prompt
You will hear dudu tone twice every 5 seconds when the microphone tone. mutes.
When pressing the answer button on some mobile phones, the call will be transferred to the mobile phone. You can switch the call to the headset by using the conversation switch button or through operating on the mobile phone. Please refer to your cell phone user manual for further information. 5. Playing music Functions Status of the headset Playing music Playing music Playing music Playing music Playing music Pausing Operation Short press button Short press button Long press button Long press button Short press once Short press once Volume up Volume down Last track Next track Pause play Warning: Excessive pressure form earphones and headphones can cause hearing loss. 7 tone. Notes:
When the volume is adjusted to max or min., you will hear one prompt
If you want to remote control last/next track, pause/play, it needs your Bluetooth cell phone or Bluetooth transmitter paired with the headset to support AVRCP profile, please refer to the users manual of your mobile phone or Bluetooth transmitter for further information. 6. Line out The INCYNC also support line out function.You can use a 3.5mm to 3.5mm audio line to output audio to other devices. You also can connect a wired headset as an output audio device. The picture below shows the line out to the car audio system. 7. LED indicator flashes LED indicator Red and blue LED alternately Blue LED flashes once every 2 seconds Blue LED flashes twice every 4 seconds Blue LED flashes thrice every 4 seconds Red LED flashes twice every 30 seconds Status of headset Pairing mode Not connected to device to device(only Connected connected to HFP or A2DP) Connected to device( connected to HFP and A2DP ) Low battery 8 8. Factory Reset In the status of off , long press and button about 8 seconds and release it until the red and blue LED flashes simultaneously, you will hear dudu tone. Remarks:
After factory reset, the paired list of headset will be deleted. After turn it on again, the headset will enter pairing mode automatically, and you need to re-pair and connect with Bluetooth devices.
Care and maintenance Read the following recommendations carefully before using INCYNC. Following these you will be able to enjoy this product for many years.
Please note that the cord management clips are optional accessory for better wearing.
Keep it dry and dont put it in the dump place to avoid the products internal circuit being affected.
Keep the product away from direct sunlight or hot places. High temperatures will shorten the life of electronic devices, destroy the battery or distort certain plastic parts.
Dont expose the product to cold areas. It may damage the internal circuit board. professional.
Dont try to disassemble the product as it may get damaged if you are not sweat.
Dont let it fall down onto the floor or other hard surfaces. The internal circuit might get damaged.
Dont use intensive chemical products or detergent to clean the product.
Dont scratch the surface with sharp things.
Dont use this product during strenuous exercise. It may get damaged by In case the product doesnt function properly, send it to the store you bought it. The staff will help you to solve the problem 9
FAQs 1.What does it mean when red LED flashes twice every 30 seconds?
Battery is low power, need to be recharged. 2.Why is the red LED off when charging?
a) Please make sure the charging device connect with headset well;
b) The battery may dry up. Please charge the battery for 30 minutes, and then the red LED will be ON. 3.How long is the operational distance of the INCYNC and cell phone?
According the Bluetooth standard, the furthest operational distance of Class 2 Bluetooth products is 10 meters. But the operational distance differs with environment and cell phone. 4. Why cant I hear the sound on the headset?
a) Make sure the headset has been switched on;
b) Make sure the volume is not too low or muted;
c) Make sure the headset connects with the mobile phone correctly;
d) Make sure the distance between the headset and the cell phone is in the available Bluetooth range. 5. Why cant I hear the sound clearly on the headset?
a) Make sure the mobile phone is in the strong signal area;
b) Make sure the headset is in the available range of this product. 6. Why the pause/play, last/next track not function when playing music?
Make sure your Bluetooth device supports AVRCP (Audio/Video Remote Control profile) 10 FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IC RSS warning This device complies with Industry Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that, the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. This radio transmitter (identify the device by certification number, or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. 12 Bluetooth V2.1+EDR HFP,HSP,A2DP, AVRCP 10 meters About 2.5 hours About 3 hours About 250 hours About 3 hours DC 5V/500mAH
Specifications Bluetooth version Bluetooth profiles Operating distance Music time Talk time Standby time Charging time Charging input FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 11 Le prsent metteur radio (identifier le dispositif par son numro de certification ou son numro de modle s'il fait partie du matriel de catgorie I) a t approuv par Industrie Canada pour fonctionner avec les types d'antenne numrs ci-dessous et ayant un gain admissible maximal etl'impdance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. IC Radiation Exposure Statement:
This equipment complies with IC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IC exposition aux radiations:
Cet quipement est conforme avec IC les limites d'exposition aux rayonnements dfinies pour un contrl environnement. Cet metteur ne doit pas tre co-localiss ou fonctionner en conjonction avec une autre antenne ou metteur. 13